Search Documents

By Thomas L. Mell

Continuous processing plants handling liquids have achieved a high degree of centralized automatic control. Many chemical plants are operated from one room, with automatic control of the various process flow rates. These plants know from experience that automatic control can produce higher through-put, better uniformity of product, decreased operating costs and reduction of storage capacity, Plants which process materials in the form of bulk solids have not been able to use control to as great an extent, primarily due to the lack of measuring equipment capable of providing the same types of continuous automatic control available with liquid flow meters. This paper will describe a scale for measuring flows of bulk materials on conveyor belts which is particularly adaptable to remote centralized instrumentation and automatic control, and will also describe some typical control applications. Fig. 1 illustrates the basic method of measurement of this scale. A conveyor belt idler is supported on a rigid carriage which in turn is mounted in two anti- friction bearings on the conveyor stringers. The pivoted carriage is prevented from rotating about the pivot shaft by an electric strain gauge load cell connected between the carriage and a cross support. Increasing load on the conveyor belt increases the moment of the carriage frame about the pivot shaft, and proportionally increases the tension in the load cell. The belt speed is measured by a conventional d. c. tachometer generator driven from a pulley, usually on the return belt. The speed signal from the tachometer generator and the load signal from the load cell are combined to produce a signal proportional to the flow rate of material in tons per hour, or lbs. per foot, or equivalent units, It will be important to remember, in considering various control applications, that the flow rate of material on the belt is composed of these two component signals, namely the weight of material and the speed at which it is moving. The feed rate is then indicated and recorded by a self-balancing potentiometer of the type used for measuring temperature by means of thermocouples. These instruments may also be equipped with integrating mechanisms reading the totalized tonnage over a period of time.

Jan 1, 1958

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By D. C. Treilhard

After a brief history of the mining and smelting operations of Kilembe Mines Limited, this paper outlines the smelter layout and describes . the. daily operations at the Jinja plant. Particular attention 1s paid to the details of the furnace and converter operation. A subsequent section of the paper deals with the significant developments in plant metallurgical practice, covering both smelting and converting.

Jan 1, 1966

The words ""Uncertainty"" and ""Risk"" pervade every discussion about mining exploration and investment. Perhaps these terms are subjectively understood by industry professionals, but objective portrayal of these concepts outside the industry is a woefully undeveloped science. This paper addresses current industry understanding and practice regarding quantitative risk assessment techniques, and provides examples of the application of three of these techniques. Probabilistic techniques for financial risk assessment are valuable adjuncts to conventional financial analysis, and address a range of issues not assessable by any other means. The value of whole-of-project probabilistic risk assessment is currently debatable for decision-making purposes, but is seen as important as a mechanism to focus attention to the critical issues that ultimately impact on project success. The dissection of project capital into risk and non-risk components provides valuable insights into risk characteristics not readily quantifiable in any other way. This technique also provides a framework for more objective ""what if?"" scenario evaluation and for the capital structure of resource projects. Finally, mechanisms for the valuation of undeveloped reserves are examined, and guidelines suggested. The importance of reliability in production cost estimates is highlighted and the impact of early development on reserve valuations is discussed. The importance of economics throughout all stages of the evaluation process is fundamental.

Jan 1, 1994

By W. A. SLOAN, G. L. Oldright, J. D. Sullivan, E. K. PRYOR, A. F. HALLET, R. S. Dean, S. L. BROWN, F. S. Wartman, A. J. Thompson

Lack of sufficient publication funds has resulted in the accumulation of considerable unpublished experimental work on copper metallurgy by the Bureau staff . The present report gives extended abstracts of this work , as well as a discussion of the best direction for future efforts . The experimental work reported in this series of papers was done in cooperation with the University of Arizona , Tucson , Ariz . The investigations covered in the third , fifth , and seventh papers were done under the direction of G. L. Oldright and the remainder under the direction of V. H. Gottschalk .

May 1, 1934

By G. McIsaac

"This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone’s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place.Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. “Whatif” scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan."

Jan 1, 2005

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005

By Ramsden AR, French DH

The limited contrast range of conventional black and white imaging does not enable full use to be made of the dynamic range of the video signal obtained from a scanning electron microscope or microprobe. The use of false colour substantially increases the information that can be derived from such images enabling relationships to be displayed that cannot be observed in black and white. This capability is now used extensively in combination with quantitative electron microprobe analysis as a research tool for ore characterization and host rocks studies related to minerals exploration in the CSIRO Division of Exploration Geoscience.

