Search Documents

By R. W. Heins, N. Street

An investigation was made of the Rehbinder-Kuznetsov pendulum as an instrument to aid in the study of rock drillability and of the effect of surface active agents on rock drillability. The "critical weight", i.e., the pendulum weight at greatest sensitivity, was determined for several solids and it was shown that a change in surface environment changed the maximum value of the apparent hardness but not the critical weight, and the critical weight increased with increase of hardness of the solid used. Using silver halides as the solid material, and solutions of either silver nitrate or the appropriate alkali halide, it was shown that there is a hardness maximum at the zero point of charge of the particular silver halide. INTRODUCTION The development of relative hardness measurement by the method of damped oscillations, or what has been called the pendulum sclerometer, is due largely to the Russian workers P. A. Rehbinder and V. D. Kuznetsov and their co-workers.1,2 The apparent simplicity of the method has led to its use in a number of fields, particularly those where relative hardness has to be determined on a brittle solid. As will be shown, the simplicity of the method belies its complexities. THEORY OF THE PENDULUM SCLEROMETER The operation of the pendulum is quite simple. Make a sharp point such as a diamond, hardened steel or tungsten carbide, as the fulcrum of a pendulum, with the center of gravity of the system below the point of support. The attenuation of this pendulum is a function only of air friction, provided no fragmentation, breakage or other work is performed by the point. However, when the solid surface breaks or disintegrates under the point, and the latter penetrates the solid, part of the energy of oscillation is absorbed in the work of creating new surface, and the rate of attenuation increases. In the case of brittle solids, the point of the pendulum produces fragmentary particles, whereas the point produces plastic deformation in a plastic solid; but in both cases damping occurs. This pendulum damping is a function of the hardness or strength of the solid. Whereas a pendulum oscillating on a hard material attenuates primarily by air friction, in the case of a soft material, the points penetrate the surface of the solid, producing new surface, and the pendulum damps much faster. Thus the attenuation rate is a function of the hardness or strength of a material in both plastic and brittle substances. Russian workers initially used a single support for the pendulum, but this created many problems because of oscillation of the pendulum in more than one plane. A revised version used two points, or sometimes a prism as support, successfully confining oscillation to one plane. The version using two points was constructed and used throughout this investigation, making the recording of the attenuation as a function of time relatively easy. That both points should be in contact with the solid during the damping is implied. Rehbinder (c.f. Kuznetsov2) proposed that the hardness H as measured by this method could be expressed by a quantity which is inversely proportional to the relative initial rate of attenuation of amplitude. where H = hardness parameter (arbitrary units) a, = initial amplitude da/dt = rate of attenuation of amplitude with time. In the simplest case of damping with a constant logarithmic decrement, H can be regarded as a constant for the duration of the whole damped oscillation process. That is

Jan 1, 1966

By S. Mohanan, C. R. Kumar, S. K. Bhoja, T. Venugopalan

"A pressing issue that has often been the topic of discussion in iron-making operations in India is the high content of alumina in the country’s iron ore deposits. The presence of alumina has hampered production by affecting slag fluidity, and thereby the hot metal quality. Iron ores from Indian mines are generally rich in hematite, with traces or small amounts of goethite/limonite, kaolinite, gibbsite and quartz reported from time to time. In day-to-day production, emphasis is placed on checking the chemical analysis of product samples, but the true solution to the alumina problem lies in estimating the mineralogy of the ore samples. We developed a mathematical model, based on singular value decomposition, to predict mineralogy from classical chemical analysis. We then used X-ray diffraction patterns, scanning electron microscope analysis, and grain counting with an optical microscope to determine actual mineral compositions and to test the values predicted by the model. The results indicate that with regular calibration, the model can be used as a simple, fast and effective tool to predict on a regular basis the mineralogy of multiple samples.IntroductionIndian blast furnaces use high-grade iron ores (as lumps or as sinter) and coke (obtained from the destructive distillation of coal) as raw materials for the production of high-quality hot metal to be converted into different steel products through the Linz- Donawitz process. The iron ores are mainly sourced from the Singhbhum region of Odisha and Jharkhand states, the Bailadialla region of Chattisgarh state and the Bellary region of Karnataka and Goa states, and are mainly classified based on size as (1) lump ore (fed directly into blast furnaces), (2) fines (converted into sinter/pellets and fed to blast furnaces) and (3) slimes (< 0.15 mm; currently dumped in huge slime ponds). Any variation in the quality of the ores supplied results in variations in the production trends of hot metal."

