Search Documents

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By R. H. Kolb

A long term project at Shell Development Co.'s Exploration and Production Research Laboratory has been the improvement of the accuracy and the ease of BHP measurements. As a result of these efforts, two complete and separate systems have now been built for the automatic logging of BHP variations. The first of these is a small-diameter instrument suitable for running through production tubing on a single-conductor well cable. During the development of this instrument, as much emphasis was placed on providing a high degree of usable sensitivity and repeatable accuracy as on obtaining the advantages of surface recording. The second system combines the benefits of automatic, unattended recording with the convenience of a permanently installed Maihak BHP transmitter.' THE CABLE INSTRUMENT For many years the standard instrument for BHP determination has been the wireline-operated Amerada recording pressure gauge or one of several other similar devices. This gauge records on a small clock-driven chart carried within the instrument, and although relatively precise readings from the chart are possible, they are difficult to ob-tain. a Both the maximum recording time and the resolution of the time measurements are limited by chart size, and when a slow clock is required for long tests, the precision of the time measurement is often inadequate. Since it is impossible to determine the data being recorded until the gauge has been returned to the surface, wasted time often results when a test is protracted beyond the necessary time or when it is terminated too soon and must be re-run. Clock stoppage or other malfunctions which would be immediately apparent with surface recording remains undetected with down-hole recording; the test is continued for its full term with a consequent loss in production time. As new uses for subsurface pressure data evolved, the shortcomings of the wireline instrument became increasingly apparent, and the concurrent development of a surface-recording pressure gauge and the associated high-pressure well cable service unit' was undertaken. Description of the Instrument Because of its ready availability and advanced degree of development, the Amerada bourdon-tube element was chosen as the basic pressure-sensing device. This element converts a given pressure into a proportional angular displacement of its output shaft, and a suitable telemetering system was designed to measure accurately the extent of this displacement and to transmit the measurement to the surface and record it. The telemetering system furnishes a digital record printed on paper tape by an adding machine-type printer. The present arrangement provides a resolution of one part in 42,000 over the angular equivalent of full-scale deflection, giving a usable sensitivity of better than 0.0025 per cent of full scale. An additional refinement simultaneously records on the tape the time or the depth of the measurement, also in digital form. When the instrument is placed in operation, an adjustable programer can be set to initiate a read-out cycle automatically at selected time intervals. When subsurface pressures are changing rapidly, readings may be recorded as frequently as once every 10 seconds; when pressures are more nearly stabilized, the period between readings may be extended to as much as 30 minutes. Because the instrument is surface-powered as well as surface-recording, the maximum period of continuous logging is (for all prac. tical purposes) unlimited. The subsurface instrument is a tubular tool, 1 1/4-in. in diameter and 6.5 ft in length, operating on 12,000 ft of conventional 3/16-in. IHO logging cable. The transmitting section, mounted above the bourdon-tube element in place of the regular recording mechanism, contains no fragile vacuum tubes or temperature-sensitive transistors. This unit has been laboratory-tested to 1 0,000 psi and 300°F and has performed dependably during a number of field operations. The down-hole transmitting arrangement can be fitted to any standard Amerada pressure element, regardless of range and with no modification of the element itself. Calibration To obtain a repeatability commensurate with the sensitivity and resolution of the instrument, it was necessary to develop a special calibrating technique. The manufacturers of the Amerada recording pressure gauge claim an accuracy of only 0.25 per cent of full scale, which is a realistic figure for normal calibrating and operating procedures. An exhaustive investigation was made of the errors inherent in the bourdon-tube element, itself, independent