Jan 1, 1989

The Newmont Waihi Operations are centred on the Martha mine at Waihi, New Zealand. The mine has produced over 6.6 million ounces of gold from both openpit and underground sources since operations began in 1878. The current open pit operations commenced in 1988 and in the year to 30 June 2002 produced 129,790 ounces of gold at a cash cost of USD122 per ounce. This paper provides an overview of current operations and future directions.

Jan 1, 2002

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By Ken Mathers, Tom Conley, Jim Rozek

The Melbourne City Link Tunnels have been constructed through a BOOT process, the largest undertaking in Australia to date. Tolling commenced on the 1.6 kilometer Domain tunnel in April 2000, and the 3.4 kilometer Burnley tunnel December 2000. The project was delivered by design construct contracting and under ISO 9000. There were a number of major challenges in completing the tunnels, including much higher than expected groundwater infiltration, hydrostatic pressures greater than 6 bar, and unique design and construction applications required to prepare the tunnels for service. This paper covers the end play and final delivery of the tunnels.

Jan 1, 2001

By Wetzeil N

High ambient temperatures combined with high surface humidity in the north of Australia and, in particular, the northern areas of the Northern Territory can make underground workplaces relatively inhospitable at certain times of the year. . Woodcutters' silver/lead/zinc mine, situated some 80 km south of Darwin, would be the most northerly underground operation of any significance in Australia. As such, during the build up to the wet season, it has a particular problem of ventilating a deep underground mine with already high dry and wet bulb temperatures at the surface. The Mine Management Act and Regulations mention only that workplaces shall be 'in a fit state for a person to work in or occupy'. Woodcutters therefore set in progress a Heat Stress Program to endeavour to set standards which would be more measurable and justifiable. The aim of the program was to compile a record of ambient atmospheric conditions in the working areas such that areas and/or work activities generating high ambient temperatures and humidities could be identified, quantified and qualified. Once the analysis stage of this program was completed, Woodcutters compiled a set of recommendations for the continued monitoring for, and control of, heat stress conditions to ensure that no underground employee was placed at risk from 'heat stress'. These recommendations are discussed in this paper.

Jan 1, 1994

By K. Morsi

Titanium-titanium boride whisker (TiBw) composites are emerging as strong candidate materials for advanced applications within the automotive, aerospace and defense industries. Although increasing TiBw volume fraction improves the specific stiffness and wear resistance of titanium, it is usually on the expense of fracture toughness and ductility especially at increased volume fractions of reinforcements where whiskers interlock. This research addresses strategies for microstructural design that may overcome these shortcomings, by generating titanium composites that are locally reinforced with TiBw through in-situ reaction in segregated regions of the microstructure and separated by ductile Ti matrix. The effect of varying composite reinforcement particle sizes (i.e. size of the reinforced regions) on the pressure-less sintering of these dual matrix composites is discussed. Electric current activation was also used to generate high density dual matrix composites and a new simultaneous imaging and modulus mapping technique was used to characterize these unique microstructures.

Jan 1, 2008

By B. M. O'Harra

The residues resulting from the retort distillation of zinc ores have from 40 to 75 per cent of the weight of the original ore and contain from 5 to 15 per cent zinc . A rough estimate indicates that approximately 450,000 tons of residues are produced annually in the United States , containing about 36,000 tons of zinc . Besides the current production of residues there are at many smelter sites large accumulations from past operations which are available for treatment if this can be done profitably . In addition to their zinc content the residues contain much unconsumed coal , which has been carbonized during the distillation process , and those from most western ores also contain lead and silver . In this paper is summarized the information obtained in a survey , recently made by the Bureau of Mines , in cooperation with the Missouri School of Mines and Metallurgy , of processes which are in use or which have been suggested for the treatment of retort residues . The complete report of the survey is to be published as a Technical Paper of the Bureau of Mines .

Apr 1, 1923

By Estefania Aramayo, Jhon Silva, Todor Petrov

Blasting is one of the most critical activities in a mining operation. Nowadays, many quarries have to follow a considerable quantity of environmental restrictions that drive the need to improve the conceptualization, design, procedures, and execution of the blast to comply with all regulations. Airblast is one of the variables required to control when blasting. Airblast is an unwanted side effect of blasting. Airblast is defined as an airborne shock wave resulting from the detonation of explosives. Traditional methodologies used for assessing the overpressure produced by the airblast are based on empirical approximations that require the collection of a series of produced airblasts before they can be used as a predicting tool. Once the data is available, regression analysis methodologies are used to find the constants of empirical laws that, in most cases, establish the relationship between the distance and the weight of explosives used in the shot (scaled distances laws). If using the traditional methodologies, the quality, and representativity of the scaled law established for a particular project are determined in terms of the correlation coefficient; in most cases, the models and their use as a predicting tool are questionable (very low correlation values).