Jan 1, 2015

By Eric S. Lindquist

Two microtunnel access shafts were constructed using the Cutter Soil Mixing (CSM) method in the San Joaquin Delta region of California, east of San Francisco. Unlike conventional slurry walls and diaphragm walls that utilize concrete, soil mixing relies on blending the soils in situ with a cement slurry to create a soil-cement wall. Cutter Soil Mixing technology utilizes two sets of vertically mounted cutting wheels rotating about a horizontal axis to produce rectangular panels of treated soil. Overlapping of the soil mixed panels enabled the construction of two circular shafts. CSM panels were constructed to a depth of 29 m (95 ft) for the microtunnel jacking shaft and to a depth of 19 m (63 ft) for the microtunnel receiving shaft. The site presented several challenges, including the high depth of treatment, the variable nature of the alluvial soils, and the high water table. This paper describes the CSM technique and presents the design, construction, quality control measures and advantages of using this method for this project.

Jan 1, 2010

By Federico Pagliacci, Claudio Asioli, Marco Chiarabelli

"""Rigid inclusions"" are a consolidation method that provides improvement of soft soils thanks to the installation of cylindrical columns made up of a material with significant and permanent cohesive properties, whose stiffness is 500÷5000 times greater than the surrounding natural soil’s. ""Rigid inclusions"" find their application in marginal areas (reclamations, polluted sites) to ensure stability of adjacent structures during construction of new buildings and to reduce the impact of natural disasters (liquefaction in the event of earthquakes, embankment collapse in the event of floods). This paper analyses the “rigid inclusion” construction method, related materials and equipment. Moreover, two performed projects will be illustrated. The first is the restoration of Lungarno Torrigiani Embankment in Florence, Italy. In May 2016, the Torrigiani embankment underwent a structural collapse causing a 3 m. displacement of the riverbank towards the Arno River. “Rigid inclusions” (with 300 mm diameter) have been used to re-compact the loose soil and create a stable working platform for the equipment. The second project illustrates the use of “rigid inclusions” (800 mm diameter and maximum depth of 36.6 m) to control the settlement of a new automatic cold store (30 m high with a 65 x 120 m foot print) for fresh frozen vegetables.RIGID INCLUSIONSIn general, the word ""inclusions"" means a type of consolidation that improves the strength of a soil mass through the inclusion of elements constituted by a material having better characteristics than those of the surrounding natural ground, to improve the overall mechanical characteristics of the treated soil. Inclusions are ""rigid"" when the material introduced into the ground has significant and permanent cohesive properties (concrete or cement mortar) and a significantly higher stiffness (500 ÷ 5000 times) than that of the surrounding natural ground.Typically, medium-small diameters (from 300 to 800mm) with low percentages of treatment (from 2% to 10% of the volume of soil) are employed, ensuring a high quality and consistency of the obtained product, both in terms of diameters and elastic modulus.According to the scope of the project and in urban areas, ""rigid inclusion"" columns can also be performed by means of small diameter drilling rigs (micropiles), weighing less than 20-25 tonnes."

