Search Documents

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

By E. J. Garrison

A.C. Noble presents a clear and concise summary of the factors pertinent to a competent reserve evaluation of a mineral occurrence. However, I believe that he confuses the difference between a resource and a reserve. By definition, a reserve estimate includes all known economic, legal, mining, metallurgical and environmental factors impacting the recovery of the product(s) found in the deposit. A resource estimate, however, is an estimate of what is there - what is available for exploitation and should not include economic and other considerations. Only after defining the resource, its extent, location, physical and chemical properties, can an intelligent selection process begin of the extraction and processing technologies most appropriate to the circumstances encountered. The early and almost certainly inappropriate application of these often cookbook choices has probably lead many companies to walk away from good properties. (How many mines have been found in others rejects?) An example of the process is the early selection of metallurgical samples, after encouraging values are found in a few holes or surface samples, in an attempt to determine the economics of the prospect. Unfortunately, the sampler does not know how representative of the occurrence the sample is because he does not know what the deposit looks like. As a consequence, the property becomes saddled with a bad metallurgical sample that is often inappropriately used in evaluating the deposit which it does not represent.

Jan 1, 1994

By C. Golumbic

Most early research on solvent extraction of coal has been concerned with the molecular structure of coal. Although rush work is continuing, practical aspects of the subject also are being emphasized. For example, development of the Pott-Broche extraction process resulted from the discovery of very efficient solvents for the pressure-extraction of coal. Recently, Orchin and Storch reported the use of even more efficient solvents under similar conditions. In addition to the discovery of more effective solvents, the possibility of efficient extraction at atmospheric pressure is obviously of practical interest. H. J. Rose observed that phenanthrene at its atmospheric boiling point readily dispersed 80 percent or more of Pittsburgh-bed bituminous coal. This fact served as the starting point of the present investigation, ill which determination of the chemical specificity of this solvent and the chemical nature of the resulting extracts was undertaken. This paper represents a progress report of the results obtained to date.

Jan 1, 1950

By Walter S. Weeks

CONFUSION appears to exist in the discussions of fan testing because engineers do not agree on what energy should be credited to the fan in certain cases, and because certain terms that are used in the discussions seem to have double meanings. The purpose of this paper, therefore, is to discuss the useful energy that should be credited to the fan and the methods of determining this energy, and to suggest changes in nomenclature for the sake of clearness. The instruments commonly used in the measurement of fan pressures are the manometer, the static tube, and the impact tube. The static tube is a tube with small pinholes in it. When connected to one leg of the manometer and placed in the air current with the holes facing at right angles to the direction of the current, this tube causes the manometer to register the static pressure, unaffected by the impact of the air. The impact tube is a tube with an opening that faces the air current. When connected to one leg of the manometer, this tube causes the manometer to register a pressure which is the static pressure modified by the impact of the flowing' air on the end of the tube. If the static tube is connected to one leg of the manometer and the impact tube to the other leg, and both instruments are inserted close together in the air current, the static pressure is eliminated and the manometer registers the impact pressure. The efficiency of a fan is the percentage of the expended power utilized in useful work. The items to be included as useful work are a matter of convention, and as the conventions are not universal I feel that the matter is open to discussion.

Jan 1, 1929

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part I of the report contains the results of the field teats.5 The studies were made on an oil lease in a so-called "sour district," near Borger, Tag., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it Was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field teat proved that aluminum lease tanks will withstand corrosion by hydrogen sulphide, but it was found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By J. C. Zelanko

The U. S. Bureau of Mines conducted a multi-faceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps in that the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements, and microseismic monitoring as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading, and microseismic activity were monitored prior to, during, and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and after the face bump. Shield load data which were evaluated in an effort to identify trends which could be used to forecast coal bumps appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1991

By Waddah Akili

This paper describes the steps taken in planning, developing, and executing a case study/ case history course in geotechnical/ foundation engineering at an international university. The paper sheds light on: how a “workable” format for the course was arrived at; the organization of the course; and the results of evaluating the effectiveness of this approach versus traditional lecturing. Problems and challenges that could arise when offering the course for the first time are also addressed. Embedded in this experience and its related protocols are: the emphases on engineering design and the practice, teamwork and leadership development, organizational management, and oral and written communication skills. The paper concludes by confirming that discussions, through an open forum, are judged to be superior to traditional lectures in improving critical thinking, cultivating desirable personal attributes, and acquiring problem-solving skills.

