Search Documents

By Lawrence W. Teufel

A method to determine in situ stress directions and magnitudes from anelastic strain recovery measurements of oriented core has been used to determine the principal horizontal in situ stresses in the Rollins Sandstone in a deep well near Rifle, Colorado. The principal horizontal stress directions were determined directly from the principal horizontal strain recovery directions. The principal horizontal stress magnitudes were calculated from the principal strain recovery magnitudes, overburden stress, and Poison's ratio of the rock using a viscoelastic model. The accuracy of the in situ stress directions and magnitudes determined from anelastic strain recovery measurements was substantiated by a direct comparison with open-hole hydraulic fracture stress measurements. The anelastic strain recovery method predicted the magnitudes of the maximum and minimum horizontal principal stresses to be 54.5 MPa and 51.9 MPa, respectively; with an azimuth of N63ºW ± 8º for the maximum horizontal stress. The hydraulic fracture stress measurements yielded maximum and minimum horizontal principal stress magnitudes of 49.6 MPa and 46.8 MPa, respectively. The azimuth of the maximum horizontal stress ranged from N50ºW to N70°W.

Jan 1, 1984

By William Gleason

The Dulles Corridor Metrorail Project is a $3-billion project that will link Dulles International Airport with the downtown center of Washington D.C. by way of a single seat train ride. The project is mostly above ground, but it does include two short, yet complex, tunnels through the area of Tyson?s Corner. The project is being completed in two phases. The Dulles Transit Partners (DTP), led by Bechtel, was awarded the first phase, a $1.6-bil-lion phase that includes 17 km (11 miles) of track with five stations. At Tyson?s Corner, the project includes twin 730-m- (2,400-ft-) long, 6-m- (20-ft-) diameter tunnels. Bechtel is self-performing construction for the $1.6-billion design-build job. Gall Zeidler Consultants was hired by DTP as designer for the NATM tunnel portion of Phase 1, and Beton-und-Monierbau was hired as tunnel subcontractor. Tyson?s Corner is an affluent and congested area that sits 152 m (500 ft) above sea level. To get through the area, it was decided that tunnels would be the best option with the least amount of disturbance to the surrounding areas. However, with extremely shallow groundcover above some points as well as soft soil throughout, the tunnels are also the most complex aspect of Phase 1. About 213 m (700 ft) was constructed utilizing the cut-and-cover method. The remaining 518 m (1,700 ft) is being constructed using the New Austrian Tunneling Method, which integrates the principles of the behavior of rock and soil masses under load, and monitoring the performance of underground construction during construction. ?The tunnel only falls 2 m (7 ft) from one end to the other and we pass through two soil conditions, they are both soft ground,? said Dominic Cerulli, tunnel task manager for Bechtel. ?Soft ground is very tricky because you have to close the ring in a timely manner to minimize settlements at the surface. If you don?t close the ring quickly to achieve a round structure that?s good in compression, the tunnel could start necking and squatting and the ground above it will settle. We are under major roadways, so excessive settlement would be a bad thing.?

Jan 1, 2011

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established .R3 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resinsmay serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one. if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate. l7,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By S. N. Chadha

INTRODUCTION The work described here refers to the Genesee River Interceptor Southeast Project. This project is a part of the Combined Sewer Overflow Abatement Program, Phase I, for the Rochester Pure Water District, Rochester, New York. Our contract required the design of a 13,200-feet long main tunnel, 14 feet finished diameter, approximately 100-120 Feet below ground; drop shafts and diversion tunnels to deliver surface flow to the main tunnel; a gate chamber whereby the main tunnel is dropped 35 feet, and provision made for connection to the future tunnel in Phase II, as well as a host of other surface structures. Cross sectional dimensions for the structures involved varied from 16 feet circular to a 20'x50' horseshoe, in a competent rock formation consisting of Lockport Dolomite and Rochester Shale. In the construction of a rock tunnel, the problems of the tunnel designers are as follows: 1. To evaluate stresses in the rock as a result of excavation. 2. Design a temporary support system to prevent any rock failure during the period of construction. Design of this temporary support system is empirical. Design loads given by empirical relations are dependent upon the rock quality and size of opening. Temporary support system may either be steel frames closely spaced along the length of tunnel and tied together, in the case of poor rock, or, an even spacing of rock bolts in the case of competent rock. 3. Design a final lining for the service loads. Service loads, in our case of a water-carrying tunnel, are hydrostatic pressure due to ground water, deadweight of lining) pressure of contained water and time dependent rock loading. The constitutive properties of the rock are extremely complex because of discontinuities, pre-existing stresses due to overburden, material symmetries and changes of initial state associated with the process of excavation. The changes of initial state may be changes of stress fields along with the consequent yield of the material or the extension of existing discontinuities.

Jan 1, 1977

By J. G. Hadley

IN THE early stages of the depression the Utah Copper Co. realized that an unemployment problem would he created which demanded an intelligent and sympathetic solution. The company recognized that as many men as possible must be kept at work on a basis which would ultimately permit of the most efficient reabsorption of displaced labor. The company therefore determined to distribute available work among the greatest number of men and to that end adopted a system of rotating employees on a part-time basis. An employer requires a certain number of days' or shifts' work during the month. Obviously one employee working thirty days or shifts a month is equal to two employees each working fifteen. In principle, therefore, where two employees equally fitted to do certain work are available the work could be divided between them on an equitable basis and twice as many persons would benefit. A rotation plan on this basis was adopted by the Utah Copper, Co. on Jan. 30, 1930. Some variations of the orig¬inal plan have been made from time to time, the reasons for which will be discussed.