Jan 1, 2017

By Robert Hamilton

Aur Resources is Canada&apos;s leading copper mining company with producing mines and development projects in North, Central, and South America. Copper production from Louvicourt Mine in Quebec, Quebrada Blanca, and Andacollo Mines in Chile had a record of 245 million pounds in 2001. Located 600 km North of Montreal, Louvicourt Mine is a joint venture between Aur Resources (30%), Teck Cominco (45%), and Novicourt (45%). Aur Resources is the mine operator with 280 employees working to produce a copper and zinc concentrate. In operation since 1994, the mine has produced a total of 12,606,000 metric tonnes of ore grading 3.6 % Cu, 1.5 % Zn, 26gr./m.t Ag, 0.9gr.m.t Au. This highly mechanized mine reached full production in August 1995 at 4,000 tpd. From 1996 to 2001, the average mine production rate was more than 4,300 tpd. The Louvicourt Mine continued its record of solid performance in 2002 and is expected to continue to do so for the balance of its 2.5 years mine life.

May 1, 2003

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Computational fluid dynamics (CFD) was applied to predict the average gas holdup and the axial gas holdup variation in a 13.5 m high cylindrical column 0.91 m diameter. The column was operating in batch mode. A Eulerian-Eulerian multiphase approach with appropriate interphase momentum exchange terms was applied to simulate the gas-liquid flow inside the column. Turbulence in the continuous phase was modelled using the k-_ realizable turbulence model. The predicted average gas holdup values were in good agreement with experimental data. The axial gas holdup prediction was generally good for the middle and top parts of the column, but was over-predicted for the bottom part of the column. Bubble velocity profiles were observed in which the axial velocity of the air bubbles decreased with height in the column. This may be related to the upward increase in gas holdup in the column. Simulations were also conducted to compare the gas holdup predicted with the universal, the Schiller-Naumann, and the Morsi-Alexander drag models. The gas holdup predictions for the three drag models were not significantly different. IntroductionColumn flotation is an important concentration technology that is used in the mineral processing and coal beneficiation industries. The growing interest in the use of column flotation in mineral processing has been attributed to the simpler flotation circuits and improved metallurgical performance compared to conventional flotation cells (Finch and Dobby, 1990). Flotation columns have also found other applications outside mineral processing, such as de-inking of recycled paper (Finch and Hardie, 1999).In column flotation, a rising swarm of air bubbles generated by means of air spargers is employed to collect the valuable mineral particles and separate them from the gangue minerals in a countercurrent process. Wash water, which is continuously fed at the top of the column, is used to eliminate entrained particles and stabilize the froth. The column volume can be divided into two sections – the collection zone in which the bubbles collect the floatable mineral particles, and the cleaning zone (or froth zone) where product upgrading is enhanced through the removal of unwanted particles entrained in the water mixed with bubbles from the collection zone."

Jan 1, 2019

By H. Ikeda

The new Onahama N0.3 tankhouse was put into operation early in 1973. This new tankhouse, which has a capacity of 90,000 metric ton cathode per year, is distinct in many important respects from conventional tankhouses. The major objectives in design were to simplify the construction and ope- ration for reduction of the costs for labor, interest and depreciation and also to reduce the copper inventory in the tankhouse by the use of conti- nuously-cast anodes. As a result, the investment cost was decreased by approximately 30% and the inventory cost by approximately 600, while the production per unit area of the tankhouse was increased by 80 - 100% as compared with the existing conventional-type tankhouses at Onahama. By abolition of cell inspection and maximum mechanization of materials handling the labor cost was decreased by as much as 80%. On the other hand, the new system has some disadvantages, such as increase in anode scrap ratio and increased cost of anode casting. The No.3 tankhouse system is, however, still at its starting point, while conventional methods have been continuously improved over the past years of operation. It is expected that the innovational ideas behind this system will serve as bases for a more efficient electrolytic refining system in future.

