Search Documents

By Paulo von Krüger

Nas condições adversas do mercado atual, aliadas à exacerbada competição é uma questão de sobrevivência a otimização de resultados. Para tal é imprescindível que os principais insumos, particularmente os mais gravosos sejam criteriosamente selecionados. Os eletrodos de grafite estão entre os itens principais na operação dos fornos elétricos a arco, tanto do ponto de vista técnico, quanto econômico e a escolha correta deste insumo deve contemplar aqueles dois enfoques. Esta escolha se faz dentre as diversas classes, disponibilizadas no mercado: RP, HP, SHP, UHP. O que se pretende no presente trabalho é sugerir uma metodologia que, contemplando o elenco de parâmetros influentes, permita fazer a escolha correta do eletrodo, dentro daquelas classes, tanto sob o enfoque técnico, quanto econômico.

Aug 17, 2017

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross-section within each rock layer; i.e., the profile inclination across each layer tends to be constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties, and factor of safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e., the planar profiles exhibiting the same FoS) up to 8° depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Feb 9, 2022

By Gary L. Hundley

As part of the U.S. Bureau of Mines program to reduce the Nation's reliance on foreign supplies for critical metals, a procedure was devised to separate and recover critical metals from mixed and contaminated super alloy scrap. The process uses both pyrometallurgical and hydrometallurgical methods to treat the scrap. The mixed scrap is converted to a matte containing 4 to 7 pct S by adding S directly to the molten metal. This matte is then granulated and ground to a minus 35-mesh particle size and leached with an HCI-CI2 solution. This process takes essentially all the Ni, Co, Cr, Fe, AI, and Mo into solution in a 3-h leach, leaving W, Ta, Ti, and Nb (Cb) in the residue. The Mo is recovered from the chloride leach solution by solvent extraction, and the Cr and Fe are recovered together by precipitation. The Ni and Co can be recovered individually by an existing solvent extraction-electrowinning process. The W is recovered by a caustic leach of oxidized Cl2 leach residue.

Jan 1, 2010

By Roberto Vargas

"El presente Trabajo de Investigación, tiene por objeto describir la tecnología, la operación del Proceso en la Planta que implementa dicha tecnología así como los resultados obtenidos en dicho Proceso y aplicaciones de la tecnología a otros tipos de concentrados de cobre (Enargita). "

Sep 1, 2017

By Maria Amélia Martins

Os aços inoxidáveis duplex (AID) possuem uma estrutura austeno-ferrítica de aproximadamente 50% de cada fase, tal característica confere aos AID propriedades mecânicas superiores aos aços inoxidáveis ferríticos e austeníticos e elevada resistência à corrosão. Esses aços possuem uma adição significativa de elementos de liga, que são os responsáveis pelo correto balanceamento das fases e asseguram as propriedades desejadas. Outro parâmetro importante para assegurar as propriedades desejadas é o processamento termomecânico. Sendo assim, este trabalho avaliou a influência de diferentes temperaturas de tratamento térmico de recozimento nas frações de fases primárias (ferrita e austenita) e nas propriedades mecânicas de dois AID (UNS S32304 e UNS S31803). Os tratamentos térmicos de recozimento foram realizados em cinco temperaturas diferentes com tempo de encharque fixo seguido de um resfriamento rápido. A quantificação das fases primárias foi realizada através de microscopia óptica (MO) e as propriedades mecânicas avaliadas em um ensaio de tração uniaxial. As frações de fases primárias medidas indicam que com o aumento da temperatura de recozimento há aumento na fração de ferrita e a temperatura onde a microestrutura é mais aproxima de 50% de ferrita e 50% de austenita foi em 1020°C em ambos os AID. Além disso, observou-se que com o aumento da temperatura e, consequentemente da fração de ferrita, houve uma redução no limite de resistência nos dois AID deste estudo.