By K. C. Gilbart, Edgar Stansfield

One of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal,

Jan 1, 1932

By C. A. Czako

INTRODUCTION In recent decades sintering and pelletizing of finely divided materials have become the primary tonnage producing modes of agglomeration. This statement is especially true in the iron and steel industry and, to a lesser degree, in the nonferrous, chemical and non-metallic minerals processing industries. In every industry the main objectives in agglomerating fines are essentially the same, namely to convert ores, minerals and chemicals of undesirable fineness into agglomerates characterized by a size consistency desirable for subsequent use or processing. Depending on the type of agglomeration process selected and the conditions maintained during agglomeration, the physical process of increasing size is complemented by a number of other unit processes. These processes can occur simultaneously, consecutively or in an overlapping manner. Some of these additional unit processes are incidental to the agglomeration operation, but at the same time can be critical, depending upon the subsequent use of the product. Accordingly, during processing, conditions have to be controlled to either suppress or enhance the extent of completion of these unit processes. The purpose of this report is to review laboratory testing as the basis for engineering modern sintering and pelletizing plants. Considering that most typical applications are for the iron and steel industry, agglomeration of ferrous materials is reviewed and discussed. When these total processes are adapted to suit non- ferrous materials, chemicals, or non-metallic substances, the over- all approach remains the same; only the processing parameters are affected as necessitated by the different nature of the materials.

Jan 1, 1977

By Arthur B. Yates

DIAMOND drilling has advanced and expanded during the past few years. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. CONTROL A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing-even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved, however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the nearer the direction of the hole is to this ideal, the straighter it will remain. This, of course, is not always practical and in some cases is impossible. Usually such a

Jan 1, 1946

By Wilber Stout

In Ohio, the annual output of coke made from native coals has averaged not more than 70,000 tons, or about enough to run a 200-ton blast furnace. Raw coal locally mined from the Sharon, or No. 1, bed was used for iron smelting in Mahoning furnace at Lowellville, Mahoning Co., as early as 1846. This practice was continued in the Youngstown district until the coal became scarce and the Connellsville coke more popular. At present, the Sharon bed contributes a part of the fuel for the production of ferrosilicon iron at Jackson, Jackson CO. About one-third native coal and two-thirds soft coal are used. In this state, coke, on a commercial basis, was first made in Jefferson County probably about 1861 or 1862. The coals used were the Steuben-ville Shaft, or Lower Freeport, and the Strip Vein or Middle Kittanning. The practice, however, was discontinued before 1880 because of the competition of superior foreign cokes. Beehive ovens, later built at Leetonia, Columbiana Co., were operated for only a few years; the coal used at this place is the Lower Kittanning or No. 5. In a desultory way, slack from the Pittsburgh coal has been coked at a few places in eastern Ohio, and attempts, either for experimental or for commercial purposes, have been made in other parts of the state. Small quantities of coke were made from the Upper Freeport coal at Salineville, Columbiana Co., and near Nelsonville, Hocking Co.; the results were poor. Tests were made of the Middle Kittanning coal near Zanesville, Muskingum Co., at Moxahala Furnace, Perry Co., and at Washington Furnace, Lawrence Co.; the cokes were all high in sulfur and ash. Attempts were made to coke the Clarion coal at Vinton Furnace, Vinton Co.; a small battery of molding ovens and a pile of high-sulfur coke yet remain to tell the story. The Pittsburgh coal was coked on a commercial scale at Utley and at Lathrop, Athens Co., but the operations were not successful and were soon abandoned. These failures and indifferent successes are not to be attributed to a lack of demand for a first-class coke, as Ohio has held a commanding place for many years in iron smelting; nor to a deficiency of coals, as the state has a vast reserve of such material. They are to be ascribed to the inferior quality of the native products offered to the trade. The cokes

Jan 1, 1920

By Chester R. McKee, Robert W. Terhune, Merle E. Hanson

The relationships describing the enhancement of permeability by firing explosives in boreholes have been derived and combined to yield permeability enhancement as, [ ] or the case in which the stress decays asymptotically as a power law kc and nc represent permeability and fracture density at the edge of the pulverized region near the cavity wall, f is a geometric attenuation factor, m is the dissipation due to real material effects, ko is the original permeability and rd is the scaled radius. This relationship has been compared with available measurements from the American nuclear shot "Hardhat", the French nuclear events in Hoggar granite and the chemical explosive shot in coal near Kemmerer, Wyoming. Significant correlation between this theory and the experimental measurement is observed. A comparison between single and multiple detonations shows that permeability enhancement falls off steeply near the shot; however enhancement can be considerable midway between two shots spaced 10 cavity radii apart. The degree to which enhancement, can be significant depends on material properties and fracture density. Porosity distribution from the explosive 1s the dominate parameter in permeability enhancement. Existing theories of permeability enhancement have also been reviewed.

