Search Documents

By B. N. Das, P. A. Beck

THE o phases have a complex tetragonal structure with Lo/ao = 0.52 and 30 atoms per unit cell.1 A large number of such phases are now known to occur in various binary systems of the transition elements and they exhibit the following typical features: 2,3 The composition of binary o phases is variable, ranging from approximately A4B to ABI. With only a few exceptions, in the o phases the A-ele-ment comes from the V- or Cr- group of the periodic table, while the B-elements are from the Mn-, Fe-, Co-, or Ni- group. In the first long period the corresponding o phases of the V- and Cr-series have approximately the same compositions. However, as the B-element changes from Mn to Fe to Co to Ni, the mean composition shifts monotonously toward higher A-contents.2-4 For example, if the mean compositions of the various o phases with vanadium are compared with each other, the composition shift mentioned above becomes plainly visible: V 30Mn0 80 Vo.45Feo..,, Vo .,Coo. 45 and Vo.5Nio.3. Similiar composition shifts, although not the same composition values, were observed in u phases formed by second and by third long-period transition elements.3'4 This behavior, very characteristic of o phases, is in rather sharp contrast to the usually quite well-behaved stoichi-ometry of the Laves phases. In the latter, the AB2 stoichiometry predominates, with A the large atom and B the small atom.= The p phase occurs in the four binary systems of Mo or W with Fe or Co. On the basis of their crystal structure determination, Arnfelt and westgren6 ascribed to the p phase in the Co-W system the ideal composition W,Co7. Since all four binary pphases have nearly the same composition, it would seem quite plausible that some definite stoichiometry such as A6B7, might be characteristic of this phase, as AB2 is of the Laves phases. On the other hand, it has been noted,7 that the phases occur at average electron concentrations near to those at which the various cr phases are found. Also, it has been pointed out by Shoemaker and associates8 that structurally the a phases and the p phases are somewhat related to each other; both of these structures may be described in terms of suitable stackings of quasi-hexagonal layers'of atoms. By studying a suitably chosen ter- nary phase diagram, one might expect to be able to find out which one of the two conditions, the analogy with the o phase or the constant ratio between the number of large atoms and the number of small atoms in effect governs the behavior of the p phase. Several isothermal sections of ternary systems containing o phases have been investigated. In all cases where two binary o phases occur, these were found to be connected b a more or less straight ternary o phase field.7' '10 Such elongated o phase fields were also found in ternary systems in which only one of the limiting binaries is known to contain o phase. In this manner a latent o forming tendency could be detected and the virtual composition of a "binary o phase", which does not actually occur as such was approximately determined by extrapolation. The behavior of the phases, including their composition shift, is analogous to that of the classical electron compounds, as described by Hume-Rothery.11 In order to decide whether the p phase is essentially a "size compound" like the Laves phases, where a fixed stoichiometric ratio is quite generally maintained between the "large atoms" and the "small atoms", or whether the p phase is typically an "electron compound" in the same sense as ois, it was decided to investigate an isothermal section of the Mo-Mn-Co system. The Mo-Co system12 and the Mo-Mn system13 each are known to have a binary o phase. It could be therefore expected that a ternary o phase field will connect these two binary cr-phase fields. The p phase is known to occur in the Mo-Co system. If the p phase should turn out to form an elongated phase field extending deep into the ternary system, the following considerations mighto apply. The atomic radius of manganese (1.314for C.N.12) is between the va,lues for Mo (1.40Afor C.N.12) and for Co (1.26Afor C.N.12). If it is assumed that p is a "size compound", and that Mn is substituting for the smaller Co atoms in the p-structure in the ternary system, the y-phase field might be expected to extend parallel to the Mn-Co binary line. If Mn is substituting for the large Mo atoms in the p-structure, the p-phase field may be expected to extend parallel to the Mn-Mo binary line. On the other hand, if the p-phase turns out to be an "electron compound" like o, the ternary p-phase field should extend parallel to the ternary o -phase field connecting (Mo,Mn)owith (Mo, Co) a

Jan 1, 1961

By AIME AIME

A. A. Holland, Consulting Engineer, Toronto, Ont.-I noticed in this discussion of locations in which radium is found, no mention is made of the recent deposits discovered in Ontario. While radium is not a subject with which I am very familiar, I took an interest in this deposit on account of its novel occurrence. It is found in Haliburton County, near Wilberforce, Ontario, associated with a quartz free pegmatite, in a "break" that I understand can be traced for two miles. This "break" marks the contact between the limestone and syenite and contains numerous cavities or vugs. The gangue, on account of its deep purple, appears to :be amethyst.