Aug 17, 2017

The number of railroad coal cars (open top hoppers), dominated rail car orders and deliveries in 1975 according to announcements made February 11, by the Association of American Railroads and the American Railway Car Institute. Acting to keep ahead of increased coal production, the railroads installed 21,748 new coal cars in 1975, the most since 1957. The 1975 installation resulted in a net increase of 6,560 coal cars and an overall gain of 4.5 percent in the total capacity of the hopper car fleet. With most of the new coal cars going into unit train service --where car utilization is greatest --the railroads actual coal-carrying capacity was increased far more than 4.5 percent. The AAR estimated that unit train operations now move 50 percent of all rail-hauled coal compared to only 42 percent 2 years ago. COBALT - The Societe Miniere de Tenke Fungurume (SMTF) copper-cobalt project in Zaire reportedly was suspended in January for an indefenite length of time. According to officials, the deferment resulted from a number of adverse factors, one of which was exceptional increases in capital costs. The project was scheduled for completion in early 1978, with an eventual production of 14.3 million pounds of cobalt per year. Reserves of cobalt were reported to be 505 million pounds. SMTF is a consortium and includes American, British, French, Japanese, and Zairian interests.

Jan 1, 1976

By M. G. Hester

The ore reserve modeling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high grade and low grade drillhole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1985

As students progress further into a degree, the decision of vocation selection, and even more importantly û securing employment in a particular industry sector, can become quite daunting. However, with a little initiative, students can overcome these issues by not only researching what employment opportunities exist, but by applying for summer vacation employment. Undergraduate vacation employment, especially with a world-leading hydrometallurgy research organisation such as the Parker Centre, can dramatically alter a studentÆs perspective of particular industries and possibly even alter their selection of vocation pursuits upon graduating. Students can also use vacation employment to enhance their networking capabilities, technical skills and knowledge by dealing with challenging new topics such as sulfur dioxide leaching, which is also discussed in this article.

Jan 1, 2005

By Walter W. Kaufman

The braking performance of underground, rubber-tired, coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are proposed.

Jan 1, 1977

By Arístides Sotomayor

El presente texto señala la importancia del oro a nivel financiero y minero ya que los inversionistas suelen utilizar este metal para obtener ganancias debido al mínimo riesgo existente en la pérdida de su valor comparado con otras divisas. Así, se estima que en el Perú, existen 480 unidades mineras de oro, de las cuales 28 concentran cerca del 90% de la producción nacional, como la Minera Yanacocha, Minera Barrick, Compañía de Minas Buenaventura, Consorcio Minero Horizonte, Aruntani y Aurífera Retamas. Entre las dos regiones que producen mayor cantidad de oro está: Cajamarca y La Libertad ( 38%) y la tercera región es Arequipa, seguida por Madre de Dios (9%).

May 1, 2016

By K. L. Paciorek

Organic materials utilized as cable Jacketing, cable insulation, standoffs, insulating boards and potting compositions were identified and d literature survey performed to obtain the required thermal oxidative and moist tracking data. Thirty representative compositions were procured and subjected to thermal and moist tracking evaluations. Tracking was found to invariably result in ignition or glow of the test specimen. Influence of parameters such as electrolyte strength and composition, temperature, conductor spacing, and electrode material were investigated. Volatile s produced by selected insulators on thermal oxidative and electrical stress were identified, quantitated, and their potential impairment action upon a current interrupter assessed.

Jan 1, 1980

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By McHenry Mosier

This paper describing mining practice at Morenci, Ariz., is one of a series of articles on mining method, and practice in the various mining districts in the United States. At present (1929) practically all the mineral production in the Morenci district is from the Humboldt mine of the Morenci Branch, Phelps Dodge Corporation. The mining method used is adapted to the type of ore body being exploited; it has been developed by adopting methods used elsewhere and making necessary changes to fit local conditions. Improvements in current practices are still being made.