Philip Argall, Denver, Colo. (communication to the Secretary) : Mr. Rickard expresses regret that I have not given more extracts " from the fresh leaves of nature's open book." The quotations used by me in argument were all from nature's open book, and by authorities recognized in the scientific world as being able to decipher nature's unwritten pages, if not lay bare her inmost secrets. The study of -nature should be preceded by a knowledge of her laws. Natural science is but the summary of the observations of the past or an organized and accurate knowledge of the order in which things have been observed to happen. One who ignores the 'knowledge of the past or despises that of the present and approaches nature's open book with a virgin mind but too often finds her

Jan 1, 1895

By Will H. Coghill, C. O. Anderson

In July 1921 , we were assigned by the U. S. Bureau of Mines to an investigation of milling methods in the Tri - State zinc district ( Missouri -Kaneas- Oklahoma district ) . The work has progressed without interruption , and about onehalf of the funds allotted for it has been expended . This preliminary statement abcut the nature of the work and the results so far obtained , has been prepared for the information of the operators , and through their assistance to insure the greatest possible progress during the remainder of the work . A general survey of the district was made , and many of the mining companies cordially offered the facilities of their plants for the investigation . The work was finally centralized at the plant of the 0. M. Bilharz Mining Co. Its manager , F. H. Gartung, and his successor , O. W. Bilharz , have been especially helpful , also the millmen at this plant and elsewhere have rendered assistance without which the work could not have advanced . The Missouri School of Mines and Metallurgy , Rolla, Mo. , and the Miami School of Mines , Miami , Okla . , have given hearty cooperation . The Webb City Iron Works and the Joplin Supply Co. donated some necessary apparatus .

Jan 1, 1922

By S. H. Ash

The Pennsylvania anthracite-mining region is the only one in the world of major magnitude. As the deposits of anthracite in the United States are limited virt113.lly to Pennsylvania, the difficulties of this industry have been commonly considered a State rather than a national problem. However, there is also national interest in the conservation and wise utilization of all fuel resources and in the control of interstate waterways. The anthracite industry is confronted with the very se:;-ious :problem of accumu.lation of water in many of the mines. This problem must be solved soon if progressively higr-er mi~ing costs are to be avoided. The water proble~ cannot be solved by the operating compa,nies without State or Federal aid, or both, owing to the magnitude of the work requir~d, diversity of interests of the coal ana surfa.ce ovmerships, hazard to the whole mining community, and interests affec~ed outside the mining region. The cost of abati~ the ever-increasing_surface seepage to mine workings and of handling this seepage once it }3s occurred is beyond the economic resources of most ope~ating ma.'18.gements. The data in this paper giving the high lights of the water problem and indicating what appears to be a step in the right direction are based upon observations made during the past year that the industry desires and believes it is to the npublic interesttr to keep mine workings free of flood end surface waters.