Jan 1, 1976

By H. D. Outmans

Present first-order theory for frontal stability and viscous fingering of immiscible liquids is improved by including the nonlinear terms in the equations describing conditions at the interface of the liquids. This leads to the revision of several conclusions which were based on first-order theory. They concern the growth rate and changing shape of a sinusoidal disturbance, particularly in relation to the wave number of this disturbance. Nonlinear aspects of effective interfacial tension are discussed and it is shown that this tension is not simply a positive proportionality constant in a linear relation between pressure difference and curvature at the interface. Scaling requirements are determined from the dimensionless groups which govern fingering. Gravity and interfacial tension invalidate a previously formulated conclusion that the shape of a finger after a given displacement is independent of the displacement velocity. Also, similarity of fingering (and, hence, of sweep efficiency in case of an unstable front) requires geometrical similarity of the initial disturbance in the model and the reservoir with a scale factor which is the same as the one for scaling down the dimensions of the reservoir. INTRODUCTION The critical velocity at which the transition zone in the vertical displacement of immiscible liquids becomes unstable was calculated by ill. More recently, the same was done for nonvertical displacements and it was also shown that the stability is affected by an effective interfacial tension between the liquids. 2-4 Although in the oil reservoir a stable front is always desirable from a recovery point of view, the necessary velocity may have to be so low that the corresponding production rate is not economical. In that case, a knowledge of the fingering unstable front is necessary for predicting recovery at break- through. Studies in this direction have not gone beyond the very moment at which fingering first occurs.5,6 Conclusions about stability and fingering in these references are all based on linear theory. In this theory the nonlinear terms in the equations describing conditions at the front are neglected. The usual justification for this lack of mathematical rigor is that the nonlinear terms can be made small relative to the linear terms and, supposedly, small causes produce only small effects. It has been recognized, however, that this is not necessarily true in the nonlinear problems of hydrodynamics.7 The hydro-dynamic stability and fingering of the front between two liquids, accelerated in a direction normal to the front, for instance, is strongly influenced by the nonlinearity of the boundary conditions.8-10 Since these boundary conditions are not unlike those arising in the problem of stability and fingering of the front during a slow immiscible displacement in porous media, it was thought that there, too, the nonlinear terms should be taken into consideration. A summary of the results obtained in linear theory and a comparison with experimental data precede the nonlinear theory developed in this paper. This summary serves to introduce some quantities which will be used in the further develop ment. It should also be pointed out that the method of higher-order approximation by which the nonlinear stability problem is solved has application in other reservoir studies.11 SUMMARY OF LINEAR THEORY 1. A plane interface remains stable if its velocity is smaller than a critical velocity. vc = (p2-p1)gn/(l/A2- l/A1 .........(1.1) This equation is derived for uniform flow in a thin layer inclined to the horizontal plane. The displacement takes place in a direction normal to the intersection of this layer and the horizontal plane. The undisturbed (line) interface is normal to the velocity. Fluid 1, the upper fluid (gas), is displacing Fluid 2 (oil). (VcQS would be the injection rate in cc/

