Search Documents

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By E. J. Gleim

This report describes a trip to Europe in the interest of safety in coal mines. It reviews the Eighth International Conference of Directors of Safety in Mines Re-search, which met in Dortmund-Derne, Germany, July 5-10, 1954, to discuss results of studies made in different countries to improve health and safety conditions under-ground. It also summarizes information on subjects of special interest in the United States gained by the writer in visits to mining experiment stations in Belgium, France, and England. The efforts being made to protect life and property underground were discussed, and ideas and experiences were interchanged freely, not only during the conference but also during visits to the several countries. Helpful information was obtained on many topics of interest, but time did not permit as thorough a discussion on some of them as might be desired.

Jan 1, 1956

By Javier Pozo

La herramienta de gestión corporativa más adecuada en el ámbito de la gran minería es el sistema EAM (Sistema Corporativo de Gestión Mantenimiento de Activos, Enterprise Asset Management). Para que este sistema se realice de manera exitosa, se requiere del compromiso y el apoyo de la gerencia. Posterior a esta etapa de implementación, se desarrolla la de consolidación, donde es importante el apoyo personal externo a la empresa para ejecutar tareas de implantación. Finalmente en SPCC fue necesario un cambio organizacional para la implantanción de MIMS.

Sep 13, 2001

By Paul H. Johnson

Chemical mining may be defined as the in-place extraction of metal values from ores located within the confines of a mine (that is, broken or fractured ore, stope fill, caved material, or ores in permeable zones) or ores located in dumps, prepared ore heaps, or tailing ponds. The term solution mining has, in general, been used to mean the in-place dissolution of water-soluble mineral salts with leach solutions. Chemical mining is presently in its embryonic stage. Basic research needs to be done to understand the influence of physical and chemical factors in chemical mining, and applied research needs to be done on both a small and a large scale to develop practical techniques of field practice. The areas of research include the following: (1) Leaching chemistry, the influence of physical, chemical, and biological factors in in-place leaching (2) Hydrodynamics of chemical mining systems (3) The development of new, as well as old, leaching agents for use under chemical mining leach conditions (4) The development of new means of contacting fine and coarse materials (with solutions) under static leach conditions (5) The development of new processes for generating and regenerating chemical mining leach solutions (6) The development of metal recovery processes

Jan 1, 1969

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company's management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007

By Dayu Long, Changhong Li, Yu Wang, Juzhou Li, Yongyue Hu

To address the problem of seepage failure that affects the stability of the fine-grained tailings dam, two kinds of prevention and treatment measures were proposed involving composite flocculants and composite curing agents. The orthogonal test was conducted to determine the optimal ratio flocculant (ORF) and the optimal ratio curing agent (ORCG). Then, numerical models were established to evaluate the effects of the prevention and treatment measures on the seepage and stability of the tailings dam. The results show that the mechanical properties and microstructure of the tailings are significantly improved by adding the ORF and ORCG. Furthermore, numerical studies suggest that the addition of the ORF and the ORCG to the tailings improves the factor of safety of the tailings dam, but the addition of the ORCG also increases the height of the phreatic line. It is also speculated that the addition of the ORF can prevent the formation of through failure zone in the tailings dam. Therefore, the optimal measure to prevent seepage failure in the tailings dam is adding an appropriate amount of the ORF, as it reduces the height of the dam’s phreatic line and lowers the risk of seepage failure. The typical area susceptible to seepage failure can be treated by adding the ORCG. However, it is important to ensure adequate drainage of the area and to maintain the phreatic line at a reasonable buried depth.

Mar 4, 2024

By F. Lindroos

A cornerstone in the LKAB Green Pellet concept is to produce pellets with a small footprint in terms of energy con-sumption, CO2 emission and emission of other elements harmful to the environment, like dust, sulphur dioxides, nitrogen oxides, chloride and fluorine. The concept also encompasses our determination to make pellet products that contribute to low environmental impact and low energy consumption in our customer?s processes. The presentation will focus on the pelletizing process. It will describe both how we have attempted to decrease the generation of unwanted components in the process gas, and how we have tested or evaluated equipment for external gas cleaning. We will discuss and give examples from recent and on-going efforts and outline some of the future challenges we see, to meet our own environmental standards and also the tough demands imposed by EU and national legislation, while striving to boost production.

May 1, 2011

By A. T. Miesch, L. B. Riley

Distribution of minor elements in sandstone-type uranium deposits of the Colorado Plateau is being studied by the USGS on behalf of the A EC. A primary objective has been to provide basic data which could be useful in geo-chemical exploration for new deposits. The basic statistical measures — similar to those used in sedimentary petrology—are described. The underlying principle is that the frequency distributions fit or approach the log-normal form. Since 1952 the U. S. Geological Survey on behalf of the U. S. Atomic Energy Commission has conducted a study of the distribution of minor elements in sands tone-type uranium deposits of the Colorado Plateau. A primary objective in this study has been to provide basic data which could be useful in geo-chemical exploration for new deposits. Among the basic data considered important are estimates of the abundance and habit of each element in the ore and in the host rocks. It has been found that a few basic statistical techniques, and variations of these techniques, are useful in this type of study. Some of the basic techniques have been used to advantage by researchers in geochemistry and in other fields of geology, especially sedimentary petrology; others have been used to only a limited extent. Among the latter is the linear correlation coefficient, which has proved useful in assessing the element associations in a particular rock type without analysing individual mineral separates. In computing the basic statistical measures a scale has been used which is, in some ways, similar to the phi ($) scale used by sedimentary petrol-ogists in grain-size studies.' FREQUENCY DISTRIBUTIONS It has been recognized for some time that the results of analyses for a given minor element in a suite of samples of rocks or ores yield frequency distribution curves which are approximately normal when the curves are plotted on logarithmic or geometric scales. In other words, the analytical results give an approximate lognormal frequency distribution. A classical example is given by D. G. Krige2 in the study of the distribution of gold values from a mine on the Witwatersrand. Another example is shown in Fig. 1, the distribution of barium concentrations in samples of uranium ore from the Chinle formation. The geochemical data are analogous to grain-size data gathered by the sedimentary petrologist. Both types of data, after simple logarithmic transformations, may be treated by conventional statistical methods based on the normal distribution. This is not to say that other types of transformations may not serve equally well or better for particular element distributions.3 Spectrographers and other analysts are quite aware of the dependence of their precision on the concentration of the element present.4 For example, in the part per million range the variation may