Jan 1, 1930

By R. S. Archibald, L. S. Chabot

The Blueberry mine is about 10 miles west of Ishpeming, Marquette County, Michigan. The property consists of about 2000 acres in sees. 3, 4 and 5, T. 47, N.R. 28W. and secs. 32, 33 and 34, T. 48, N.R. 28W., and, excepting one intervening 80-acre tract, contains the iron formation for a length of about 21/4 miles. The property is traversed by State Highway M-28 and is served by three railways, the Chicago & Northwestern, the Duluth, South Shore & Atlantic, and the Lake Superior & Ishpeming. The Northwestern transports the ore to a dock at Escanaba; the other railways, to Marquette. Ore for Chicago goes via Escanaba and that for Lower Lake ports, as Detroit, Cleveland, and Buffalo, via Marquette. History The presence of iron formation in this property has been known for many years, and mining operations on a small scale have been carried on intermittently. The Dexter mine, on the SE.1/4 of the NW.1/4 of sec. 3, was worked from 1883 to 1897 and 118,000 tons of ore was mined. From 1907 to 1915 extensive exploration was carried on over the whole of sec. 3, including 79 diamond-drill holes with a total footage of 26,000 ft. The Chase mine, on the NE.1/4 of the NE.1/4 of sec. 3, was developed from this exploration work, but after about 200,000 tons had been mined the property was abandoned. From 1908 to 1910 exploration was carried on by another company on sec. 4, 47-28, including four drill holes with a total footage of about 5000 ft. Much of the drilling on sec. 3 and of the exploration work on sec. 4 are within the present developed area of the Blueberry mine. A general campaign of diamond-drill exploration was undertaken in 1924, and within a year a considerable amount of ore was developed. The Ford Motor Co. then took an option on the property and carried on check drilling and diamond-drill work until the spring of 1926, when enough ore had been developed to warrant the sinking of a shaft

Jan 1, 1937

By N. Brown

From the theories of flow and fracture it is shown that the difference in reciprocals of the transition temperatures (OK) is a quantitative measure of temper ernbrittlement. Experimental data are given which support this conclusion. STUDIES of temper embrittlement have been made with various viewpoints; some involved a study of the kinetics of the reaction,',2'" others were concerned with changes in the mechanical properties," . and still others investigated the structural differences between the embrittled and unembrittled states by means of the microscope," -ray ,' measurements of electrode potential," and electrical resistivity." In all these studies, the difference in impact properties was the criterion for distinguishing between the embrittled and unembrittled states. By common agreement the difference in transition temperatures is now taken as a measure of the degree of embrittlement, and this measure is used as the quantitative measure upon which studies of the phenomenon are based. Vidal and Jolivet"' suggested that the degree of embrittlement was the same whether measured by impact or by a slow bend test. Their conclusion was based on tests at constant temperature. Jaffe and Buffum" using the impact and slow bend test showed that, for a given degree of embrittlement, the difference in transition temperatures varied with the method of testing. Hultgren and Chang" showed that the difference in transition temperature produced by the V-notched Charpy impact test was not the same as the value produced by the keyhole-notched impact test. This is a very fundamental point because there can be no true measure of temper embrittlement unless it is invariant with respect to the test method. Theory The purpose of this analysis is to show how the transition temperature depends on the stress distribution and the state of the material. The criterion for fracture may be stated as follws: where iF is some function of the principle stresses and F is a critical condition depending on the state of the metal. Similarly yielding occurs when Where is another function of the prin-ciple stresses and Y is a critical value depending on the state of the material. There is some controversy as to the exact form of the function f,.(u,, u,, us) but most experimental data give the following criterion:= where 8, and 6, = 21 or 0. Combinations of 6, and 8, give the various criteria such as the normal stress, the hydrostatic tension, and the maximum shear stress laws. Agreement is general that the octahedral shear stress law adequately describes the yield condition. where the bracketed factor will be called the design factor and depends on the stress distribution. Whether the metal decides to yield or fracture is given by the condition that The effect of temperature and strain rate upon Y has been studied by various investigators, It has been shown by MacGregor and Fisher" that

Jan 1, 1955

By John Ward Smith

Dawsonite-bearing oil shale of Colorado's Green River formation offers a unique and vast (more than 5.9 Gt of A120 j) resource of easily extractable alumina. The processing methods required by the thermal reactions of dawsonite and its oil-shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary federal oil-shale withdrawal appear less solvable.

