Search Documents

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By I. A. Minaev

The conditions of a stability of metallurgical films on a surface of solid on the basis of classical regularities of a thermodynamics are considered. For specific conditions of metallurgical processes the basic equations relevant to non-metallic inclusions (product of steel killing) migration and transfer through the interface boundary of metal-slag are obtained. The basic criteria equations of conditions of stability of metallurgical dispersed systems are developed in view of films formation. The probable thermodynamics reason of wetting due to formation of stable films are discussed. The experimental measurement of thin and thick films elastic resistance for metallurgical systems are carried out and the results are discussed. The presence of a wetting thick film increases stability of dispersed systems (facilitates an inverse implication of non-metallic inclusion in a melt) due to a barrier effect of wetting films. The quantitative evaluations of non-metal inclusion stability for steel in contact with any metallurgical slag are carried out. The results are in accordance with technological experience. Keywords: Inclusion removal, Film thermodynamic, Slag-metal dispers system

Jan 1, 2004

By R. I. Garrod, R. A. Coyle

The shapes and positions of X-ray reflections from specimens of copper, steel, and aluminum alloy haue been examined in the elastic and plastic ranges both while the specimen was under stress and in the unloaded condition. For the aluminum alloy the shape was unaltered by the application of stress either within the elastic limit or in the plastic range provided that no additional plastic strain was induced. In copper the broadening accompanying plastic deformation was very slightly reduced when the specimen was unloaded. A similay but more marked elastic component of broadening was also found for steel, but in this case below the yield stress. Line profiles corrected for instrumental and particle-size broadening indicate very large internal stresses in local regions of the plastically deformed metals. The results are discussed in terms of a recent suggestion that the heterogeneous dislocation distribution between the cells and their boundary walls plays a major role in the peak shifts and broadening of the X-ray reflections. STUDIES of the X-ray line profiles from strained polycrystalline aggregates concentrate usually on one or the other of two main parameters: a) the displacement of the peak of the intensity contour from its position for a strain-free aggregate, or b) the shape of the profile. From peak shifts data can be obtained either on the relation in both the elastic and plastic ranges between applied external stress and average lattice strains in a given (hkl) direction, or, alternatively, on the residual lattice strains which are present after a plastically deformed specimen is unloaded.' On the other hand, the shapes of the broadened profiles from cold-worked metals can be analyzed to separate the broadening produced by small particle size and by heterogeneous lattice strains.' In this paper the terms "size broadening" and "strain broadening'' are used in the general sense adopted by warren.' In the past, apart from two early qualitative observation, it has been customary to examine only the movements of the peaks of the profiles while the specimen is actually under load, since the line broadening induced by plastic strain remains after removal of the external stress. Consideration of the implications of existing data of this type suggests, however, that fruitful additional information on a number of fundamental aspects might be gained by careful examination of whether the X-ray line profile is in fact different in the loaded and unloaded states of the specimen. By taking advantage of the sensitivity and convenience of modern diffractometer techniques it is possible to explore with relative ease the magnitude and importance of any elastic effects which may be superimposed upon the well-known permanent changes in profile. The main aim of the work to be described was thus to investigate this point for typical metals and alloys. For this purpose annealed specimens were extended first elastically and then plastically and the positions and shapes of X-ray reflections were recorded. Initially it was anticipated that prime interest would center on observations within the plastic range; it has been found, however, that small changes in profile sometimes occur both before and after the nominal elastic limit of the material is reached. It is shown that the results obtained have important implications in relation to the structural changes and processes associated with deformation. I) EXPERIMENTAL To enable the diffraction lines to be recorded while the specimen was under uniaxial-tensile stress, a small hydraulic testing machine was designed and constructed for direct attachment to the goniometer of a Philips diffractometer. The specimens, which were machined from 1/2-in.-diam rod and had a central rectangular section 3/8 by 1/16 in. over a gage length of 1 in., were held in the machine by split collets mounted in grooves in the cylindrical ends of each specimen. No special precautions were taken to ensure precise axiality of loading. Constant oil pressure was maintained by a lever and weights system and transmitted to the loading rig by flexible pipe. The actual load on the specimen was measured by a load cell in the machine to an accuracy of * 1 pct. To enable smooth X-ray profiles to be obtained the specimen and machine were oscillated continuously during recording through *7-1/2 deg about the normal half-angle position of the goniometer. The three materials chosen for the investigations were high-purity copper as representative of a ductile fcc metal, a low-carbon steel for a bcc metal, and an aluminum alloy as a material in which the proof stress/ultimate strength ratio is high. Details are as follows. a) Copper. 99.999 pct purity. After machining the specimen surface was polished mechanically and

