Search Documents

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By John F. Slonaker

This report is a review of current research being conducted in the United States which is intended to increase the utilization of coal ash. In order that this report be as timely as possible, the majority of information was obtained by direct comunication with the people listed in the references. Due to the magnitude of the flyash research program, some projects may be inadvertently omitted. Field research on flyash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University.1 This research is directed at determining the plant nutrients that are available in flyash as well as the quantities of flyash that can be applied to agricultural soil without adversely affecting plant growth, Coal mine spoil and refuse bank reclamation with power plant flyash is being demonstrated by United States Bureau of Mines, Morgantown, West Virginia.2 Numerous highly visible coal refuse piles and strip mine spoil banks contribute to air, water, and land environmental problems. Revegetation of several experimental sites with flyash from bituminous coal-fired power plants was undertaken in West Virginia and Pennsylvania. Conventional farm equipment was used at some of the sites while large earthmovers were required at others. The flyash served as a neutralizing agent, dilutent, and soil amendment to provide some nutrients which enhanced vegetation of the barren areas, Estimated cost of reclamation by this method is $300.00 per acre of previously leveled area. This figure can vary considerably depending upon the topography of the site, haul distance, quality of the soil and quality of flyash.

Jan 1, 1974

"For effective steel refining in the ladle (secondary steelmaking) the amount of steelmaking slag that is transferred from primary steelmaking must be limited, because the steelmaking slag contains iron oxide, manganese oxide, and phosphorus oxide. Adverse effects of slag carry-over include increased consumption of deoxidizers, phosphorus pick-up by the steel, and increased ladle refractory wear. Infrared imaging at longer wavelengths is an effective non-contact method to detect slag in the tapping stream. Various devices are used to shut off the tapping stream rapidly. These include slag darts, pneumatic slag stoppers, and slide gates for steelmaking converters, and eccentric bottom tapping for electric arc furnaces. IntroductionOxygen converters and electric arc furnaces are used for primary steelmaking. For both process types, the product (liquid crude steel) has a similar composition: largely liquid iron, with around 800–1000 parts per million (ppm, by mass) dissolved oxygen and low but significant concentrations of carbon, nitrogen, and phosphorus. The steel is tapped into a ladle, which serves as the refining vessel to adjust the final steel composition and temperature before casting.Some steelmaking slag is inevitably tapped with the liquid steel. The mass of steelmaking slag tapped with the steel is termed ‘slag carry-over’. Controlling and limiting slag carry-over from steelmaking is a primary requirement for clean steel production (Fandrich, Lüngen, and Wuppermann, 2008). Steel cleanliness refers to limiting the concentrations of dissolved impurities (such as nitrogen, oxygen, phosphorus, and sulphur) and of nonmetallic inclusions (oxides, sulphides, and nitrides) in liquid steel and in the final solid steel product. Of these, the strongest effect of slag carry-over is on the content of dissolved phosphorus in the liquid steel"

Jun 1, 2019

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operation, and critical in emergency conditions. This was evident during recent incidents at underground coal mines worldwide. Communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act of 2006. Evaluating the performance of these systems has proven to be dif?cult for mine operators, system manufacturers and regulatory agencies. The MINER Act requires operators to improve accident preparedness by developing an emergency response plan speci?c to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the U.S. Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky feeder communication systems. ? Fixed node-based communications and/or tracking systems. ? Wireless node-based communications and/or tracking systems. ? Medium frequency (MF) communication systems. ? Communication system peripherals. Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include through-the-earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial and hybrid technologies. To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is a need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

By M. A. Hermanus

This paper examines the occupational health and safety performance (OHS) of the South African mining sector against the backdrop of changes in the composition of the sector, international trends in OHS performance, and the agreement on OHS milestones and targets by mining stakeholders at the Mine Health and Safety Summit of 2003. Although OHS performance has improved, progress is slow and there is need for significant rather than incremental change if the targets are to be realized. Since 2003, fatalities and injuries are 20?25% short of annual milestones and not all commodities show consistent improvement. Statistics on occupational health impacts are unavailable, but noise and respirable dust levels are known to be high in mines, with much work lying ahead to address exposures at source. Trends in regulating and addressing OHS hazards are discussed with reference to the notion of ?systems-thinking? and the targets. Efforts to improve OHS and to respond to changes in the sector are constrained by a lack of training and consistency in risk management, guidance for junior, small and artisanal miners, and holistic approaches to risk. For example, treating risk holistically would involve taking proper account of contractors and women in the workplace, and attending to human factors and ergonomics.