Jan 1, 1982

By L. L. Wyman

THE exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics, 1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors" wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickel-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-1 per degree Centi-grade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working can cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carbon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys.

Jan 1, 1939

By T. E. Watkins, M. D. Nelson

A method of determining the lime content of drilling muds proposed by Battle and Chaney* has been examined both in the Field Research Laboratories of Magnolia Petroleum Co. and in field drilling operations. This proposed analytical method is condensed as follows: Titrate one ml of mud and one ml of mud filtrate, each with 0.02 N H2SO4, to the end point with phenolphthalein. The volume of acid in ml required for the mud titration is recorded as Pm and that of the mud filtrate titration as Pf Calculation of the lb lime/bbl mud is accomplished by use of the formula, lb lime/bbl mud = 0.6 (Pm - 1.3Pf) - 0.6 The analytical procedure outlined by Battle and Chaney was found to be quite satisfactory when reasonable precautions are used in mud sampling technique. Calculation of lime concentration by the method proposed in the above publication, however, has given values that varied as much as 100 per cent from the known lime content, for muds of either high or low solids concentration. By use of a formula, lb lime/bbl mud = 0.26 (Pm-F1.Pf), based on chemical equivalents of acid required for titration, both laboratory and field data have been satisfactorily correlated with the known amounts of lime present in the muds. In this formula a correction, F1, or volume fraction of liquid in the mud, is made for the solid content of the mud. Pm and Pf * Paper on "Lime Base Muds," presented by J. L. Battle (Humble Oil and Refining Co., Houston, Tex., and P. E. Chaney (Sun Oil Co., Beaumont Tex.), at the 1949 Spring Meeting of the Southwestern District API Division of Production, Dallas, Tex. The analytical procedure has also had wide distribution in a trade journal, Kembreak, published by the Accuracy Rig and Tool Co., Houston, Tex, †Derivation of equation lb/bbl — grams/350 ml 1 ml 0,02 N acid = 0.000741 grams of lime 1 ml 0.02 N acid/ml lime suspension = 0.26 lb of lime bbl lb of lime/bbl = 0.26 (Pm -F1, Pf ) have the same significance as in the Battle and Chaney equation. Table I shows typical data employing both formulas in calculating the lime content of various lime muds. This suggested procedure ignores lime which is in solution in the mud. The solubility of lime in water, normally about 0.5 lb per bbl, is greatly decreased by the addition of caustic soda, and, in a lime mud, it is probable that the concentration of dissolved lime is of the order of 0.1 lb per bbl. Such an amount of lime can be ignored, since it is within the range of accuracy of the method.

Jan 1, 1950

COUNCIL OF ECONOMICS, AIME Formerly Mineral Economics Division Established as a Division December 15, 1948 Established as a Council February 26, 1957 Sheldon P Wimpfen, Chairman John D Ridge, Vice-Chairman (Mining) A J Philips, Vice-Chairman (Metals) Warren B Davis, Vice-Chairman (Petroleum) COUNCIL OF EDUCATION, AIME Formerly Mineral Industry Education Division Established as a Division January 15, 1932 Established as a Council February 26, 1957 James D Forrester, Chairman Charles V Kirkpatrick, Vice Chairman (and Chairman-elect) Lysle E Shaffer, Past Chairman Truman H Kuhn, Secretary-Treasurer Colorado School of Mines Golden, Colorado John S Bell, Contact AIME Director

