Search Documents

By T. C. -M. Cheng

Iron removal and disposal in zinc plants has imposed a major environmental challenge to the industry. Among the existing options of precipitating iron as jarosite, goethite, and hematite, the Hematite Process seems to be the best candidate for the future development of a waste-free technology, because of its potential of producing saleable iron oxide residues for feed in iron-steel making industry. Unfortunately, under the current practice of the Hematite Process, it is not possible to produce iron residues clean enough to meet the specifications of the said industry. In this paper, the practice of industrial hematite precipitation and the relevant technical literature are reviewed with the objective to identify the critical processing parameters which are responsible for the contamination of hematite, particularly with sulfur and zinc. The analysis is conducted from a crystallization theory standpoint with emphasis given to the role of supersaturation with respect to the cleanliness of hematite precipitates.

Jan 1, 1997

By Ronald A. Crowson

Detailed stratigraphic studies of the overburden at North Carolina Phosphate Corporation new South Creek Mine have delineated several aquifers and acquicludes within the 30-meter-thick overburden section of late Pleistocene sands and clayey sands. A major aquifer occurs in the 10-meter-thick sequence of shelly sands of the early Pleistocene Croatan Formation. The water-charged Croatan sands thicken into a paleodrainage surface on top of the Pliocene Yorktown Formation, a major aquiclude. A three-phase dewatering program is projected: 1) improve surface drainage around mine perimeter to reduce both flowage into the pit and rainfall recharge; 2) use a wellpoint system to dewater the upper 8 meters; and 3) use recharge wells along the axis of the paleo- drainage to dewater the overburden below 8 meters.

Jan 1, 1983

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Bolivia has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW All useful substances of the mineral Kingdom belong originally to the State. The soil and subsoil are regarded as two distinct parts, the latter extending indefinitely in depth (Art. 2). The subsoil is under the dominion of the State, which may either abandon it to common use, grant it gratuitously to the owner of the soil, or alienate it, in return for an annual fee, to any individual or association that applies for it. (Art. 1-3.)

Jan 1, 1929

By R. W. Lewis

Spectrochemical procedures were developed using dc arc excitation for the determination, in parts per million, of 18 impurity elements in electrorefined beryllium and high-purity beryllium oxide. The metal samples were dissolved in dilute hydrochloric acid, evaporated to dryness, and converted to the oxide in a muffle furnace at 900° C. Germanium oxide was added as an internal standard for the determination of 15 of the elements, copper oxide for boron and molybdenum, and neodymium oxide for calcium. The average coefficient of variation was 11 percent with the exception of copper, which averaged about 43 percent.

Jan 1, 1962

The Prominent Hill copper-gold deposit is located approximately 150 km north west of Olympic Dam, on the southern margin of the Mount Woods Inlier in South Australia. Its discovery in November 2001 resulted from the application of a geological model developed from geological, geophysical and petrophysical data pertaining to the Olympic Dam deposit. The discovery has dispelled the notion the Olympic Dam may be unique, and that another deposit like it is unlikely to be found. The Prominent Hill mineralisation is hosted by haematite-matrix hydrothermal breccias, which have suffered extensive iron-sericite-silica alteration and overprinting. Copper, gold, barium, fluorine, uranium, cerium and lanthanum are all intrinsically associated with the hydrothermal iron. Breccias intrude an east-west striking, fault-controlled sedimentary succession, which is flanked to both the south and north by volcanic complexes. Many similarities between Prominent Hill and Olympic Dam are documented including geological setting, mineralogy, breccia styles, and alteration. Differences relate largely to the nature of the immediate host rocks. The similarities and difference provide key data for improving exploration models for this style of iron oxide copper-gold deposit, both within the Gawler Craton as well as globally.

