Search Documents

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler's saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By George J. Young

The recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may be enumerated as follows: Forman Shaft fire, Gold Hill, April 21, 1903; shaft-house, machinery, and shaft destroyed; loss estimated at $50,000; cause unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery,and shaft in part destroyed; loss estimated at $100,-000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause " probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started ill winze; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911; fire originated in shaft-station from unknown cause; 7 men killed, and $34,-521 damage caused. (Note 1.—On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and lagging of the pump-room. The pump-man in charge notified the surface, and the electric current was shut off. A hose was then turned on the fire, but the dense smoke drove the attendant out. Inspection by the electrician and the shaft-foreman, equipped with oxygen-

Jan 1, 1913

By Perry Harrison

THE mixing of fine ores with fuel and burning under induced draft is called sintering in iron-ore practice and either sintering or roasting in copper and lead metallurgy. The first development of sintering was the Huntington-Heberlein process, in which fine sulfide ores mixed with fuel were charged into a pot and burned under the action of an upcast current of air introduced at the bottom of the pot. Modern development has resulted in two types of machine; the continuous Dwight-Lloyd machine, which consists of heat-resisting grates and a moving beltlike type of hearth constructed of metal, in which air is drawn downward through the bed, and the stationary Greenawalt batch process, which operates in the same manner as the Dwight-Lloyd except that the hearth is stationary. The recent rapid increase in the use of sintering has been the result of two great advances in metallurgical process-flotation and the treatment of flue dust. The Dwight-Lloyd machine is used in many plants for agglomerating flotation concentrates and at the same time reducing the sulfur content to furnace requirements and it has become standard practice to treat iron blast-furnace flue dust by either the Greenawalt or Dwight-Lloyd machine, so that it can be recharged into the furnace. The mining of low-grade magnetite iron deposits and their beneficiating by grinding and magnetic separation resulted in a fine concentrate extremely detrimental to blast-furnace practice. These concentrates are sintered and made into ideal material for blast-furnace use. Incidentally, coke savings of about 400 lb. per ton of pig are reported.

Jan 1, 1930

By S. F. Emmons

In the yew 1879, Congress, acting tinder the advice of tile National Acdemy of Sciences, discontinued the temporary surveys or explorations under Hayden, powell, and Wheeler, and established as a permanent organization the United States Geological Survey, making it a Bureau of the Interior Department. A great step was thus taken toward obtaining the greatest practical results from the expenditure of the public money for geological purposes. The recommendations of the National Academy also contemplated the consolidation of all the various organizations for the mensuration and mapping of the country—-such as the Coast, Engineer, and Land Office Surveys—under one single head; which, also, should assume the duty of providing the mays necessary as a basis fir the work of the Geological Survey. But this useful measure did not meet the approval of Congress, and the various mensuration surveys were left in statu quo. With the final establishment of a permanent Geological Survey of the United States, it became necessary to adopt a plan of work which would enable it in time to take the prominent rank among the older surveys of other civilized nations of the world, which is justified by the great, wealth and mineral resources of the country it is destintd to study. The somewhat vague wording of the organic law under which it was created, directing an examination of the geological structure, mineral resources, and products of the public domain, left the details of the policy to he pursued very largely a matter of discretion with its director. That adopted by Mr. Clarence King, the first director, as foreshadowed in his Annual Report to the Secretary of the Interior for 1880, was one whose distinguishing feature was the prominence that should be given to economical geology, or the practical application of geological investigations to the development of the mineral resources of the country. In earlier Government Surveys, which were topographical reconnoissances in a practically unknown region, geology occupied a secondary and unimportant position. With the Fortieth Parallel Survey, inaugurated in 1867, and its successors, the Hayden, Powell, and Wheeler Surveys, geology became an essential object of the work, but owing to the want of already existing maps topography

