Search Documents

President John T. Atkins on behalf of The RMCMl officers and Executive Board, invites you and your family to attend The 80th Regular Meeting and Convention of 'The Rocky Mountain Coal Mining Institute to be held at Marriott's Mark Resort, Lionshead Village in Vail, Colorado JUNE 24 - JUNE 26, 1984

Jan 1, 1983

By J. L. Kearns

The importance of optimizing equipment replacement decisions becomes more critical each year due to the rising costs of buying new equipment versus maintaining old equipment. Replacing equipment when it is physically worn out, or replacing it too soon or too late relative to its Economic Life (when it is economically worn out), is very costly. After extensive literature review and research, Kennecott has developed its Equipment Replacement Guide (ERG) system which identifies, evaluates, and justifies the replacement of uneconomical equipment. The system considers such critical factors as inflation, decreasing work capability, increasing maintenance/repair and operating costs, taxes, time value of money, return on investment, salvage value, and investment tax credit. These factors are used in a system of equations which balance the costs of new equipment against the total operating costs of old equipment. The solution of the equations determines the Economic Life of equipment. Replacement of equipment at the determined Economic Life will earn the specified, required return on investment that is used in the calculation of the Economic Life.

Jan 1, 1979

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

By D. KEYS, D. E. Gemmell

The portion of the earth's surface covered by peatlands has been conservatively estimated at over 420 million ha (Kivinen and Pakarinen 1980). It is estimated that there are about 170 million ha of peatland in Canada. New Brunswick contains about 140,000 ha. Harvesting of peat for horticultural purposes has been carried out in New Brunsiwck since 1942. This industry, and the potential for using peat for energy purposes, indicated the need for an accurate assessment of the resource. In 1975, therefore, the New Brunswick Department of Natural Resources began a detailed peatland inventory. Assistance from the Canada Department of Regional Economic Expansion permitted acceleration of this program and field work was completed in 1982. Information gathered by the program will form the basis for a management plan for future use of the resource.

Jan 1, 1984

By Kevin Erwina, Rajiv Chandramohana, Connor Meinkea

This paper explores prevalent operational challenges encountered globally in SAG mills, including suboptimal throughput, liner wear, excessive energy consumption, and SAG mill load stability. The paper delves into the root causes behind these issues, such as ore variability, poor operating strategy, or inadequate process control. Drawing on industry experience and case studies, the paper highlights the significance of addressing these challenges to enhance overall mill performance and efficiency. It underscores the necessity of tailored strategies, encompassing improved monitoring, optimized liner designs, and refined control techniques to mitigate these challenges and promote sustainable SAG mill operation.

Feb 1, 2024

By Kim Appleby

Epithermal gold-silver (lead-zinc-copper-manganese) mineralization on Misima Island is confined to steep and reactivated flat-lying normal faults in the upper plate of a major, shallowly dipping detachment fault. The hangingwall comprises an Eocene metavolcano-sedimentary sequence that has been extensively intruded byMiocene calc-alkaline granodiorite. It is unconformably overlain by Pliocene sedimentary and volcanic rocks. High-pressure amphibolite facies rocks dominate the footwall and have many characteristics of a metamorphic core complex. Mafic-alkalic lamprophyre dike swarms intrude the hangingwall and footwall sequences. Previous workers attributed the gold-silver mineralization on Misima to the intrusion of the porphyritic granodiorite (Williamson, 1984). This has been proposed for many tertiary gold deposits of the southwest Pacific(Sillitoe, 1989; Leach and Corbett, 1994).

Jan 1, 1996

By S. M. Javad Koleini

Processing of phosphate ore sample was investigated for increasing phosphate content and reduction of its gangue minerals such as carbonates and silicates. Experimental designs were per-formed using Taguchi method. Different flotation methods were investigated for Moundon phosphate ore sample and three methods were used as follow: direct cellophane flotation, reverse calcite flotation and reverse quartz flotation. Because of the sensitivity of cellophane flotation to slime content, prior desliming was carried out before the experiments. Direct flotation experiments carried out and a concentrate contained 23.80% P2O5, 6.88% SiO2 and 72.33% recovery were produced. The achieved P2O5 content in the produced concentrate from reverse flotation of calcite was 26.44% and the recovery was 82.56%. The concentrate products obtained at optimum conditions by direct flotation of phosphate and indirect flotation of calcite were subjected to indirect flotation of calcite and direct flotation of appetite and final concentrates with P2O5 grade of the order of 24.19% and 26.96% were obtained, respectively. It was concluded that one stage direct flotation is unavoidable to achieve a product with low SiO2 content.