Jan 1, 2004

By Patrik Fredriksson

Thermodynamic data concerning FeO-containing slags is of importance in ladle refining of steel. With a view to generate a set of reliable and self-consistent thermodynamic data for these slags, experimental determination of the activities of FeO in binary and ternary slags was carried out using the gas equilibration method involving CO-C02-Ar gas mixtures at steelmaking temperatures. The slag samples in Pt crucibles were quenched after the equilibration and subjected to chemical analysis. The thermodynamic activities of "FeO" in the slags were calculated from the experimental data. The results are incorporated into a thermodynamic description of silicate melts in the present laboratory. The model is based on a Temkin-Lumsden approach and is able to compute the thermodynamics of higher order systems from the lower order ones.

Jan 1, 2003

By Frank Ruskey

This report describes a computer program devised by the Bureau of Mines to model coal-mining situations where one or more panels encounter oil or gas wells. The program seeks in several hundred trials to evade the wells if possible or to minimize their influence by shifting or skewing the mine plan and/or adjusting the centerline dimensions of the entryways. Upon completion of computations, the program sorts the hundreds of models which have been tested, and lists the 10 best with their associated parameters. It also draws a mine plan of the best configuration, showing the entryways and crosscuts along with the "lost" coal remaining in the barrier pillars surrounding the various wells.

Jan 1, 1972

By S J. Neethling and, S J. R Simons

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, have been investigated. In this study two bubbles of equal size were formed and forced to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. Data of coalescence frequency and time is presented, as well as images of the coalescence events. The coalescence frequency was used to validate a parameter, Pf, known as the film failure frequency, used in a simulation model to predict foam height in a gas-sparged vessel. Predictions determined using Pf were then validated by experimentation.

Jan 1, 2005

By K Shannon, A Shaw

The Hilton and George Fisher deposits occur 22 and 24 km north of Mount Isa, NW Qld, Australia respectively. Both deposits occur as deformed Proterozoic, sediment hosted, stratiform orebodies hosting Pb-Zn-Ag (Hilton) and Zn-Pb-Ag (George Fisher) mineralisation. The two deposits are separated by approximately 2 km of strongly faulted barren shales, mudstones and siltstones along strike. Despite this, correlations between the Hilton and George Fisher deposits have previously been assumed on the basis of textural, lithological and geochemical similarities, but previously lacked specific details to prove exact stratigraphic matches.Feasibility drilling allowed broad correlations based on the position of siltstone pillars separating individual orebodies. However the position of continuous potassium-rich, siliceous and cross-fractured tuffaceous marker beds (TMBs) often used as stratigraphic markers within the Hilton Mine were initially unrecognised within the George Fisher stratigraphy where they are erratically silicified and often not cross-fractured resulting in correlations being difficult to prove. As a more detailed knowledge of TMB locations at George Fisher was gained it was possible to look for corresponding TMBs within the Hilton orebodies. Recent underground stope definition drilling at the two locations enabled specific TMBs, stratigraphic units and even individual sedimentary beds to be matched between the two locations, despite the large separation between mines.The correlation between the two deposits has implications for future exploration drilling north of George Fisher. If a specific stratigraphic horizon can be determined within one hole, positioning of further drillholes can be more accurately planned. The significance of having stratigraphic matches between Hilton and George Fisher also has implications for correlations with other Isa Valley deposits. Convincing preliminary TM and stratigraphic correlations have already been made between George Fisher and the Isa Lead Mine 24 km to the south.