Jan 1, 1976

By Hugh S. Spence

IN MAY, 1930, G. LaBine and E. C. St. Paul, prospect¬ing round the southeastern shore of Great Bear Lake, in the North West Territories of Canada, discovered pitchblende at what is now LaBine Point. At the same time, they also found native silver in a small sheared break on an island lying off the point. Late in 1930, samples of the pitchblende were sent to the Mines Branch, at Ottawa. The material consisted of several fair-sized slabs of botryoidal pitchblende banded with a brownish quartz. A small amount of chalcopyrite was visible as small particles and fine veinlets, and the pieces were rather heavily stained a yellowish-green by secondary copper-uranium salts. Analyses were run in the Mines Branch Ore Dressing Laboratories on two samples, and small-scale concentration tests were made on one of them. The results of this work were published in a Memorandum Series report (No. 48) of the Mines Branch, in March, 1931.

Jan 1, 1932

By Hideki Minoura

"Two novel electrochemical techniques for the preparation of highly crystallized CdS film have been presented. One is cathodization of a conductive substrate in an acidic chemical bath containing cadmium salt and thioacetamide, where electroreduction of proton at small current densities induces a growth of highly crystallized CdS thin films, whose growth is not disturbed by the reactions in the solution phase. The other technique is electoreduction of aqueous Cd2+— SCN complex. An advantage of this technique lies in no formation of solid particles in the bulk, of the bath.IntroductionIn recent years much attention has been paid to materials preparation by solution processing because of its advantages in lowering the cost as well as the stress to the environment, as compared to the conventional gas phase techniques which unavoidably require high temperature and/or vacuum. We have been trying to explore novel techniques for preparing functionalized compound semiconductors by aqueous solution process. Semiconductors which we have been mainly focusing on are CdS and ZnO, which are important semiconductors finding applications in various devices. In the present paper, some of the techniques that we have recently established for the preparation of highly crystallized CdS will be presented.Methods of the CdS film processing in solution phase (wet process), which have been reported so far can be divided into two major groups; one is chemical bath deposition (CBD) in alkaline solution containing Cd2+ and thiourea 1)4) and the other is electrodeposition (ED) in acidic solution containing Cd2+ and thiosulfate ions - 5)-8) or organic solutions containing dissolved sulfur 9)-11)."

Jan 1, 2000

By Fuad S. Maayeh, Robert J. Evans, Paul M. Yavorsky

A description and capabilities of the Mine Roof Simulator at the Pittsburgh Mining Technology Center is illustrated for testing longwall roof support equipment. This unique Mine Roof Simulator has the capacity to exert 3 million lbs. of compressive force vertically and 1.6 million lbs. of force horizontally to simulate loads on hydraulic supports typically found in longwall mining. The supports that undergo testing are instrumented with strain gauges and photoelastic coatings such that critically strained areas become readily apparent. These critically strained areas are redesigned or retrofitted with appropriate reinforcement and retested. A data base will be accumulated from several support designs that will lead to an optimized design that will have the potential to reduce downtime by malfunctions of supports and thus increase productivity. A typical test procedure and analysis is given for a two leg 350 ton shield along with a description for placement of strain gauges, displacement gauges, and hydraulic pressure monitors for critical sites.

Jan 1, 1982

By M. K. Abel

"The Strathcona Mine is located in Levack Township on the North Range ofthe Sudbury Basin. The main orebody consists of pyrrhotite-pentlandite-chalcopyrite mineralization associated with an embayment of the footwall of the Sudbury Irruptive. A zone of massive chalcopyrite-cubanite-pentlandite mineralization occurs in a complex vein system in a series of mixed gneisses and breccias in the footwall. Vein widths vary from a few millimetres to 6 metres. In December 1979, this zone was estimated to contain 976,000 metric tonnes, with a grade of 9.31% Cu and 0.46% Ni. The vein system has a general strike of N 68°W at an angle of 60 degrees to the average strike of the footwall contact of the Irruptive. The dip of the vein system is 45 degrees sw. The strike and dip of individual veins in the system coincide with the directions that would result if a compressive stress had acted in a direction normal to the footwall of the Sudbury Irruptive, producing a conjugate set of fractures. The strike of the Irruptive at the Strathcona Mine is parallel to the long axis of the basin.IntroductionThe Strathcona Mine, owned and operated by Falconbridge Nickel Mines Limited, is located in Levack Township on the northwest rim of the Sudbury basin (Fig. I) . It is one of a group of nickel-copper sulphide ore deposits present along an 8.2-km section of the North Range of the Sudbury Irruptive. In the mines of the North Range, subunits of the Irruptive, going from hanging wall to footwall , include felsic norite, dark norite and dark norite breccia. The footwall complex at Strathcona includes the late granite breccia, which hosts a large proportion of the nickel-copper ores, and a compositionally variable group of brecciated and migmatized rocks, herein referred to as the feldspathic gneiss complex. It is within this latter group of rocks that the vein system of the Copper Zone occurs."