Jan 1, 1932

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

By S. C. Sun, A. M. Gaudin

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By A. M. Gaudin, S. C. Sun

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By César Macher

Dada la importancia económica y social que tiene la seguridad e higiene minera en el país, el objetivo del texto radica en crear las bases de un programa de higiene y seguridad que defina, evalúe, controle los riesgos industriales, como capacite a los estudiantes de ingenería de minas para mejorar los servicios que presta en la industria minera. El curso comprende cuatro capítulos y la distribución del tiempo de enseñanza en un periodo semestral. Entre los aspectos básicos del programa está la definición, significado económico y legislación sobre los riesgos ocupacionales; el conocimiento de los riesgos industriales referente a los agentes químicos, físicos, biológicos en los centros laborales; el muestreo y determinación de atmósferas polvorientas o control de riesgos, prevención de incendios y explosiones, normas de seguridad, y la forma de organización de seguridad e higiene minera. De otro lado, las presentaciones teóricas del curso se complementarán con problemas prácticos de la minería, material bibliográfico, y el desarrollo de prácticas con facilidades del Instituto de salud ocupacional, concluyendo con una serie de exámenes parciales teóricos-prácticos.

Jul 20, 1959

By C. R. Nailler

Two recently published papers describing the use of psychological tests for selection and placement of coal mine personnel have created considerable interest within the Coal Industry, one paper, published in the April 1957 "Mining Congress Journal," entitled "Personnel Evaluation and Training," discusses the use of tests by the Christopher Coal Company, The second paper, published in the "West -Virginia Coal Mining Institute's 1957 Report" and in the September 1957 "Coal Age," entitled "Testing to Select Better Personnel for Coal Mining Today," outlines Hanna Coal Company's test and selection procedures. Since these rather detailed sources are readily available, and to avoid repetition of the material in them, we will confine this paper to a very brief review of the essential steps already taken by these companies and a more extensive look at newer material. Briefly, the Personnel Managers, Mr. Harold L, Durrett and Mr. Albert M,. Rowe, of the Hanna Coal Company and Christopher Coal Company, in conjunction with Dr. Quin F, Curtis, Head of the Psychology Department of West Virginia University, developed two different groups oftests for coal mine personnel, The first group oftests was designed to assist in the selection of supervisors. These tests of the supervisory group were "The California Short Form Test of Mental Maturity - Advanced Series," which gave an I.Q. rating, and the second test is known as "The Minnesota Multiphasic Personality Inventory," which measures several personality characteristics, These tests must be given, grade, and interpreted by a person trained in psychological testing. As a result of testing all of Christopher's supervisory employees (seventy in number) by this method, and then comparing the individual results with the individual ratings of the foremen on the job, a so-called foremen's scale was developed. If this resulting foremen's scale had been used to select the foremen who were rated as, the best men in on-the-job performance, it would have correctly identified seventy-four percent of that group.

Jan 1, 1958

By Pengbo Chu, James Finch

Bubbles around 1 mm diameter provide the high interfacial area for capture and transport of hydrophobic particles in flotation. The formation of such fine bubbles is commonly achieved by addition of frothers that appear to simultaneously retard coalescence and promote break-up. High inorganic salt content in process water can substitute for frother. In this work we focus on the action of salt (sodium chloride) on formation of bubbles by break-up. An experimental setup that isolates break-up from coalescence was employed. A pocket of air is exposed to controlled mechanical turbulence to produce single bubbles by the induced deformation of the air and the events imaged. The presence of salt is shown to produce smaller bubbles than in water alone. Comparison with a similar study on frothers is made. The argument is advanced that the presence of frother and salt creates surface tension gradients at the air/water interface which add to the mechanical energy of the deformation and break-up process.

Jan 1, 2014

By G. A. Irons, D. Guo, D. Angheiina

To produce low-carbon (<30 ppm) steel in the tank degassing process, a ladle of steel with an oxidizing slag is placed in a vacuum tank equipped with bottom bubbling. The kinetics of this process are slow compared to the more prevalent RH degassing process, providing the impetus for the present work. There are several aspects to this work: water models of the fluid flow in the ladle; simulation of the decarburization (CO evolution) with C02 desorption in water; pilot-plant (60 kg) studies of the decarburization kinetics; mathematical modelling of the fluid flow in the ladle; mathematical models for each of the kinetic sites (plume, top slag and auto-nucleation); and full-scale trials. The results show that during the refining cycle the contribution from each reaction site changes, suggesting avenues for reducing cycling time and final carbon contents.

Jan 1, 2000

By Juárez T. Julio Cesar, Mendez R. Eliecer, Reyes P. Martín, Flores G. Mizraim Uriel, Teja R. Aislinn Michelle, Hernández C. Leticia, Reyes D. Iván Alejandro

The present study shows the characterization of a zinc concentrate collected at Hidalgo, Mexico, in order to identify its mineralogical species and to propose a leaching methodology for silver recovery. The results obtained by X-Ray Diffraction (XRD) show Sphalerite (ZnS) as the mineralogical matrix and silver into the specie proustite (Ag3AsS3). The techniques of Scanning Electron Microscopy-Energy Dispersive Microanalysis (SEM-EDS) and Polarized Optical Microscopy (POM) identified the presence of sulfides of Fe, Cu, Pb and Zn, in addition to silicates and feldspar. The proposed dissolution method of Ag(I) was carried out with [S2O3 2−] = 0.5 M and [NaOH] = 0.1 M to regulate the medium at pH = 9 for 12 h at 298 K. Oxidation of the concentrate was favored by injection of O2 to a partial pressure of 1 atm. Monitoring of the reaction was carried out by reading the [Ag] and [As] by AAS.

Mar 1, 2017

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By Robert H. Leach, C. H. Chatfield

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a stand¬ard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012