By Mark R. Lamb

The treatment of slime is of special interest to those engaged in cyaniding gold- and silver-ores. The usual practice is to make as small a percentage of slime as possible. In many instances the slime is given no treatment, but is impounded in dams in the hope that the future will develop some method of economically treating this product. The filter-press was the first step upward from ordinary decantation, but, on account of heavy labor-charge and high cost, its use has been limited to high-grade material. The slime at the Combination mill at Goldfield averages perhaps $20 per ton, and although the values are quickly dis solved the filter-press installation was not entirely satisfactory, resulting in the erection of the canvas-cell filter, developed by Chas. Butters and his staff. This filter is a great improvement over the filter-press, and the following description of it will be of interest to those engaged in treating slime produced in crushing ores, especially in view of the fact that, by the use of this filter, slime can be treated at a lesser cost and with a higher percentage of gold- or silver-extraction than in the ordinary treatment of sand; and, moreover, the initial outlay for an all-sliming plant is less than that for the ordinary sand- and slime-plant. The economy of construction of the Butters filter-plant is clearly shown in Figs. 1 and 2, which illustrate the 20-frame filter of 40 tons capacity, now being installed by the Nevada Goldfield Reduction Co. In this construction the slime-pump is so connected that it call pump to or from either tank or the filter by changing the valve-settinga—a combination which is necessary in this particular installation, since sufficient fall is not available for filling and discharging the filter by gravity. Ordinarily, a slime-plant comprises: a filter-box with frames

Jan 1, 1908

By H. J. Freyn

The American iron and settl manufacturer finds himself to-day barely at the threshold of enormous possibilities for practicing rational economy in the use of fuels.

Jan 1, 1915

By Sydney H. Ball

MINERALS used primarily for personal adornment and decorative purposes are called precious stones. To be so prized, the stones must possess beauty of color, must not be too common, and must be hard enough to withstand ordinary wear. If transparent, they must have brilliancy and fire. Almost one hundred minerals have been used as precious stones, the noble gems being the diamond, emerald, ruby, and sapphire; pearls are frequently included by courtesy. These gem stones, however, are sometimes equaled in beauty by fine opals, aquamarines, ourmalines, spinels, chrysoberyls (both cat's-eye and alexandrite), and spodumenes (hiddenite and kunzite). The Greeks, Romans, and medieval Europeans grouped together gem stones according to color and degree of transparency, and only as the niceties of mineralogy began to be known, about a century ago, was it realized how many different minerals have the beauty required of gem stones. Pliny, for example, did not distinguish between rubies and the red varieties of spinel and garnet, although he conjectured that the beryl and emerald were one mineral. GENERAL SURVEY Early man treasured bright colored berries, attractive shells, white teeth of wild animals and brightly colored pebbles, and used them as personal ornaments. In the eastern hemisphere, the earliest stones used were members of the quartz family (100,000 to 75,000 B.C.); then obsidian and amber (50,000 to 25,000 B.C.); the jade minerals, fluorspar and jet (22,000 to 7000 B.C.); turquoise (7000 to 3400 B.C.); lapis lazuli and garnet (prior to 3500 B.C.) ; emerald (2000 to 1800 B.C.) ; sapphire, ruby and diamond (800 to 500 B.C.). Indeed, gem mining is the oldest form of mining, and before any metals were known primitive man recognized about 18 gems and decorative stones. At first he sought them in stream gravels and residual deposits but by 3400 B.C. the turquoise mines of the Sinai Peninsula were operated. This was the world's first important hard-rock mining enterprise. The Afghanistan lapis lazuli mines may

Jan 1, 1949

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-

By A. T. Shurick

TILE present economic crisis in bituminous coal is substantially the most insidious, and critical, in the modern history of the industry. The large consumption deficit that has gradually developed (almost unawares), has culminated in a situation that has forced home the urgent necessity for prompt and radical remedial measures, such as the various mergers now in course of negotiation. Conditions today are sufficiently comparable with those in the iron and steel industry, preceding the formation of the United States Steel Corpn., to suggest the possibility of a sweeping super-consolidation, that all but staggers the imagination. The important function of the banker in this, and lesser projects, is too well known to require comment, and it is important that we understand clearly just what these functions are. Certain features in banking practice came up for consideration in connection with a rather exhaustive economic study into the prospective future of the coal industry, upon which I was recently engaged for an Eastern bituminous interest. This survey was made for the purpose of effecting a decision on certain pressing questions of policy, involving considerable capital expenditures, that would be compatible with the flattening out in the curve of production in recent years. An examination of the TRANSACTIONS, and the coal literature generally, failed to disclose any pertinent, and authoritative data, on this subject. This was more or less characteristic of the whole survey, which had involved a large amount of original research, and measures were taken to procure the required information. The following notes have been compiled largely from the data thus collected, supplemented with material, suggestions and criticisms, by several of the larger banking houses active in coal, together with personal memoranda of my own.

