Search Documents

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Wern-ping Chen

Technical and non-technical challenges exist in each mega infrastructure project. It?s no exception to the first US underground PPP Port of Miami Tunnel (POMT) project in Miami, FL. The POMT will connect two man-made islands, the Dodge and the Watson Islands, under the Biscayne Bay within highly porous limestone formation. Permeability as high as 0.1 cm/sec has been identified. Its 41-ft outside diameter, if constructed, is the largest precast segment lining in the US. Besides its geological and hydro geological challenges and risks, local community influence and impacts have controlled the fate of this project. This paper describes its tender design enhancements and the evolving of its slow advancement in resolving local community issues.

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

The coal-based power generation industry faces increased pressure from all sectors to improve its environmental performance. This is due to increased awareness of and concerns regarding greenhouse-and acid-gas emissions, toxic metal releases (to both air and water) and water availability. A methodology to assess this industry?s environmental performance is needed. Such a methodology should assess all environmental impacts accurately, recognizing the irspatial and temporal dependence, and taking into account the social acceptability of technologies employed. Here, we develop a methodology to determine the environ-mental impact associated with solid wastes generated by this industry, and apply this to the specific case of ash management. More specifically, the case study compares the environmental footprint of an ash deposit for a number of operational water management scenarios. The methodology considers leachate generation processes from ash impoundments to obtain a time-dependent concentration profile of mobile constituents at the interface between the ash impoundment and the surrounding environment. This leachate prediction modelling is subsequently linked to plume dispersion modelling tools to determine the fate and transport of leached components, predominantly salts, into groundwater. Together, these provide a measure of the extent to which a land mass is affected by leachate migration from the deposit. To determine the exact boundary between regions of acceptable and unacceptable risk to the environment, we use Ecological Risk Assessment concepts. In this way it is possible to obtain a time dependent affected land footprint which could be used as an indicator of the environmental impact of solid waste management practices. This information can be included in a set of environmental criteria which form the basis of an overall environ-mental impact assessment, using tools such as Life Cycle Assessment (LCA). The value of LCA is that its structure is consistent with accepted models of environmental decision making, where different approaches to valuation in impact assessment assist in prioritizing impacts on the basis of their perceived significance. The proposed ?affected land footprint? metric represents a significant improvement over current LCA impact indicators for solid waste management practices. Keywords: Environmental Impact Assessment, Environmental Risk Assessment; Life Cycle Assessment; coal ash; leachability; salinity

Jan 1, 2002

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

By M. J. Allan

"The paper describes the author's experiences in the startup of autogenous and semiautogenous grinding circuits gained over the last twenty years on both large and small grinding circuits. Typical phases in commissioning from construction to startup with ore are covered. The paper also describes experiences with material handling systems, slurry pumping, vibrating screens, trommel screens and pebbles crushing systems. INTRODUCTIONThe commissioning of any new mineral processing plant is an important and exciting milestone in any project. It is at this point in time that the efforts of developers, design engineers, equipment suppliers and operators culminate in a finished product. The successful completion of any project requires that the plant achieve design throughput as quickly as possible. The success of any startup can generally be anticipated by the amount of careful planning which takes place before equipment is operated. The first part of this paper describes the steps in going from construction through to introduction of ore. The organization and planning of startup activities is also covered.The second part of this paper describes some typical problem areas and past experiences in the startup of semi-autogenous grinding circuits. Semi-autogenous grinding circuits present some special challenges in the startup phase. The description of some of these problems and experiences will hopefully provide other operators with suggestions on how to avoid (or at least prepare for) these problems."

Jan 1, 1992

Jul 20, 1957

By W. C. Meyer

The concept of using powdered coal-in-oil-mixtures (COM) as a composite fuel to conserve oil resources and relieve import supply problems is being vigorously promoted by the Department of Energy via the sponsoring of various demonstration units (1). The idea of COM as a useful alternative fuel has been explored on and off for over 100 years (2). The approach must be capable of grinding, mixing, storing, and combusting COM with presumably only minor equipment changes on oil-fired boilers. DOE estimates that 56 000 m3 of oil (350 000 barrels) could be spared daily if a 50-50 COM was used to generate electricity. Of course, the ability of COM suppliers to prepare and deliver a stable suspension of COM at reasonable economic costs must be achieved if the concept is to be successful. This report reviews the various methods used to attain stable coal-oil mixtures. Various physical-chemical principles associated with each method of stabilization are also discussed.