Jan 1, 1882

By J. C. Uy, A. A. Burr

A quantitative relationship between the allotropic phase boundaries of zirconium-base binary systenzs and the solute metallic valence is shown through an intermediate thermodynamic parameter. A simplified equation relating this parameter to the phase boundaries is briefly reviewed, and data from the literature are used to show the relationship of this parameter to the solute metallic valence. It has been reported that the solute metallic valence can be used as an index of phase stabilization in zirconium-base binary alloys.' It was shown that the algebraic sign of the slopes of the hcp/bcc phase boundaries of zirconium alloys correspond to the algebraic sign of the metallic valence of zirconium minus the metallic valence of the solute, or, in other words, a solute whose metallic valence is higher than that of the solvent tends to stabilize the high-temperature phase while one whose metallic valence is lower than that of the solvent tends to stabilize the low-temperature phase. Further analysis of the zirconium binary systems has revealed a quantitative relationship between the solute metallic valence and the relative slopes of the two-phase allotropic boundaries. This relationship involves a thermodynamic quantity whose significance can be seen in the following section. PHASE-STABILIZATION PARAMETER Let Qb be the difference between the partial molar heats of mixing of a given solute in the two allotropic phases of the solvent which are in equilibrium with each other at a given temperature, thus A relationship between this term Qb and allotropic phase boundaries has been employed by several au-thors'-= in the evaluation of phase diagrams, and can be briefly derived as follows. Referring to Fig. 1, consider the general case of two allotropic phases, each having a small mole fraction (Xa,Xb) of the solute, in equilibrium at temperature T and atmospheric pressure as represented by the reaction. solute in ß phase =solute in a phase If now a reaction occurs such that an infinitesimal amount of the solute is removed from the ß phase and added to the a phase, there would be a partial molar

Jan 1, 1967

By E. H. Fahmy, L. C. Uren

During recent years, oil producers have observed with interest the practical success which has attended the application of water as a medium for displacement of oil from its reservoir sands in the Bradford field of northern Pennsylvania and southern New York. Here, according to various authorities, additional recoveries of frorn 2,000 to 12,000 bhl. of oil per acre have heen secured by this method, after ordinary flowing and pumping. rnethods of production had practically reached the lower limit of economic operation. Notwithstanding the success which has attended the practical use of the flooding process in the Bradford field, oil producers in other regions are skeptical of its value when applied under physical conditions differing markedly from those which characterizc the Bradford field. Its usc would probably he construed as illegal in most of the oil-producing states. This general relnctance on the part of oil producers in other regions to accept the flooding process is due in large part to lack of infor-n~ation regarding the factors that influence its operation and efficiency. With the purpose of clarifying to some extent the issues involved, and of determining when the flooding proccess may or may not beeffee-tivcly ernployed, the writers have conducted a serics of laboratory exper-imentments under carefully controlled conditions, designed to indicate, the influence of various physical, chemical arid lithologic factors. These experments have not been conducted under conditions identical with those which exist at depths far below the earth's surface, so that direct quantitative comparisons with field results are not justified, hut it is believed that the experimental results at least warrant qualitative inter-pretations that may he applied to field conditions. The methods employed in the conduct of these experiments are briefly explained, and the results, together with the conclusions based thereon, arc presented. FactoRs Influencing Displacement of Oil froM SaNdS by WAteR- flooding Before presenting the experimental data, it, will he desirable to con-sider the manner in which the residual oil is retained within the oil sand

Jan 1, 1928

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.' Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.' Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10' psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By D. S. Jacobus

COMPRESSED-air motors are specially desirable, if economically practicable, for underground haulage, because they require no fuel, involve no danger of fire, and not only avoid heating and fouling the atmosphere with smoke and combastion-gases, but by the emission of expanding fresh air, cool and improve it and aid ventilation. The highest developments in the use of compressed-air motors for locomotion are to be found, in the opinion of the writer, in the principles of the Mekarski car-motor as applied to street tramways, and it is thought that notes taken regarding this system, during a recent trip to Europe, where two plants are in successful operation, at Nantes and Vincennes respectively, will be interesting to mining engineers. The plant at Nantes operates a street-line 5.2 miles long, requiring about twenty motors; the one at Vincennes about 7 miles of road. Each car at Nantes carries its own motor. At Vincennes, however, the motor-car is arranged to tow a second car containing no motor. The road at Nantes is the older, having been in successful operation for ten years, during which time neither the American consul, Mr. Shackelford, who has resided at Nantes for about five years, nor the vice-consul, Mr. Bennett, who has been at Nantes ever since the road started, has ever seen anything go wrong with the motors. DESCRIPTION OF THE RAILROA at Nantes. Motor-Car.—Two small engines are connected' so as to rotate the front axle of the car, a reversing lever being used to alter the cut-

