Search Documents

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By I. Petrovsky

Presence of the ground water, especially flowing water, causes limitations in the type of the explosives, which can be used for the blasting development in the open cats and quarries. This presents really big problem in Russia, because more than 70% of the blasting holes are wet and filled by flowing water. The waterproof explosives need to be used in these conditions, which increases the cost of the blasting development. So the search of the methods to remove the water from the blasting hole and to prevent direct contact of the explosive material with the water is important. It will give possibility to use nonwaterproof explosives (such as ANFO) and decrease the cost of the blasting development.

Jan 1, 2003

By Veronique Falmagne

"In 1987 the only knowledge available of the Ansil orebody was that it was high grade, deep and relatively small . High stresses were also anticipated because there had been rockbursts during shaft sinking and destress blasting had been necessary (Fig. 1). From the design, through the development and now in the mining stage, rock mechanics and microseismic monitoring have been used to maximize recovery and safety and minimize dilution. Examples are given of the use of a microseismic monitoring system in the early stages o f mining. This paper also presents a review of the mine's in situ stress measurement campaign, cable bolting practice and backfill procedure.The Design PhaseAfter the initial mapping and classification work, preIiminary numerical modelling was performed using assumed stresses of ov = oH and oH = 3ov• The empirical Mathew's analysis was then used to optimize stope dimensions based on geomechanics data available at the time (Bawden et 01., 1988; Falmagne, 1987; Potvin et 01., 1988). Because of high stresses predicted by numerical modelling and a brittle, strong and relatively unfractured host rock which was believed to be rockburst prone, it was decided to mine without temporary or permanent pillars. However, in order to satisfy production rates, the orebody had to be broken up into two horiwns separated by a triangular pillar (Fig. 2). The final mining sequence is shown in Figure 3.The Development PhaseAt this point, based on work accomplished to date, including mapping and observations from drifting and modelling, the following problems were identified: (1) flat backs in the hangingwall andesite were thought to be highly stressed; (2) flat backs in weak massive sulphide ore would also be subjected to high stress and be difficult to support; (3) the felsic dyke was noted as a "" stress raiser"" , because activity increased as drifts approached it; and (4) chlorite coating of joints in the hangingwall was thought to be an important factor in reducing their stability."

Jan 1, 1991

By E. P. Youngman

In the Unfederated Malay States, with the exception of Johore, the rights of suzerainty, protection, and administration were transferred by giam to the British Government in 1909. In the States of Kelantan, Trengganu, Kedah, and Perlis, the rulers are assisted by State Councils and by British advisers appointed by the British Government.3 With respect to Johore, the largest, richest, and most highly organized of the Malay States not in the Federation, the treaty of December 11, 1885, with Great Britain, defined the relations of the State to the British Govern- ment and allowed the Maharaja to assume the title of "Sultan"; an amendment to this treaty (May 12, 1914) provided that the Sultan should be advised by a British officer, the General Adviser. ...... The political organization of the States is reflected in the mining legis- lation, Johore being the only one having a comprehensive code. The mining enactments now in force, according to the High Commissioner for the Malay States, are as follows:

Jun 1, 1932

By W. D. Gould, A. Kapoor, K. Morin, P. Bédard

This paper presents the results of a research study that is being conducted by the Mine Effluents Program, Mining and Mineral Science Laboratory (MMSL), Natural Resources Canada aimed at evaluating biotechnology processes for the treatment of nitrogen compounds such as thiocyanide (CNS) and ammonia (NH4-N) which are present in gold mill effluents. A sequencing batch reactor (SBR) technology, commonly used for the biological treatment of municipal and industrial effluents, was used in this study. In the SBR process, the micro-organisms were able to degrade CNS to NH4-N and NH4-N to nitrate (NO3-N) at operating conditions of two 12 h treatment cycles per day, with pH maintained in the 7.4 to 7.6 range, and at room temperature (approximately 21°C) and also at 12 °C. The end products of CNS and NH4-N biological oxidation were NO3-N and sulphate (SO4) that are relatively non-toxic. Partial removal of NO3-N was achieved by biological denitrification reactions in the SBR process. The SBR process effluent was measured to be non-toxic to rainbow trout based on the 96 h acute toxicity test. The microbial consortium isolated from the SBR treating a simulated effluent was able to effectively oxidize CNS and NH4-N to NO3-N in water samples (under batch conditions) collected at three mine sites located in Quebec, the Northwest Territories, and Yukon.