Jan 1, 2007

By D Craw

At Reefton, mesothermal gold deposits occur in the Ordovician Greenland Group basement and bituminous coal deposits occur in overlying Eocene Brunner Coal Measures. These different resource types occur in close proximity to one another in the same topography, vegetation and climate. Both types of resources have been mined for many years and as a result historic mining areas discharge water with chemistry reflecting the mineralogy of the deposits. Coal measures release natural acid rock drainage throughout the region due to oxidation of pyrite in coal and associated sediments. Levels of acidity are increased in mining areas, and pH near three is common. Gold mines contain pyrite, arsenopyrite and stibnite. Discharge waters from these sites have pH near seven because of the high acid neutralising capacity of the basement rocks. Both coal and gold mining sites have iron oxyhydroxide precipitates in drainage waters. These precipitates are more abundant at gold mining sites, and one deposit is up to 5 m thick. Iron oxyhydroxide at coal mine sites contain Zn (up to 89 ppm), Ni (up to 10 ppm), As (up to 163 ppm), Cr (up to 23 ppm), Pb (up to 16), and Cu (up to 11 ppm). Jarosite group minerals have been identified in the coalmine iron oxyhydroxide, although most of the material is amorphous. Gold mine iron oxyhydroxide contains Zn (up to 353 ppm), Ni (up to 592 ppm), Cr (up to 17 ppm), Cu (up to 72 ppm), Pb (up to 29 ppm), Sb (up to 230 ppm), and this material is particularly high in As (up to 20 wt per cent). Most of the material is amorphous but distinctive zones (mm scale) are As rich (up to 30 wt per cent As oxide). Pharmacosiderite, K2Fe4(As04)3 (OH)5.6.3H20, is a secondary mineral in one deposit. These iron oxyhydroxide deposits are useful indicators for the metals mobilised into the environment by oxidation in the historic workings.

Jan 1, 2003

By Z. Lin, M. Isac, R. I. L. Guthrie

The kinetic and thermodynamic efficiencies of chromium recovery from the slag in an AOD process during the slag de-oxidation period with ferrosilicon is a complex process affected by slag basicity, temperature, the dissolution kinetics of the reducing agents, and intermixing of the slag/metal/alloy addition phases within the vessel. The present work focused on a study and simulation of the fluid dynamics and mixing behaviour of ferrosilicon additions in the AOD process for the production of stainless steel. In order to visualize the mixing behaviour, a two dimensional slice model of an AOD vessel was first built and filled with ZnCl2solution and then covered with silicone oil in order to represent the bulk liquid steel and slag phases, respectively. The injection of argon/oxygen process gases was simulated using air or helium. Particle trajectories and intermixing of the phases was monitored with a high-speed camera. To simulate the 75FeSi additions, glass spheres were used. A three-dimensional version of the AOD model was then constructed in order to confirm the adequacy of the slice model. Similar particle mixing behaviour was observed. Both models demonstrated that the ascending gas/liquid plume created two asymmetric mixing zones: a smaller rapidly re-circulating mixing zone adjacent to the side-wall locating the tuyere(s), and a larger mixing zone in the main part of the vessel. The process efficiency during the reduction period is governed by the thermal behaviour of ferroalloy as well as the mixing efficiency in the main large mixing zone. To enhance the recovery efficiency for chromium, small Fe-Si particles are suggested, given their wide distribution within the slag phase, and their large interfacial areas and rapid melting times for Cr2O3reduction from the slag. Keywords; modelling, ferrosilicon, chromium oxidation, AOD steelmaking.

