Search Documents

By W. N. Poundstone

The mining and ventilating system used in development work in the Pittsburgh Seam in northern West Virginia is discussed. The seam conditions and the nature of the accompanying methane gas are described. The type of equipment and the mining cycle will be discussed, showing how they are well suited for very gaseous development work. Face ventilation in development work is possibly the fastest growing problem of the industry. The coal mines of the future will be faced with the prospect of mining from under increasing depths of cover. Consequently, larger and larger amounts of methane gas probably will be found. The Pittsburgh Seam, in northern West Virginia, is an example of an area already faced with this problem. At the present time, most of the development work being done in this seam lies beneath 500 to 1200 ft of cover. The Pittsburgh Seam in this area has always been very gassy—even near the outcrop—and the recent development work has been accompanied with extremely large volumes of gas. In many cases, a single development section has liberated in excess of 1,000,000 cfm in 24 hr. This problem of heavy gas liberation was the chief concern, several years ago, when continuous mining equipment was first considered at Christopher Coal Co. All of us were apprehensive about the liberation that would accompany rapid extraction in a single working place. However, the experience during the past few years has shown that this ability to mine only one place at a time, is actually the key to working this type of coal. With all of the mining or advancement concentrated in one place, the ventilation can also be concentrated. By this it is meant that continuous mining permits the active working place to be ventilated with a maximum amount of fresh air, taken directly from the intake source without first passing another working place. Continuous mining (and a good ventilating system) also permits a much greater concentration of attention or vigilance to the actual working place. There are two things that are very important to the mining of coal having high rates of liberation. First, adequate volumes of air are necessary. Second, and perhaps more important, a mining and ventilating system must be used that will provide an uninterrupted flow of air to every portion of the working section. Liberations of this magnitude take only a few seconds of interruption for a dangerous accumulation of gas to occur. With adequate volumes of air available, the ability to concentrate ventilation more than offsets the concentration of gas emission that is inherent with continuous mining. The mining system used with continuous mining equipment at Humphrey Mine is similar to the system used at many mines in the area for development work. This system is designed to favor ventilation, realizing that other efficiencies are meaningless if the equipment must stop because of ventilation difficulties. This plan is especially well suited to minimizing ventilation interruptions. Basically, the overall plan of mining is to develop headings into virgin coal and encircle or block out large areas. These blocks are generally at least 2000 ft sq. The purpose of this blocking out is to bleed gas from the area before pillaring. Experience has shown this method to be quite effective, even in the most gassy areas. The gas in this field seems to migrate or flow readily from the solid coal into the outside return headings of the development work. The numerous clay veins and slips that are found in the area are extremely good avenues for gas flow. A block of coal, surrounded with development headings, usually bleeds off readily; and since it is cut off from the virgin coal, it is not subject to gas migration, through the seam, from this source. However, the outside return of the encircling development work, adjacent to the virgin coal, may liberate gas for years. This liberation from the outside ribs in the virgin coal is the reason split ventilation is used in development work. If split ventilation were not used, there would, in many cases, be a serious build-up of gas in the intake before it could reach the working face. Fig. 1 shows a typical development section having seven headings. The two outside places on each side are returns, and the three center headings serve as intakes. This section is equipped with a ripper-type continuous mining machine. An off-track loading machine is used to load from a surge pile on the

Jan 1, 1961

By Vincent T. Ricca, Kurtis Chow

When dealing with acid mine drainage as to treatment levels, costs, and evaluation of abatement schemes, predictions of the quantity and quality of the discharges are needed. An acid mine-drainage model is presented in this paper. In essence, the model is a hybrid of computer programs for stream flow simulation and acid mine drainage. Two major aspects of the model are discussed: mine-water generation and acid-load production. The former is based on hydrologic concepts and the latter on pyrite oxidation kinetics and oxidation product removal. The total model is programmed for the high-speed digital computer. The major inputs are: climatological, basin characteristics, and mine characteristics data. By the use o f the hydrologic model the amount of water that flows through the pyritic system is determined. From this information, acid loads removed by leaching, inundation, and gravity diffusion are then predicted. The outputs from the total model are: average daily mine-water discharge, the associated acid concentration or load, plus the average daily flow in the receiving streams or at basin outlets. The capabilities of the separate models have been tested individually and the joint model has been applied to a small drift mine in southeastern Ohio.