Jan 1, 2002

The Khanong supergene-enriched copper resource, (~23 Mt at 3.0 per cent Cu), is one of several resources recently discovered in the intrusive-centred, sediment-hosted Au-Cu Sepon mineral field located in southern Lao PDR. The unusual style of hypogene mineralisation and unique set of conditions have resulted in the development and preservation of a supergene-enriched profile in this subtropical climate. Hypogene sulphide-rich mineralisation replaced calcareous cataclastite (fault rock) developed in the flat-lying, extensional, Khanong Fault. Spatially, the hypogene mineralisation was immediately out board of the skarn û hornfels Cu-Bi front and in board of sediment hosted Au-(As-Sb) mineralisation in a zoned intrusive-centred hydrothermal system. In situ supergene enrichment of the sulphide protore has resulted in a high-grade chalcocite-clay zone (~10.3 Mt at 4.6 per cent Cu) overlain by leached limonite-clay. A very high-grade in situ to exotic limonite-clay Cu-oxide-mineral zone is locally developed above impermeable dolomite at the base of chalcocite-clay zone. Exotic Cu-Mn-wad mineralisation developed for up to 1 km down the hydraulic gradient from the chalcocite-clay zone. Unique supergene enrichment conditions have resulted in the high-grade Khanong Cu resource in a subtropical weathering environment. The base of the currently active supergene profile coincides with the base of a flat-lying, pyrite-rich fault rock, dipping parallel to the hill slope, maximising Cu enrichment. Meteoric water has been channelled along subvertical faults and narrow horizontal subsurface zones. Low permeability of the fault host rock and footwall rocks has controlled the low volume and slow movement of groundwater required for supergene enrichment. Erosion has been slowed by the resistive ironstone and limonite-clay layer at surface, which assists in preserving the gentle slope over the chalcocite-clay zone.

Jan 1, 1999

Jan 1, 1970

By J. D. Morgan

The US economy grew steadily in 1989, reaching an annual rate of $5.3 trillion in the last quarter (US trillion=1012 ). The value of domestically processed, mineral-based materials rose 5% to $315 billion (US billion=109). The value of metals produced from US ores rose 14% to $11.6 billion, while industrial minerals rose 2% to $20.2 billion. Recycled scrap was valued at $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were $2.31 and $3.56/kg ($1.05 and $1.62 per lb) for copper, $1.58 and $2.57/kg (72 and $1.17 per lb) for aluminum, 77 and 97 cents/kg (35 cents and 44 cents per lb) for lead, and $1.58 and $2.09/kg (72 cents and 95 cents per lb) for zinc. Many mining and metal companies reported reasonable profits. Consumer demand strongly affects mining because the US economy is saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. 250 million US citizens already possess 172 million licensed motor vehicles and 100 million dwelling units. New car production fell 4% to 6.8 million units, while truck and bus production fell 1 % to four million units. New housing starts fell 9% to 1.4 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. Imports of crude and refined petroleum costing $50 billion exceeded domestic crude oil production. President Bush expressed "strong concerns about this country becoming further dependent on foreign oil." And the Department of Energy held a series of hearings around the country to develop ideas for a "national energy strategy."

Jan 1, 1990

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker's reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By S. Rash Ahmadi

Thin brittle coatings are deposited or developed on component surfaces for different reasons. In many practical applications the coatings are stressed by externally applied loads. Under such conditions, coating failure can occur. In this paper the probability of the extension of surface crack in coated materials due to cylindrical sliding indentation is analyzed. Contact loading problems typically result in multi-axle and strongly inhomogeneous stress fields near the contact surface. This property which strongly affects the stress intensity factors is taken into account in the failure analysis. Edge cracks were selected to model the actually accruing surface flaws. A suitable method is described for calculating the contact stress fields in coating and substrate. The coating is idealized as a brittle-elastic layer of uniform thickness, which is bonded to the surface of a half space. Method of linear elastic fracture mechanics are then used to calculate the load required to cause fracture in the coating.