Jan 1, 1960

By A. S. Eve

In the spring of 1930, the question was raised as to the possibility of estimating the depth to which the pyrrhotite-nickel deposit at the Falconbridge mine extended in the earth. This body is 7500 ft. long, it dips at 80° to the north, and it is fairly straight with slight sinuosities. Dr. F. W. Lee suggested that it might be possible to solve the problem by measuring the vertical magnetic intensity, with a good magnetometer, both near the surface of the earth and also at a level a few feet higher in the air. The writer regarded this suggestion with some scepticism, but it was decided to put the scheme to a practical test. In July, 1930, Dr. Lee, Dr. Keys and the writer, with Mr. Joyce and Mr. Belloc as assistants, made a firm, light wooden platform (Fig. 1) measuring 4 by 4 ft. on the top, which was 10 ft. above ground. This platform could be moved easily a few yards by four men, and carried across country in a wagon or by motor truck. Some iron nails were used in its construction, but we were not able to detect their influence on the Askania magnetometer. Nevertheless, in future work, the use of iron should be completely avoided. Readings were taken along a traverse at right angles to the orebody, at several stations, both on the ground and on the platform. The excess readings, over the dike, as compared with those about 800 ft. away, are shown in Table 1. The largest reading, 6.8, is open to suspicion and should be rejected. The depth of the top of the orebody is known by electrical survey, and by actual drilling, to be about 112 to 123 ft., and the covering is sandy glacial drift. Similar readings were taken over a long straight magnetic diabase dike. These also are shown in Table 1. The magnetic vertical intensity is consistently less at the higher level, which is 10 ft. above the lower level.

Jan 1, 1932

By Robert F. Mehl

THE gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transforma-tion rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data, on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2 since then several important papers have appeared. Our present, knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-cen-tered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-Centered alpha lattices in tampered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: { 111 }Y//{110}a [110]Y//[111]a

Jan 1, 1937

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

By Clyde E. Williams

DESPITE the confusion resulting from the depression and the beginnings of recovery, important progress in all branches of iron and steel metallurgy has been accomplished during the year 1933. Research work has been intensive and highly technical, with increasing attention paid to fundamentals. Plant application of research developments has been rapid. Highly specialized laboratory methods were used for the study of iron-ore concentration methods. More attention has been given by the blast-furnace operator to the sizing of ore and the elimination of fines from the charge by the use of sinter. Combustion in the open-hearth has been placed under better control and the insulation of open-hearth furnaces has spread rapidly, with resultant higher fuel efficiency and better control of the melting and refining operations. Control of iron oxide content in the slag and the determination of iron oxide and other inclusions in steel received great attention during the year.

Jan 1, 1934

By Finlay, J. S.

THE North Lily Mine started its career in an unusual way it was discovered by a geologist. The remarkable circumstance of driving a 2400-ft. drift into an unexplored country and "hitting her on the nose," indicates that geologists are sometimes numbered among those whom the Lord loves. Diamond- drilling from surface had previously shown the presence and position of the Ophir beds, and surface showings of pebble-dykes, faults, and bleached rhyolite indicated conditions similar to those at the Tintic Standard "Pot-hole." The discovery drift from the Tintic Stand- ard 700-level reached the North Lily orebody in January, 1926, and development and stoping were continued by Tintic Standard men and equipment until the North Lily shaft was sunk and put into service in May, 1928. The discovery drift was run on a cooperative basis by the Tintic Standard and North Lily mining com- panies. Finding the North Lily mine cost the North Lily company $26,000. The Tintic Standard Mining Co. furnished men and equipment to drive this discovery drift at a fraction of what it would have cost to find the orebody from surface. This was the beginning of the friendly cooperation that still exists. Through Tintic Standard ground the Tintic Standard paid two- thirds of the cost and the North Lily one-third; the cost of the drift through Eureka Lily, into North Lily ground, was paid by North Lily. Later, another drift from the Tintic Standard 900-level was run on the same plan, excepting that Eureka Lily paid its share of the cost; that is, the Eureka Lily paid one-third of the expense in Tintic Standard ground, and the Eureka Lily two-thirds and North Lily one-third in Eureka Lily ground. This 900-drift was driven by North Lily from the Eureka Lily line to near the North Lily west side-line. From this point the Chief Consolidated continued the drift well into Tintic Bullion ground.