Jan 1, 1981

By Ian Townsend

A prerequisite for good filter performance is that the total filter installation has been well designed. In this sense, the filtration testwork will provide scale-up data, and an insight into the relationship between operating parameters that may then be optimised, and used in the development of a control strategy. A good understanding of the filter’s operating principles will ensure correct selection and sizing of ancillaries, allowing in particular for the difference between instantaneous and average flow rates.

Sep 13, 2001

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

The geological features of the destructive plate margins of the southwest Pacific favour the formation of porphyry type deposits. The major controlling factor favouring the formation of gold-rich deposits of this type is a dense crust. This results in shallow intrusion of large magma bodies beneath andesite stratovolcanoes. Where the intrusives have near vertical sides, the comparatively low temperature of transfer of volatiles from the solidifying melt favours the partitioning of gold into bubbles of volatiles. They reduce the viscosity and density of the melt, resulting in the upward movement of a mineralised melt. With the drop of pressure with upward movement the bubbles separate into a two phase mixture, triggering freezing of the mineralised melt and the formation of a gold mineralised stockwork.

Jan 1, 1995

By A. Feather

The Minataur? Process (Mintek Alternative Technology for Au Refining) is a novel route for the production of high-purity gold using solvent extraction. Following the successful demonstration of the process on a pilot-plant scale, a full-scale 24 t/a production plant has been commissioned at Harmony Gold Mine in Virginia, Free State. The commercial implementation of this process represents not only a significant advance in gold-refining technology, but may be instrumental in initiating important changes in the legislation regulating the marketing of gold in South Africa. Gold of either 99.99% or 99.999% purity can be produced from intermediate process products having a wide range of gold contents. The process comprises oxidative leaching of the solid feed, followed by selective solvent extraction of the gold from the leach liquor to reject impurities, and precipitation of high-purity gold powder. This paper outlines the process, presents selected results of two pilot-plant trials in which 5 kg/d of high-purity gold was produced from silver-refining anode slime and gold-electrowinning cathode sludge, and provides some details of the cost benefits.

Jan 1, 1997

By John McDonald

THIS report is a continuation of an earlier one with a similar title,1 to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as re-ported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be com-pared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a con-siderable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated.

Jan 1, 1940

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By R. Heersink, C. H. Wells

Innovations in communications and real-time information systems are providing industry opportunities to improve profitability. Real-time operating data is collected from equipment across a site or even several sites into a central server for secure PC and PDA-based Internet access. This paper includes discussion of how operating staff can use wireless devices to see equipment and processing data from anywhere throughout the mines and concentrators, and how management can view results from multiple mines, all in real time. Additional opportunities enabled through the remote access by equipment vendors or mining consultants is also presented, as well as an overview of typical benefits and current installations.

Jan 1, 2002

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2000

This Bureau of Mines publication presents five papers given at a Technology Transfer Seminar on Metal Mine Fire Protection Research. Several seminars are held each year to bring the latest results of Bureau conducted and sponsored research to the attention of the mining industry as quickly as possible.

Jan 1, 1977

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By J B. Taylor

Geographic Information Systems (GIS) are being increasingly used by the mineral exploration industry in the search for new ore deposits. A mineral exploration GIS links geological and geophysical data by virtue of their geographic location in a digital map setting. Geological and geophysical data are categorised into a number of themes or layers within a mineral exploration GIS. These layers may include polygonal information such as rock type and tenements, line information such as faults and fold axes, point information such as mines and mineral occurences, and images such as gridded geochemistry and aeromagnetics. A mineral exploration GIS is a powerful tool to help the explorationist comprehend the spatial associations and interrelationships of his/her data. These spatial associations can be integrated with a mineral genesis model, to create a mineral prospectivity map to more effectively target exploration. Arguably a competent geologist who has a good understanding of the genesis of the local ore deposit types and knows their local geology backwards could intuitively derive a mineral prospectivity map. However, in an era of rapid data accumulation from many different disciplines, the ability to assimilate and understand is a huge task for any individual. A mineral exploration GIS enables the explorationist to spend more time analysing data and testing ideas, rather than finding and manipulating data into compatible formats.

Jan 1, 1994