Jan 1, 2014

By W. I. Garms

This paper, describing the milling practices at the Hayden concentrator of the Nevada Consolidated Copper Co. is the first of a Series being prepared by the Bureau of Mines on milling methods and costs in various districts of the United States. The Hayden concentrator is located at Hayden, Gila County, Ariz., 20 miles from the mine at Ray, Pinal County, Ariz., and approximately 1-1/2 miles north of the junction of the Gila and San Pedro Rivers. During the fourth quarter of 1928 the concentrator treated daily by flotation an average of 10,336 tons of ore containing 1.25 per cent of copper. The average recovery during this period amounted to 87.84 per cent of the total copper. The concentrates contained 19.88 per cent of copper.

Jan 1, 1930

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By L. F. Bryant, J. P. Hirth, R. Speiser

The surface, gain boundary, and twin boundary energies, as well as the surface diffusion coefficient, of cobalt were determined from tests at 1354°C in pure hydrogen. A value of 1970 ergs per sq cm was calculated for the surface energy, using the zero creep method. It was possible to measure the creep strains at room temperature because the phase transformation was accompanied by negligible irreversible strain and no kinking. Established techniques based on interference microscopy were used to obtain values for the other three properties. The gain boundary and twin boundary energies were 650 ad 12.7 ergs per sq cm, respectively, while a value of 2.75 x l0 sq cm per sec was determined for the surface dufusion coefficient. In the course of a general study of cobalt and cobalt-base alloys, information was required about the surface energy of cobalt. Hence, the present program was undertaken to measure the interfacial free energy, or, briefly, the surface energy, of the solid-vapor interface of cobalt. The microcreep method was selected for this measurement because other surface properties could also be determined from the accompanying thermal grooving at grain boundaries and twin boundaries. A brief summary of the methods for determining the various surface properties follows. At very high temperatures and under applied stresses too small to initiate slip, small-diameter wires will change in length by the process of diffu-sional creep described by Herring.1 The wires acquire the familiar bamboo structure and increase or decrease in length in direct proportion to the net force on the specimen. For a specimen experiencing a zero creep rate, the applied load, wo, necessary to offset the effects of the surface energy, y,, and grain boundary energy, y b, is given by the relation: where r is the wire radius and n is the number of grains per unit length of wire. The first results obtained from wire specimens were reported by Udin, Shaler, and Wulff.' udin3 later corrected these results for the effect of grain boundary energy. The grain boundary energy is determined from measurements of the dihedral angle 8 of the groove which develops by thermal etching at the grain boundary-free surface junction. For an equilibrium configuration: Measurements of the angle 8 can be made on the creep specimens4'5 or on sheet material, as was done in this investigation by a method employing interference microscopy.= If the vapor pressure is low, the rate at which grain boundary grooves widen is determined primarily by surface diffusion and, to a lesser extent, by bulk diffusion. The surface diffusion coefficient, D,, is obtained from interferometric measurements of the groove width as a function of the annealing time, t. As predicted by Mullins~ and verified by experiment, the distance, w,, between the maxima of the humps formed on either side of the grain boundary increases in proportion to if grooving proceeds by surface diffusion alone. For this case: where fl is the atomic volume and n is the number of atoms per square centimeter of surface. When volume diffusion also contributes to the widening, the surface diffusion contribution can be extracted from the data by the method described by Mullins and shewmon.8 Where a pair of twin boundaries intersects a free surface, a groove with an included angle of A + B (using the groove figure and notations of Robertson and shewmong) forms by thermal etching at one twin boundary-free surface junction. If the "torque terms", i.e., the terms in the Herring10 equations describing the orientation dependence of the surface energy, are sufficiently large, an "inverted groove" with an included angle of 360 deg-A'-B' develops at the other intersection. The angles A + B and A' + B' are measured interferometrically. When the angle, , between the twinning plane and the macroscopic surface plane is near 90 deg, the twin boundary energy is calculated from the relation: 1) EXPERIMENTAL TECHNIQUES Five-mil-diam wire containing 56 parts per million impurities was used for making ten creep specimens. These specimens had about 15 mm gage lengths with appended loops of wire and carried loads (the specimen weight below the midpoint of the gage length) ranging from 3.7 to 149.8 mg. The wires were hung inside a can made from 99.6 pct pure cobalt sheet. Beneath the wires were placed small specimens of 20-mil-thick, 99.9982 pct pure cobalt sheet from which the relative twin boundary and grain boundary energies and the surface diffusion coefficient were measured. All the specimens were annealed at a temperature of 1354" i 3°C which is 92 pct of the absolute melting point of cobalt. The furnace atmosphere was 99.9 pct pure hydrogen that was purified further by a Deoxo catalytic unit, magnesium perchlorate, and a liquid-nitrogen cold trap. As a precautionary measure the gas was then passed through titanium alloy turnings which were heated to 280" to 420°C and replaced after every test period. The hydrogen was maintained at a