Jan 1, 1891

By W. A. Mudge

ONE of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of con-struction. Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid; of which the present limitations of design may be overcome. The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion. The corrosion resistance of metals and alloys is never absolute and all-inclusive; a particular alloy will withstand some corrosive conditions well and fail utterly tinder others. Furthermore; other properties, physical and mechanical, required in-conjunction with corrosion resistance vary considerably for different commercial applications. One wants a soft, ductile sheet metal resistant to atmospheric corrosion; another, a high-strength- alloy resistant to sulfuric acid. The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys. In June, 1924, a symposium by the American Society for Testing Materials, on Corro-sion-Resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance

Jan 1, 1935

By W. M. Peirce

COMMENCING in 1922, each year a lecture has been presented to the Institute of Metals Division at this February meeting. The range of subjects has been very broad. Some speakers have dealt with the most advanced work in the very heart of the science of physical metallurgy. Others have stimulated our imaginations by discussing the most recent progress in related fields of science. Others have told us of the latest art, which is at any moment of greater practical importance than the latest science, of metals. I feel that this broad precedent in the choice of subjects will justify my choosing to talk about some of the prosaic details of how, during the last generation, industry has effectively organized research to accelerate progress in our own and all other fields of science and related art. A number of years ago I visited one of this country's well-known research laboratories and had the pleasure of chatting for a few minutes with its equally well-known director. Being particularly interested at the time in the organization problems connected with industrial research, I broached that subject. My host stated in effect that he didn't believe in organized research. He was, of course, resorting to a rhetorical hyperbole to point out the danger of overorganization which can so easily drift into regimentation and destroy individual initiative. Actually nearly all of us, much as we cherish our personal freedom of action, believe in organization because the history of progress in every field of human activity has been a history of men learning to work together, to cooperate, to create an efficient division of labor. We use organization to achieve this coordination. At the same time our form of organization must not stifle individual initiative or it will prove a deterrent rather than an aid to accomplishment. Research, too, must be organized for greatest achievement but especial skill and care are perhaps needed to avoid stifling the initiative of the individual workers. I have, of course, followed with keen interest and much benefit the vast amount that has been said and written on this subject in the past twenty years but I still find new stimulation in discussions with my good friends working in this field. It is my hope that this discussion may serve a like purpose. It would be ungracious not to make due acknowledgment to the many able contributors to this particular phase of human progress, but their very number and the great volume of their writing makes it impossible to trace to any one individual a particular significant and valuable idea. I shall content myself therefore with this general acknowledgment and with acknowledgment of the specific debt that every research man owes to those who have so ably kept before the public, and in particular before industrial executives, the place of research in the modern scheme of things. Because of the legitimate publicity thus given to research, the day is past when any

Jan 1, 1944

By George Rice

VENTILATION of underground workings to fur-nish air of good quality to workers is now the accepted practice for all kinds of mining; but in coal mining it is also a requirement vital for safety to have systematic coursing of the air to all parts of a mine so that fire damp can be diluted and carried away. These two basic needs are recognized in the codes of every country or State where coal is mined, and each has its own system of ventilation requirements. With the same fundamental requirements, varying in degree but not in kind, the surprising thing is that these and other features of regulatory codes should vary so-wide-ly that their provisions on the same subject bear hardly any resemblance to one another. This was strikingly brought out in the paper given before this institute in 1926, on "State Coal-Mining Laws Concerning Ventila-tion1. The explanation ordinarily is that the geologic forma-tions and the mining conditions and methods differ in the various coal fields. Although that is true, in most countries and States the variations in the differ-ent mining districts within each country or state vary widely, and the respective codes must be made to apply by special provisions to meet the variations in thickness of coal, depth,. dip, character of roof, and presence or absence of gas. Evidently the great diversity in codes is due to the method of formulating them. Some are prepared by political commissions in which partisan interests are a factor; others originated in the early days of mining with meager outlines and were so amended by legisla-tive acts or administrative orders from year to year as to become complicated and ambiguous, and pro-visions in different parts of a single law are often contradictory. Such laws have therefore been difficult to interpret and to enforce adequately.