Jan 1, 1928

By R. F. Decker, J. R. Mihalisin

Phase transformations in a series of relatively pure nickel-titanium-aluminum binary and ternary alloys were studied. The purpose was to clarify age-hardening mechanisms, especially in predominantly titanium-hardened compositions. The micro-structures, as determined on a tirne-temperature-transformation basis by light and electron microscopy and X-ray diffraction, were correlated with room temperature and hot hardnesses. The stability of the ? phase under nonequilibrium conditions was shown to be important in this system. MANY of the alloys designed for service in the temperature range of 1200oF (649°C) to 1800°F (980°C) are austenitic iron-.nickel base alloys hardened by titanium and aluminum. The control of high-temperature properties of these alloys has been advanced by the knowledge of microstructures provided by the equilibrium diagrams of Taylor and Floyd1 and Taylor.2, 3 However, there have been notable instances in the predominantly titanium-hardened alloys where the correlation of properties with microstructure and the equilibrium diagrams has been unsuccessful. Mihalisin and carrol14 have noted in electron microscope studies of commercial alloys of this type that a fee phase precipitates and transforms to 71 (hep Ni3Ti) in stress-rupture tests. Bieber5 found that this fee phase remained in nickel-chromium-titanium alloys even when aluminum was excluded. Age hardening in iron-nickel base alloys has been attributed to 71 by Craver, Aggen, and Dyrkacz,6 ? (fee phase based on Ni3Al) by Beattie and Hagel7 and both phases by Lena,8 Yet, on the basis of the nickel-titanium-aluminum equilibrium diagram of Taylor and Floyd shown in Fig. 1, it has been difficult to understand the presence of ? in low aluminum alloys. Furthermore, the characteristic coarse dispersion of 71 has not been commensurate with the marked aging response. Also there have been anomalous grain boundary transformations in the iron-nickel base alloys which have markedly reduced notched stress rupture properties.9 These have been related to boron content and residual cold work. Recently, Golubtsova and Mashkovich,10 Buckle and Manene11 and Bogaryatskii and Tyapkin12 have noted a transition fee Ni3Ti in titanium-hardened nickel-base alloys. It was apparent from the latter studies that a transition phase was important in the nickel-titanium-aluminum system. The purpose of this study was to identify this phase, measure its transformation characteristics and kinetics, and attempt to correlate these findings with age hardening. It was believed that time-temperature-transformation studies, because of their adaptability to transition phases, would be of most value for this investigation. Accordingly, this method of study was undertaken on relatively pure nickel-titanium-aluminum alloys with controlled variations in boron content and residual cold work. EXPERIMENTAL PROCEDURES Compositions were selected from the nickel-titanium-aluminum isothermal section of Taylor and Floyd.' These compositions are plotted in Fig. 1 and were selected to obtain equal aging potential of approximately 15 pet by volume of the equilibrium precipitate. The materials were vacuum melted from

Jan 1, 1961

By E. C. Houston

THE presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximately 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A 7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;" in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. DESCRIPTION OF PROCESS Metallic magnesium is produced electrolytically by the Dow and the Elektron