Feb 6, 2023

By A. J. Meir, Paul G. Schmidt

"We present a novel approach to the mathematical analysis and computational simulation of fully three-dimensional, nonlinear, viscous, incompressible MHD flow in complex configurations involving several liquid and solid conductors. Such configurations arise in numerous metallurgical processes. Employing the current density rather than the magnetic field as the primary electromagnetic variable, it is possible to avoid artificial or highly idealized boundary conditions for electric and magnetic fields and to account exactly for the electromagnetic interaction of the flow region with the surrounding space. In addition, the approach lends itself naturally to finite-element based discretization techniques. As an application, we simulate the stationary flow of an electrically conducting fluid around a solid spherical particle of arbitrary conductivity, in the presence of crossed uniform electric and magnetic fields, and compute the Lorentz, pressure, and viscous forces exerted on the particle. This problem arises in connection with the electromagnetic filtration (purification) of molten metals before the casting stage.IntroductionNumerous metallurgical processes are governed by MHD effects resulting from the macroscopic interaction of liquid metals with applied or induced currents, electric and magnetic fields. Frequently these effects are technologically exploited in order to drive or to control the flow of metallic melts. Typical examples include the electromagnetic stirring of molten metals before the casting stage [1]; electromagnetic turbulence control in induction furnaces [2]; electromagnetic damping of buoyancy-driven flow during solidification [3]; and the electromagnetic shaping of ingots in continuous casting [4]."

Jan 1, 1999

By C. L. Kosmoski, B. M. Eiter, B. P. Connor

"In the recent past, the mining industry has witnessed a substantial increase in the numbers of fatalities occurring at metal and nonmetal mine sites, but it is unclear why this is occurring. One possible explanation is that workers struggle with identifying worksite hazards and accurately assessing the associated risk. The purpose of this research was to explore this possibility within the mining industry and to more fully understand stone, sand and gravel (SSG) mine workers’ thoughts, understandings and perceptions of worksite hazards and risks. Eight mine workers were interviewed and asked to identify common hazards they come across when doing their jobs and to then discuss their perceptions of the risks associated with those identified hazards. The results of this exploratory study indicate the importance of workers’ jobrelated experience as it applies to hazard identification and risk perception, particularly their knowledge of or familiarity with a task, whether or not they had personal control over that task, and the frequency with which they perform that task. IntroductionAccording to the U.S. Mine Safety and Health Administration (MSHA, 2015a), 37 mine workers were fatally injured in accidents at metal and nonmetal mine sites between October 2013 and January 2015, following a record low of 16 in 2012 and in 2011. In 2014 alone, 29 mine workers were fatally injured at a metal or nonmetal mine site, and 52 percent of these fatalities occurred at a surface stone, sand or gravel (SSG) mine. In January 2015, Joseph A. Main, Assistant Secretary of Labor for Mine Safety and Health wrote to stakeholders in the metal and nonmetal mining community and identified several areas where improvement was necessary to promote the health and safety of mine workers. One area identified was an increased focus on “daily and effective workplace exams to find and fix hazards” (MSHA, 2015b).Hazard detection is challenging in the mining industry, despite the existence of regulation. Mining is a major undertaking involving the use of complex heavy machinery, equipment and processes as well as numerous and diverse worker activities that take place in a dynamic, challenging environment (Scharf et al., 2001). In other industries that are similarly dynamic and unpredictable, such as the construction industry, a large proportion of hazards go undetected (Carter and Smith, 2006). It is critical that miners are able to both recognize worksite hazards and accurately assess the risk associated with the hazards, because their health and safety depend on their deciding whether and how to remove hazards and mitigate risks."

