Search Documents

By Chas. F. Jackson

The annual reports of the supervising engineering of the nine sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those current activities that contribute most to problems of present concern are emphasized, investigations of less immediate importance being recessed, if necessary.

Jan 1, 1940

By Chas. F. Jackson

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled in tie following pages and constitute the annual report of the division. In planning activities, the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those current activities that contribute most to problem of present concern are emphasized, investigations of less immediate importance being recessed, if necessary.

Jan 1, 1940

By Jonisha P. Pollard, F. Nasarwanji, Lydia M. Kocher

This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1000 full-time employees, which is nearly double the rate of the next highest affected body part, the back.

Feb 24, 2022

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By Doug Harding

The Metropolitan St. Louis Water District’s Project Clear is a 28-year program targeting wastewater capacity throughout St. Louis, MO. The extensive program includes the Jefferson Barracks Tunnel, running parallel to the Mississippi River at 2 m ID and 5,400 m long. A rebuilt Robbins Main Beam TBM began boring but hit challenging conditions about 2,400 m in, including water inflows. A larger 4.1 m Robbins Main Beam machine will complete the remaining 3,050 m in limestone, dolomite, and shale. The TBM will utilize a high-powered, high breakout torque cutterhead along with enhanced 360-degree probing & grouting capabilities to detect any karst formations.

Dec 1, 2022

By Steven Townend

Mining-related activities have been known to create a challenging operating environment for mining companies located in close proximity to communities. Issues such as noise, vibrations from mining operations, land use and emissions are often a concern for community residents. In order to develop good community relationships it is necessary to take a proactive approach. This paper documents this approach and also deals with the social implications for Vale associated with mining activities in the heart of the community of Copper Cliff, Ontario, Canada.

May 1, 2011

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world's phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001

By W. W. Scott

Measurements of the absolute value of electromagnetic noise and attenuation along a hoist rope were made in an operating hard-rock mine, Lucky Friday Mine, located near Wallace, Idaho. Spectra of electromagnetic noise generated by various pieces of equipment, spectra of specific noise signals at various depths, and noise and attenuation on the 4250 foot (1295 meter) hoist, were measured. Three techniques were used to make the measurements. First, noise was measured over the entire electromagnetic spectrum of interest for brief time periods. Data were recorded using broadband analog magnetic tape for later transformation to spectral plots. Second, noise amplitudes were recorded at several discrete frequencies for a sufficient amount of time to provide data for amplitude probability distributions. A third technique gave attenuation data through the direct measurement of field strength at various depths. The specific measured results are given in a number of spectral plots, amplitude probability distribution plots and amplitude curves as a function of depth.

Jan 1, 1974

By Frederick A. Subosits

The Lithium Corporation of America's Hallman-Beam spodumene-pegmatite open pit mine is located in the Kings Mountain area of North Carolina. Figure 1. Presently this area of North Carolina is the lithium center of the U.S., if not of the whole world. The Lithium Corporation mine was started in 1968 and now covers 61,000m2 (15 acres) with projected are reserves in excess of 20 years. Lithium occurs at the Hallman-Beam property in a mineral known as spodumene (LiAlSi2O6), a lithium aluminum silicate. The run-of-mine are averages 1.43 Li2O. Figure 2 of the general Mining Division flow sheet follows the concentration of the Li2O to 5.5% and also lists the various by-products that are sold commercially. The unique properties of lithium have led to many commercial applications, some of these including lubricating greases, ceramics, glasses, glazes, welding fluxes, aluminum reduction cells, dehumidifying and air-conditioning equipment, sanitizers, polymerization catalysts, batteries, and pharmaceuticals. (3) (5)

Jan 1, 1978

By W. D. Monaghan

One of the major ignition sources of fires and explosions in underground U.S. coal mines is flame cutting and welding. On May 20, 2006, a flame-cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On Jan. 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame-cutting and welding operation at the Loveridge Mine caused a fire that required sealing the mine for an extended period. On March 19, 1992, an explosion initiated by welding at the Blacksville No. 1 Mine resulted in four fatalities. These examples of mine incidents demonstrate the need to conduct research to develop best practices for safely conducting flame cutting and welding in underground coal mines. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame-cutting and welding operations to determine the root causes of these types of incidents. The methodology included interviewing mining personnel who perform flame-cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations. In addition, MSHA reports of investigations and accidents statistics were analyzed. The findings were used to identify and compare differences between flame-cutting and welding practices and techniques in small and large mines, eastern and western mines, low-seam and high-seam mines, room-and-pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices were developed to reduce the number of ?res and explosions caused by flame cutting and welding. This paper provides a summary of this research.

