Search Documents

A number of gases, such as carbon dioxide, methane, water vapour, nitrous oxide, ozone and chlorofluorocarbons are transparent to incoming short-wave radiation, but are relatively opaque to outgoing longwave radiation. Variations in the concentration of these gases in the troposphere can alter the thermal balance of the earth's atmosphere. Outgoing terrestrial radiation which would otherwise escape to space, is trapped within the inner layer of the atmosphere, resulting in a greenhouse effect. It is estimated that at present greenhouse gases other than carbon dioxide, contribute about 50% to the greenhouse effect. However, in the future, the contribution made to the greenhouse effect by gases other than C02 will become increasingly more significant. Greenhouse gases arise from a wide range of sources and their escalating increease is largely related to an increase in the world's population, an increase in the standard of living of many areas and changes in lifestyle. The effect of increasing man-made greenhouse gases in the troposphere is unknown but it is proposed that it may increase temperature and may modify climate, agricultural response and land use. The sources of greenhouse gases are identified and found to comprise a wide range of activities. The contribution that coals use makes to the greenhouse effect is examined in detail. It is concluded that coals total contribution is small being about 10% of man made greenhouse gases. Envisaged expansion of coal's use will only cause a small increase in greenhouse gas emissions. Whilst developing technology for coal's use for power generation has the potential to reduce greenhouse gas emissions from new plants by approximately 25%.

Jan 1, 1989

By C. D. McMaster, John C. Hartley

Three systems that monitor ventilating fans are described . These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown .

Jan 1, 1964

By I. J. Jansen

Successful soil construction involves preparation of an adequate base, selection of high quality soil materials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experiments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construction. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By A Sadri, S Smith

In the metal and mineral industry, different empirical techniques are used to estimate the remaining thickness of the lining within an operating furnace. The disadvantage and costly factor when using these methods is that production needs to be halted. Hatch has developed an accurate and reliable technique based on stress wave propagation principles to determine the condition of the remaining lining whilst the furnace remains online and operational.The technique involves test data collected and compiled to generate 3D imagery used to assist operators and maintenance planning personnel with valuable information showing areas of metal penetration in the lining, remaining lining thickness, exact location of voids, cracks, poor contacts and deterioration due to chemical attack. In this paper, the principals of the AU-E technique will be explained both theoretically and practically. In addition, the use of ultrasound technology for determining the condition of copper cooling elements will be briefly addressed.

Jan 1, 2006

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

This study used artificial neural networks (ANNs) coupled with Gaussian mixture modeling (GMM) to analyze truck haulage data from openpit mines. The proposed weighted ensemble models performed better than benchmark models in predicting truck productivity, providing a new means of solving complex data and improving mine planning and decision-making.

Jun 1, 2023

By M. E. Hurst

SINCE 1934 there has been a marked revival of interest in the Porcupine district, especially in the eastern portion of the area, where exploration on the property of Pamour Gold Mines has indicated the presence of extensive gold-bearing deposits. Owing to the prevalence of overburden and the limited amount of exploratory work that has been done, little information is available as yet concerning the distribution and structural relationships of the rocks in the area to the east of Porcupine lake. In order to throw some light on the structural conditions in this section, a brief discussion of the sequence and character of the formations in the better known, producing section of the camp has been included. It should be emphasized that this paper is a preliminary study and that, consequently, the conclusions expressed should not be regarded as final. The writer wishes to acknowledge his indebtedness to P. C. Benedict, whose study of the geological relationships on the Foley-O'Brien property has made possible a fuller understanding of the structure in the central portion of the area. The writer also wishes to express his appreciation of the information and facilities placed at his disposal by R. M. Macaulay and C. D. Stevenson, of Pamour Gold Mines, and by A. Bell, of Noranda Mines, Limited.

Jan 1, 1936

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement.This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects.The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied (1). The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2017

On December 16, the General Services Administration (GSA) suspended weekly sales of surplus silver from the national defense stockpile because Congress approved the Defense Appropriation Act, which contained an amendment to halt silver sales. The amendment, introduced by Senator James A. McClure (R., Idaho), prohibits sales for 6 months while the impact of the sales and alternative methods of disposal are evaluated. The GSA sold 2 million troy ounces since sales started October 14. 46.5 million troy ounces were authorized to be sold during this fiscal year and an additional 58.6 million troy ounces were authorized to be sold over the following two fiscal years. The stockpile held 139.5 million troy ounces of silver when sales began in October. Brush Wellman, Inc., a vertically integrated producer of beryllium products announced plans to modify its Delta, Utah beryllium concentrate processing facility to utilize beryllium concentrates containing as little as 7% beryllium oxide. The company plans to invest $2.5 million for this modification with completion expected in mid-1983. Implementation of this plan to consume lower grade beryllium minerals will significantly increase world reserves of beryllium concentrates.