Jan 1, 1975

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

By Charles Burgess

THE improvement, in the quality of cast iron by means of alloy additions has been a metallurgical accomplishment of recent years. Work in this field has shown that chromium is one of the most effective of such additions but, in general, the influence of chromium has been studied only in. connection with other alloying additions, with irons other than foundry irons, or with relatively high percentages of chromium. The present study was initiated for the purpose of determining the influence of small additions of chromium (0.25 to 1.00 per cent) on the quality and resultant properties of cast irons of various foundry grades. The effect of small chromium additions on cast iron was investigated with particular reference to casting characteristics, hardness vs. section, strength, machinability, heat resistance and structure. MATERIAL TESTED Three separate types of cast iron were investigated as to the effect of small chromium additions. The first series of these irons was prepared from remelted foundry cast iron at the Union Carbide and Carbon Research Laboratories, and the other two -series consisted of cupola melts made under usual operating conditions. The first series was made by melting 30-lb. charges of foundry scrap iron containing - 2.86 per cent carbon, 2.72 silicon, 0.50 manganese, 0.062 sulfur and 0.794 phosphorus in a carbon resistance furnace. The chromium was added as high-carbon ferrochrome just before pouring. The irons were cast at approximately 1250° C. (2282° F.). The analysis and physical properties of these irons are given in Table 1, test 1. The second set of cast irons was made in a cupola in accordance with normal practice, 'the charge containing approximately 42 per cent steel scrap and the chromium additions being made to the ladle. Analysis and tests of these heats are shown In Table 1, test 2. A small amount of copper was present in heat C of this series.

Jan 1, 1932

By T. A. Rickard

The question of the original extent of the anthracite-beds of Pennsylvania has often been raised; and even discussed with reference to the probability of their present existence under the New Red, a matter of immense practical importance. So high an authority as my revered master, J. P. Lesley, Honorary

Jan 1, 1903

By P. A. Beck, A. Merlini

Quantitative texture determinations were made for rolled and for rolled and annealed strips of 3, 6, and 10 pct Zn brasses. The main components of the rolling texture gradually shift over a wide composition range from the orientation characteristic of copper to that of 70-30 brass. At least the main features of the corresponding gradual changes in the annealing texture may be accounted for qualitatively on the basis of the oriented growth theory of annealing textures. All the oriented nucleation-type theories are notably less successful in accounting for the observed textures. EARLIER investigations by von Goeler and Sachs,' Dahl and Pawlek,' and Brick, Martin, and Angier" suggested that the annealing texture of copper is more sensitive to the addition of solute elements than the rolling texture. It was reported3 that the cube texture changes over into a brass-type recrys-tallization texture on addition of about 1 pct Zn, while the deformation texture changes only at about 5 pct Zn. Such behavior would be difficult to reconcile with any theory of annealing texture formation that relates the annealing texture to the deformation texture. In particular, the oriented growth theory of the cube texture" is based on a certain orientation relationship between the cube texture and the main components of the deformation texture which could not be reconciled with the reported behavior of low brasses. It was, therefore, of interest to re-examine these textures by means of the quantitative methods now available. The deformation and annealing textures of rolled a brasses with approximately 3, 6, and 10 pct Zn have been determined in terms of (111) and (200) pole figures. Experimental Methods The chemical analyses of the Cu-Zn alloys of commercial purity used in the present work are given in Table I. Chill-cast bars of the tabulated compositions were rolled and annealed according to the following schedule: I—rolling from 1.2 to 1.02 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 2— rolling from 1.02 to 0.867 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 3—rolling from 0.867 to 0.600 in. thickness, 31 pct reduction area, annealing 2 hr at 540°C; 4—rolling from 0.600 to 0.400 in. thickness, 33 pct reduction area, annealing 2 hr at 480°C. In the final straight rolling of 96.25 pct reduction area, the strips were reversed end to end after each pass. The final annealing temperature was determined for each alloy by annealing specimens of the cold-rolled strips in salt bath for 5 min at varying temperatures. The results of the hardness measurements are given in Fig. 1, where the final annealing temperature used for each alloy in determining the annealing texture is indicated by a cross.