May 1, 1941

By J. A. Roberson, A. M. Adair

A plate of an 18 pct Ni (250 grade) maraging steel was homogenized, cold rolled, and re crystallized to produce a fine grained, homogeneous structure. The strength properties were then measured as a function of cold rollinq prior to aging. Material in the solution heat treated condition exhibited substantial strengthening from cold rolling. The strength increase and the rate of strengthening were proportional to the amount of cold work. This benefit, of up to 50 ksi, was retained during aging for 3 hr at 900°F. The structures produced by cold rolling and aging have been systematically investigated by transmission electron microscopy. The dislocation debris produced by cold work influences the morphology and distribution of precipitate particles as well as the rate of precipitation. An essential feature of the high nickel maraging steels is a martensitic transformation from y to a with the resultant production of a supersaturated bcc solid solution. This solution decomposes to form precipitates during a subsequent aging treatment.' The martensitic transformation in low carbon Fe-Ni alloys and the mechanical properties of these alloys have been studied extensively.2"4 The carbon content of maraging steel is kept very low to avoid the embrittling Fe3C phase and to minimize the acicular, or twinned martensite common to high carbon steels. Maraging steels are usually strengthened only by heat treatment, but cold working is also quite effective in this respect as was shown by Decker, Eash, and Goldman,' Kula and Hickey,5 and the present work. There is, however, some disagreement between the present results and those of Kula and Hickey. Because of their unusual combination of strength and toughness, the maraging steels are suitable for applications where reliability at high stress levels is required. The strength level is achieved through a combination of solid solution hardening,' substructure hardening,3 and precipitation hardening,6 of which the last is the most important. The toughness of these steels has been reported to be a result of the absence of brittle grain boundary precipitates,7 and the fact that the matrix is a massive martensite rather than a twinned martensite.' One of the problems in the manufacture and use of maraging steel has been its tendency to develop laminations in sheets parallel to the rolling plane.9,10 The present investigation was intended to determine whether or not an improvement in the microstructure of this steel by thermomechani-cal processing would improve mechanical properties. I) EXPERIMENTAL PROCEDURES A plate ($ in. thick) of an 18 pct Ni-250 grade maraging steel* was obtained and examined metallo- "Analysis, wt pct: 18.1 Ni, 8.6 Co, 5.3 Mo, 0.4 Ti, 0.07 Mn, 0.05 Cr, 0.05 Si, 0.002B. 0.1 Cu. 0.05 Al. 0.002 Zr, 0.016 C, balance Fe. graphically. It was found to contain laminations as described by previous investigators. This plate was then annealed at 2100°F for 24 hr to promote homogeneity. Pilot studies on small coupons had shown that this was the minimum temperature required to accomplish homogenization in 24 hr. Since this treatment caused excessive grain growth, the steel was subsequently cold rolled and recrystallized. Cold rolling was accomplished at about 5 pct per pass to a total reduction of 66 pct. The standard solution annealing treatment (1 hr at 1500°F) was adequate to cause recrystallization of the cold worked steel. The recrystallized steel was then cold rolled and ground by various amounts to produce specimens with uniform thickness and selected amounts of cold rolling. All tensile specimens with less than 90 pct cold reduction were ground to a thickness of 0.050 in. Specimens with 90 pct cold reduction were 0.025 in. thick. All

Jan 1, 1970

By Shingo Morimoto, Toru Sasaki, Masato Shinji

"1. INTRODUCTIONTunnel face stability is one of the most important consideration in New Austrian Tunneling Method. In general, if all of the material properties of ground can be obtained through the field investigations, the tunnel face behavior can be predicted using numerical simulation prior to tunnel construction. However, estimating the safety of a tunnel face is difficult, especially in cases where the ground is very weak such as in an urban area.In this study, numerical analyses of tunnel excavation in very weak ground conditions, such as a low cohesion and low internal friction angle, were carried out. The relationship between the average shear strain distribution on the tunnel face and the overburden was analyzed. This relationship estimates the shear strain of the tunnel face relative to the critical shear strain obtained by the ground properties. The critical shear strain was defined as an allowable value for the maximum shear strain. We proposed the allowable overburden as tunnel face stability index (TFI) that satisfies the critical shear strain criterion of ground. Finally, a design chart of the allowable overburden for various cohesion values and friction angles of ground was created. This chart is useful in the preliminary tunnel design stage to judge the necessity of additional counter measures against normal tunnel support design.2. WEAK GROUND MODELING AND ANALYSIS PROCEDURE2.1 Setting material propertiesWith reference to a past study1), the material properties were adopted on the basis of material properties in the standard worst rock classification case called “DII”2) for standard support pattern of weak ground in Japan. The typical material properties for “DII” are listed in Table 1. In addition, Fig.1 shows the distribution of the representative weak ground according to cohesion and internal friction angle. When the internal friction angle is relatively high and the cohesion is weak, the ground is categorized as sandy ground. Furthermore, when the internal friction angle is low and the cohesion is strong, the ground is categorized as clayey ground."

Jan 1, 2016

By J. Hallowell, M. Conley, R. Cook

Inflatable friction rock bolts (IFRBs) are often considered temporary ground support due to their susceptibility to weakening from corrosion. The effective service life of an IFRB can be difficult to estimate due to the multitude of factors that affect the rate of corrosion. Some mine sites have experienced several-year-long service lives of IFRBs without issue, while others experience corrosion-related falls of ground only weeks after installation. The most common industry method of assessing bolt performance is by pull testing the fixture. However, due to the IFRB’s ability to mobilize its full tensile capacity with less than 2 feet of anchored length, corrosion along the bolt at depths greater than 2 feet from the collar cannot be identified using this approach. Alternatively, reinflation testing is a simple and non-destructive method of evaluating the condition of an entire bolt length for breaches in the bolt wall. This can be particularly useful when assessing the extent of corrosive conditions within a particular mining area where instabilities have already occurred and the condition of nearby bolts is unknown, or when re-entering historic mine workings which have not been monitored.