Jan 1, 1981

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

By A. CHESTER BEATTY

MAGNESIUM oxide is by far the most refractory of the common oxides, since it has a melting point of 5072 deg. F. as compared with 3110 deg. F., the melting point of silica (crystobalite) ; 3722 deg. F., the melting point of alumina (corundum) ; and 4127 deg. F., the melting point of chromite (Cr2O33FeO). Its large-scale use in the lining of metallurgical furnaces dates back to the latter part of the nineteenth century, when extensive deposits of magnesium carbonate were discovered in southern Austria in the province of Styria. Before the development of Austrian magnesite, calcined dolomite, a mixture of lime and magnesia, was used in basic steel-making furnaces. The lime in the dolomite was quite objectionable, since it slaked on exposure to the atmosphere, and dolomite therefore could not be made' .into permanent furnace bottoms or into brick. The Austrian magnesite, with its very low lime content, was free from these objections and soon displaced much of the dolomite. With the extensive development of basic steel-melting, the rise of the copper industry, and other metallurgical and chemical processes which dealt with chemically basic substances, the use of magnesite grain and magnesite brick increased rapidly.

Jan 1, 1931

By A. Andreas Hejja

Flow of slag and settling of matte in slag resistance electric furnaces are discussed in conjunction with furnace geometries, stirring action of the electrodes, buoyancy and electromagnetic effects. The rectangular electric furnace was regarded as a channel reactor and the mode of slag flow as a channel flow. The flow is affected both by buoyancy and electromagnetic forces, however the effect of electromagnetic forces is minimal. The flow velocity is made up of two components; (i) that developed by the action of the electrodes, and (ii) the bulk flow velocity determined by the smelting rate and the volume of the reactor. Slag samples were taken from various depths of the molten bath and were analyzed microscopically to determine the size and distribution of matte particles, The action of the electrodes was described by a simple mathematical formula indicating a balanced settling rate in the area of electrode action.

Jan 1, 1996

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By E. A. Almond

An attempt is made to explain the effect of stress on strain aging by examining the mechanism of yielding for a group of aged dislocations. The experimental results on which the theory is based indicate that a linear relationship develops between the aging stress and the discontinuous yield effect in a low carbon steel THE discontinuous yield effect that occurs in bcc metals after strain aging is usually explained by the interaction of interstitial atoms with individual dislocations. Attempts have been made to interpret the kinetics of strain aging in terms of interstitial segregation to nonrandom groups of dislocations1-3 but apart from Li's4 work little or no effort has been made to examine the effect of groups of aged dislocations on mechanical properties. It appears likely that such groups can be stabilized if a positive load is maintained on the specimen during aging5 and, furthermore, that the enhanced strain aging effect associated with aging under load might be due to the stability of these aged groups. The effects associated with this latter phenomenon have been described by Almond and Hull, Ref. 5, Figs. 2 and 3, and it is found that the upper yield stress, the lower yield stress, and the yield point elongation are increased by aging under load. The yield point elongation reaches a maximum value but the enhanced effect persists in the upper and lower yield stress values even after extended aging treatments when the general level of the flow stress curve rises. The flow stress, as measured at 8.5 pct total strain, however, is independent of aging stress. Almond and Hull5 showed that it was unlikely that the differences in mechanical properties could be caused by stress enhanced diffusion and they suggested that the effect was in some way associated with the different dislocation distributions that are obtained when specimens are aged with and without an applied stress. At that time no explanation was offered for the strengthening effect produced by stabilized dislocation distributions but additional tests have been performed to establish a quantitative relationship between aging stress and mechanical properties, and also to examine more closely the effect of varying the procedure for applying the aging stress. EXPERIMENTAL The material used was an iron wire containing 0.015 wt pct C, 0.002 wt pct N, and 0.006 wt pct 0. Tensile specimens with a 1 cm gage length and 0.08 cm diam were annealed at 850°C for 1 hr in vacuum to establish a grain diameter of 0.032 mm and then aged at 200°C for 24 hr. After this treatment the amount of carbon left in solution would be less than 10-4 wt pct, and ni- as aging time is increased. It is suggested that this observation, and effects that arise from varying the method of applying the aging stress, can be explained by a strengthening mechanism whereby dislocations are more difficult to move when they are aged in piled-up groups. trogen would be the main cause of strain aging. Tensile tests were performed in a hard beam machine at a constant crosshead speed of 0.02 cm per min and the specimen chamber was immersed in a temperature controlled silicone oil bath at 32" * 0.05"C. RESULTS All specimens were prestrained 5 pct before aging under stress and the results in Figs. 1 to 5 show the effect of aging time and aging stress on the following parameters ?UY = auy — ?F(5); i.e., the difference between the upper yield stress after aging,?uy, and the flow stress after prestraining 5 pct, ?f(5). ?LY = sly —sf(5); the difference between the lower yield stress after aging, ojy, and the flow stress after prestraining 5 pct. s8.5 = the flow stress at 8.5 pct total strain after aging at 5 pct strain. Varying the Loading Procedure. Three variations in the procedure for applying the aging stress were examined; i) After prestraining, the specimen was unloaded to a stress of 18 kg mm-2, aged at that stress, and then tested. ii) After prestraining, the specimen was unloaded to 2 kg mm-" then reloaded to 18 kg mm-', aged at that stress, and tested. iii) After prestraining, the specimen was unloaded to 18 kg mm-', aged at that stress, then unloaded to 2 kg mm- before testing. Specimens were unloaded or reloaded by decoupling a clutch in the drive transmission of the tensile machine. This enabled the crosshead to be driven manu-

