Search Documents

LANDSAT imagery has renewed interest in linear features first recognised by E. S. Hills in a physiographic model of Australia. Certain of these lineaments are aligned with structures which control mineralisation.Lineament guidelines are potentially useful in many poorlyexposed areas if they can be recognised early enough in exploration and drilling programs leading to mine development.A case history based on the Charters Towers Gold Field indicates that lineament guidelines can be established early enough to guide development ofnew mines. The position of the Charters Towers Lineament was known as early as 1956. Subsequently, more detailed publications identified and classified associated lineaments which provide intersections correlated with gold occurrences. The discovery of a significant orebody at one of the most prominent lineament intersections came in 1975. Mine drilling has confirmed the influence ofintersecting structural trends indicated by lineaments but not by previous regional mapping.Recent gold discoveries south of Charters Towers lie in a grid of prominent lineaments. The development of mines about Charters Towers will provide additional understanding of relationships between centres of mineralisation and lineament intersections. This understanding may in future be sufficient to encourage exploration for a new generation of concealed gold deposits in northeastern Queensland.

Jan 1, 1986

By R. Wang

"Under high stress conditions, rock bursts, borehole breakouts, and spalling events are common phenomena that occur around underground openings. In general, together these three phenomena represent brittle failures of an intact rock mass; however, individually they reflect different failure modes under high stresses. After analyzing and comparing the stress-to-strength criteria for rock bursts, borehole breakouts, and spalling events, proposed by previous researchers, it is found that these brittle failure phenomena share common stress-to-strength prerequisite. The stress-to-strength preconditions for brittle failures can be defined by the ratio of the maximum tangential stress around an underground opening to the uniaxial compressive strength (UCS) (s?max/sci) or by the ratio of the maximum far-field principal stress to the UCS (s1/sci). Both these indicators can be used to reflect the same stress preconditions. For s?max/sci, a ratio of 0.4±0.1 represents the critical stress requirement for brittle fracture. However, for s1/sci, a ratio of 0.15±0.05 should be considered as the critical stress requirement. Numerous engineering case studies and analysis of rock mechanics based on the Hoek-Brown criterion also verify these two stress-to-strength preconditions. Here, these two indicators are presented with an error range because complex rock mass quality ratings, lithology, and geotechnical conditions have profound impacts on the stress-to-strength preconditions for brittle failures. INTRODUCTIONHigh stresses are one of the most important factors that must be considered when undertaking underground rock mass projects (Kaiser et al., 1998). Wang et al. (2009) reviewed current progress in the evaluation of high stresses and their corresponding criteria. However, after clarifying the definition of high stress, civil engineers need to understand the deformation and failure behaviors of rock mass around an opening under high stresses. Under high stress conditions, the deformation of rock masses around an opening can be categorized into two groups, i.e., severe brittle failures (or rock bursts) and compressional plastic deformation of the surrounding rock mass, as indicated in Figure 1."

Jan 1, 2015

By Mark Sheppard

[Considerable research work hi been done on secondary crushing and coarse and fine grinding, and the literature on the general subject of Crushing contains many references to the work of investigators on the laws governing end the factors entering into the economical production of fine materials. However, little information on primary crushing in available The literature deals mainly with problems and practices in ore dressing, end in this field the engineer or investigator is concerned largely with the production of fine material and the unlocking of minerals in the ore. Under such conditions close control of screen sizes of primary-crusher products is a secondary consideration and has received very little attention.]

Jan 1, 1938

By H. W. Gillett

CLYDE WILLIAMS has reminded me that in the fall of 1929, gave, in MINING AND METALLURGY, an account of the hopes and aspirations of Battelle Memorial Institute, which was then just swinging into initial operation; and that therein I remarked that B.M.I. should stand, as well, for Better Metallurgical Industries, since helping to better them was the Institute's aim. So he has suggested that some of the betterments of the past fifteen years might well be listed. A yearly summary of progress comes pretty close to the ultimate in futility, for everything proved of value in that year had its inception in earlier years, and everything really new has still to be proved. Plenty of things hailed as wonderful achievements for that year, by some enthusiasts invited to contribute to the summary, turn out in later years to be inglorious flops. But over a decade and a half, betterments that are really such become self-evident, and recounting some of them can be done without guesswork or wishful thinking. An inventory of what was known and utilized in 1929 compared to what is now known and used is not too hard to make. Perhaps the most clear-cut picture of what is known and used at a certain date is drawn by the handbooks, textbooks, and equipment catalogs of that date, with scientific periodical literature forecasting what knowledge may later be used when it is verified and assimilated. The tools available for production or for research limit the application of old and the finding of new knowledge.