Jan 1, 1961

The use of scrapers in mining and earthmoving operations is not new, in fact they are one of the earliest methods of bulk earthmoving. A single machine which can load, haul, and dump material with a minimum of ancilliary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancilliary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By Carl Henrich

Jan 1, 1893

By James McGough, Lawrence Mirabelli, Ran Tamir

The paper will demonstrate how automated fragmentation photo analysis is being used at the Lafarge North America, Ravena NY quarry as part of an ongoing drill, blast and primary crushing continuous improvement process. Using on-line fragmentation photo analysis systems at both the primary crusher feed point and crusher discharge belt, data is collected to: benchmark the drill/blast process; monitor the work being done by the primary crusher; measure gradation changes in the crusher feed resulting from changes in drill/blast and measure the subsequent changes in further size reduction done by the primary crusher.

Jan 1, 2012

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009

Phosphorus Phase Analysis of Medium-Low-Grade Rare-Earths-Bearing Phosphate Ores

Sep 13, 2010

By Allan Breitenbach

Leaching has been used since the 1600s on unlined ore dumps and since the late 1970s on lined leach pads for the recovery of metals from mined ore, the latter typically called ?heap? leaching and the former ?dump? leaching. Modern day run-of-mine (ROM) or crushed ore heaps are stacked in controlled lifts on lined leach pads and irrigated with a solvent solution (dilute alkaline cyanide for precious meals, dilute sulfuric acid for base metals and uranium). Conventional lined leach pads store process solutions and any storm water, snow melt and cumulative wet season surplus water by gravity flow to external ponds. Impounding valley leach pads (also known as valley fill heaps) differ from conventional leach pads by storing various combinations of process liquid solution and surplus water within internal ponds by using the interstitial pore volume of the ore. While impounding liquids within the heap is simple in concept, impounding leach pads are more complicated for construction and containment compared to conventional leach pads with external ponds.

Jan 1, 2012

By Trevor Ellis

The following is extracted from a report by the author to the International Valuation Standards Committee (IVSC), with minor modifications for the purpose of publication. The author represented the IVSC at the annual session of the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology. This is a body organized by the United Nations Economic Commission for Europe (UNECE). This second session, held in Geneva, Switzerland, achieved an important agreement for advancement toward uniform global standards for the classification of minerals and petroleum reserves and resources. Attendees discussed the possibility of enhancing the United Nations Framework Classification for Energy and Mineral Resources (UNFC) for implementation globally as the classification standard for use in financial reports under the International Financial Reporting Standards (IFRS). Presently, there are between 100 and 200 mineral and petroleum resource classification (or definition) systems throughout the world — a similar number to what there are countries.

Jan 1, 2006

By C. J. Hall

I would like to congratulate Professor Gershon on an idea that is obviously valuable and is certainly new to me. It has, however, to be further developed, in that one can get fallacious results by limiting oneself to positional weights. In the example problem, the positional weight of one block was 8.6 (the 8.0 value in the paper was incorrect) for 36 units in the cone, for a mean block value of 0.239. The positional weight of the second block was 4.4 for 15 units, for a mean block value of 0.293. Surely one would expect the second block to be rated higher. Additionally, the time value of money adjustment cannot be determined by depth, because the time that a block is mined is determined by the mining sequence, not depth. Figure 1 shows a slightly altered version of Professor Gershon's pit. The overall value of the pit is the same, as are the total values under each of his blocks. The values in the right-hand cone have been reversed top to bottom, and the values in the rest of the pit adjusted to keep the central cone total unchanged. All values have been multiplied by 10. Figure 2 shows the sequence of mining, at three blocks per year, for Professor Gershon's pit, and Fig. 3, the sequence for a pit under the other block. Table 1 shows the value and discounted value (15%) of Professor Gershon's pit, and Table 2 shows similar values for the second pit. It is apparent that the second pit schedule is more valuable than the first.

Jan 1, 1988

By Stephen P. Signer

The U.S. Bureau of Mines is developing an intelligent system for roof' control that uses both an expert system and neural networks to improve the capability of mining engineers to evaluate roof support effectiveness for ground control in coal mines. The expert system com- pares roof support capacities with the support requirements estimated to be necessary to maintain entry stability. It does this by evaluating the results of tests on various types of roof support and establishing the maximum allowable load according to anchorage capacity and yield strength of the support. After the user enters geological information (rock properties, geometry of the opening, in situ stresses, bolt pattern parameters, etc. ), the expert system compares the predicted required loading to the roof support capacity and gives the operator advice on the adequacy of the design and how improvements could be made. A good source of the real-time data necessary to allow the expert system to make decisions will come from a roof bolting machine being developed by the Bureau of Mines. Researchers have collected data from a Western coal mine on drill bit position, penetration rate thrust, torque, and rotation rate. Using this information, two neural net- works were developed to identify different types of strata and features in a mine roof such as rock type, rock compressive strength and joint characteristics. The result is a system that can assist a mining engineer with design information that can be constantly updated as mining progresses.

Jan 1, 1992