Jun 1, 2010

By Raymond Dallaire

The Humphrey's spiral is a static gravity separation device which cannot be adjusted to match short-term variations that occur in the feed. Any disturbance in the feed grade, per cent solids or flow rate affects substantially the recovery and grade of concentrate. Such variations must be minimized in order to maintain the desired rate of production and quality of the product for which the installation has been designed. A study has been performed in which the foregoing assertions were quantified. The feed grade, per cent solids, flow rate and particle size were varied independently. Ore from Carol Lake, Nfld., was used throughout the experiments. This consisted of specular hematite and magnetite in a silica gangue.

Jan 1, 1978

As 1979 drew to a close, it was obvious that China would have another good year with output of most industrial products at 3-9% above levels attained in 1978. Most increases were registered on the basis of maximum utilization of existing capacities and nationalization of procedures and methods. There were also distinct improvements in the quality and variety of products. Coal output probably surpassed the 650-Mt level in 1979. Steel output was expected to reach the 35-Mt level, an increase of nearly 10% over 1978. Based on the vast amount of housing and road and project construction, cement production more than likely surpassed 70 Mt. The nonferrous base metal industries improved somewhat in 1978, but actual output levels in recent years may have been a little higher than previously estimated by the outside world. Stagnate world demand slowed growth in the "export metals" sector. Minerals like magnesite and talc were produced at tonnages much larger than previously thought, with gold also falling into this category. Sulfur and pyrite production are still short, although a big pyrite mine was being brought into production. Barite out-put was reportedly up and fluorspar output held its own. Westerners generally concede that difficulties in transportation and power supply are holding back mineral production. Throughout 1979, basic construction continued on the majority of projects started by the Chinese and those few foreign projects contracted before the adjustment of industrial priorities. Foreign Ventures Perspective The foreign connection looms large in China's plan for modernization. In effect, it is an extension of what China wants to do in terms of "walking on two legs"-that is, develop what can be done locally to the fullest extent, then rely on international technology to move into the bigger and more complicated projects. Foreign projects are designed to complement domestic projects rather than replace them. Many foreign projects were started or continued by the Chinese in 1979. Building the necessary infrastructure for the projects is usually a Chinese endeavor and requires Chinese technicians and money. In areas with a strong economic base, this activity proceeds without foreign aid. In other areas, added funds are requested. Foreign funds can come in many forms-equipment technology, low interest loans, equity capital, advance-of-funds on the basis of future delivery in kind, and joint venture money. The Chinese are exploring all these avenues, with the strategy of minimizing foreign exchange needs for individual projects. They feel very uncomfortable with high interest rates, even though interest can be treated as operating ex¬pense rather than capital expense. Then there's the question of rights. Will Chinese sovereignty be affected? Can foreigners own land, in addition

Jan 3, 1980

By G. L. Hundley, D. N. Nilsen

The U.S. Department of Energy investigated the use of liquid-emulsion membranes (LEM) for the selective removal and recovery of metals such as copper and zinc from mine waste waters. This investigation included field tests of a mobile, pilot plant-scale, continuous-flow LEM system. The system was tested at copper mines with solutions containing from 100 to 1,400 ppm Cu, and at a zinc mine with a solution containing 115 ppm Zn. Typical results from the copper tests were >90% copper recovery, and zinc extraction from waste water also was typically>90%. Although all of these waste waters contained high impurity levels, pure products were produced. On several of these field tests, integrated systems were tested that resulted in recovery of metal by-products, selectiv~ precipitation of iron, and polishing to reach discharge targets for essentially all of the contained metals. In addition, some results are included from laboratory-scale tests.

Jan 1, 2000

By Susumu Ukita

We have developed first a conveyor belt for transporting large lumps, i.e. Rock Belt successfully, in June 1976. The First Rock Belt had been delivered to Myodani site of Kobe City Developing Board in Japan, and its' successful operation has attract keen interests in customers from over the world as well as Japan. However, this First Rock Belt was removed in arch '81, viewing it has satisfactory expired its service life of about five-year, and also original location of this belt become to be far from the site due to long-years earth collecting work. Taking this opportunity, we introduce the Second Rock Belt applied for Rock Belt Loader as ell as three types of application of our Rock Belt working for rationalization of quarry of major company in Japan, and, view the prospect of Rock Belt:

Jan 1, 1981

By Jorgen Elbrond

Shovels, trucks and repair bays for the trucks each play their role in the capacity of an open pit operation. It is therefore convenient to have a procedure for the capacity calculation which takes all 3 factors into consideration in a comprehensive manner. This can be done by means of a cycle model, earlier developed for the shovel-dumper circuits, when the repair facility with its number of repair bays is added as a superimposed service system, which the trucks visit at certain specified intervals. The calculation model transforms the mechanical availability of the trucks into their operational availability. The system's capacity in truckloads per shift and the trucks' operational availability of certain combinations of shovels, trucks and repair bays are shown.