Jan 1, 1945

By Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY?s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By Camila Ferreira da Silva

O presente trabalho descreve a síntese de um vidro de constituição inovadora, elaborado com adição de escória de distribuidor em sua composição. Suas propriedades ópticas foram determinadas através da realização da caracterização elipsométrica. Em virtude da vasta gama de composições vítreas possíveis e visando o reaproveitamento de um coproduto siderúrgico, propõe-se a utilização de escória de distribuidor para a composição de um novo vidro. Efetuou-se a análise superficial via microscopia confocal. Posteriormente ao preparo da superfície, as propriedades ópticas foram obtidas através da medida dos parâmetros elipsométricos tan(?), cos(?) e por conseguinte a obtenção preliminar do índice de refração e do coeficiente de extinção.

Oct 30, 2017

A new lead refinery with a. capacity of 230,000 tons per year com-menced operation at*Port'Plsie in October, 1959. This plant' superseded the refinery which had operated from 1933 with the advent of thecontinuous lead refining process. The incorporation of new equipment following local metallurgical developments, together with the overseas demand for lead of extremely low antimony content, created difficulties in operating the original plant. The new refinery project was under-taken to cover this disability and to gain the full advantage of the new processes.Desilverising and softening are carried out in units identical in size to those used previously. Metallic'zinc is now recovered from the entire output of desilverised bullion by vacuum distillation. Final refining is then carried out by batch'treatinent with caustic soda yield-ing lead of purity previously unattainable at Port Pirie.These two processes have replaced continuous dezincing by oxidation, a high temperature process which caused large quantities of lead and antimony to be recirculated. As the final stage is a .batch process the product composition can be.checked before casting. Individual batches can be adjusted to produce special alloys to,consumer's specification.Improved casting equipment has allowed the quantity production of pigs of good physical characteristics either as 56 lb bars or 2000 lb pigs. This, together with the high purity of the lead, has assured the B.H.A.S. position in world markets.Automatic control systems have been extensively employed particularly on the vacuum dezincing unit.The anticipated financial benefits have been achieved mainly by a reduction in the tonnage of recirculated materials, a smaller labour force, and reduced maintenance requirements.

Jan 1, 1963

By G. B. Shea

In the search for possible future sources of petroleum products, the recovery and utilization of bitumens from the large outcropping deposits of bituminous sandstones in the United States have been under study by the Bureau of Mines for the past several years. The results of laboratory research in the adaptation of the hot-water separation process to recovery of bitumen from bituminous sandstones were reported in an earlier publication, on the Edna deposits near San Luis Obispo, Calif. This publication included analytical data on the cracked products and asphalts obtained from the extracted bitumen and on the cracking and distillation of the bitumen. Comparable hot-water separation tests have been run in the San Francisco, Calif., laboratory of the Bureau of Mines on quarry samples from the large deposits of bituminous sandstones near Vernal and Sunnyside, Utah. The bitumens were isolated from the extracts of the separation plant and analyzed at the Petroleum and Oil-Shale Experiment Station of the Bureau of Mines, Laramie, Wyo. Part I of this report summarizes the general characteristics of the Vernal and Sunnyside deposits and discusses the hot-water separation process as applied to those bituminous sandstones and the results obtained. The separation tests showed that these bituminous sandstones also respond to treatment by the hotwater method of separation. The bitumen in the Vernal sandstone was extracted more readily by the action of hot water than was the Edna bitumen, which greatly simplified plant operation. The Vernal sandstone contains no water-soluble iron compounds, such as were found in the Edna sandstone, and, therefore, required no preliminary water washing. Recovery of bitumen from the Vernal sandstone was about 96 percent.

Jan 1, 1952

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

THE object of the air-tight stopping is either to prevent a current of fresh air from getting into the fire area, or to prevent an escape of fumes and gases from the fire area into the workings of the mine. In the former case all is "plain sailing," but in the latter case there are certain difficulties to be overcome.In the Broken Hill Proprietary mine there were two styles of stopping used during the last fire-brick and bag and the following were the chief points that determined the use of one in preference to the other:-If the required stopping were to be more or less permanent, bricks were used, also if the area to be blocked were large-bricks being so much lighter and easier to handle than bags filled with -skimps. If, however, the air contained much gas, a bag stopping was put up. Great difficulty was experienced in getting essentially surface men, such as bricklayers, to work where there was the; slightest trace of gas; miners, however, would willingly do the work, and a bag stopping could be built without skilled labour.In old drives and gangways, where there was the liability of settlement, the bag stoppings were preferable to brick. The slightest movement around the sides or foundations of the latter would cause cracks, thus rendering the brick stopping useless;whereas, in the former, there was a certain amount of elasticity.