Jan 1, 1970

By A. T. Jakubick, A. MacG. Robertson

This paper reviews key issues related to the placement of dry (soil) covers on extremely weak, compressible fine tailings. The design and construction of soil covers on such tailings often presents a formidable challenge to the geotechnical as well as the environmental engineer due to the low shear strength, poor traffic ability, and high settlement of under consolidated tailings at the time of reclamation. The geotechnical issues to be considered include: (1) consolidation of near-surface tailings to achieve strength gains, improve traffic ability, and allow safe placement of initial cover layer; (2) stability of tailings slopes during dewatering of tailings ponds and/or cover placement; and (3) long-term settlement of tailings and its impact on cover integrity and final surface shaping. The environmental issues to be considered include: (1) management of contaminated (free) pond water; (2) management of contaminated pore water expelled during tailings consolidation; and (3) management of (uncontaminated) surface water on top of the cover. This paper summarizes recent experiences gained in a large uranium tailings reclamation project. It is concluded that a careful consideration of both geotechnical and environmental issues during the planning stages greatly reduces the costs and environmental risks associated with fine tailings reclamation.

Jan 1, 2000

By F. P. Haver

A method to recover copper and elemental sulfur from chalcopyrite concen¬trate, using a ferric chloride leach, CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S, was reported by the Federal Bureau of Mines in 1971 (Report of Investigations 7474). Since that time, additional work has been done to improve certain steps in the procedure; that is, the recovery of sulfur from the leach residue, the recovery of copper and iron from the leach solution, and the regeneration of the leach solution. It was determined that over 99 pct of the elemental sulfur in the leach residue could be extracted at ambient temperature with an ammonium sulfide solution. Heating the pregnant solution precipitated crystals of rhombic sulfur (99.5 pct purity) and liberated ammonia and hydrogen sulfide for recycle. Copper with a purity in excess of 99 pct was obtained from the leach solution by electrolysis, using a diaphragm cell, with an energy requirement of less than 0.7 kW-hr/lb. Metal was deposited as a weakly adherent powder that could be easily dislodged from the cathode and withdrawn continuously from the cell in the form of a slurry. During electrolysis, part of the Fe(II) was oxidized to Fe (III) at the anode so there was no chlorine evolution. The leach solution was regenerated by direct oxidation of the spent electrolyte with air or oxygen in a turboaerator at 80° C. This precipitated the iron dissolved during leaching in an easily filterable form, Fe203.xH20, and converted the remaining Fe(II) to Fe(III).

Jan 1, 1975

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies. It discusses the concept of stress, Critical Incident Stress in emergency responders, and introduces the Critical Incident Stress Debriefing (CISD) process. It is suggested that, in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers, and more universally, to those responsible for developing emergency management plans.

By Olaf Hondrum

CHURN drilling equipment at Bagdad consists of two Bucyrus Erie 27-T model drills and one 22-T drill with gasoline engines. The drilling tools weigh approximately 1600 lb. The holes are drilled with 7-in. bits which are heated in an oil burning furnace and sharpened in an electrically powered bit sharpener. A service truck brings the bits to the drills and takes the dull bits back to the shop. The bits weigh around 250 lb. when new and are handled by drill crews without any mechanical handling device.

Jan 10, 1950

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global platetectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20o in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed

Jan 1, 1999

By S. M. Matthews

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ monitoring of behaviour has been carried out to confirm the mechanisms involved.

Jan 1, 1992