Jan 5, 1928

By Donald L. Katz

Charts for predicting the pressure to which natural gases may be expanded without hydrate formation have been prepared for gases of even gravity. Pressure-temperature curves for hydrate formation were established for gases having gravities from 0.6 to 1.0. These curves and the thermal behavior of the gases during free and adiabatic expansion were used to prepare the charts for estimating the permissible expansion of natural gases without hydrate formation. The problem was solved by L. F, Albright, W. T. Boyd, J. J. McKetta, G. Martin, P. Poettman. and A. P. Snyder.-, who are first-year graduate students in the department of Chemical and Metallurgical Engineering at the University of Michigan. This paper is essentially a summary of their results. Prediction of Conditions for Hydrate Formation in Natural Gases Each natural gas under a given pressure will form solid hydrates at a corresponding temperature provided sufficient water is present.1-5 The temperature of natural gases below about 5000 lb. per sq. in. decreases when the gases are expanded freely.6,7 This decrease in temperature may cause the expanding gas to enter the region of temperature and pressure at which hydrates will form' The final pressure to which a natural gas may 'be expanded without hydrate formation depends upon the initial temperature and pressure and the gas composition. This paper presents charts that give the final pressures to which gases of gravity 0.6 to 1.0 at given initial temperatures and pressures may be expanded without formation of hydrate. Hydrate-forming Temperatures and Pressures as a Function OF Gas -Gravity Experimental data of pressure versus temperature at which solid hydrate will form, provided sufficient water is present, are available for a series of gases.2,3 A method of predicting the pressure-temperature curve for a given gas composition has been reported.' The solution to this problem requires that these curves relating pressure to temperature be established for gases of given gravities.

Jan 1, 1945

Primarily, 1961 was a year for widespread application of tools and techniques which have become operational in the past several years • • • Raising --Raise climbers and climber raising techniques have been improved; narrow veins as low as 55° dip are now being mined from climber raises. Climber modifications include: larger motors, tighter radius curves negotiated, improved lubrication and new methods of stowing the climber during a blast. Climber raises are now ventilated in several ways: a 12-in. diam flexible vent tube behind the climber rail; a 6-in. diam pipe behind the climber rail (with fan); or a 6 to 8-in. diam drill hole along the axis of the raise. In hot raises, these ventilating techniques have resulted in more rounds per shift. When driving raises from crosscut and lateral development, mucking machine loading of raise rock is preferred over slusher ramp loading for the following reasons: a) faster set-up and teardown of climber facilities; b) easier access for climber maintenance, repair and loading of raising supplies; c) area at the bottom of the raise can be kept cleaner. Both wide and narrow veins are mined from 7 x 7-ft climber raises at Butte and at Republic, Wash. At Republic, climber rollers have been modified to support increased weight when driving 55°dip raises • Drilling-The new largebore, short-stroke push feed drills are much faster drilling than previous models and are most satisfactory in hard ground. Although reports on maintenance studies of the new drills are not yet available, increased steel and bit wear and breakage, and increased drill maintenance are seen as potential problems. Mines in Montana and Idaho continue to test rubber-collared drill steel. The fabricating methods used are successful but advantages in increased steel life have yet to be proved. Underground applications of down-the-hole drills continue. Drilling speed and accuracy are reported as the outstanding advantages. Manufacturers are now hopeful of making drills which will operate in any direction. Present applications are for ventilation holes (to 8 in. diam) for climber raises, holes for hydraulic fill distribution, drain holes and "predrilled" raises. Good drilling accuracy has been reported to a depth of 200 ft. Cutting holes in drifting is seen as a future application

Jan 2, 1962

By Eugene Guccione

For at least a decade, the energy crisis was accurately predicted by a small number of industry people who were ignored until last year, when they suddenly found themselves accused for their "lack of planning" and "greed." With the worsening shortage of natural gas and oil, the current scramble is for alternate energy sources-which means: a big rush into coal and uranium mining. (Some big plans are also on the drawing boards regarding geothermal steam, oil shale, tar sands, and even solar energy. But developing such new industries from scratch would be difficult enough even in a healthy economic climate-which is not exactly what the country currently enjoys.)