Oct 1, 2011

By D. R. Lentz, C. J. Beaumont-Smith, S. H. Mcclenaghan

"Abstract - The Louvicourt Au-Ag-Cu-Zn-Pb sulfide deposit is hosted by a Middle Ordovician calc-alkaline sequence of aphyric rhyolite flows and associated fragmental rocks at the top of the Flat Landing Brook Formation. The Zr/TiO2 (average = 0.110) and Y/TiO2 (average = 0.021) ratios in the footwall felsic volcanic rocks are consistent with known values for the Reids Brook member. The deposit consists of two concordant lenses of semi-massive to massive sulfides, approximately 150 m long and up to 9 m thick, which represent a fold repetition of a single exhalative horizon. The deposit contains a geologic resource of 136 000 tonnes grading 1.2% Pb, 1.0% Zn, 0.4% Cu, 90.9 g/t Ag, and 0.96 g/t Au; the deposit locally contains elevated Au (2.9 ppm) and Ag (320 ppm) contents. A laterally continuous iron formation that contains barite caps the deposit, and is gradational vertically and laterally into laminated siltstone. The exhalite confirms the stratiform nature of this deposit, but a large percentage of sulfides occur as late replacements of altered felsic fragmental rocks in the footwall. Abundant examples of colloform pyrite and perlitic and spherulitic textures in volcanic clasts are well preserved. The base- and precious-metal content of the Louvicourt deposit is atypical of the Bathurst Mining Camp (BMC). Reported assay data (n = 27) indicate an average Pb/Zn ratio of 2.6, the highest in the BMC (average = 0.39). Lead exhibits a strong Spearman Rank correlation (r' = 0.92) with base metals throughout the sequence, indicating a preponderance of galena in both the stockwork and stratiform zones. The Ag and Au contents in this deposit are among the highest in the BMC and exhibit a Au-Ag- Cu-Pb association. Barite-rich exhalative pyrite exhibits a moderate Au correlation with Ag (r' = 0.77; n = 10) and Cu (r' = 0.76) and occurs in portions of the exhalative sulfides that are enriched in Pb. Chemical exhalative rocks are conformably overlain by trachy-andesitic volcaniclastic (possibly pyroclastic) rocks that are assigned to the Little River Formation. These are enriched in Nb (average = 38.4 ppm) and P2O5 (average = 0.17 wt.%), and have much lower Zr/TiO2 (average = 0.056) and Y/TiO2 (average = 0.0062) relative to rocks higher in the hanging wall. The intermediate volcanic rocks are conformably overlain by massive to pillowed basalt flows and related hyaloclastite that have Nb/Y = 0.60 and high TiO2 contents (average = 2.8 wt.%). This chemistry is consistent with rocks of the Brunswick Mines member (Little River Formation), except that these rocks are considerably enriched in P2O5 (average = 0.82 wt.%). This syngenetic exhalative deposit is unique for the BMC with a high Pb/Zn and elevated Au and Ag contents, as well as an epithermal signature (Sb-Ag-Au-Tl-Hg), analogous to high sulfidation volcanogenic massive sulfide deposits. Its intimate relationship with an emergent felsic dome (Flat Landing Brook Formation), chlorite-silicate-oxide-sulfide exhalite (locally hematitic), and the abundance of barite are classical features of many of the Kuroko deposits."

Jan 1, 2006

By King D

Recent field experiments in the United Kingdom (Buchanan, 1979) have shown that the in-seam technique is capable of detecting a 1m fault in a 3m seam, at a range of 280m and with a resolution of ¦40m. Comparable tests in Australian collieries are proceeding. Although the practicality of an implementation of the technique on a routine basis remains to be demonstrated, the potential of the technique for the prediction of outbursts clearly warrants detailed examination. This potential will,depend, inter alia, on the level and scale of variations in elastic (and anelastic) properties of bodies of coal undergoing stresses associated with mining. Available data, mainly from studies of the seismic properties of gas saturated reservoir rocks, confirm the intuitive view that stress increases give rise to increases in seismic wave velocity and decreases in wave attenuation, markedly at low stresses (as pore spaces close with little resistance) but less so as stress increases. Such increases are of the same order as aniso- tropic effects, but should provide impedance contrast sufficient for detection by in-seam seismic methods. At higher stresses, cracks form within the rock mass. Results from research on earthquake prediction provide some clues to the behaviour of sedimentary rocks sub- jected to large stresses. In particular, the