Jan 1, 1956

By M. Prats

The effect of a sand-filled vertical fracture of limited radial extent and finite capacity (fracture capacity is the product of the permeability and width of the fracture) on the flow behavior of a cylindrical reservoir producing an incompressible fluid through a centrally located well has been investigated mathematically. The shape of the lines of equal pressure near the fracture is essentially independent of the size of the reservoir, provided that the field radius is of the order of the fracture length or larger. For reasonable values of production rates and of fluid, reservoir and fracture properties, the total pressure drop between the end of the fracture and the well is gelrerally negligible compared with the pressure drop in the reservoir. With regard to production response, the effect of vertical fractures can be represented by the production response of an equivalent or effective well radius. For a high-capacity fracture, the effective well radius is a quarter of the total fracture length, decreasing with the fracture capacity. When invasion effects are simulated by decreasing the width of the damaged zone with distance from the well, the effect of formation damage around a fracture on the production response is not so seriolls as indicated by the literature. This suggests that frac fluids with a conventional filter-loss response are better than high-spurt-loss frac fluids, provided the effective permeability of the damaged zone is the same. INTRODUCTION This paper considers the effect of the fracture capacity, as well as the formation damage which can result from fracture treatments, on the productive capacity of vertically fractured wells. Other publications, notably those of van Poollen,l,2 consider these same effects. In addition to providing more general results for vertical fractures than are available from the liter- ature, the present paper gives the equivalent well radius of fractures having different lengths and capacities and, also, includes pressure distributions in and around the fractures. The effect of a damaged zone around a fracture on the production response was not found to be so great as that reported by van Poollen. 2 This difference probably stems from the fact that we consider a damaged zone which is widest (but is still small) near the well and thins out toward the extremities of the fracture, whereas van Poollen considers a damaged zone having a uniform width for the entire fracture length. Simple, but adequate, equations which describe the effect of these variables on production response are presented (in Appendixes A and B). Thus, results can easily be extended to values of the variables not specifically considered here. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The liquid is incompressible. It is assumed that, after the well is fractured, the cylindrical outer "boundary" is at a uniform potential, provided that it is not too near the fracture. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir).3 Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir described above. If gravity effects are neglected, the flaw behavior in the reservoir will be independent of the vertical position ill the oil sand. This means that the flow behavior in the fractured reservoir can be described by the two-dimensional flow behavior shown in the horizontal cross section of the reservoir, Fig. 2. PARAMETERS The effect of a fracture on the pressure distribution in the fracture itself and in an otherwise undamaged (no skin) reservoir indicates that the pressure distribution is a function of three parameters.

The earliest record of coal in Indiana is one of the earliest in the country. At the close of the French and Indian War, in 1763, the famous Indian trader, George Croghan, was sent from Pittsburgh on a mission to the western Indians. His party met that of a hostile chief on the lower Ohio and was captured, and were taken up the Wabash River; on June 22nd, he passed the mouth of the Vermilion River-probably the Big Vermilion-and on June 23rd, he made the following entry in his journal: "on the South Side of the Ouabache runs a high hank, in which are several very fine coal mines, and behind this bank, is a very large meadow, clear for several miles."' The mines, of course, were outcrops. A few days after this he met some Indian acquaintances who secured his freedom. This location was at Ouicatanon, 210 miles from "Port Vincent," which was destroyed a few years later, and in what is now Fountain County, probably near Coal Creek. Croghan was familiar with the coal already being worked at Pittsburgh. Surveyors who ran the township and section lines in the first ten years of the last century noted the presence of coal and marked its position on the maps in 1804.2 The next record is by Nicholas J. Roosevelt, who in 1809 examined the Ohio and Mississippi Rivers prior to starting building the first steamboat to navigate these rivers. "Not only did he do this, but finding coal on the banks of the Ohio, he purchased and opened mines of the mineral; and so confident was he of the success of the project on hand, that he caused supplies of the fuel to be heaped upon the shore, in anticipation of the wants of a steamboat whose keel had yet to be laid."3 It is probable that this account confused the date of seeing the coal with that of mining it, as an earlier account by another relative of Mrs. Roosevelt of the first trip of the steamboat New Orleans in 1811 is as follows:

