Search Documents

By David Winter

The geotechnical design, construction, and monitoring aspects of a tied back excavation 85 feet deep in Seattle, Washington are presented. The excavation was completed in overconsolidated deposits of sand, silt, and clay. Lateral soil pressures used in shoring wall design were the lowest to date for an excavation of this size in Seattle. Instrumentation data collected from hydraulic load cells and inclinometers were analyzed and are discussed. The data suggest the actual soil pressures felt by the wall were lower than the design values. Recommendations for future study, as well as future design modifications are given.

Jan 1, 1987

By L. Lacerda

Spray-on ground support membranes (GSM) or thin support liners hold today perhaps as much potential to impact underground (u/g) ground support operations as dry and later wet-mix shotcrete when introduced to mining in the latter part of the 20th century. This emerging technology has come a long way from the time the first single component experimental coatings were tested in the mid-1980s. Due to a number of factors, including occupational health risk and mine safety regulations, it has taken quite some time for the development of non-hazardous membrane products. However, at this junction most existing u/g mines that employ more conventional forms of ground support could benefit from evaluating GSM technology as a means of improving safety and the bottom line. The same is especially true for future mine developments. This paper describes Master Builders Inc.’s CS1251 GSM product and its implementation. It discusses the situations in which GSM may replace other forms of ground support. Furthermore, it evaluates GSM costs & safety issues and looks at present applications and the potentially bright future of this technology.

Jan 1, 2002

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

This paper summarises the development t,) date for the Hidden Valley Gold (HVG) Project. It starts with the original exploration work, covers the detailed feasibility study activities and concludes with the current phase of extra exploration drilling. A brief technical summary has been made from the various mining, process and environmental studies that were undertaken as part of the project approval process. A discussion of the influential non-technical factors is included, as well as a view of the future prospects for an operating mine. The project was always seen as marginal, given the low grades, small resource and short mine life. However the capital and operating costs were lowered with aggressive design and it was regarded an acceptable development by CRA. The opportunity was taken to review the project when delays in start-up were encountered. An updated financial evaluation showed a subeconomic resource in 1990 terms and this resulted in a new exploration phase to identify a larger deposit.

Jan 1, 1991

By Maurício Covcevich Bagatini, Maycon Athayde

Nowadays, the HPGR (high-pressure grinding rolls) is an intermediate step between filtering and balling in the most modern iron ore pelletizing operation. The operation debottlenecks filtering process and reduces pressure over the typical milling process to control particle size to the balling. The present study evaluated aspects of microwave application to the iron ore concentrate fed to HPGR in a bench scale unit. Iron ore concentrate was irradiated varying the microwave exposure time and grinding efficiency was evaluated. The moisture influence in the HPGR efficiency was also assessed. The pellet feed blaine surface area (BSA) improved by 300 cm2/g and % < 325# fraction by 3%. Scanning electron microscope (SEM) images show the formation of micro-cracks onto the particle surface induced by microwave; the effect observed helped improve the milling process performance, in addition to the moisture reduction observed due to the temperature increase.

Notwithstanding full concurrence with the dictum of a famous scientist that &quot;definitions are the most accursed of all things on the face of the earth,&quot; in view of the considerable confusion which exists in jigging nomenclature, it is considered advisable to commence this paper with the following explanations of the terms which will be used throughout the text.Jig Bed. The whole layer of material lying on top of the jig screen.Ragging. The layer of denser material lying immediately above the jig screen, which is too coarse to pass through this screen and is confined horizontally by the cells of the top grid.Ore Column. The layer of ore pulp between the ragging and the top-water.Top Water. The water, carrying fine material in suspension, which flOiWS over the surface of the jig bed.Hutch Water. The water added to the jig below the screen. (Except for the water discharged with the hutch concentrate, the &quot;hutch-water&quot; eventually becomes &quot;top-water.&quot;)Feed Water. The water in the ore pulp fed to the jig.(This water becomes part of the &quot;top-water.&quot;)Pulsion. The period of the jigging cycle during which the water is moving upwards relative to the particles in the jig bed.

Jan 1, 1937

By Marcus Wolter Ferreira

O objetivo deste trabalho é desenvolver uma metodologia para aprovação de tubos com alta resistência a colapso de acordo com os requisitos da norma internacional API5CT grau N80, produzidos por tratamento térmico de tempera e revenimento, utilizando fornos de indução em tubos fabricados pelo processo de soldagem com resistência elétrica em alta frequência (ERW/HFIW). Neste trabalho são exploradas as principais propriedades mecânicas e dimensionais de um tubo de revestimento com diâmetro externo de 177,8 mm e parede 8,05 mm grau N80 processado para atingir alta resistência a colapso, onde serão apresentados os resultados do processo de qualificação para validação de sua produção em série.