Jan 1, 1929

By Henry D. Hibbard

I. INTRODUCTION. THESE impurities are perhaps the most important things in steel-especially steel made by the oxidation processes-the effect of which has not been at least approximately determined. By oxidation processes I mean the Bessemer and Siemens-Martin, during which the metalloids in the charge are removed by oxidation. It has been truly said that it is a clear advantage to have a new name for a new thing. To secure this and to economize space, let us adopt the name sonim (plural sonims) to designate the solid non-metallic impurities existing in steel or other metal. I would define a sonim as a solid non-metallic portion of matter existing as an impurity in metal. A piece of sand, brick, clay, or such material, imbedded in metal, would be considered as a foreign body, not as an impurity, and therefore not a sonim. The studies of sonims of which the results have been published hitherto, have been made chiefly or wholly on finished or at least on cold steel, without much, if any, regard to the specific methods by which the steel was made. While many of the results so obtained are valuable, they give little help in determining the cause, effect, or cure of the disease. It is not enough, in such a study, to know merely the commercial name of the process; for within the field of each process lies a great number of possible variations, each of which will yield a result differing in some respect from all others; and the control of sonims is particularly dependent. on the metallurgical treatment of the metal, because of the inability of analytical chemistry to throw much light on their presence, condition, and effect, as they usually occur in commercial steels. The microscope aids more, perhaps, than chemistry in their study.

Apr 1, 1911

By E. P. Sadowski, R. J. Raudebaugh

A study of micro structural characteristics of a 30 pct Cr, 42 pct Ni, 26 pct Fe alloy has been correlated with its behavior in creep and rupture tests at 1400°, 1600°, and 1800°F. Nitrogen pickup observed at 1600" and 1800°F was associated withfissur-ing of specimens prior to fracture. IN studying the high-temperature characteristics of a nominally 30 pct Cr, 42 pct Ni, 26 pct Fe alloy certain anomalies were observed, namely: The alloy had greater stress rupture and creep strength at 1800" than at 1600° F for time periods beyond 550 hr. As placed in test, this alloy was nonmagnetic. After test, some specimens were found to be fairly magnetic. The gain observed in magnetic response was not solely a function of time and temperature of testing. This is a report of the observations and a recounting of the results of studies made in an attempt to explain the behavior of the material under investigation. MATERIAL AND PROCEDURE All test material was taken from a production size heat of an experimental alloy melted and processed using commercial practice and having the following percentage composition: C Fe Cr Ni Ti 0.05 25.83 30.13 41.59 0.41 Al Mn Si S Cu 0.42 0.75 0.45 0.011 0.34 The material was tested in two conditions, namely mill-annealed and grain-coarsened. Mill annealing, which consisted of heating to about 1900° F in a continuous furnace for about 30 min and air cooling, gave a grain size of ASTM 8 and finer. To produce the grain-coarsened condition, mill-annealed material was soaked for 2 hr at 2050°F in a laboratory furnace and air cooled. This resulted in an ASTM grain size of 4 to 5. Rupture tests were carried out at 1400, 1600, and 1800° F in accordance with ASTM procedures. In tests where only rupture life and elongation at fracture were determined, specimens of 0.252 in. diam and 1 in. gage length were used. In tests where creep curves were obtained, specimens were of 0.375 in. diam and 4 in. gage length. Several of the tests under relatively low stress were discontinued short of rupture. Three low-stress tests are still in progress at this writing. Structural changes which occurred during testing were determined from examination of the tested specimens by light microscopy and X-ray diffraction. Diffraction pattern recordings were made with a diffractometer using copper radiation on samples heavily etched in a picric-hydrochloric

Jan 1, 1960

By William M. Shepard

The Tintic mining districts of central Utah com- prise one of the major silver-lead producing areas in the United States. Ore valued at nearly $450 million has been produced from these districts since the initial discoveries, in 1869, of veins cutting the Silver City monzonite stock. Subsequent production from the famous manto-type "ore runs", which characterize the Main Tintic district, was followed during the past 40 years by discovery of the blind orebodies of the East Tintic district, including the famous Tintic Standard mine and the most recent discovery, the Burgin mine, currently being brought to full production by Kennecott Copper. The occurrence of blind orebodies of exceptional size and grade in both the Main and East Tintic districts has made this area a field laboratory of major importance for the study of geochemical dispersion halos and alteration features associated with known ore, and has led to the discovery of additional concealed orebodies. The larger share of the basic data-gathering and interpretation has been done by members of the U.S. Geological Survey who have been studying the Tintic mining areas since before the turn of the century. These studies have been supplemented and expanded by the geological staffs of the local operating mining companies, by exploration geologists and by students.