Jan 1, 1969

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By S. H. Lorain

This paper briefly describes the principal known commercial and near commercial deposits of gold-bearing gravel end the principal placer mining operations of Idaho County, Idaho. It is one of a series of similar papers on western mining districts. The data used in writing this paper were gathered during the summer of 1937. Information concerning gold-bearing gravels was obtained from prospectors and operators, while operators supplied most of the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1938

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By Ward B

Central Colliery was developed to exploit large underground reserves in the German Creek lease. It was planned from the outset as a retreating longwall operation and is the first longwall mine in Queensland. Longwall mining is not new to Australia but all previous experience has been confined to the coalfields of New South Wales. There was no precedent for longwall extraction in the markedly different geological setting of the Bowen Basin in Central Queensland. Various investigations were thus carried out during the initial development of Central Colliery, prior to the installation of the longwall, to ascertain the geotechnical characteristics of the coal seam and the adjacent strata and to predict the performance of the heading and pillar design as mining proceeds to depth. Laboratory tests showed the coal to be weak with an unconfined compressive strength of 9.6 MN/m2. Site inspection and geophysical correlation revealed a shear zone and extensive intraformational shear planes in the seam. The latter were found to exert a controlling influence on rib reaction in the headings. This behaviour was predicted by finite element modelling of the development headings which indicated that mining induced stresses in the coal would be relieved by block movement of the ribs. A chain pillar width versus depth curve was established for yielding pillar design based on empirical and computational methods. This gave pillar widths from 25m to 48m over the proposed depth range of 150m to 300m. Finite element modelling of the 25m pillars chosen for the first gateroads confirmed the overall stability of the design but suggested that rib spall could be significant in the adjacent tailgate. (1) Chief Mining Engineer, Capricorn Coal Management Pty. Ltd., German Creek Mine, Queensland (2) Senior Engineering Geologist, Coal Division, The Shell Company of Australia Limited, Melbourne

Jan 1, 1986

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results of an investigation of the application of thermal fragmentation in Australian hard-rock, underground, narrow-vein mining. Two geologically similar samples from an underground, narrow-vein, hard-rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method.

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

 This research project explored the viability of a new mining technology — thermal fragmentation — in narrow-vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation as well as one of an existing method used for narrow-vein mining. Comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs as well as increased productivity and ore recovery meant that the new method would improve the financial performance of any operation.

By Weijie Wei, Jinwang Zhang, Shengli Yang

In longwall top-coal caving (LTCC) mining with an inclined seam, the recovery rate is low and equipment stability is poor due to the unbalanced top-coal drawing process. To address these problems, this paper proposes the dynamic group caving method (DGCM), whose basic premise is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Using particle flow code (PFC), the caving mechanism of top coal under DGCM was investigated. The results are of significance to realize high efficiency and precise caving in LTCC mining with an inclined seam.

Jan 1, 1967

Established as a Society February 26, 1957 OFFICERS AND COMMITTEES Wayne E Glenn, President Earl M Kipp, President-elect John S Bell, Past President R A Morse, Vice-President W D Owsley, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 6300 North Central Expressway Dallas 6, Texas

Jan 1, 1960