Search Documents

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

By K. Stout, L. Friel

Some rock mechanics theorists believe that if a hydraulically placed backfill can be introduced in a stoped out area, which will minimize wall closure by taking high stresses across the fill with minimum compaction, then heavy ground and rock burst phenomena will be minimized. The paper will discuss a large scale laboratory project when fill strength was increased over four times by the head vibrated method and up to well over 20 times by the double placed, cemented, vibrated head method when compared to conventionally placed fills. The only preconditioning of the 60% solids by weight slurry was the addition of cement in some tests.

Jan 1, 1983

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

Mining of copper ore is still the most important business in Chile. In order to mine ore with a copper content of less than one percent at Minera Los Pelambres in an economical way, opencast mining is mandatory. Due to the prevalence of avalanches at the mine, the concentrator was located in a stable area, some distance from the mine. As a consequence, the material has to be transported between mine and concentrator by conveyor. A downhill conveyor system has been implemented for more than ten years as the most suitable and most economical ore transport alternative. Due to the length (12.6 km) and inclination (1300 m drop) of the conveyor system, the stresses in the steel cord belt are the dominant design criterion, resulting in a belt quality of ST 7800. Additional dynamic belt stresses during transient operating conditions are avoided by the installation of high capacity adjustable frequency drives. The rating of a single drive unit is 2500 kW. During ten years of operation, several capacity increases have been implemented, from an initial 5800 t/h up to the current capacity of 9900 t/h. This presentation describes the engineering challenges of the implementation of the world's strongest belt conveyor system. Capacity increase measures like the development of new control and breaking strategy, proved by dynamic simulation of belt forces and belt speed scenarios are explained. During this long-term partnership of RWE Power International, the former Rheinbraun Engineering, with Minera Los Pelambres, RWE has been engaged continuously for development work, safety checks, expert opinions and maintenance audits, and giving new impulse to conveyor technology.

May 1, 2010

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By D. P. Cook, Jr. Jones, J. W. Evans

"It is well understood that the flow of liquid metal in the mold region of the caster can have a notable effect on the overall solidification behavior in aluminum casting. Previously our group has characterized the flow in this region in a water model, using particle imaging velocimetry. The flow is significantly effected by the specifics of the metal delivery system, i.e. size, geometry, used during the cast. Recently, a time-averaged 3D numerical model of the nozzle, combo bag and sump region has been developed and its validity has been tested against experimental data. Cases were run for different sized combo bags as well as bags that have been blocked. The results show satisfactory agreement between the physical and mathematical models.IntroductionFluid flow in the head of an electromagnetic (EM) and direct chill (DC) ingots has been shown to effect many important operational parameters in casting such as superheat removal, macrosegregation, and hot cracking. In most cases, the momentum from the nozzle is diverted through a delivery system, termed a bag, before entering the mold region. The specific geometries of the bags vary widely from operator to operator suggesting that there is still some question as to the optimum design. Several studies [1-4] have been carried out to understand the influence of the bag design on the solidification behavior in aluminum casters. However, few studies have included numerical prediction with experimental verification. Unfortunately, many simulations performed today still do not accurately account for flow in such devices.Recently, a significant amount of research into the flow resulting from the metal delivery systems has been performed [5-8]. The thrust of this research has been characterizing the flow patterns by a measurement technique called particle imaging velocimetry. The data suggest that the method of delivering the liquid metal into the mold region has a significant effect on the nature of the flow. With a detailed set of quantitative data from a water model, a numerical model can be built and tested to ensure a proper description of the flow field. The computational model used in these simulations is designed to represent a laboratory scale model of a caster in which ""combo"" bags were simulated. Such bags are mostly of a densely woven glass fiber material with low permeability to aluminum. ""Windows"", of a more open weave, permit aluminum to flow from the bag, see Fig. I. Two different sized combo bags were modeled, each subject to two different outflow window configurations. Furthermore, experimental measurements [9] were used to validate the model results."

Jan 1, 1999

By K. I. Afewu

A modified approach to the implementation of Gy?s sampling theory is discussed and used to design a procedure for sampling crushed gold ore feed to metallurgical process plants. The approach involves calibration of certain ore-specific parameters. These parameters were calibrated for two different crushed gold ores en route to grinding mills in process plants. The model predictions were compared with the predictions from Gy?s original model. Far smaller masses of samples are required by the modified model than by Gy?s model at the same relative variance. The representativeness of the sampling procedure if normally distributed errors are assumed was also calculated. These procedures and evaluations lead to significant savings on cost of handling and preparation of the samples and to a quantifiable degree of confidence in the analytical results for the process plant.