Jan 1, 1942

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By Homer Staley

THE casting alloy 88 copper, 10 tin, 2 zinc, commonly known in England as Admiralty metal and in this country as Government bronze, gun metal, or Naval Department composition G, has, at its best, many valuable properties. However, its physical properties are known to vary widely with slight changes in method of manufacture of the castings, such as slight variations in composition, variation in pouring temperature, kind of mold used, method of pouring and gating of molds, size and shape of castings, amount and kind of heat treatment., and so forth.1 The microstructure of castings made from this alloy is influenced by slight variations of composition, rate of cooling, and kind and length of heat treatment. This is best understood by reference to the equilibrium diagram. The part of the diagram in which we are interested and the effect of the thermal equilibrium relations on the physical properties of the alloy 88 copper, 10 tin, 2 zinc, have been discussed by Hoyt, Camp-bell, Primrose, and Rawdon.2 In Fig. 1 is given the equilibrium diagram of the copper-tin alloys. Briefly stated, the relations of composition and temperature changes are as follows. Compositions between A and a consist of but one constituent-the a bronze, which is a, solid solution of copper and tin, rich in copper. On cooling from the molten state these compositions gradually crystallize, at temperatures above 790°, into a mass of interwoven tree-like crystals or dendrites. The cores of the dendrites are rich in copper and the percentage of tin gradually increases as the surfaces are approached. As cooling progresses, after all the metal has crystallized, no further changes occur, in the crystals other than diffusion within the crys-

Jan 9, 1919

By William M. Baldwin, T. S. Howald, A. W. Ross

EXPLORATORY WORK THE related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal [ ] strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strips-20.29 and, to a lesser extent, yield strength7,11,17 and stress-strain curves" have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between earing tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture, a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1945

By C. Elbaum

Specimens consisting of several crystals, each with a prescribed geometry and a controlled orientation with respect to both the extermally intposed stress and the highboring crystals, werer deformed in tension at room temperature. It is shown that the influence of a grain boundary on the plastic defolrmation of a mullicrystal depends on the extent to which the presence of the grain boundary, contributes to the necessity 01. multiple slip in the component crystals. MANY investigations were carried out in the past on the plastic deformation of aluminum single crystals, bicrystals, and polycrystals. The various studies of bicrystals aimed primarily at elucidating the influence of grain boundaries on the mechanisms of plastic deformation. In the earlier studies the emphasis was placed primarily on finding the "strength" contributed by a grain boundary. In more recent investigations it became apparent that the grain boundary does not contribute any strength per se but rather acts by influencing the mechanism of plastic deformation in the adjoining grains. The concept thus emerged of the plastic properties of a bi-crystal, and by extension of a polycrystal. depending solely on the mechanism of deformation prevailing in each grain. The contribution of the grain boundaries thus becomes limited to the type of restrictions imposed on each grain by its neighbors. The present investigation of the behavior of specimens consisting of more than two crystals was designed for the purpose of studying the influence of the grain boundary in simple aggregates. The findings of this study further support the concept that the restriction imposed on a deforming crystal by its neighbor constitutes the predominant factor in the plastic deformation of polycrystals. The term "multicrystal", in contrast with single and polycrystals, is used to describe specimens consisting of several crystals. Each one of the component crystals has a prescribed geometry and a controlled orientation with respect to both the externally imposed stress and the neighboring crystals. Two groups of multicrystals were prepared. All the component crystals of both groups of multicrystals had the axial orientation (isoaxial multicrystals) shown in Fig. 2, with the primary slip plane and slip direction both at 45 deg to the specimen axis. In the first group (hereafter referred to as group I) the component crystals were symmetrically oriented with respect to the plane of the grain boundary; the primary slip plane and slip direction were respectively at an angle of 60 and 30 deg to this plane. For the second group (group 11) the axial orientation remained the same and the relative positions of the primary slip plane and slip direction are shown in Fig. 3. EXPERIMENTAL METHODS The material used was aluminum 99.993 pct pure, according to the manufacturer. The specimens were produced by growth from the melt in a horizontal graphite container. In order to maintain the prescribed geometry of the individual crystals of a multicrystal, a technique described elsewhere was used.' The specimens were grown under a small, positive pressure of helium at a rate of approximately 1 mm per min. annealed in air for 24 hr at 640°C and cooled over a period of several hours to room temperature. All the multi-crystals were rectangular in cross-section, 6 by 18 mm (see Fig. 1) and from 150 to 170 mm long. In each group bicrystals, tricrystals and quadru-crystals were prepared as shown in Figs. 1 and 4.