Jan 8, 1974

By Edward W. Mehal

This paper presents a review of the technologies which have been used in the application of III-V compound semiconductors to integrated circuits and arrays. These materials have properties which make them useful for various devices such as: light emitters, sensors, microwave sources, and microwave diodes. Technologies for incorporating these devices into integrated circuits have been reported and processes developed for fabricating planar devices using selective epitaxial deposition or selective diffusions. Isolation methods utilizing semi-insulating GaAs, oxide isolation, and ceramic insulation have also been reported. These techniques, and the devices and circuits produced or proposed are discussed. AFTER the invention of the silicon-integrated circuit, methods for utilizing compound semiconductors for integrated circuit applications were proposed. The scope of applications was potentially much broader because of the range of properties available from these materials. There also was the opportunity of coupling these properties with germanium and silicon devices to realize functions and circuits which could not be produced with silicon monolithic circuits. Table I exemplifies the range of electrical properties available in III-V compound semiconductor materials which are currently being widely used. A wide range of sensor and emitter applications result from the range of band gap. The band structure of GaAs and GaAsxP1-x permits their use as microwave oscillator source, and the high electron mobilities further facilitate their utility in microwave devices. The concept of "integrated functions"1 results from the availability of these materials and methods for utilizing their special properties. Heteroepitaxial growth allows the fabrication of a monolithic block of these materials. Semi-insulating GaAs permits the attainment of electrical isolation between components in a monolithic block without resorting to p-n junction biasing or oxide isolation methods. An "integrated function" is a unit which can perform a system or subsystem role and perform a number of electromagnetic functions. These functions could include sensor or input transducer, signal processing, interconnections, and control or output function. Two examples which demonstrate this concept are an optoelectric processor and a microwave receiver front end. The optoelectronic processor, Fig. 1(a), would consist of a light sensor, signal processor, and output emitter. The sensor could be InSb or InAs which would be IR-sensitive. The signal from this sensor would then be amplified and transmitted to the light emitter. The amplifier could utilize GaAs bipolar or field effect transistors. A Gap emitter would then produce visible radiation. The microwave receiver front end, Fig. l(b), would consist of a local oscillator section and a mixer section. A signal input from an antenna is mixed with the signal from the local oscillator. The local oscillator signal is produced by a Gunn oscillator. The single-ended mixer utilizes one Schottky barrier mixer diode. The IF signal would then be amplified further and suitably displayed. A further extension of the capability of utilizing the

Jan 1, 1969

THE 127th meeting of the Institute was held in New York, Feb. 19 to 22, 1923. In addition to the usual large volume of technical matters under consideration, the meeting was particularly noteworthy for the amount of attention given to its business session; the convention of local section representatives also was full of interest. The total registration was 1201. The annual business meeting on Feb. 20, President Dwight presiding, was attended by 125 members, who listened with marked attention to the reports and addresses of the several officers. The chairman departed from the stipulated order of business in order to allow more time for the presentation of remarks on the state of Institute affairs. The previously pub-lished reports of the officers were accepted, as printed. On the report of the tellers, the following officers were declared elected: E. P. Mathewson, Director and President-District 0 T. T. Brewster, Director and Vice-president-District 6 Frank M. Smith, Director and Vice-president-District 11 W. H. Aldridge, Director-District 0 G. H. Clevenger, Director-District 1 A. N. Diehl, Director-District 3 Reno H. Sales, Director-District 7 Seeley W. Mudd, Director-District 10

Jan 3, 1923

By R. L. Braun, D. L. Leach

Laboratory experiments simulating in-situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen are reported. Copper extraction and acid consumption data are correlated with temperature in the range 50 to 150°C and quenched pH in the range 0.25 to 2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1977