Jan 1, 1945

LANS are underway for the annual meeting of AIME, to be held in New York, February 17 to 21. The technical program includes meetings of all divisions of all three branches, Mining, Metals, and Petroleum. The bulk of the technical sessions will be held at the Statler Hotel, and the annual banquet will be held at the Waldorf-Astoria, Wednesday evening, February 20. The technical program of the Mining Branch activities is included in this issue. While it is not complete in every detail, it shows general interest groupings as well as subjects to be discussed. The program for each division is shown separately to facilitate following the activities of these special interest groups. Then, after a full scale and possibly somewhat strenuous technical meeting, a post-meeting feature will appeal to many of the members. A restful cruise to Bermuda and Nassau is offered at special rates to AIME members and friends. The schedule is a 3:00 pm departure from New York on the Queen of Bermuda on Saturday, February 23; arrival at Bermuda at 7:00 am Monday, February 25; arrival at Nassau at noon, Wednesday, February 27; and the trip ending again in New York at 9:00 am, Saturday, March 1. Rates begin at $202.10 per person, with higher rates depending upon accomodations desired. The base rate includes outside room with private bath and all meals, as well as Federal, Bermuda and Nassau taxes. Reservations for the trip should be made immediately through Leon V. Arnold, 36 Washington Square West, New York 11, who is in charge of arrangements.

Jan 1, 1952

By Irwin Roman

PART I. INTRODUCTION THE literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years, but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data .2 There seems to be a general reluctance among geologists and. engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1931

By F. Lynwood Garrison

The enormous growth of the manufacture of Bessemer steel in this country within the last few years, due to the almost constant large demand for steel rails, renders it very desirable that our knowledge of the physical and chemical properties of a material upon which we place so much dependence should be increaqed by every possible means. It was with this end in view, and also in hopes of learning something of the causes affecting the regularity of the Bessemer product, that I took up the subject of this paper a short time ago. The lise of the microscope as an instrument of research in the metallurgy of iron and steel is now fairly well established;

Jan 1, 1887

By J. H. Brophy

Experimental evidence in recent years shows that nickel coated hydrogen reduced tungsten powder can be sintered to 98 pct of theoretical density at 1100°C. New data indicate that the sintering rate is the same for nickel contents ranging from 0.125 wt pct (mon-atomic layer) to 5.0 wt pct Ni coated on 0.561. tungsten powder. Nickel tungsten made by coreduction from oxides sinters in a kinetically similar way, but the rate tends to increase with higher nickel contents. The activation of sintering can be accomplished with a minimum amount of nickel if coated powder is used. Transverse rmpture strength was found to increase in specimens containing 0.25 pct Ni as density increased during the initial stage of the carrier-phase sintering process. Upon the onset of grain growth in the final stage, strength was found to decrease. With increasing nickel contents up to 4 pct, strength increased. Maximum strengths in three-point loading were observed at 73,000 psi for 0.25 pct Ni and 93,000 psi for 5 pct Ni. These were comparable to that of massive tungsten recrystal-lized in the presence of nickel and tested in the same way. The results were sensitive to the mode of powder treatment and ductility was negligible in all cases. The study and application of sintered bodies of nickel and tungsten is not new; however, the analysis of the mechanism by which small additions of nickel increase the sintering rate of tungsten promises to Contribute new information regarding sintering theory in general. Initial experimental evidence was presented by the authors showing that nickel-coated hydrogen-reduced tungsten powder may be sintered to 98 pct of theoretical density at 1100°C in 16 hr.' Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the 'solution-precipitationo step postulated when the carrier phase is liquid3 although in the nickel tungsten case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in mi-crostructures at the temperatures under consideration. In the present work, new data for nickel-coated tungsten powder are offered in support of the proposed mechanism, and a more explicit study of the second stage of densification is presented. Concurrently, the sintering kinetics of these coated powders are compared to Ni-W powder made by coreduction of oxides. In this way the present work can be compared to earlier results in nickel activated sintering of tungsten in which the coreduction process was emplyed. The ultimate utility of such an activated sintering process will be determined to some extent by the mechanical and physical properties of the final prod-

Jan 1, 1962