Jan 1, 1961

By Falih Ergunalp

REGULAR production of chrome in Turkey started in 1860 with the operation of the Bursa deposits (5, Fig. I). Others were discovered at Makri, near Fethiye (3, Fig. I). For 33 years Turkey remained the principal source of this mineral. While new discoveries were coming in elsewhere, Turkey's output declined until 1921, as a result of four successive wars, which ruined the economics of the country. In 1927 a revival came with the production of 18,000 tons. In that year the Société Minière de Fethiye was formed. This company now operates mines in the Vilayets of Aydin, Denizli, Burdur and Mentese, and it has reached a maximum production of between 80,000 and 90,000 tons annually. The Turkish output therefore increased from 29,000 tons in 1930 to 55,000 tons in 1931; and to 119,009 tons in 1934. The second phase in the increase in chrome production in Turkey came about in 1935, when the Government decided to reorganize and control the mineral industry of the country according to the principles of "government control" of the present regime. Up to that time the mineral resources of the country had been exploited by private concerns. In 1935, the M.T.A. (Maden Tetkik ve Arama) Institute (Institute of Mining Research and Geological Survey) was established by the Government to do the geological and geophysical survey work and discover new mineral resources for the country. Before the establishment of the M.T.A. Institute, the chief chrome-producing region was Fethiye (3 and 4, Fig. I). As a result of the extensive work of this bureau, many new chrome deposits have been discovered and are now in production. The operational field of the mineral industry was given to Eti Bank, another Government-sponsored and Government-controlled establishment. Eti Bank gradually took over the exploitation of existing mines by purchasing them from privately operated companies. Attention was first given to the Zonguldak collieries and to the different chrome deposits scattered over the country. The Guleman mines (14, Fig. 1) were developed and put in operation in 1936. Since then the bulk of Turkish chrome output has come from this mine, which yields the highest grade ore in the world (averaging 52 per cent Cr2O3). In 1939, the recently discovered chrome deposits to the north of Eskisehir went into production, yielding ore having a Cr2O3 content of 51 to 52 per cent. Today, more than ever, the efforts of both the M.T.A. Institute and the Eti Bank are concentrated on finding new deposits and placing them in operation. There are still many promising regions of the country that merit systematic surveying and prospecting for chrome ores. Thus it is probable that Turkey will continue to make noteworthy progress in chrome output. As the annual chrome production of