Jan 1, 1981

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt.

Feb 1, 2020

By Ethan Steward, Kyle Perry

Blast resistant structural design continues to be a research area of major concern for governments around the world due to explosive threats from both state and non-state actors. Glass and aluminum curtain wall systems are commonly used to clad the exterior of government and commercial structures, allowing light into the building, regulating the interior environment, and providing an aesthetically pleasing exterior. These systems are likely to fail when exposed to sudden, high-pressure events such as the purposeful or accidental detonation of explosives. Engineers have designed blast resistant curtain walls and structural elements to reduce the likelihood and severity of failure, but the design tools and testing mechanisms commonly used in the process may not accurately model or simulate actual blast conditions at all ranges. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one face of the target. Shock is applied evenly and immediately across the entire impacted surface. However, the source of real-life blasts is often very close to the target structure, and the assumption of far-field planar shock does not always apply. Mid-field blasts exhibit qualities different from those assumed about far-field shocks, specifically a hemispherical shock that produces different peak pressures, impulse curves, oblique reflections, and Mach stems across a target. This paper will examine mid-field shock effects from scaled distances of 2.5 to 4 13 (6.3 to 10.1 13) on a tall, scaled target by measuring reflected and incident pressure, impulse, and shock velocity across the target. Results will be compared to theoretical blast parameter equations and empirical data used by the industry. Possible effects of mid-field blasts on structures and further research ideas will be suggested.

Jan 21, 2025

By Gustavo Fierro

Se plantea un enfoque de dimensionamiento de coberturas para cierre de minas, considerando los criterios de estabilidad física, química y biológica a largo plazo. El desafío de una visión integral de solución a este problema se enfoca en proveer soluciones cuantificables que aseguren el comportamiento a largo plazo de la cobertura, de modo tal que se pase de una solución cualitativa a una cuantitativa. Para ello, se emplea el estado del arte en múltiples disciplinas, que si bien en las dos últimas décadas han dejado información valiosa, hasta ahora no estaba orientada a la visión integral del problema.

Sep 20, 2019

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

By David N/A Doucet, Colter N/A Angell, William N/A Joa, Kyle N/A Wagner, Catherine N/A Johnson, Marty N/A Langenderfer

The Kingery-Bulmash (K-B) equations are a widely accepted means of predicting air-blast parameters from surface explosive detonations. The parameters predicted from these calculations include incident and reflected pressure, time of arrival, shock front velocity, incident impulse, reflected impulse, and positive phase duration. K-B calculations are based on curve fitting of experimental data and can be used to predict air-blast parameters for explosive weights from less than 1 kg (2.2 pounds) up to 400,000 kg (440.9 US Tons), and ranges of 0.05 to 40 meters (1.9 inches to 131.2 feet). The K-B equations can also determine the parameters for multiple explosive types using scaled distances and relative equivalency to TNT. An experiment was designed to demonstrate if the measured results for incident pressure, time of arrival, shock front velocity, incident impulse, and positive phase duration equal the expected results reported for the detonation of a small quantity of explosive determined by the K-B Calculator. Three surface-detonated 300-gram (0.66 pound) hemispherical charges of Composition C-4 were observed via high-speed imaging and hydrostatic pressure monitoring. The hydrostatic pressure generated from each charge was measured via piezoelectric pressure transducers at a scaled distance of 10 from the charge epicenter, and at elevations of 0.30, 0.61, and 1.22 meters (1, 2, and 4 feet) above ground level. Variances in experimental values from the K-B predicted values were recorded for each measured blast parameter. Time of arrival, which was redundantly confirmed through high-speed imaging analysis and hydrostatic pressure monitoring, showed the highest deviation from the predicted values at more than double the K-B predicted value. This report compares the observed blast parameters from the test series with the expected blast parameters from the Kingery-Bulmash Blast Parameter Calculator. Differences between the experimental and predicted values are reconciled through analysis and discussion of testing conditions, instrumentation setup, and scaling methods.

Jan 1, 2019