Jan 1, 1998

By AIME AIME

INSTITUTE members attending the Annual Meeting in New York who want to see one of the mining engineers' newest aids, photoelastic stress analysis, are due for an interesting afternoon on Thursday, Feb. 15, when open house: will be held at the Columbia University mining laboratory. Information as to the direction and distribution off stresses in mine structures, which has been developed by Professor Bucky, associate professor at the Columbia School of Mines, and David Sinclair, research assistant, is useful in the design of pillars and in the placing of openings relative to working places such as gangways and haulage levels.: This work has been sponsored during the last ten years by the Engineering Foundation.. It is fully reported in T. P. No. 1140.

Jan 1, 1940

By V. T. McLemore

Petrographic analysis of rocks is traditionally performed with optical microscopy using thin sections and point counting. However, this does not provide accurate mineral proportions for sedimentary, volcanic, and soil-like material, because rock fragments, groundmass, and matrix are not identified as specific minerals. In addition, groundmass phases in volcanic rocks can be too fine to identify individually, and making thin sections of intact soil-like material is difficult because much of the material is not well cemented. ModAn is a normative calculation that estimates modes ??by applying Gaussian elimination and multiple linear regression techniques to simultaneous mass balance equations? (Paktunc, 2001) and allows location-specific mineral compositions to be used. One of the features of ModAn that makes it appropriate for this study is that it can model one of several sulfide minerals. Mineral compositions for Questa minerals were determined from electron microprobe analysis and entered into ModAn. Then by combining and normalizing results, bulk quantitative mineralogy can be determined using ModAn, petrographic observations, electron microprobe analysis, clay mineral analysis, and the whole-rock chemistry of the sample.

Jan 1, 2009

By R. Rosenblum, J. Y. Kim, D. Shink, K. G. Stowe

"A small scale continuous flotation cell was designed and constructed at the Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine.This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results. INTRODUCTIONStudy of the behaviour of an ore during concentration by flotation process starts, in general, with a series of tests in laboratory cells. Given the discontinuous nature of these tests, the information obtained by such a study is somewhat limited. It has long been recognized that laboratory test results are not always reproducible in pilot plant tests and subsequently, the pilot plant results do not always predict plant performance. The differences are often blamed on batch vs continuous operations, grinding media, size distribution, aging (oxidation), water quality, equipment, operator's skills, etc."

Jan 1, 1992

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Steve Kral

The upswing in prices for base and precious metals, industrial minerals and coal has allowed the global mining industry to ramp up production at existing mines and begin construction of proposed projects. In addition to satisfying shareholders, the industry is also providing good paying jobs and creating needed infra-structure in places that previously did not have either. However, the industry has learned that the prospect of jobs and infrastructure is not necessarily a guarantee that communities will allow mines to be built. The industry must maintain even higher environmental and reclamation standards. And mining companies must help communities plan for life after a mine is closed and the company moves out.

Jan 1, 2005

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

By Joseph Moses Botbol

In passing the judgments essential to his trade, the geologist may be assisted by two new methods. These will enable him to (1) arrange the minerals of a selected group of base metal mining districts in the order of their typicalities and (2) compute the degree of mineralogic association between the model so derived and a district external to the model. It must be remembered, of course, that the methods discussed in this article are no more powerful than the structure of the model used and the data available. The geologist who employs these techniques must still exercise his expertise