Jan 1, 1944

By Hollis L. Caswell

The present status of integrated circuits utilizing. superconductive switching. elements is reviewed with special attention given to fabrication techniques, methods for interconnecting completed circuits, and refrigeration requirements. Cryoelectronics has been largely an "inte- grated-circuit" technology since its conception because the switching speed of superconductive devices is attractive only when these devices are fabricated with thin-film techniques. It is true that cryotron circuits can be constructed from wires of appropriate materials (as indeed was done by Dudley Buck 1 in his early investigations) but these circuits will switch in times characteristic of milliseconds whereas similar circuits fabricated by thin-film methods have potential switching times of nanoseconds. Furthermore, cryo-electronic devices such as the cryotron lend themselves readily to fabrication by thin-film techniques since these components may be made from polycrys-talline thin films and are relatively insensitive to the presence of impurities (as measured by semiconductor standards). Therefore, during the past decade considerable effort has been devoted to developing techniques for batch fabricating circuit arrays containing superconductive switching elements. Technology had developed to the point several years ago that fabrication of cryoelectronic arrays containing up to one hundred devices was rather straightforward. However, larger arrays containing between lo4 and 106 components which are required for commercial development of cryoelectronics still pose very severe yield problems. Thus in a sense cryoelectronics found itself in 1962 at the point semiconductor technology finds itself today; namely, individual devices and small groups of integrated devices could be fabricated with acceptable yield and the outlook for building larger integrated-circuit arrays was bright. Unfortunately, problems associated largely with yield have made fabrication of these larger arrays difficult. Unlike semiconductor technology, cryoelectronics had to solve the problems of large-scale integration before it could become economically attractive. This has proven to be a sizable burden to bear. Since several reviews exist on superconductivity,2 superconductive devices,3 and cryoelectronic technology, no attempt will be made in this paper to summarize these areas. Instead a few specific topics will be dealt with in more detail. First, a brief description is given of selected superconducting switching and storage devices with special attention to several metallurgical techniques which improve the performance of these devices. Second, techniques used to fabricate cryoelectronic devices are described with emphasis on problems affecting yield. Third, techniques for interconnecting a number of cryoelectronic planes are described. And last, refrigeration of cryoelectronic components is discussed briefly since the low operating temperature of superconductive devices is an important consideration in this technology. SUPERCONDUCTING STORAGE AND SWITCHING DEVICES The basic superconductive switching device is the thin-film cryotron. The geometry of this device is attractively simple, since it involves only the intersection of two lines that are electrically insulated from each other. The switching element (gate) and control element (control) of a crossed-film cryotron are arranged as illustrated in Fig. 1. The material for the gate is selected to permit the gate to be switched from the superconducting to the normal (resistive) state by the application of a control current. Tin, which has a critical temperature (T,) of 3.7°K, is commonly used for the gate and the cryotron is operated at a temperature just below T, (for example, 3.5°K). The control material (normally lead, with T, = 7.2°K) is chosen so that the control is never driven normal during circuit operation. To improve cryotron operation, a ground plane, also of lead, is placed under all of the circuitry to act as a diamagnetic shield and improve the current-density uniformity across the width of various thin-film elements. Normally, line widths vary from 0.005 to ^ 0.020 in. and film thicknesses from 300 to 10,000A, although new fabrication techniques make narrower lines feasible. In fabricating cryotrons it is important that the edges of the gate elements be geometrically sharp to avoid undesirable switching characteristics associated with a thinner edge region, Fig. 2. One technique which has been used extensively to form patterns consists of placing a physical mask containing the film pattern between the evaporation source and the substrate and depositing through the mask. Film strips formed in this manner possess a penumbra at the film edges due to shadowing of the evapor-ant under the mask. Several techniques have been proposed for minimizing effects due to this penumbra. One of the more promising metallurgical techniques