Jan 1, 2004

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By S M. Aminossadati, R Bagherpour, F Hasheminasab

Mine ventilation is an essential part of underground mining operations used to provide fresh and cool air, as well as to dilute and remove contaminants from the work environment. This paper presents an overview of the ventilation and gas management systems in one of the underground coalmines in Iran: Parvadeh_1 mine. The mine is located in the Tabas coalfield in the South Khorasan province. It is the only fully mechanised mine in Iran utilising the longwall retreat technique. The mine produces 1.1 to 1.3 Mt of coking coal annually. The mine ventilation system currently utilises two 630 kW exhaust surface fans. The gas management system includes surface to in seam (SIS) predrainage boreholes. The underground mine is equipped with an underground gas reticulation pipeline that is connected to a surface plant for the production of methane gas. This study shows that the ventilation and gas management systems of the Parvadeh_1 mine are in line with the standards of Australian underground mines.CITATION:Hasheminasab, F, Aminossadati, S M and Bagherpour, R, 2017. An overview of ventilation and gas management systems in an underground coalmine in Iran, in Proceedings Australian Mine Vent Conference 2017, pp 41–46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By N. R. Williams

Black Mountain, a polymetallic base metal mine located in the Northern Cape territory of South Africa has been blessed with high grade economic ore for many years. Now that the Broken Hill orebody is nearing the end of its life, a lower grade orebody (Swartberg) is being exploited to supplement production from Broken Hill. In addition, ore from stopes in the upper levels of the Broken Hill orebody is considerably tarnished (oxidized). As a natural result, the remaining ore contains a higher percentage of magnetite, pyrrhotite and pyrite than in earlier years. Bismuth, cadmium and cobalt also occur in the ore in higher quantities. The life of the mine has been lengthened with the discovery of further deeper-lying ore reserves extending from the Broken Hill orebody suitably called the Deeps section. However, to bridge the gap between development of the new reserve and the exhaustion of the old reserve, these lower grade and tarnished (oxidized) ores have to be treated. The mine has had reasonable success in identifying unfavourable or problematic ore types and stockpiling them separately to blend in small quantities with more favourable ore. Bench and plant scale tests have aided identification of the various ore types and significant improvements in flotation metallurgical results have been seen. Copper, lead and zinc metal occur as sulphides in the ore. The mill consists of a differential and sequential flotation process that extracts copper concentrate, lead concentrate and zinc concentrate respectively with silver metal recovered in the copper and lead concentrates. This paper describes the ore blending strategy employed at the mine to maximize the econo-metallurgical efficiency of the operation.

Jan 1, 2001

By S. Witzke, J. Lehmann, H. Gaye

The modelling work presented here concerns Ni-bearing steels produced by Imphy Ugine Précision. In such grades, the contents of elements such as silicon or titanium must be precisely controlled by slag/metal treatments. The slag phase is described by IRSID slag model that has been slightly revised in order to better fit recent SiO2activity measurements in the low SiO2content domain of the CaO-Al2O3-CaO system. The metallic alloys are described by the unified interaction parameter model (UIPM). In this formalism, the interaction coefficients, giving the effect of nickel on Al, Si, Mn and Ti activities, have been determined by electrochemical measurements and/or extracted from industrial data on slag/metal treatments concerning a wide range of alloy compositions: [ ] Keywords: slag, Ni alloyed steels, activities, interaction coefficient

Jan 1, 2004

By E. Ulrich Klotz

It is difficult to predict accurately the capacity of driven piles in sand. In practice, this uncer­tainty either leads to conservative designs if the capacity is under-predicted, or worse, if the capacity is over-predicted, it can lead to severe foundation problems. One significant possible cause of the problem is that currently available semi-empirical design methods do not capture the fundamental mechanisms that govern the load capacity of driven piles in sands. As part of a recent research project at City University centrifuge tests on a driven model pile in sands have been undertaken. A fully instrumented model pile was constructed and pushed into samples of quartz and carbonate sand thus covering a wide range of mineralogies. Tri-axial tests were used to determine the fundamental patterns of behavior of the sands. This allowed a general framework to be established, in which the in situ stress:volume relationship is shown to govern the capacity of the pile. The paper sets out with a brief introduction of the experimental techniques used in the study. The results of the pile tests are discussed in detail with particular attention given to distribution of the radial stresses along the pile shaft. Existing design methods for piles in sand are then discussed in the light of the new understanding gained from the research, highlighting their deficiencies and suggesting an improved approach.