Jan 4, 1966

The following is an incomplete list of members and guests who called at Institute headquarters during the period Nov. 10, 1918 to Dec. 10, 1918. Arthur C. Adair, Camp Meade, Md. L. S. Mitchell, Montreal, Canada. Arthur K. Adams, Camp Humphreys, Va. T. E. Mitchell, San Francisco, Cal. Toner Antisell, Chevy Chase, Md. H. Mortimer-Lamb, Montreal, Canada. V. W. Aubel, New Castle, Pa. Edmund Newton, A. C. Black, El Paso, Tex. Paul T. Norton, Jr., Columbus Ohio. 0. F. Brinton, Baxter Spgs., Kans. Elmer W. Pehrson, San José, Cal. C. S. Corbett, Minneapolis, Minn. Joseph E. Pogue, Washington, D. C. W. M. Corse, Mansfield, Ohio. T. C. Roberts, E. Orange, N. J. G. C. Crossley, Toms River, N. J. D. R. Semmes, Richmond, Va. H. S. Emlaw, Grand Haven, Mich. H. L. Slosson, Jr., San Francisco, Cal. Rudolph Emmel, Boston, Mass. W. H. Staver, S. G. Garrett, U. S. N. R. F. A. L. Sweetser, Boston, Mass. Lt. Francis Geib, Denver, Colo. Lt. H. B. Taylor, Kansas City, Mo. Wm. E. Hubbard, Wichita Falls, Tex. Kirby Thomas, New York. Arthur Iddings, Wichita Falls, Tex. Benj. F. Tibby, Salt Lake City, U. Zay Jeffries, Cleveland, Ohio. J. L. Towne, Whitepine, Colo. S. J. Kidder, Mogollon, N. M. Chas. W. Tubby, St. Paul, Minn. Lt.-Col. W. H. Lanagan (Engrs.). A. G. Waite, Brookline, Mass. Major W. F. Lewis (Engrs.). Timothy D. Walsh, Denver, Colo. 0. M. Lewyn, Thomas Warner, Phoenix, Ariz. A. McClintock, DeKalb June., N. Y. J. P. B. Webster, London, England. Major Donald G. Miller, N. M. E. W. Westervelt, Los Angeles, Cal. C. E. LeN. Arnold, formerly with the Inspiration Cons. Copper Co. at Inspiration, Ariz., has accepted a position with the Consolidated Arizona Smelting Co. at Mayer, Ariz.

Jan 1, 1919

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By H. D. Outmans

The author applies the theory of hydrodynamic stability to fluid flow in porous media and concludes that the displacement of miscible liquids is stable if the stability coefficient, as defined by Eq. 19.2 or Eq. 27.0, is positive. The conclusion is invalid, however, since it is based on a faulty argument. To demonstrate this, the reader is referred to Eqs. 4.1 through 4.5 of the paper which describe, in differential form, the first-order disturbances c, u, v, w and p. In these same equations, cx, cz, gl, g3 and are functions of the stable concentration c. This concentration c is known and depends on x, z and t (the author assumes cy = 0). It follows that cx, cz, gl, g3 and µ are also functions of x, z and t. With this in mind, we turn to Eqs. 8.1 through 8.5 which were derived from Eqs. 4.1 through 4.5 by substituting Eq. 6.0. The significance of this substitution is that the author thereby limits the solutions of Eqs. 4.1 through 4.5 to equations of the form of Eq. 6.0. Eqs. 8.1 through 8.5 represent an infinite linear system with five unknowns: c, u, v, w and p. The coefficients cx, cz, gl, g3 and µ in this system are known at each point and at each instant; the coefficients containing derivatives of f are unknown. If this infinite linear system in c, u, v, w and p is to have a nontrivial solution, then it is indeed necessary (as the author states) that the determinant of the coefficient matrix of Eqs. 8.1 through 8.5, i.e., ( A 1, be equal to zero. This condition, however, is not sufficient. A non-trivial solution exists if, and only if, the rank of the coefficient matrix of the entire infinite system is smaller than five. In other words. all minors of order five must vanish and only if all the coefficients in Eqs. 8.1 through 8.5 are constant is this equivalent to the condition |A| =0. Constant coefficients means that gl, g3 and µ, for instance, are constant; and, since they depend on c it follows that c must be constant. We conclude that the condition I A I = 0, on which the author bases his calculations, is necessary and sufficient for a nontrivial solution only if the concentration c is constant. In other words, the author does not investigate the stability of a miscible displacement but, rather, only the stability of the flow of a homogeneous liquid. Using the initial condition and the fact that the coefficients are constant, we find