Jan 1, 2004

By W. Kint

More than 10 years ago, one of MECS?s current partners KVT developed the so called SULFOX process for cleaning waste gases containing sulfuric compounds. In this Wet Acid Process (WAP) compounds such as SO2 and H2S, CS2, COS are oxidized over catalyst bed(s) to SO3 and finally sulfuric acid is formed. The individual plants are designed according the feed gas concentrations and customers requirements to keep the investment and operating costs as low as possible. MECS strongly believes the technology we propose will meet all your expectations. Thanks to our vast experience in the construction of sulfuric acid plants (MECS built over 800 sulfuric acid plants worldwide) we were able to design you a very reliable installation. MECS is offering the metallurgical industry, besides our conventional acid plant technology (for strong SO2) and our DynaWave? scrubbing technology (for very low SO2), a SULFOX wet acid plant (for the mid range SO2 concentrations) including an optional upstream DynaWave gas cleaning plant if required. See the figure below. Besides providing advanced technology, MECS is the only company who designs and manufactures its own key critical equipment. We manufacture our own catalyst, mist eliminators, acid distributors and coolers. Because of our in-depth technology knowledge, we understand the critical aspects necessary for making optimum equipment designs. With this combined supply of technology and key critical equipment, we can make a single overall guarantee second to none other in the world.

Jan 1, 2009

By Marcus A. Grossman

THE institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it," All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we should review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks.

Jan 1, 1946

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By I. L. Dillamore

I. L. Dillamore (University of Birmingham)—The different textures developed in various fcc metals have long awaited satisfactory explanation and it has now become clear that these differences are related to parallel differences in the deformation characteristics of the metals. Liu is correct, therefore, in seeking to account for the observed textures in terms of the flow mechanisms but I believe, for the reasons outlined below, that the particular interpretation of flow mechanisms proposed by Liu is open to substantial objections. By considering the forty-eight possible designations of the twelve octahedral slip systems found in fcc metals as distinct and separate deformation modes, Liu has fallen into the error of assuming that only positive glide dislocations associated with each system are present. In fact both positive and negative dislocations will be present and the only difference between for instance the systems B4 and B4' (in Liu's notation) is that under a stress of given sign the direction of motion of a dislocation is reversed on changing from B4 to B4'. For both orientations positive and negative dislocations will be present. In considering possible dislocation interactions it is, therefore, inadmissible to differentiate between R4 and R4' as Liu does. Liu considers those dislocation interactions which give the biggest reduction in energy to be the most favorable and neglects, on the grounds that they will form strong barriers to slip, interactions between dislocations with perpendicular Burgers vectors. Setting aside interactions between positive and negative dislocations of the same slip system, which must occur regardless of the combination of slip systems chosen, the biggest reduction in energy occurs for the Lomer-Cottrell interaction and it is Lomer-Cottrell barriers which are thought to provide the stronger dislocation obstacles. On the other hand the intersection of dislocations with perpendicular Burgers vectors is thought to be a low-energy process which contributes only a fairly small temperature-dependent part of the total work hardening. On this basis it seems doubtful whether the reduction in energy through possible dislocation interactions provides a reasonable criterion for choosing the operative slip systems. From the point of view of texture development it is unsatisfactory to ignore the slip rotations leading to an end position and to neglect to consider the stability of the chosen end point. It is also unsatisfactory to treat the two stress axes as interchangeable since, if the stress system is idealized as biaxial, one stress is compressive and the other is tensile. For the same reason the rotations of the two stress axes are not made compatible simply by assuming that the same slip directions are responsible for the rotations of the two stress axes. It is, in short, essential to treat the two stress axes as acting together on the same slip systems. Turning to the question of the difference between the copper-type and the brass-type texture, there now remains little doubt that the difference is attributable to differences in stacking-fault energy (y), as noted by Liu, but it is doubtful whether the temperature dependence of the texture in copper and in silver is due to increasing stacking-fault energy with increasing temperature. The results of Swann and Nutting42 cited by Liu were obtained in Cu-A1 alloys and the apparent increase in stacking-fault energy on raising the temperature may be influenced by short-range ordering. In pure metals such effects are absent and the only data available on the variation of y with temperature are those of Buhler et a1.43 for silver. They report a minimum at 200°C which does not fit the hypothesis put forward by Liu. It is much more likely that thermal activation of cross slip is important in determining which texture develops, as proposed by Dillamore and tors. These workers have proposed an explanation for the differences in observed texture among the fcc metals and the pole figures predicted consist of an orientation spread which is in better agreement with observation than the limited number of discrete orientations suggested by Liu. The theory of Dillamore and Roberts is also able to account for the differences between aluminum and copper which Liu still leaves unexplained. Y. C. Liu (author's veply)—The writer appreciates the interest of Dr. Dillamore, but must discuss some of his comments in order to avoid cross purposes. The phrase, "forty-eight slip systems," which appeared twice in the text—in the caption of Fig. 1 and the first paragraph in the Discussion—might unfortunately have led Dr. Dillamore to disagree