Jan 1, 1981

By Y. Y. Liu, H. M. Domanus, W. T. Sha

"Casting is fundamental to manufacturing of many types of equipment and products. Although casting is a very old technology that has been in existence for hundreds of years, it remains a highly empirical technology, and production of new castings requires an expensive and time-consuming trial-and-error approach.In recent years, mathematical modeling of casting has received increasing attention; however, a majority of the modeling work has been in the area of heat transfer and solidification. Very little work has been done in modeling fluid flow of the liquid melt. This paper presents a model of fluid flow coupled with heat transfer of a liquid melt for casting processes. The model to be described in this paper is an extension of the COMMIX code and is capable of handling castings with any shape, size, and material. A feature of this model is the ability to track the liquid/gas interface and liquid/solid interface. The flow of liquid melt through the sprue and runners and into the mold cavity is calculated as well as three-dimensional temperature and velocity distributions of the liquid melt throughout the casting process.IntroductionBower et al. (1), in their 1969 review of the evolution of some of the casting techniques, stated that:""The evolution of technology requires alternatives to be available so that choices can be made that lead to changes. The role of solidification science and other disciplines related to casting technology is to develop a better understanding of process and product, so that a wider range of alternatives is possible.Alternatives, whether from science or from invention, must lead to improvements in casting ""utility."" Utility, or economic advantage, must include consideration of total system costs, and final product value. The cost of materials, melt processing and finishing should be optimized with casting costs, since all are part of the production system. It is the favorable relationship between total processing costs and product value that makes a change in casting technology viable, but the best change is not possible unless technology has provided an understanding."""

Jan 1, 1986

By Rob Famlield, Gavin Yuill, William Birch

The Blasting Research Group at the University of Leeds, in the United Kingdom, continues to be highly active in the area of the environmental impact of blasting. In recent years a major part of this research has been concerned with the use of linear superposition. This technique relies upon the assumption that all the holes in a blast produce identical vibration signals. Previous work at the University has shown that this assumption is not sufficiently robust to be generally applicable. This is due to a number of factors of which the key variable appears to be dynamic confinement

Jan 1, 2002

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997

By Miroslav Raudensky, Kallol Bera, Jaroslav Horsky, Jee G. Chang, Ampere A. Tseng

"A combined experimental and finite element approach to study the local heat transfer coefficient is presented in this paper. The heat transfer coefficients at different cooling regimes in a roll are quantified by an inverse heat conduction technique; the heat transfer phenomena involved are then discussed. A discussion of the application of the heat transfer information found in the present study for better design of a roll cooling system is also included. Finally, an identification of areas where further work is needed is presented.IntroductionIn metal rolling processes, the roll is used as a tool to deform the workpiece at very high speeds. As shown in Fig. 1, the heat transfer phenomena involved in the process are complicated by the interaction between the roll and the strip, mainly including 1) the heat transferred from the workpiece to rolls in the contact regions, 2) the heat created in the interface due to the deformation of the workpiece and the friction between the workpiece and roll, and 3) the heat removed by watercooling as well as the ambient air. All of these transport phenomena occur at extremely high pressure, high speed, and high heat flux; these make the control of the roll temperatures an extremely challenging problem.In hot rolling, proper cooling of rolls can lead not only to improve the roll shape quality by controlling the thermal crown of the roll, but also to extend the roll life by minimizing the thermally induced stresses [1,2]. Also, knowledge of roll temperatures can contribute to insights about the roll/workpiece interfacellubricant behavior, and lead to the desired surface condition of the workpiece. Therefore, adequate roll cooling or control of roll temperatures is of critical concern to mill designers and process engineers. In order to have proper operation of the process, a good understanding of the influence of cooling practices on the roll is essential [3]."