Oct 30, 2017

Comparing Energy Efficiency of Multi-Pass High Pressure Grinding Roll (HPGR) Circuits With increased emphasis on reducing costs and carbon emissions in mineral processing, it is becoming essential to employ the most efficient comminution devices and to use them to maximum effect. High pressure grinding rolls (HPGR) are considered highly efficient compared with other devices, however their relative efficiency in multi-HPGR circuits is less well understood. A series of comminution tests was carried out to evaluate three multi-pass HPGR circuits and a jaw crusher-ball mill circuit. Combinations of HPGR units (1.0 m and 0.25 m diameter), jaw crushers and Bond ball mills were used to grind a 32 mm top size porphyry copper feed (BBWI = 12.1) to a product P80 size of about 150 ¦m. Up to three passes of HPGR were used in each circuit, with energy measurement and size analysis at each point in the comminution process. The energy efficiencies of individual comminution stages and of the overall circuits were quantified and evaluated using three different approaches. The operating work index method for comparing comminution energy efficiency underestimated HPGR performance due to the large amount of fines generated. The -75 ¦m efficiency factor and F50/P50 reduction ratio interpolation methods both give a fairer measure because they better take into account the amount of fines generated by HPGR. The results show that the relative comminution efficiencies of the three multi-pass HPGR circuits tested differ by as much as 22%, providing insights as how to best employ HPGR in a comminution circuit. The most energy efficient of the circuits tested was a three-pass HPGR circuit with a 1.0 m diameter roll on the first pass in closed circuit with an 8 mm screen followed by a second and third pass in a 0.25 m roll.

Sep 13, 2010

By Lucas Andery Reis

No processo de beneficiamento mineral, a moagem é o último estágio da etapa de cominuição de minérios responsável pela redução das partículas à liberação do mineral a ser concentrado nos processos subsequentes. Um problema presente nesse processo é a moagem em excesso do material, que aumenta a potência consumida na moagem, dificulta a recuperação das partículas muito pequenas nas etapas de concentração e prejudica a operação de filtragem do processo de pelotização por entupimentos ocasionados pelo material mais fino do que o especificado. Para melhorar o desempenho da moagem e reduzir seu custo operacional, se faz necessário estudar estratégias de controle adequadas que controlem melhor as diversas variáveis existentes nesse processo. Nesse sentido, o objetivo desse trabalho foi utilizar um simulador de circuito de moagem com o intuito de comparar o desempenho da planta sendo controlada por controle clássico (PID), que é amplamente utilizado em circuitos de moagem, e por controle preditivo por modelo (MPC), que é aplicado em uma camada acima dos PIDs. Foi possível concluir que o circuito de moagem sendo controlado por MPC obtém melhor desempenho do que o PID, possibilitando trabalhar com as variáveis mais próximas de seus limites ótimos de operação.

Oct 30, 2017

By Noan Tonini SImonassi

Como ferramentas simples, moeda ou mesmo como armas os metais tornaram possível o progresso da humanidade. Uma das maiores descobertas já feitas foi o desenvolvimento do aço. Com o avanço da utilização desse material foram desenvolvidas técnicas de adição de elementos de liga assegurando propriedades que possibilitam a sua utilização em praticamente todos os setores da indústria. O objetivo do presente trabalho é avaliar a evolução do comportamento mecânico de um aço do tipo AISI 4340, submetido a tratamentos térmicos de têmpera e revenimento. As amostras estudadas neste trabalho foram obtidas de discos tracionadores que são parte de ferramentas de preparação do cabo de sensor utilizado durante a produção de petróleo. Antes da têmpera estas peças foram submetidas a um pré-aquecimento lento até a temperatura de 815°C e, posteriormente, submetido à austenitização acima de 1.000°C por um tempo determinado a fim de difundir os elementos de liga de maneira homogênea na liga. Após a têmpera, estas foram submetidas a seguidos processos de revenimento. A evolução da dureza do material tratado e sua microestrutura puderam ser observadas por meio de análises metalográficas. O comportamento mecânico destas peças obteve melhora significativa com relação às propriedades de interesse.