Jan 1, 1965

By William F. Boericke

CONSIDERABLE waste of oil and grease in lubricating motors and other machinery results from the use of bearings that are not totally enclosed. There is also the likelihood of damage to the bearing through the accidental introduction of grit or dust both in the oiling process and after, unless the cover is entirely dustproof. With the ordinary sleeve bearing that is only partly enclosed, it is generally easier for a careless attendant to cause trouble through neglect than with the ball bearing type, which from its design, must be totally enclosed to give effective service, and needs a minimum of attention. At one of the large mining companies which has taken a leading part in reducing unit costs and pioneering new developments in mining machinery, ball bearings have been gradually supplanting the conventional type of sleeve bearings on many of their motors, centrifugal pumps, and other machines in the mines. This innovation is not recent, as substitution of ball bearings on mine motors was first tried out by this company in 1909. Since then an increasing number of such bearings have been put in. They are now favored because of increased operating efficiency and reduction in lubrication costs.

Jan 1, 1926

By Milnor Roberts

WAR struck the mineral industry of Washington with cross currents that produced a peculiar result. The State's production of coal, industrial minerals, and metals for 1941, valued at $28,507,282, was increased in 1942 under war pressure to approximately $35.000,000. Meanwhile a tremendous demand had arisen for men to construct airfields and many other large projects for the Army and Navy in Washington and Alaska, and Government plants for the mineral industry costing $140,000,000 or more, as well as a call for employees in the U. S. Navy Yard at Bremerton, the sixty shipyards, the four Boeing airplane factories with many auxiliary shops, and hundreds of other plants turning out war materials. In spite of an influx of nearly 300,000 people, causing an increase of 17.1 percent in the population since 1940, according to the Census Bureau, the State clearly is still engaged in an unusual amount of war production in proportion to its population. A large proportion of the workers have been drawn from the mineral industry to the war plants, whether through motives of patriotism, high wages, or, in the Boeing plants at least, the glamour of the operation

Jan 1, 1944

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By Lloyd F, Arnold D. A, Hagan T. O

This paper investigates the problems that are encountered in mining at extreme depths. It looks into the rock mechanic aspects, especially the high stress levels that will occur, and the hazard of rockbursts. Furthermore, environmental problems are discussed, with refrigeration and reduction of neat loads being major methods of maintaining ,sorkable conditions. The paper concludes that it will be of tmost importance to have a planning team of Tne highest quality to ensure that conditions are maintained so that work can be carried out safely and under reasonable conditions.