Jan 1, 1964

By J. P. W. Bennie, A. de Jong, G. M. Denton

Mintek together with Middelburg Steel & Alloys, developed the DC arc furnace process for the production of ferroalloys with the expressed objective of smelting ore fines (<1mm) without the need for agglomeration. In the case of ferrochrome production, the DC arc furnace, being a semi-open bath operation, loses radiant energy directly from the bath to the furnace roof and sidewalls above the melt. This energy loss is reflected in a higher electrical energy usage per ton of alloy than for a submerged-arc operation smelting lumpy ores or sintered pellets. The difference increases still further when pre-heated sintered pellet feed is used in a submerged-arc operation. This shortcoming of the DC arc furnace can however be overcome by preheating the feed to the furnace in a fluidized bed or flash reactor fuelled by cold furnace off-gas. In addition to fluidization and preheating testwork, various preheating flowsheets with associated mass and energy balances have been developed and compared from a techno-economic viewpoint. The three major advantages identified were: a) fluidized beds can preheat ores and fluxes up to 950°C without sticking and defluidizing, b) the open bath DC arc furnace does not require expensive coke or char to maintain the burden porosity and, c) the capital cost associated with the milling, pelletising and sintering plant falls away since ore fines are used directly.

Jan 1, 2004

By A. V. Pavlov, A. V. Dubachev, K. L. Kossyrev

The purpose of the given research was to investigate the possibility of high-carbon ferrochromium refining to remove harmful impurities as a result of metal treatment by slag mixtures on the basis of the CaO-MgO-SiO2system. The final conclusions were drawn from experimental results. It was shown that the treatment of high-carbon ferrochromium by SiO2-MgO-CaO slag mixtures with additions of chromium sinter or iron-ore concentrate removes carbon, sulphur and phosphorus from the metal. A mechanism of phosphorus removal from a melt to a gas phase is proposed.

Jan 1, 2004

By M. Wright, A. H. Mwale

Opportunities to promote enhanced eco-efficiency (i.e. the simultaneous improvement in economic and environmental performance) for the minerals industry exist across the whole value chain. However, given the current operational models of major companies within the industry, and their focus on refining of primary ore bodies, it is important to understand where such opportunities might lie within minerals beneficiation, as it is here that major environmental pressures are felt. This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. In addition, this work provides a useful baseline against which to analyse the potential for dry processing. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered, supported by operational data from Zambian copper mines.

Jan 1, 2003

By Wayne I. van Drunick

"Energy balance modeling has recently been shown to be a competent tool in the estimation of SAG mill discharge rheology. Work performed by van Drunick and Moys (2001) validated the ability of an energybalance filter to estimate the slurry density from an operating SAG mill. The importance of rheological data is highlighted by several authors who show the effects on load behaviour and thus mill performance. Energy balance models were developed to account for the dynamic energies in the mill discharge sump. The models then made it possible to infer the mill discharge density. A sampling campaign was performed and the errors from the sump energy balance were within tolerable limits.Since the initial results were published, it has been decided to further develop the modeling techniques in order to focus on balancing the energies around the entire mill. The critical measurements for the energy balance will be the temperatures of all the streams entering and leaving the mill, including energy losses to the environment. Metso’s OCS© (Optimising Control System) currently controls the 3 SAG mills at Anglogold’s Mponeng Gold Plant (South Africa). The OCS has built-in Kalman filtering tools to effectively handle variances and noise in the models and the mill circuit data respectively. The new models are therefore constructed in the OCS platform, and will be run in parallel with Metso’s current modeling and filtering systems. The work is a collaborative effort between Anglogold, the University of the Witwatersrand and Metso. The benefits of energy modeling, compared to mass modeling, are that energy data are more accurately measurable than mass data. The inferred mill parameters can therefore be improved provided that a competent set of models is produced to process the (accurate) thermal measurements."