Jan 1, 1970

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By Eung Ha Cho, Wendi Li

Wet desulfurization of Pittsburgh No. 8 coal and Illinois No. 6 coal were conducted with sodium hypochlorite in the laboratory. Pittsburgh No. 8 coal was leached by hypochlorite at high pHs in one step only. The hypochlorite concentration varied from 0.2 to 0.6 molar; sodium hydroxide concentration, from 0.2 to 0.8 molar; and temperature was at the levels of 80 and 90°C. The desulfurization of Illinois No. 6 coal was conducted in three consecutive steps of pretreatment in concentrated ammonia at room temperature, leaching with hypochlorite at room temperature and hydrolysis in sodium hydroxide solution at 90°C. In the leaching step, hypochlorite concentration varied from 0.2 to 0.8 molar. The desulfurization method of Pittsburgh No. 8 coal was found to reduce mainly pyritic sulfur. More than 70% of pyritic sulfur removal was achieved at the optimum conditions of 0.4 molar hypochlorite, 0.4 molar sodium hydroxide and 90°C. The desulfurization method for Illinois No. 6 coal was capable of reducing significant amounts of organic sulfur. The removal of organic sulfur achieved a 37.8% reduction at the optimum operation of leaching at 0.4 molar hypochlorite and room temperature followed by hydrolysis at 0.3 molar sodium hydroxide and 90°C. The chlorine content in the coal produced by the chlorination during leaching was kept below the threshold value of 0.3% at the optimum conditions of the desulfurization method for each coal.

Jan 1, 2005

By Dale S. Preece, Stephen H. Chung

Electronic detonators and the attendant precise detonation timing that they facilitate are having a measurable effect on rock blasting in terms of improved fragmentation and vibration control. These improvements are increasingly well documented which is driving the expanding use of electronic detonators. In spite of the growing body of positive evidence concerning the benefits of precise delay timing, very little work has been done to document the impact of electronic detonators on the movement of rock. In this study 3-D computer programs, used to predict blasting induced rock heave, including the effects of detonation timing, are used to simulate the effect of precise timing on rock movement. Implementation includes quick, precise timing between blastholes going down a row and then much longer delays between rows of blastholes. For example an effective blast design might call for precise 3 ms delays between blastholes along a row and then 60 or 72 ms between rows. Several options are studied in this paper using computer simulations to draw some conclusions about the underlying physics affecting the process and how precise timing might have a positive impact on blasting induced rock motion.

Jan 1, 2005

By J. S. Harington

Our purpose is to record and to explain the widely changing numbers of the huge total of black workers on the gold mines of South Africa over the century from 1896 to 1996. These men were recruited from up to twenty territories, and their contributions are examined. The major areas providing labour over this long period have been Lesotho, the former Transkei within South Africa and Mozambique. From 1989 to 1996, for instance, these three areas accounted for over sixty per cent of the total labour force (tlf). Our principal Figure 1 shows the tlf fluctuating through time to reach a peak of 480 000 in 1988. Irregular falls are also documented with the most serious in 1995 to 180 000. Based on this graph we consider the political, economic, sociological and historical reasons behind these changing employment opportunities. These have included external world-scale events such as war or depression, as well as internal changes of national economy and policy. We show the importance for numbers employed of the discovery of gold in the Orange Free State in 1946, the influence generally of the ?Winds of Change? and the firm maintenance by the State of law and order. Varying gold production costs and profitability against high tax rates, allied with increasing wages and a lack of development capital, have led in the last decade to employment falling by fifty per cent, despite an actually higher value of gold output. Finally, this analysis considers the role of the migrant labour system as it affects, and is affected by, conditions in the gold mining industry, with special reference to its less than humane consequences in the numerically dominant territories of Lesotho and Transkei.

Jan 1, 2004

By C. A. Rawlins

In an underground mine the ingress of heat can generally be attributed to two sources (Rock exposure and artificial mechanisms). The heat load relating rock exposure is subdivided into stoping [~40%] and haulages [~20%]. Rock is exposed to the ambient air and as a mine increases in depth the VRT (Virgin Rock Temperature) increases which leads to more heat ingress underground. To counter the heat ingress, especially in low-seam stoping areas of a deep level mine, air is, a) cooled artificially, b) the amount of rock exposed is reduced in the back areas of a stope by backfill applications, and c) ventilation air is used more efficiently. The heat reduction within a stope due to placed backfill could amount to ~50% for operations mining at a mean rock breaking depth of about 4500 mbc (metres below collar). Unfortunately, due to backfill transport methods, the physical fluid properties and application methods adopted, additional heat is induced into the air. The heat ingress due to backfill application could amount to as much as 25% of the overall in-stope heat load. This heat influx, seen as a negative aspect of backfill operations, is nevertheless overshadowed by the overall in-mine heat load reduction capability of about 20% attainable. The in-stope benefit [~50%] attainable from backfill operations could be increased with the incorporation of a heat exchange (cooling) methodology to offset the additional heat ingress into the surrounding air of a deep underground mine.

Jan 1, 2003