Jan 1, 1986

By Y. Zhang, C. Zhou, M. Girman

Wireless technologies are increasingly being implemented in underground mines for various purposes such as communications, tracking, remote control, remote sensing, and environmental monitoring. However, the adoption comes with risks as common wireless systems, such as WiFi, Bluetooth, IWT (Innovative Wireless Technologies) wireless system, often operate in the unlicensed ISM (industrial, scientific, and medical) band. The shared nature of the ISM band can lead to interference among devices and consequently cause performance degradation and reliability issues. In this study, we developed two wireless communication evaluation boards as a tool to evaluate the performance and reliability of a wireless system with the presence of electromagnetic interferences (EMI) from other wireless systems in underground environments. We adjusted various parameters including signal power from adjacent frequency channels, noise power within the same channel, the movement of personnel, and communication packet size. Our findings indicate that, while the power of the EMI source plays a key role, the motion of personnel in the tunnel also has a strong impact on performance, and this impact increases as the power of EMI sources increases. In noisy environments, smaller packet sizes are preferable as they enhance the likelihood of successful transmission. High levels of interference or noise can lead to increased packet loss or error rates, potentially causing communication links to fail completely or become ineffective. The evaluation boards utilized in this study are based on a practical wireless transmission system deployed in a remote controller for a heavy mining machinery used in underground coal mines. The results and findings presented in this paper can aid in the design of wireless systems that are resilient to EMI in underground mining environments.

Feb 1, 2025

By Germán Alva, Camilo Ferreira, Rómulo Villegas, Franco Olcese

El siguiente documento presenta el caso de la realización de talleres participativos, voluntarios e inclusivos de consulta social con comunidades, centros poblados y ciudades del área de influencia directa e indirecta de Minera Yanacocha, en Cajamarca, Perú. El objetivo con estos talleres es conocer las percepciones y el sistema de creencias de la población con respecto a la minería y el impacto de estas creencias sobre la postura hacia la empresa, brindar información desmitificando mitos y midiendo la aceptación de la actividad minera.

Sep 30, 2022

By Barbara J. Arnold

A coal's size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.' s (formerly EPRI' S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By M. Ahlers, Horace Pops

Slip features and formation of stress-induced mm-tensite have been studied in single crystals of fl phase Cu-Zn alloys in the composition range between 43 and 48 at. pct Zn. A phenomenological analysis is presented in which the glide planes and directions that me associated with the inhomogeneous shear in the martensite phase are predicted from the experimentally determined habit planes and macroscopic shear directions. It is shozun that the resolved shew component of the applied stress on the secondary shew system is a very important factor governing the formation of stress-induced martensite. A comparison is made between martensitic phases that form spontaneously upon cooling and those phases that arise from deformation. THE ß phase in Cu-Zn alloys is unstable and may transform spontaneously by a martensitic transformation1-3 during cooling. Thermoelastic and burst-type spontaneous martensitic phases have been observed3 in the composition range between 38 and 42 at. pct Zn. Martensite forms in alloys containing more than 42 at. pct Zn only by cold work below a temperature denoted as Md.4 Thus, alloys near the equiatomic composition can undergo a stress-induced transformation upon cold work at room temperature. Although data have been obtained concerning the effect of temperature5 and composition4 on the deformation of polycrystalline Cu-Zn alloys, it is rather surprising that few detailed studies6-8 on 6 brass have been conducted for single crystals where the stresses acting on crystallographic planes can be determined. A thorough understanding of transformation mechanisms requires knowledge of the role of stress and plastic strain. With this objective in mind we have made an investigation of the stress-induced rnartensite transformation in single crystals of 0 brass in the composition range between 43 and 48 at. pct Zn. Particular emphasis is given to the morphology and crystallographic features and a comparison is made between stress-induced and spontaneous martensite. I) EXPERIMENTAL PROCEDURE Master alloys having nominal zinc contents of 43, 45, and 48 at. pct were prepared from spectroscop-ically pure metals (>99.999 pct) in sealed quartz tubes under a partial pressure of helium. These alloys were cut into several pieces and converted into small rods by melting in quartz tubes. Subsequently, single crystals were grown from the rods by the Bridgman technique and homogenized for 3 hr at 820°C. Lattice parameter measurements were made from stress- relieved filings. Compositions, as determined from the reported variation of lattice parameter with atomic percent zinc,' indicated a zinc loss of less than approximately 0.25 at. pct. The single crystals were electroturned using a phosphoric acid electrolyte into tensile specimens each with a center section of 1 mm diam and 1 cm gage length. Cylindrical specimens approximately 3 mm in diam and 10 mm long and spark-machined rectangular blocks approximately 3 by 3 by 10 mm were prepared for compression studies. These blocks were stress-relieved and electropolished to eliminate any stresses introduced by spark machining. Crystal orientations were determined to an accuracy of ±2 deg primarily from back-reflection Laue photographs, and sometimes by the rotating single-crystal method. Figs. 1 to 3 show the location of the tension and compression axes within unit stereographic triangles. All specimens were deformed plastically at room temperature using an Instron machine, the crosshead speed being 0.02 or 0.05 cm per min. A hard steel hemisphere was placed at the upper end of the compression samples to achieve uniaxial loading. Trace normals of slip markings and habit planes of strain-induced martensite were determined to an accuracy of ±4 deg from the rectangular blocks by a two-surface analysis and from cylindrical specimens by measuring the angle between the tensile (or compression) axis and the tangent to the surface trace for different rotations about the deformation axis. Slip