Jan 1, 1929

By Shosei Serata

The application of conventional rock mechanics methods to complex ground is very difficult. Yet. In most underground mining, the ground is complex. Therefore. conventional methods are not only difficult to apply but are also generally ineffective in improving underground operations. Similarly, conventional rock mechanics instrumentation has not significantly contributed to improvement of mining practice. Rock mechanics instrumentation in underground mining operations is often considered to be" merely an expensive nuisance. A new system of mine instrumentation is changing this traditional view. The new instrumentation method, called the SPDR method, was originally devised by Dr. Shosei Serata to meet the specific requirement of establishing the Stress Control Method of mining upon a solid quantitative foundation. This instrumentation method has contributed substantially to the widespread success of Stress Control mining under widely varying ground conditions in different types of underground mines (1.2.3.4). The instrumentation method provides an effective means for optimizing Stress Control mining patterns, simultaneously achieving reduction in production costs and substantial improvements in safety (5). The principles and methods of the new instrumentation method are described below, with field examples.

Jan 1, 1986

By William D. Mayercheck

The U.S. Bureau of Mines is conducting research aimed at providing technology for a low-cost, high-recovery, environmentally acceptable mining system to recover the vast thin-seam coal reserves existing in the mountainous areas of the Appalachian region in the Eastern United States. As part of this research, the Bureau is evaluating new techniques to address these coal resources. This report summarizes the results of a worldwide technical search on thin-seam coal mining, the formulation of various methodologies for mining mountaintop thin seams, and the implementation and status of a physical model test program to validate and further develop the most promising concept-the "roof-fall-tolerant" mining system.

Jan 1, 1990

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner?s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutterhead, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head?s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner generally improved air quality at both sampling locations to varying degrees in some, but not all, mines when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By Sarkis G. Ampian

Published optical microscopic and X- ray diffraction characteristics of the following compounds are critically evaluated and compared with Bureau of Mines data : Tricalcium aluminate , calcium monoa luminate , dodecacalcium heptaluminate , dicalcium silicate , tricalcium silicate , and sodium aluminate . A recommended set of definitive optical and X- ray diffraction characteristics is presented . These values are used to identify products of the lime soda sinter process for production of alumina . Polymorphism of gamma- , beta- , and alpha prime - dicalcium silicate is reexamined , and new data are presented on polymorphism of tricalcium silicate and sodium aluminate by high- temperature X- ray diffractometry . Polymorphism is not observed for tricalcium aluminate , calcium monoaluminate , and dodecacalcium heptaluminate . Bureau of Mines data indicating a stoichiometry of 12Ca0.7A10 for the phase 5Ca0.3A1 0₂ are discussed . A critical review of the literature concerning calcium dia luminate and sodium undecaluminate ( 8 -A10 ) is also included .

Jan 1, 1964

By V. J. Southey

HOLLINGER mining operations have required development by 24 vertical shafts having a total length of 28,160 feet. Seventeen of these are sunk from surface and seven are interior shafts. Four surface shafts and three interior shafts are now active and, excepting the recently completed new main ore-hoisting shaft, the remainder are either abandoned, or are used for passes or for ventilation. The new shaft bottoms 60 feet below the 3,050 level, but there is much work to be done before it is placed in service. The term 'shaft practice' is intended to include shaft construction and a general treatment o typical equipment. It is a large subject for an organization the size of Hollinger and this paper is intended only to present the salient features. The writer wishes to thank the management for permission to publish this information and to acknowledge the advice and criticism o A. G. Irving, chief engineer, and the willing co-operation of other members of the Hollinger staff.

Jan 1, 1939

By John E. Shively, Tracy K. Lundin, Francis Fong

The Superconducting Super Collider (SSC) features two 20 TeV counter rotating proton beams which will be housed in 87 km (54 miles) of tunnel. Four additional lower energy particle accelerators will be housed in 26 km (16 miles) of tunnel and underground structures. Physics experiments will be conducted in two underground detector halls approximately 67 m (220 feet) deep with footprints measuring about 30 m (100 feet) by 100 m (330 feet). Definition and design of underground facilities is advanced with construction of approximately one-third of the SSC program underway. This paper presents an overview and status of the SSC project.

Jan 1, 1993