Jan 1, 1994

By A. E. Ketler

The Bureau of Mines Research Program has defined per coal miner&apos;s illumination needs. Due to similarity in the environment in which coal and Hardrock miners work, coal mine illumination technology has been applied to Hardtack room and pillar mines.

Jan 1, 1977

By B. Denby

Recent advances in Virtual Reality (VR) technology have resulted in major opportunities to improve safety training of mine workers, supervisors and managers. The hazardous nature of both surface and underground environments limits the type of safety training that can be carried out. VR offers the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 1998

By Mark Van Dyke, Ted Klemetti, Jake Beale, Zoheir Khademian, Joe Wickline

In 2016, a 3.7-ML magnitude event caused by mining activity occurred at a longwall mine in southwestern Virginia which was recorded by the United States Geological Survey (USGS) and felt by local residents. The event was the largest of its kind since a global mine design change by the operator was instituted in 2008 following three large events in 2005, 2006 and 2007 (3.4, 4.3, and 3.4, respectively). Two of the three pre-2008 events (2005 and 2007) damaged ventilation controls in the mine which fueled a mine fire. In 2016 the mine’s management requested researchers from the National Institute for Occupational Safety and Health (NIOSH) to access geological data and determine what parameters could possibly lead to events of a magnitude of 1.0 ML or greater. Evaluation of 2,152 geological data points and modeling revealed three major geological factors in common with the majority

By S. Oppenheimer, P. Au, R. M. Kearsey, J. Tsang, E. McDevitt

A new superalloy, ATI 718Plus® Alloy (718Plus), has been developed to have a 55oC higher temperature capability over the traditionally used Alloy 718, while maintaining favourable processing characteristics and intrinsic raw material costs. The fatigue and dwell-fatigue behaviour of four microstructural variations of 718Plus are evaluated and compared to Waspaloy: 1) standard heat treated condition (HT1), 2) standard heat treated condition with thermal exposure at 732ºC (1350ºF) for 1000 hours (HT2), 3) fine grain condition with a modified d phase (HT3), and 4) fine grain overaged through modified heat treatment (HT4). The results show that the steady-state fatigue crack growth rates of each microstructural variation and both alloys are identical, with all of the 718Plus variations showing a clear advantage over Waspaloy in the fatigue crack threshold regime. Dwell-fatigue results show that Waspaloy has better resistance to crack propagation under dwell conditions; however, optimization of the precipitate phase shows vast improvement in the dwell-fatigue resistance of 718Plus.

Jan 1, 2010

By Edmund J. Korber, Donald E. Raab, Frank A. Burns

During the early 1960s, the advent of self- advancing longwall roof supports triggered serious consideration by Bethlehem management to introduce the technique of longwall mining at one of our central Pennsylvania coal mines. Although longwall mining was initially justified as a means to cope with the severe roof conditions at our Mine 32 (Watson, B., 1971), the result of the endeavor has been a consistent and reliable level of coal production, first from Mine 32 and then later from Mine 33, over a period of fifteen years. Longwall production from the Cambria Division has been the mainstay of the low volatile coal required by Bethlehem Steel for steel production. Let us review the events that led to this accomplishment, as well as where we stand today.

Jan 1, 1981