Jan 1, 1969

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

By L. H. Morris, M. Mordecai

The emission of firedamp from the strata surrounding active workings of longwall coal faces normally follows a cyclic pattern associated with the mining operations being carried out on the face. Mining a coal seam disturbs the uniform distribution of overburden weight such that the working is enveloped by a region of high stress, both above and below the seam, advancing with the coal face. There is a decrease in stress as the strata is relaxed following the passage of the face (1). The paper describes experimental results obtained during the initial investigations of a study intended to examine the permeability of samples of coal measure strata under various triaxial stress conditions. Several investigators have studied the effect of stress on the permeability of rock, usually in the field of oil reservoir engineering. Two general lines of approach are evident. One used by among others Fatt and Davies (2), McLatchie et a1 (31, Brace et al (4) and Gunther (5) was to subject a rock sample to hydrostatic pressure. Gas or water would be passed through a sealed core mounted inside a high pressure hydraulic bomb. The second approach, favoured by Wilhelmi and Somerton (6) and also by Gray et a1 (7) was to employ a so-called 'triaxial' state of stress. Here radial confining pressure and axial stress are applied independently. The permeability is measured in the direction of the axial load. With the exception of Gunther who tested coals and Brace et a1 who tested a granite, the rocks used have been sandstones with permeabilities generally appreciably higher than British coal measure rocks.

Jan 1, 1971

By J. Riefenberg

U.S. Bureau of Mines (USBM) researchers are developing a personal computer-based hazard mapping system for use in underground coal mines. Hazard mapping is rapidly gaining interest as delineating areas of possible instability is becoming more complex. The development of a hazard map is based on the consensus that combined effects of local and regional stresses, roof, floor, and rib quality, geology, faulting, presence of ground water, etc., all contribute to stability of the ground. In order to demonstrate the concept, a hazard map was developed that combined stresses anticipated to occur in a multiseam setting using numerical modeling, and the newly developed Coal Mine Roof Rating (CMRR) where roof quality ratings in untested areas were modeled using geostatistical methods. Ten borescope readings from an underground mine were used to compute CMRR's for the geostatistical analysis. CMRR's for the mine ranged from 57 to 77, and are considered in the moderate to strong range. A hazard map was developed by combining the stress effects of interseam mining, scaled to weigh equally with CMRR's, and CMRR geostatistical analysis results. This hazard map demonstrates a synergistic effect between the mining-induced stress fields and the roof quality ratings, indicating, as expected, a greater hazard index in areas of high stress and lesser roof quality.

Jan 1, 1994