Jan 1, 1909

By Alfonso Rizo-Patrón Remy

El objetivo del siguiente trabajo es señalar un método que permita la recuperación económica de metales preciosos como el oro, plata y otros metales básicos (tales como plomo y cobre) de sus respectivas menas naturales y de los concentrados o relaves que los contengan. Para ello, se utlizará dos formas de aplicación: La primera se da en el tratamiento por cianuración de las menas, donde el carbón mineral es el medio precipitante de los metales disueltos. Mientras que la segunda ocurre cuando el carbón ha sido separado de las pulpas cianuradas, conviertiéndose en un agente reductor de los metales de fundición. De forma tal que se logra una recuperación integral de los metales preciosos y básicos en las barras de fundición.

Jun 20, 1954

By Jr. Smith

The equilibrium compositions of product gases for mixtures of air with methane, propane, or ethylene at and around flame temperatures are reported. For each hydrocarbon, compositions are given for five fuel-to-air ratios--two lean, two rich, and one stoichiometric--at five pressures, from 1 to 20 atmospheres, and at an ambient temperature of 25° C.

Jan 1, 1965

By S. Hlajoane, L. S. Mokhahlane

The demand for rare earth elements has increased around the world due to their application in a variety of technological advancements. Previous studies have evaluated the potential of the rare earth elements and yttrium (REY) hosted within the Permian coal deposits of the main Karoo Basin (MKB) in Southern Africa. However, not a lot of scientific research has gone into the Triassic coal deposits. The Triassic coals in South Africa were the first coals to be exploited for their thermal use in the 1880s, but the discovery of the higher rank and more abundant Ecca coal deposits led to the Triassic coals remaining largely unexplored. The demand for rare earth elements has sparked interest in these coal deposits as potential sources for valuable minerals. Late Triassic coal deposits in Lesotho have previously not been well documented and these low-rank coals can be a potential source of rare earth elements. This study aims to characterize and evaluate the potential of REY in the Taung coal deposit, southwest of Lesotho. Coal and associated argillaceous samples from the Taung coal deposit were analyzed using microscopic petrography for coal characterization and an inductively coupled plasma mass spectrometry (ICP-MS) to determine the amount of rare earth elements. Taung coal is classified as middle medium rank D bituminous coal. The total REY content in Taung coal and its associated rocks range from 162.9 ppm to 855.1 ppm, which is significantly higher than the upper continental crustal (UCC) average. The average critical REY concentration of samples from the Taung coal deposit is 189.4 ppm, which is three times higher than that of the Chinese Bayan Obo deposit. Samples classified as very promising and promising because of their outlook coefficients, are found to contain up to 77% of critical REY. It is envisioned that the area could be a prime deposit for these REY.

Nov 6, 2024

By Ronald W. Schaefer

This report describes operations at the Rosiclare Fluorspar Works of the Aluminum Co. of America at Rosiclare, Hardin County, Ill. The works include the Fairview mine, the fluorspar mill, and related facilities. The publication covers exploration, development, mining and milling practices, mine-drainage problems, and other activities and is presented as part of the Bureau of Mines series of publications on mining and milling practices in various parts of the United States. The Rosiclare fluorspar area, for its size, has been the largest producer of high-grade fluorspar in the United States and probably in the world. The vein system in this area is over 5 miles long and 1/2 mile wide, and ore has been found as deep as 900 ft.

Jan 1, 1961

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By Mayara Gallego Cucchiara

Neste trabalho, blendas de ABS (acrilonitrila-butadieno-estireno) e HIPS (poliestireno de alto impacto) provenientes de carcaças de equipamentos eletro eletrônicos (EEE) foram estudadas. O material foi moído em duas granulometrias diferentes (uma fina e outra grossa). Os corpos de prova para ensaios de tração e impacto de blendas ABS/HIPS na proporção 50/50 (% em massa) foram obtidas diretamente por injeção variando-se a velocidade de dosagem (50, 150 e 300 mm/s) e a granulometria do material moído (fina e grossa). Os corpos de prova obtidos foram caracterizados quanto às suas propriedades mecânicas (resistência à tração e resistência ao impacto). As diferenças obtidas nas propriedades mecânicas foram avaliadas através da análise de variância (Anova-fator duplo com repetição). Observou-se que a velocidade de dosagem e a granulometria do material não afetaram significativamente os valores de módulo de elasticidade aparente e deformação na ruptura das blendas obtidas. Já a granulometria mais fina resultou em blendas com uma maior resistência à tração e maior resistência ao impacto, não importando o valor da velocidade de dosagem utilizada durante o processo de injeção.

