Search Documents

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Samuel Filgueiras Rodrigues

An austenitic stainless steel ISO 5832-9 was deformed in a torsion test machine over the temperature range of 1,000°C – 1,200°C and strain rates of 0.05, 0.1, 1.0 and 5.0s-1. The Steel plastic behavior was studied by analyzing the flow curves shapes and using the constitutive equations under the conditions of thermomechanical treatment. The curves initially presented an increase in stress characterized by hardening work, followed by a drop in stress to an intermediate level that reached or not, for certain conditions, the steady state softening. The plastic flow curves of ISO 5832-9 steel displayed in three different ways: (i) Curves with continuous softening presenting plastic instability for low temperatures and high strain rates; (ii) curves type flat, here after the peak there is little variation of stress with strain presenting softening mechanism by higher contribution of dynamic recovery at low temperatures and low and intermediate strain rates; (iii) curves with softening after the critical deformation favored by high temperatures and low strain rates. These behaviors indicate the influence of the stacking fault energy (SFE) and precipitated particles on the softening kinetics of this steel.

Aug 8, 2018

By Diego José Inforzato

Hot tensile data were correlated with creep data, in Aluminum Alloy AL7475-T7351, as part of a broader research program, aiming at the validation of a methodology that proposes an equivalence between the two kind of results, for metallic materials in general. The methodology is based on a criterion that establishes correlation among the following parameters from each test: the strain rate, ultimate tensile stress, and time to reach the ultimate tensile stress, in tensile tests, are equivalent respectively to the: minimum strain rate, applied stress and rupture time, in creep tests, for a given test temperature. The present material was tested at 3 temperatures: 133,166 and 193ºC, using 3 nominal tensile strain rates in the hot tensile tests: 3.2x10-6, 1.6x10-4 and 6.4x10-3 s-1 and 9 applied stress levels in the creep tests, varying from 140 to 400 MPa. The conversion of the hot tensile data to creep-like data allowed performing the analysis of all the results together according to the traditional creep relations proposed by different authors, namely: Norton, Arrhenius, Zener-Hollomon and Monkman-Grant, with the determination of the corresponding parameters in each case. The equivalence between hot tensile and creep data is also confirmed for this aluminum alloy.

Aug 8, 2018

By Vitor Guarnier Domiciano

The need to adjust the monolithic refractories to increasingly severe and unstable Blast Furnace casthouse operating conditions has been a major challenge for refractory suppliers in order to guarantee the runner’s safety and its availability for operation. This paper presents the properties of a new robust single line Al2O3-SiC-C refractory castable developed to endure the severe operating conditions that main runners are facing in today's Blast Furnace casthouse scenario. Practical results during almost one year of testing revealed a significant lower wear speed of the new refractory lining when compared to a standard product.

Aug 1, 2018

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Zhi Zhang

The ever increasing demand of high performance rolls in the late finishing stands (F5 – F7) for hot strip mills (HSM) requires better product solutions from roll suppliers. Roll development activities never stop at Union Electric Åkers (UEÅ) in order to meet the requirement. The HYBRID STEEL, a new concept of roll materials especially for the late finishing stands in the HSM, is successfully developed in UEÅ. This paper reviewed the development of previous ICDP as well as enhanced ICDP (eICDP) roll materials, and, the novel HYBRID STEEL roll grade. Rolls manufactured by this new grade have been used in several European mills. A significant improvement over the enhanced ICDP rolls has been observed.

Oct 30, 2017

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Carlos Martins de Oliveira

The trucking industry is constantly seeking improvement and cost reduction of their vehicles, studying new lighter and robust materials to meet the needs of its customers. The objective of this work is to study the application of DCPD Telene, PU. R. RIM and PP-TD 20 materials in aesthetic components of trucks: bumper, calender, upper and lower bracket and side air deflector. A multifunctional work team was created to work in such parts of IVECO trucks. The work began with an analysis of possible improvements to the current parts and followed the subsequent phases: definition of new materials, virtual modeling, new tools, and durability test in vehicles. It could then be verified that the proposed DCPD Telene, PUR. RIM and PP-TD 20 materials showed greater strength, better painting surface, and reduced weight and cost in parts.

Aug 8, 2018

By Giulio Rodrigues Altoé

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of epoxy matrix composites reinforced with continuous fique fiber, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Aug 16, 2017

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By Javier Martinez Rubio

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 16, 2017

By Alim Ullah

The paper discusses the necessity of upgrading low-iron containing ores, giving as an example, NML-Tata Steel Project in the Quebec-Labrador region of Canada. As cooling of pellets is generally a bottle-neck in most pelletizing plants, examples are given of the methods used to improve cooling in the existing plants and a simple, low-cost alternative, tested on a pot-grate system, is presented. The procedure described is applicable to sinter plants also. The trends in iron and steel production worldwide are then given, as well as the reasons for the increase in steel production by the Electric Arc Furnace (EAF) route. The stoichiometric and thermodynamic requirements for producing iron, irrespective of the process, are explained. The different ironmaking processes, especially the Direct Reduction (DR) ones are briefly discussed, outlining recent improvements made to some of them. The pros and cons of producing cooled DRI and Hot-Briquetted Iron (HBI) are given with predictions made for their future growth. An alternative to cold-briquetting of DRI fines is also discussed. Highlights of an ironmaking processes which is at the laboratory/pilot plant stage are given.

Aug 1, 2018

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Breno Totti Maia

In these hard days for Brazil steel market, all steel shops want to achieve the same goal, work with: productivity, low costs and high performance. In this scenario the Slagless® technology (which is applied into BOF converter) was important to reach these targets. After use has been reduced the number of times of tip exchange in more than 04 times. Was reduced too, the time to remove lance skulls. Lance keeps clean during all his life with record number of the life 1255 .Blow keep stable due strong measure control at the nozzles and more improvements are planning.

Oct 30, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita de zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetaram a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução foi 85%, para 100% CO, 1373 K e 105 min, e 52%, para 50% CO, 1373 K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373 K durante 105 min.

Aug 16, 2017

By Christian Geerkens

Increasing requirements on slab quality initiates SMS group in developing products with a high sophisticated level regarding production and process. These characteristics are represented by SMS group’s HD family. HD stands for High Definition or the improvement of product quality via higher precision of the casting processes. A deep look inside into casting process is realized by the use of fiber optical equipped HD mold. High definition casting process control is assured using the HD spray and HD size. For objective, environmentally friendly and highly informative analyze of the inner quality of the cast products the new HD scan is present.

Aug 16, 2017

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Christian Overhagen

In bar and wire rod mills, rolling procedures featuring three- and four-roll technologies are state-of-the-art to produce high-quality long products. While a rolling model for the three-roll process including an equivalent pass method was already presented by the author, pass design methods are dealt with in the current work. The geometry of the rolled product and roll grooves are described mathematically using functional contours, allowing geometric-numerical methods to be used for manipulation and deformation simulation of the rolled product. For a given pass, the output section is constructed using these methods. Roll force, torque and rolling power are calculated using the mathematical rolling model presented before. Interstand tensions are discussed as influencing parameters on the force, torque and power demands, as well as on the section shape. A mathematical model for the influence of interstand tensions on lateral spread is incorporated in the model. To complete the pass design model, elastic mill stand feedback is considered in terms of a fixed elastic modulus for each rolling stand, the elastic feedback and therefore cross-sectional variation due to elastic mill spring being calculated iteratively from the roll force by application of the Gagemeter equation. The interaction of section height and width faults due to elastic mill spring and spread variations is analyzed in detail and the consequences for the roll pass design are shown.

Oct 1, 2019