Nov 1, 2016

By H. Kinilakodi

The authors previously had developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the Safe Performance Index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency, or MSHA in recognizing and addressing emerging problems with actions that may have been able to prevent high-risk conditions, the fatality, and/or other serious injuries. The approach would have given scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012

By A. Osouli, B. Moradi Bajestani

"Increase in permeability of rock mass is vital for both petroleum and geothermal applications. Hydraulic fracturing is a common method to create and increase the permeability for production. Due to the complexity of fracture propagation in a naturally fractured medium, understanding the interaction between hydraulic fracture (HF) and natural fracture (NF) is of great importance to optimize the fracturing process. The possibility of interaction between HF and NF is partly a function of orientation. Various scenarios are predictable for hydraulic fracture regarding the intersection with NF such as being arrested by NF, crossing NF or crossing the fissure while injecting water into it. Different parameters such as geomechanical and geometrical properties of surrounding rock mass, the operational parameters such as injection rate and the angle between created hydraulic fracture and natural fracture (approach angle) can affect the result of hydraulic fracture and natural fracture intersection. In this paper, using a series of flow-coupled Distinct Fracture Network (DFN) simulations, hydraulic fractures were analyzed to investigate the influence of the aforementioned parameters on the hydraulic fracture propagating. Results show that the most significant parameters affecting the interaction of natural and hydraulic fracture are orientation of the intersection as well as injection rate. The interaction and fracture propagation in NF and HF intersections are also studied and discussed in detail.INTRODUCTIONThe hydraulic fracture technology has substantially changed the oil, gas and geothermal industries. With the help of this technology, extraction of fossil resources from tight shale reservoirs will be economical, feasible and sustainable. Due to presence of massive oil and gas trapped in these reservoirs, this technology has been the center of attention for the past 40 years (King, 2012). Hydraulic fracturing is the process in which high pressure water is pumped into shale unconventional reservoirs with low to ultralow permeabilities. With this process paths are created in these mediums for delivering oil and gas to horizontal wellbore and increase the surrounding rock medium permeability. Economical and sustainable stimulation of these tight reservoirs is highly dependable on our understanding in regard to fracture propagation in the highly complex rock medium. Hydraulic fracturing process in rock mediums with preexisting natural fractures is more complex because of the high possibility of Hydraulic Fracture (HF) being arrested or deviated by Natural Fracture (NF). Also, HF and NF intersection can influence the required pumping pressure, injection rate, the outcome of horizontal wellbore and the affected geological underground zones. Since the 1950s, numerous studies have been conducted to predict and plan fracture propagation with the help of modeling and simulation methods. Having a thorough and accurate prediction of fracturing process will not only prevent stimulation of unwanted geological zones or pollution of aquifers, but also will improve the efficiency of the fracturing process. Previously, several studies have been conducted in order to investigate and analyze the interaction of hydraulic fracture and natural fracture (Cottrell, Hosseinpour, & Dershowitz, 2013; Doe, Lacazette, Dershowitz, & Knitter, 2013; Shakib, 2013; Zhang & Jeffrey, 2006)."

Jan 1, 2015

La importancia del desarrollo de centros mineros en las diversas regiones del país, no solo responde al redescubrimiento de algunos yacimientos mineros abandonados, sino a la permanencia de dicha actividad, a través de la reactualización de sus elementos corporativos y el uso de sus instalaciones. Por tal motivo, el objetivo del presente trabajo busca repotenciar la producción de dicha minera -en tanto mantenga sus labores y mejore su método de explotación-, asi como contribuya al desarrollo económico-social de la provincia Grau y Ccochasayguas. La provincia de Grau, ubicada en Apurímac mantiene un tradición minera que se remonta al periodo colonial, donde funcionaron dos intendencias mineras: una en Haquira, que vigila las explotaciones auríferas de Osoollo, Anyo y Patario, y la otra, en Curpahuasi. Posteriormente en 1890, un minero apellidado Rodriguez, redescubrió el mineral de Ccochasayguas para cuya explotación Samanez, Bottger y Letona de Abancay formaron una sociedad, y luego con la intervención de Amadeo de Piérola, se transformó en La Cotabambas Auraria. Después de una serie de altibajos, Ccochasayguas logró posicionarse como la mina más importante de oro que tuvo el Perú. De otro lado, en 1931, la Compañía Exploradora Cotabambas instaló en Progreso una Planta hidroeléctrica, facilitando la importación de la perforación mécanica en las minas, con compresoras y perforadora. La oficina de Progreso abarca los distritos de Cotabambas, Tambobamba, Haquira, Huayllati, Mamara, Ourpahuasi y Vilcabamba, encontrándose en esta zona minas de cobre, plomo, plata y oro. Empero la labor de la minera Ccochasayguas se detuvo debido algunos inconvenientes económicas, eliminando actividades de apoyo a dicha comunidad. La rehabilitación económica de Grau, depende de que nuevamente puedan organizarse trabajos mineros, así como se reutilizen dichos depósitos mineros para brindar trabajo remunerado a la población obrera de Grau, y conseguir a favor del Estado, una mayor producción exportable de metales.

Jul 20, 1957