Jan 1, 2002

By C. J. Cutler

Metallurgical accounting for toll treatment smelters pose a number of challenges. Multiple feed stockpiles have to be accounted for as part of the monthly recovery estimation. Moreover, multiple metallurgical intermediates make up part of the in-process inventory, which also influence the monthly recovery calculation. Errors propagate from the measurements of volumes, assays, moisture fractions and bulk densities in the various material types through multiple steps up to the point where the final recovery is calculated. These errors contribute non-linearly to the variance in the final recovery estimate. This paper develops the mathematical formulation for variance propagation in toll smelting operations, including the effect of in-process inventory, assuming measurement biases have been eliminated beforehand. Operational data from a Southern African copper smelter is used for a case study. The method of propagation of variance showed that uncertainties in stockpile assays were the main contributors to variance in the recovery estimate. Variance in the volume and bulk density uncertainties contributed a secondary, yet significant, proportion to the overall recovery variance. It was determined, for the given case study, that the recovery variance depended on the calculation method used and that variance propagation via the two-product formula was smaller than recovery variances calculated via the standard recovery formula. However, the probability that the two product formula will give inaccurate (versus imprecise) results is significantly more due to the practical difficulty of equiprobable sampling of tailings streams from smelter plants (which includes materials such as slags and flue dust). Recommendations are made on how to achieve a reduction in overall uncertainty for toll treatment smelters. Keywords: metallurgical accounting, copper smelters, pyrometallurgy, variance propagation, errors, precision, sampling

Jan 1, 2006

Over recent years the trend in Australia has been towards the definitions of sustainable development which emerged from the 1992 Rio Summit of retaining a commitment to ecological integrity, but also incorporating social and economic dimensions of sustainability. Sustainable development may be seen as maintaining and enhancing:natural capital: defined as all natural resources, both environmental and those of traditional economic value; manufactured capital: made by human kind; including produced goods, infrastructure and built environment; human capital: defined as the health, well-being, intellectual capabilities and spiritual welfare of individuals; and social capital: defined as social relations and institutions within and between societies, their norms and functionality (Ameef, 2002). This paper will endeavour to assess the challenges and opportunities facing the professionals and their Institute in the minerals industry in Australia because the MMSD Global and Regional Australia Reports do not, in the authorÆs opinion, adequately address the æhuman capitalÆ input into the current or future development of the minerals industry, in particular, the sustainability of the professionalsÆ skills, knowledge and experiences in a global context.

Jan 1, 2002

By P. K. Frempong, S. D. Butt

"A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine.The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semivariogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates."

Jan 1, 2004

A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine. The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semi- variogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates.

Feb 1, 2004

By J. W. Langford

A more effective method of fracturing and chipping the formation is necessary to significantly increase the productivity of blasthole drilling with a roller cone bit. The conventional rotary blasthole bit engages the formation and initiates spalls, chipping and fractures in the formation at a rate dependent on the amount of pull down force applied by the drill. The rotary speed of the drill increases the number of fractures and creates drilled chips that are removed from the hole by the air circulation. An engineering project was motivated to develop a low pressure, low impact downhole percussion hammer to provide an overstrike force to a blasthole bit, in addition to the conventional pull down force and rotary speed. The objective of the project was to utilize existing rig air packages in the range of 50-110 psig and provide an overstrike force to the bit in the range of 1100-1500 impacts per minute. Laboratory testing performed on Barre granite achieved, on average, a 40% improvement in rate of penetration. This performance has been confirmed in actual blasthole drilling in copper and iron ores mines. During the testing phase, additional unexpected benefits have also been realized.

Jan 1, 2011

SAG Mill Grinding Design Versus Geometallurgy - Getting it Right for Competent Ores Smarter processing for the future, in the area of SAG mill design involves accurate grinding test data, completing final mill design in less than three months, and at a cost of less than US$80 000. More detailed variability testing on the other hand takes longer, is more expensive, and is used for throughput optimisation for an existing or newly purchased mill. This paper shows that SAGDesignTM testing is excellent for new SAG plant design due to relatively low cost per test and the ability to do more testing for a limited budget on larger projects. It also briefly examines a way to develop proper geometallurgical ore hardness information on every block in the mine model, from the more detailed analysis data.

Sep 13, 2010