Jan 1, 1980

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By D. Zhao

High temperature deformation characteristics of austenitic 304L, and martensitic 410 and 416 stainless steels were investigated by conducting compression tests over a wide range of temperatures and strain rates (950-1250 C and 0.001-20 s-1). Flow behaviors of the three alloys were characterized. Optical metallography was performed to determine the as-deformed microstructures. The flow behaviors were related to microstructural phenomena during high temperature deformation. Dynamic recrystallization was responsible for the flow softening. Both dynamic and static recrystallization were operating, and the recrystallized grain size increased with increasing temperature and decreasing strain rate. Strain rate sensitivity was found to increased with increasing temperature and decreasing strain rate. No defects such as cracking and shear bands were observed at those test conditions. Preferred processing conditions can be selected by considering as-deformed microstructure and strain rate sensitivity.

Jan 1, 1994

By L. Telfer

Summary During Palaeozoic time, there were deposited in the Canadian Rockies four beds of phosphate rock, ranging in age from Mississippian to Jurassic. Two of these beds are of probable economic importance if some means of separating the phosphate from the gangue can be devised. All the more important beds of phosphate rock so far discovered are just behind the front ranges of the Rocky mountains, within fifty miles of the prairie lands of Alberta. Mining conditions are favourable, with an abundance of timber and ample power available. The phosphate beds are all of the sedimentary type, and they all occur, apparently, at the same stratigraphic horizons over a wide area. The conditions necessary for deposition evidently occurred at several different periods in geological time, and were widespread. The most important factor appears to have been the condition of the land surface surrounding the basin of de-position. Both oolitic and nodular phosphate were laid down under nearly similar conditions. Introduction Following the discovery of phosphate rock in Idaho and Montana, search was commenced in Canada to determine whether formations of similar age in the Canadian Rockies carried similar beds of phosphate. The most widespread search has been that undertaken by the mines department of the Consolidated Mining and Smelting Company of Canada. The following paper will discuss some of the results of this exploration.

Jan 1, 1933

By Dominic Parmantier, Jason Page

"In the past, the designers of DSM have analyzed various failure modes and then specified a minimum unconfined compressive strength (UCS) for the soil-cement. The specified minimum UCS reflected the compressive stress in the soil-cement under design loads and an appropriate factor of safety. With the increased use of finite element analysis for the design of DSM applications where allowable strain as well as stress are considered, there is a growing trend for designers to specify a modulus and occasionally a tensile strength for the soil-cement in addition to the UCS. This paper compares the relationship of modulus and tensile strength to UCS for soil-cement from a recent DSM project with unique testing requirements. These results are compared to published data. The case is made that designers should utilize published relationships to characterize the required strength and stiffness by a single acceptance criterion: UCS.INTRODUCTIONAs the use of DSM has increased in popularity so has the use of service state deformation analysis in lieu of more traditional failure mode analysis. Most DSM designers are interested in the appropriate modulus values and occasionally tensile strength values of soil-cement as well as simply the unconfined compressive strength (UCS) of soil-cement.Although there are numerous published correlations between the UCS, tensile strength and modulus of soil-cement, some DSM project specifications are produced which have acceptance values for tensile strength, modulus, and UCS. If this specification of multiple strength properties is consistent with the nature of soil-cement, then there is really no harm except for the expenditure of client money on unnecessary testing. If however the multiple strength properties specified are inconsistent with the material properties of soil-cement, then the specifications can create the expectation that the DSM contractor can somehow create a custom soil-cement with tensile strengths and modulus characteristics which are unachievable.This paper presents a brief summary of a project in Burnaby, B.C. which specified minimum values for the tensile strength, modulus, and UCS of the soil-cement. A comparison of those test results to published correlations between the UCS and the tensile strength is presented. Additionally, a comparison of modulus derived from two different methods of testing is presented along with a comparison to published correlations between UCS and modulus for soil-cement."

Jan 1, 2015