By J. E. Spruiell, F. H. Patterson, B. F. Shuler

The microstructures and textures developed by the working of high-purzly thermochemically deposited tungstem sheet have been inuesligated. Greater than 60 pct reduction was required to deslroy the columnar grain structure which existed in the as-deposited sheet. With increasing reductions the texture gradu-ally charged from the initial as-deposited orientation with (100) parallel to the sheet normal to a (100}(011) ideal ovienlation with some spread about the rolling direction. This texture was retained after recrystalli-zation a1 2000°C. THE processes for depositing tungsten by hydrogen reduction of tungsten hexafluoride have been under development for the past several years.1,2 The nature of the deposition process is such that the as-deposited material contains a highly oriented columnar grain structure perpendicular to the deposition substrate. This well-defined columnar structure may be useful in certain applications293 but a wrought or equiaxed structure may be desired for some components such as tubing. Knowledge of the effects of working ther-mochemically deposited (TCD) tungsten is therefore necessary in order to establish the feasibility of obtaining worked and recrystallized microstructures and textures. The details of a recently developed technique for thermochemically depositing flat, uniformly thick tungsten sheet are presented with emphasis on the effects of deformation by rolling on the microstructure and texture. Although no work has been previously reported on the rolling and the annealing textures of TCD tungsten, there have been some determinations of textures for cold-rolled tungsten foil prepared from powder-metal -lurgy billets.4-8 The general description is that of a predominantly lurgy{100}(011) texture, with some spread about the rolling direction as an axis. pugh5 reports data both for cold-rolled and for annealed foil having about 96 pct initial cold work. He observed no change in texture, except for a decrease in the spread, for annealing treatments of 30 min at temperatures up to 1800°C. On annealing at 1900°C, both the low-temperature components plus new components which were described alternately as {001}(320) plus {001)(230) or as {100}(011) ± 12 deg about the sheet normal were observed. Above 1900°C, the new orientation existed alone, and it was stable up to 2500°C, the highest temperature that Pugh investigated. THERMOCHEMICAL DEPOSITION OF TUNGSTEN SHEET High-purity tungsten sheet was reproducibly deposited on the inner walls of a molybdenum mandrel by the thermochemical reaction WFs(g) + 3H2(g) - W(s) + 6HF(g). The mandrel was heated by a five-zone tube furnace which afforded a controllable fixed-temperature profile. Sheets measuring 1+ by 12 in. have been deposited with uniform thicknesses of up to 0.145 m. As shown schematically in Fig. 1, the purified reaction gases were metered into a mixing chamber at a Hz-to-WF6 ratio of 15 and preheated to 350°C. The flow rate of the WF6 was 300 cu cm per min at stp. These gases were directed through a conical injector into the deposition chamber. Inside this chamber hydrogen reduction of the WF6 to pure tungsten metal occurred on the hot walls of the molybdenum mandrel at a total pressure of 5 Torr. Typical temperatures for the five zones in the chamber were, respectively, 565", 540", 550°, 570°, and 590°C. The hydrogen fluorlde generated from the reaction, the excess hydrogen, and some un-reacted WF6 were pumped on through the scavenger

Jan 1, 1968

Until the end of 1960, the small primary aluminum industry in Australia was run by the government. The entire operation was at Bell Bay on the north coast of Tasmania. It consisted of an alumina plant and smelter, owned jointly by the Commonwealth and the State of Tasmania. Apparent domestic demand that year was about 48,000 long tons; 11% thousand came from Bell Bay; the rest was imported. By March 1964, Australia had two fully integrated aluminum companies. The government has stepped out of the picture and the key word of the industry from bauxite to metal is "growth." Present annual capacity of the two companies for making aluminum metal totals 92,000 long tons a year. Australian demand is about 60,000 tons. By 1968 Australian consumption should be 90,000 tons and by 1970 it is expected to reach 107,000 long tons per year. Export markets for bauxite, alumina and metal are developing.

Jan 10, 1964

By E. C. Wright

THE following article is based on observation of college graduates entering the steel industry in technical work made during the past 25 years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many, colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel' plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training -in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers, it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry, physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate's lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature, and that students be taught to use theoriginal data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallography, etc., but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a, few weeks in a. plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1946