Jan 1, 1967

By Jack L. Taylor

Single crystals of tungsten grown from powder -metallurgy swaged rod by high-temperative annealing were deformed in tetzsion at temperatures from 2500 to 5000 OF. Orientation of specittzen tensile axis, strained ratrix, and defortnation bands was determined optically by reflections from {110} etch pits. Slip traces meve analyzed and slip directiorz determined. Results indicate that {110}(111) , {112){111}. and {123}{111} type slip occur in tungsten over the terpe,atuve rutge investigated. Slip is orientation-dependent occuvring on tCuzt cowzbitzation oj slip plane and direction which has the highest critical resolved shear stvess. Overshooting appears to be a general occurrence between 2500' and 5000°F. Dejornatiotz bands show rotation in a directiorz opposite to the yotation of tire tensile axis. DEFORMATION in bcc metals has been reviewed by Maddin and Chen,' Keh and eissman,' and most recently by Nabarro, Basinski, and olt. From these reviews it is apparent that some disagreement exists concerning the crystallography of plastic deformation in bcc metals. There is evidence of noncrystallo-graphic slip, the crystal slipping on or near a noncrys-tallographic plane in the (111) zone for which the resolved shear stress is greatest. There is also evidence to indicate that crystallographic slip occurs in the planes of the same zone. On the other hand, there is agreement that the close-packed direction ( 111) is the slip direction in bcc metals. Further, in pure bcc metals4 and alloys the operative crystallographic slip systems are strongly dependent on temperature. Both crystallographic and noncrystallographic slip have been reportede8 in tungsten, a group VIA bcc metal. The number of slip families which operate in the case of crystallographic slip, however, has been in question. The earliest study by oucher' of single-crystal tungsten tested at temperatures of 1800 to 5000°F led to the conclusion that only {112)( 111) type slip operated. Raymond and eumann recently reached the same conclusion studying deformation by rolling of plasma-flame single crystals at 1800°F; however, only [loo] and [110] orientations were studied. Work at high temperatures by Leber and Pughs on tungsten and Chen and Maddin9 on molybdenum suggests that conjugate slip on nonparallel (110) planes may account for the slip on (112) and (123) planes found by others working with bcc metals. The present paper presents evidence of three families or modes of slip in tungsten in the temperature EXPERIMENTAL PROCEDURE Material. Standard microtensile specimens, 0.160 in. diam by 0.640 in. gage length, were ground from commercial powder-metallurgy swaged tungsten rod, type MK. Specimens were heated for 10 min at 5150°F or 6 hr at 5400°F in vacuum of 1 x 105 Torr or less to produce single crystals. At the lower temperature an average of two out of seven specimens heated in a group developed single crystals throughout the specimen length as shown in Fig. 1, the rest remaining wholly poly crystalline. At the higher temperature, three or four out of seven specimens became single crystal. Other than to note that Laue X-ray photographs generally showed sharp, well-defined spots, no attempt was made to assess crystal perfection or measure dislocation density. Two tungsten single crystals grown from the melt by the plasma-arc process were also used for this study.

Jan 1, 1967

By Keith G. Papke

Jan 1, 1985

By M. S. King

In the design of foundations for large structures and of safe mine openings in rock, the results of laboratory and small-scale in-situ tests are often used to predict the behavior of the material as a whole. For reasons of simplicity in these analyses, the rock is usually treated as an ideally elastic, isotropic material. It has been observed, however, that most rocks are neither isotropic nor ideally elastic. This observation is particularly true for rocks subjected to low confining pressures. It is therefore necessary to investigate further the effects of anisotropy and nonlinearity on the mechanical behavior of rocks. When small differences in stress and strain only are involved, the rock may be treated as an elastic material. The elastic constants for such a material subjected to a particular confining pressure can be calculated from the classical theory of elasticity for different degrees of anisotropy. There are two experimental methods by which this can be done: first, from measurements of static stress-strain relationships; second, from elastic wave velocities measured in the rock. The former yields the static elastic constants, and the latter, the dynamic constants. The static constants will be equal in magnitude to the corresponding dynamic constants only if the rock is ideally elastic. Walsh and Brace1 have reviewed theoretical studies of the elasticity of rock considered as a material containing pores and cracks. They re- ported that the presence of sharp, narrow cavities at low confining pressures strongly influences the mechanical properties of a rock. A considerable reduction in magnitude of elastic moduli is associated with the presence of inhomogeneities such as cracks or joints. The elastic properties appear to approach those of the uncracked material in magnitude as the cavities are closed by higher pressures. Walsh and Brace

Jan 1, 1970

By H. l. Burghoff, C. H. Mathewson

THE study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and 30 per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrystallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged. loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300º, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrystalline 70-30 brass. PREVIOUS WORK Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty & Moore.4 Results of the last-named investigation were published while the present work was in progress. Millers examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior, of iron crystals under static tensile loading at room temperature was reported by Gensamer and Mehl7 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of creep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature.

Jan 1, 1938