Jan 1, 2003

By Jochen Petersen, Harro von Blottnitz

"The landfill disposal of slags is common practice in the metallurgical industry. Chromium may be a minor constituent in many cases. It is present mostly in the form of chromites, which are considered environmentally benign and hence safe for disposal. Wastewaters from metal finishing operations are most commonly treated by reduction and precipitation of dissolved metals, including chromium, by lime addition, and subsequent landfill disposal of the resulting sludge. The metals contained in such sludges are mostly in the form of hydroxides, and as such considered environmentally stable.Thermodynamically, trivalent chromium, which is the predominant form in these waste materials, can be oxidised to the hexavalent form by atmospheric oxygen. Detailed research work on both slags and sludges has shown that a gradual emergence of hexavalent chromium can indeed be observed. The mechanism is governed by close physical contact between chromium oxide (or hydroxide) phases on the one side and calcium oxide (or hydroxide), which is present as flux in slags and residual lime in sludges, on the other. If oxygen can migrate to the points of contact, gradual formation of calcium chromate ensues.Hexavalent chromium is associated with high environmental toxicity, and hence undesirable in landfilled materials. Moisture migrating through landfill deposits can mobilise the highly soluble chromates and thus potentially transport them into natural waterways. Such gradual release from stainless steel and ferrochromium slag deposits has been demonstrated in a column experiment."

Jan 1, 2003

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Mineral froth flotation is one of the most widely used processes to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. The hydrophobic particles attach to the air bubbles and rise up to the froth phase on top of the slurry. The valuable mineral is collected when the froth overflows the cell wall. The separation performance of the process can be linked to the amount of solids and valuable material loaded on the bubble shells. In addition, it is well known that in most mineral systems, the presence of solids can enhance the stability of the froths. How the solids get to be distributed and what proportion is actually attached and stabilising the bubbles is not well known.This study aims to establish the relationship between operational variables, solids loading on bubbles and flotation performance. For this purpose, a series of industrial experiments to sample the solids in the bubble films under different operational conditions were carried out in two copper concentrators under steady state conditions. Samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. The amount of solids and liquid per unit area in the bubble lamellae can subsequently be estimated gravimetrically and by image analysis. The grade of the attached particles was also measured by adequate sampling. This gives an indication of the maximum grade that could be achieved from the process under the operating conditions."

Jan 1, 2003

By Sun Chuanyao, Jia Muxin

Generally, if the bond valence (BV) between metal ion and oxygen of the mineral is greater than 0.8, only surface species –Me-O-H or –Me-O exposures on the mineral interface, if the BV is between 0.2-0.8, the metal ion exposures on the interface, and if the BV is less than 0.2 the metal ion dissolves into water. The PZCs of oxide minerals and island silicate minerals are determined by the bond valence of the bond in the mineral crystals, the higher the bond valence the lower the PZC of the mineral. So the PZC sequence of Al2SiO5 minerals is kyanite> andalusite> sillimanite. The general rule for framework silicate minerals is as: The higher the Al content, the lower the PZC of the mineral, when the ratio of Al to Si in the tetrahedron skeleton is below 1:3. The higher the Al content, the higher the PZC of the mineral, when the ratio of Al to Si in the skeleton is between 1:3 and 1:1. The general rule for layer silicate minerals is summarized as: the three-layer silicate minerals have much lower PZCs than that of the two-layer silicate minerals. The threelayer silicate mineral with the octahedron layer occupied by lower charged cations has lower PZC than that of the three-layer silicate mineral with the octahedron layer occupied by higher charged cations. The twolayer silicate mineral with the octahedron layer occupied by lower charged cations has higher PZC than that of the two-layer silicate mineral with the octahedron layer occupied by higher charged cations. The layer silicate mineral with Al substitution in the tetrahedron layer has lower PZC than that of the layer silicate mineral without Al substitution in the tetrahedron layer. Such pyroxene minerals whose M1 is occupied by a trivalence cation and the M2 is occupied by a monovalence cation has lower PZCs than those both M1 and M2 are all occupied by bivalence cations. Such hornblende minerals whose M2 is occupied by a trivalence cation and the M4 is occupied by a monovalence cation has lower PZCs than those both M2 and M4 are all occupied by bivalence cations. There is no Si4+ or 4 coordinated Al3+ exposures on the surface of framework silicate minerals, the metal ions of three layer or chain silicate minerals are compact between tetrahedron layersor chains, they hinder the metal ions to interact with oleate acid radical, the metal ion octahedron layer exposures on the surface of a two layer silicate mineral, but the the oleate acid radical can not attach to a metal ion by replacing a –OH- that connects three metal cations in the same time, So the floatability of such silicate mineral is bad. The metal octahedron chain style of an island silicate mineral affects it floatability, the mineral exposures octahedron chain metals with two dangling bonds in two directions floats better than the mineral exposures octahedron chain metals with two dangling bonds in one direction.