Aug 8, 2018

By R. J. Woody

Design of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 1, 1959

By H. Kenworthy

"INTRODUCTION ..Although the occurrence of iron ore in Missouri was recognized by Marquette as early as 1673, the first known mining and smelting operation was conducted in 1815. This operation was near Arcadia, Iron County, the first of its kind west of the Mississippi-Ohio River system. Several small furnaces of short life were erected in Missouri in the ensuing 30 years. However, until the extensive deposits of Iron Mountain and Pilot Knob were opened between 1843 and 1850, the state remained a minor producer of iron. It was this district which was chiefly responsible for the prominent position Missouri held in the iron industry until the late 1880's. At this time the easily minable high-grade ores became exhausted and the discovery of the immense Lake Superior deposits depressed the raw-ore price to such an extent that any mines ceased to operate. 3/Small yearly production of iron ores continued in Missouri to the present. Owing to war demands for hard ore suitable for open-hearth steel, the M. A. Hanna Co., through its subsidiary, the Ozark Ore Co., reopened the Iron Mountain, deposits and installed new equipment in an old concentrator to handle the low-grade ores left from previous operations. At present, ore production is from open pits, but underground mining is contemplated in the future. About 2,000 tons a day of iron ore is treated by gravity concentration of material from the open pits in the immediate vicinity. The concentrate is shipped to the Birmingham, Ala., district and to Granite City, Ill., for smelting. The coarse tailing is sold for ballast and concrete aggregate. The iron requirements of the concentrate stipulated by the purchaser are not difficult to meet, but the phosphorus is frequently higher than desired. For 1946 the concentrates averaged 54.18 percent iron and 0.235 percent phosphorus with low sulfur. The Ozark Ore Co. concentrate, however, sometimes contains as much as 0.40 percent phosphorus. The phosphorus in ores from those portions of the deposits wherein the phosphorus occurs with siliceous gangue is readily rejected in the milling, but in much of the ore the phosphorus is associated with the iron and concentrated with the iron minerals. Selective mining is impossible owing to the spotty occurrence of the phosphorus mineral. Often within 5 feet the ore will change from low phosphorus to high phosphorus, and it would be expedient to find a method of rejecting enough phosphorus at the mill from the latter type of ore to meet the phosphorus specification."

Feb 1, 1948

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By S C. Dominy

The grade of ore at Marvel Loch mine is directly related to the presence or absence of shear zones and quartz-sulfide-rich hornblende (¦ diopside) veining within areas of plagioclase alteration. An experienced geologist can identify these features in hand specimen. Practical rules have been developed to assist this visual identification. The structural sites and styles of alteration and veining most conducive to gold mineralisation have also been determined. The work has enabled a better understanding of the geological controls on mineralisation at Marvel Loch, and has clarified geological understanding for optimisation of grade control modeling, ore block mark-ups, and minimisation of ore loss and dilution during excavation. In addition to this, it has enabled a detailed understanding of mine scale structural controls, geometry and relative grade relationships.

Jan 1, 2003

By Mónica Maria Jiménez Correa

A geração de resíduos sólidos tem se convertido em um problema para a sociedade. Milhões de toneladas de resíduos sólidos são produzidos diariamente no mundo causando numerosos problemas ambientais e sociais. Além disso, o acelerado consumo junto com o avanço tecnológico e o curto ciclo de vida dos produtos têm elevado a quantidade e complexidade dos resíduos sólidos descartados, tornando a situação ainda mais complicada. Nas últimas duas décadas, a indústria de equipamentos eletroeletrônicos (EEE) tem acelerado sua produção vertiginosamente, tendo como resultado o subsequente aumento na geração de resíduos de equipamentos eletroeletrônicos (REEE). Os REEE apresentam na sua composição materiais tóxicos e se descartados irregularmente, podem contaminar o meio ambiente e causar danos à saúde publica. Por outro lado, a sua reciclagem é um assunto que merece atenção especial, não só do ponto de vista de tratamento de resíduos, mas também do ponto de vista econômico. A fim de contribuir com a reciclagem e a diminuição dos resíduos sólidos, o presente trabalho pretende apresentar um estudo do processamento mecânico das placas mães de computadores descartados, visando recuperar o cobre, o níquel e o zinco presentes no resíduo.

Aug 7, 2018

By Carlos Alexandre Gonçalves de Moura

O trabalho se baseia na redução do retorno parcial de aço por temperatura na Aciaria LD com foco em análise estatísticas do processo, melhorias no projeto alinhado ao plano de manutenção dos componentes mecânicos e elétricos do sistema de aquecimento de panelas. Para análise do problema foi elaborado um estudo utilizando Lean Six Sigma através do DMAIC, analisando as condições de processo, procedimento operacional e plano de manutenção dos equipamentos. Como resultado do trabalho obteve-se uma redução em 58% no retorno parcial em panelas de aquecedor.

Jul 30, 2018

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By Beatryz C. Mendes, Henrique de Paula Santos, Kléos M. L. Cesar, Eduardo Antônio G. Marques, Maurício Paulo F. Fontes, Rita de Cássia S. S. Alvarenga

Inadequate discard of industrial solid waste is a risk to human health and to the environment. Aiming at softening environmental damage caused by deposition on soil of an ink residue, from washing of printers used in carton box packages, it is intended to incorporate this residue into soil-cement bricks. The residue has other use potentialities such as in screeds, pavement parts, fertilizer, paints, etc. However, to explore these potentialities it is fundamental to assess the risks that the several forms of use of this residue can cause. For such, in this work the chemical analysis of the residue was performed in order to know its main chemical compounds, in addition to its characteristics of leaching and solubilization. The chemical composition assay showed traces of some heavy metals such as Pb, Cd, Cr, Zn, Al and Cu, although the residue-generating company uses ink labeled as heavy metals free. Among the elements analyzed in leaching and solubilization, some had concentration above the limit allowed by The Brazilian Codes. This code is based on CFR—Title 40—Protection of Environment—Part 260–265—Harzardous waste management. Therefore, it is suggested that the residue has a limited use to avoid contamination of ground water.

Mar 1, 2017