Feb 1, 2023

By Fidelis T. Suorineni

The conditions for rockburst occurrence are traditionally identified as: high stress, high extraction ratio, strong brittle rocks, folding, faulting, and unfavourable excavation geometry. Based on a critical review of case histories, this paper identifies oblique loading of orebodies by the major far field principal stress as a cause of rockbursts. Orebodies subjected to this loading condition are termed orebodies in shear. Orebodies in shear are subjected to compressive and shear loads. The case histories presented unambiguously show that the magnitudes of the far field principal stress alone, and a knowledge of the conventional rockburst causing factors are not sufficient for mine planning and design. The orientation of the major far field principal stress, or for that matter the driving stress relative to the orebody axis, should be recognised as one of the causes of rockbursts. It is suggested that since stress orientation is an important factor, and orientations from stress measurements are so variable, orientations from stress measurement data be complemented with underground observations from borehole and excavation breakouts to determine the actual in situ stress orientation, whenever possible. Also stress modelling for the design of critical elements (pillars) should include a sensitivity analysis on the relative critical field stress direction. The paper emphasises that special attention should be paid to or

Jun 1, 2012

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By C. G. Dunn

Many investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal oricntation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.l--3 Furthermore, it is believed that high-stress regions exist in the vicinity of these bands4. and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallizati~n.5,6 Similar evidence has been published for nonferrous metals5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins cxisted prior to recrystalli~ation.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary oricntation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha iron.9 Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involvc more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By Victor F. Hollister

This first section of case histories of mineral discoveries, Vol. 3, covers some of the milestones in porphyry copper and skam exploration successes. It was during the era of these discoveries that large, complex exploration departments emerged as permanent adjuncts of large mining companies. The discoveries helped shape how and where exploration activity was conducted. Probably the most important factor in exploration success is management. Few management people are mentioned in this section or in any exploration history, yet the distinction between success and failure ultimately rested with the decisions they made. One of the most successful groups was initiated by Roger Straus and Herbert Brownell when they sought to make Asarco into an important metal producer. Relying on Clem Pollock and L.H. (Bill) Hart to identify and push worthwhile projects, the Asarco management remade the company. Asarco will benefit from exploration successes com- pounded by that team for years to come. Duval is an example of a management that decided to add metal production to its industrial minerals output. When Page Morris was president, that company opened three major porphyry copper mines and became an important factor in metals. Under the Monis management team, Duval became a leader in exploration. At the other end of the scale are managements that snatched defeat from the jaws of victory and by so doing changed the character of their companies in other ways.

Jan 1, 1991

By Lech Bolinski, Joe Shirley

Over two dozen Resin-in-Pulp (RIP) plants have been in operation in the fonner Soviet Union since the beginning of 1970. Currently approximately 50% of the gold produced in Russia, Uzbekistan and Kazakhstan, which equates roughly to 10% of the total world output, is recovered using the RIP technology. An alternative to activated carbon, ion-exchange resin has several advantages for the recovery of gold. Resins are less prone to clay or organic foul­ing and do not require thennal regeneration. They also have poten­tially higher loading capacities, faster adsorption kinetics, and are more resistant to abrasion. The original Russian RIP process was based on engineering expertise developed for uranium ore pro­cessing and has a few major drawbacks. The biggest problem is an 18-30 day resin stripping process, which results in a huge gold lock-up. The problem was recently overcome by the development of a new stripping technology which cuts the time to 12-24 hours. Currently, there is rather limited practical knowledge of the Russian RIP process in the West, but often Western mining com­panies developing gold mines in the fonner Soviet Union are hard pressed by their local joint venture partners to take a serious look into RIP. It is probably only a matter of time before one of these companies will cross Soviet technology with Western engineering and develop a modem RIP process as an attractive option to the current CIP and CIL technologies.

Jan 1, 1996

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining com­munity about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

Jan 1, 2008