Jan 1, 2003

By Stoyan N. Groudev, Ioannis Paspaliaris, Plamen S. Georgiev, Irena I. Spasova, Kostas Komnitsas

"The uranium deposit Curilo located in Western Bulgaria for a long period of time was a site of intensive mining activities including both the open-pit and underground mining techniques as well as in situ leaching of uranium. The ore was rich in pyrite and, apart from uranium, contained some non-ferrous metals. The mining operations in the deposit were ended in 1990 but since that time the deposit is a permanent source of acid drainage waters. The generation of these waters is connected mainly with the oxidation of pyrite and other sulphide minerals by the indigenous acidophilic chemolithotrophic bacteria.Laboratory and pilot-scale studies revealed that an efficient clean-up of the above-mentioned waters was achieved by means of passive systems of the wetland type. In 2001 a wetland was constructed in the deposit to treat a portion of the acid drainage waters which were discharged to a small ravine. This ravine reaches into the Teina, a small river that is a tributary of the upper reaches of the Iskar river.The wetland was constructed in the ravine and its bottom was located on intrusive rocks with a very low permeability. The rocks were covered by a 30 – 50 cm layer consisting of a mixture of soil, plant compost and crushed limestone. The wetland was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Carex and Poa as well as different algae were also well present.The acid drainage waters treated by the wetland had a pH in the range of about 2.5 – 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The watercourse through the wetland covered a distance of about 0.2 – 1.0 l/s."

Jan 1, 2003

By Shailin Lalloo, Allan B. Nesbitt

"Gravity separation by centrifugal equipment, particularly in the mineral processing industry is a novel approach of optimising product recovery. The manufacture and sale of centrifugal equipment by recently established companies is now beginning to have a significant impact on the industry. Some benefits of operating at increased gravity include: reduced environmental issues, a shorter lead time, lower capital cost and improved recoveries of elemental mineral before entering the grinding circuit.Of topical discussion is the use of centrifugal separators for the recovery of less valuable minerals that will form a greater proportion of the feed compared to traditional scalping circuits where the gold content is extremely low. This ultimately results in the centrifugal system having to have a greater mass pull. In addition, the relative density difference between gangue and valuable mineral is likely to be less and therefore modelling and optimisation of this separation process will be necessary. Some researchers have muted using fluidisation models to model the forces present in the separation zone of a centrifugal separator2. It is not unusual for the manufactures of centrifugal separation equipment to use fluidisation terminology to describe what happens in the separation zone. Most fluidisation models are based on the empirical/classic relationship between superficial fluid velocity and voidage postulated by Richardson and Zaki. However, no researcher has proved the effectiveness of this relationship in an increased gravity Environment."

Jan 1, 2003

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013

The 100th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 13th August, 1997. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents D.M. Jamieson, V.C. Robinson Fellows S. Goodwin, M.W. Johns Retired Fellows T.F. Muller, P.L. Nathan, N. Orsmond, R.J. Ortlepp, H.S. Sichel, K.E. Steele, W.B.L. Steuart, N.B. Vinson Member J.P. Hatfield Retired Members S.T. Baron, B.F. Pinder Retired Associate F.J.A. van Reenen In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1997

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

By D. Harrington

"Coal—mine explosions are accidents that can and should be prevented. In former years hundreds of lives were lost each year in the United States as a result of such explosions, but after 1932 the numerous precautionary measures adopted had reduced their frequency and severity 75 percent or more until in 1940 several very disastrous explosions marred the good record. Unfortunately, both the number and severity of explosions seem to be tending to increase compared with the relatively good achievement from 1933 to 1940. The requisites for an explosion are ever present in all soft-coal and many hard-coal mines. A certain combination of circumstances, such as a flame or an arc in a cloud of dust or in a body of gas or both may start an explosion at any time. The fact that the frequency and severity of explosions were lowered for 6 or 7 years is no guarantee that such freedom from explosions will continue, as the bad record of 1940 has shown, and underground workers should feel honor bound to exercise the utmost care so that they will not help to bring about the circumstances that will cause an explosion.Although mine operators bear the main responsibility for preventing explosions, miners can do many things to help. As about 9 out of 10 explosions begin at a working face, it is largely within the power of workers to prevent them. All miners should do their part willingly and should not defend a fellow workman from punishment, even from discharge, for disobeying necessary rules, whose disregard may cause the death not only of the safety-rule breaker but also of many of his coworkers.When a miner is careless and is injured some other way than by an explosion he may be the only one to suffer, but if his carelessness causes an explosion he not only endangers his own life but also that of every other man in the mine and possibly the lives of persons outside the mine.Experiments have shown that ignition of as small a quantity as 150 cubic feet of an explosive mixture of methane and air under certain circumstances can start an explosion that will traverse an entire mine. Thus, ignition of an explosive mixture of gas 1 foot down from the roof and 13 feet back from the face of a 12-foot entry might cause a widespread explosion if the right quantity and kind of dust were present. Many persons have ignited much larger quantities of gas without being killed, but they survived only because dust, confinement, and other conditions were not exactly ""right."""

Nov 1, 1940

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

Mineral formations, accumulated during technogenic activities greatly influence an economic and ecological situation in the Kola North. On the one hand, the dumps from extraction of mineral resources, tailing ponds of beneficating plants, ash dumps, wastes of metallurgical and mechanical engineering productions destroy the regionÆs environment and require taking certain measures and costs to bury or protect from weathering, oxidation, etc. On the other hand, technogenic mineral formations contain a lot of valuable scarce components. The amount of solid wastes increases annually, causing damage to ecology and economy. Researches conducted in recent years showed a possibility and economic expediency of comprehensive processing of wastes from different enterprises in Murmansk region and their use for production of new competitive commodity output, possessing high consumer properties. Thus, involving mineral wastes from Khibiny apatite deposits into hydrometallurgical industrial processing provides the basis for setting up a large beneficating-metallurgical complex. In this case ores and wastes from other deposits on the Kola Peninsula, containing titanium, rare, rare-earth and other valuable elements, may be involved into processing. Establishing such a complex will allow to organise a deep processing of natural resources, utilise some production wastes, improve ecological security and supply production with competitive output. Expanding the complex implies not only involving new mineral raw material into processing, but mainly deepening raw material processing, maximum utilisation of local natural resources and obtaining a wider variety of prime products.

Jan 1, 2002

By Steferson Ferreira de Oliveira

Desenvolvido nos últimos anos, o processo NDE, vem se tornando uma maneira promissora de usinar e nitretar simultânea a superfície de materiais metálicos. A Usinagem por Descargas Elétricas (EDM) é um processo de usinagem não convencional que tem grande potencial em aplicações de engenharia de superfície, ao melhorar a resistência superficial do material por meio de tratamentos termoquímicos, como por exemplo, a nitretação. Propriedades como: baixa densidade, boa resistência à tração (comparável à de muitos aços ligados) e excelente resistência à corrosão, possibilitam a aplicação do titânio e suas ligas nas indústrias aeroespacial, naval, química e automotiva e ainda no campo da medicina. Porém, raramente são usados como peças sujeitas ao deslizamento, devido a sua devido à sua baixa resistência aos mecanismos de desgaste abrasivo e adesivo e alto coeficiente de atrito. O tratamento termoquímico de nitretação pode solucionar esta restrição. Além de aumentar a resistência ao desgaste, o nitreto de titânio melhora a biocompatibilidade de suas ligas. O objetivo deste trabalho foi estudar a camada nitretada na liga de titânio Ti6Al4V por meio do processo de Nitretação por Descargas Elétricas (NDE), usando como fluído dielétrico solução de água deionizada e ureia granulada, como fonte de nitrogênio. Uma máquina de EDM por penetração foi utilizada no processo. Cobre e grafite foram utilizados como materiais dos eletrodos ferramenta. Foi avaliada a usinabilidade da liga Ti6Al4V com solução de água e ureia, relacionada aos parâmetros: taxa de remoção de material (TRM), taxa de desgaste (TD) e desgaste volumétrico relativo (DVR) para eletrodo de cobre e de grafite. Para caracterizar a camada nitretada foram realizadas microscopia óptica e medição de microdureza Vickers. A formação de nitretos na superfície foi avaliada por meio de difração de raio-x. Imagens metalográficas da seção transversal da superfície mostraram a formação da camada nitretada, devido ao ganho no valor da dureza. Os parâmetros relacionados à usinagem apresentaram valores que indicam um melhor desempenho quando se usa eletrodo ferramenta de cobre em relação à grafita. Nitretos de titânio foram observados no difratogramas da amostras nitretadas por NDE.

Oct 30, 2017