Aug 8, 2018

By Leonardo Lúcio de Araújo Gouveia

Este trabalho objetiva o estudo da influência da adição de fibras vegetais de bambu e cana-de-açúcar nas propriedades mecânicas do concreto. Para este trabalho foram confeccionados corpos-de-prova cilíndricos e prismáticos nos quais foram adicionados 2% e 5% em volume das fibras à massa do concreto. Após a cura, conforme NBR 5738 (2003) [1], os mesmos foram testados via ensaios de resistência à compressão conforme NBR 5739 (2007) [2], resistência à tração por compressão diametral, conforme NBR 7222 (2011) [3], resistência à tração na flexão conforme NBR 12142 (2010) [4] e módulo de elasticidade estático, conforme NBR 8522(2008) [5]. Verificou-se após os testes que todos os concretos produzidos atenderam a resistência mínima a compressão de 20 MPa, recomendado pela NBR 6118 (2003) [6] para fins estruturais. Foi observado um aumento da resistência à compressão em relação à mistura padrão. O concreto com adição de fibras de bambu apresentou melhor resistência mecânica em relação ao concreto com adição das fibras de cana-de-açúcar e ao concreto sem adição.

Aug 7, 2018

By Fábio de Oliveira Braga

Um sistema de blindagem multicamada consiste de uma camada frontal de cerâmica, uma camada intermediária de fibras sintéticas ou de material compósito, e uma camada posterior de um metal dúctil. Recentemente, há o interesse em substituir as fibras sintéticas por fibras naturais, por suas propriedades adequadas, menor custo e peso. O objetivo deste trabalho é avaliar o desempenho de compósitos de matriz poliéster reforçados por fibras naturais de Curauá em blindagens multicamada. Placas com 0, 10, 20 e 30% vol. de fibras integraram a blindagem que sofreu impacto balístico com munição 7.62 mm, e o dano foi avaliado pela indentação característica em plastilina e por uma análise microscópica das superfícies de fratura. Foi mostrado que a blindagem resiste ao impacto balístico, atendendo à norma NIJ-0101.04 para o nível de proteção III. Além disso, as fibras de Curauá são responsáveis por manter a coesão do compósito após o impacto balístico, e o compósito por dissipar parte da energia do projétil por mecanismos como delaminação, trincamento da matriz, fratura e descolamento das fibras.

Aug 16, 2017

By Mariana Tomé da Silva

A câmara de empuxo do Motor Foguete a Propelente Líquido (MFPL) L75 é composta de uma liga Cobre cromo, classe C18200. A jaqueta de refrigeração, responsável pela extração de calor, é feita de aço inoxidável AISI 316L. No que tange ao processo de fabricação, a união entre a câmara de combustão e a jaqueta de refrigeração é uma etapa crítica, pois envolve processos de união de materiais dissimilares e de componentes de geometria complexas. Este trabalho visa contribuir à fabricação do conjunto motor foguete, por meio da soldagem a laser entre a câmara e a jaqueta. Com o uso de um laser a fibra de alta potência, foi possível verificar que existe uma condição otimizada de solda sobreposta, inox sobre Cu(Cr), com potências entre 1.000 e 1.300 W e velocidades de soldagem de 0,05 m/min a 1 m/min. Embora as análises mostrem heterogeneidade microestrutural, pela dissolução parcial de uma fase na outra, obteve-se níveis de dureza aproximadamente constantes ao longo da profundidade da junta.

Aug 16, 2017

By G. H. Wigton

THE oxidized ores of the Chief Consolidated Mining Co., in the Tintic mining district, have never yielded to metallurgical treatment by any standard method except smelting. These ores occur in comparatively small, irregular, siliceous replacements in limestone, and carry silver, lead, and gold as the principal valuable metals. But smelting methods. are unsatisfactory, as the lead smelters heavily penalize the large amount of silica in the ore, and the copper smelters do not pay for the lead in the ore; therefore, an alternative treatment method was sought. In 1916, a metallurgical research department was organized under; the direction of the writer. Many standard metallurgical methods were investigated but, on oxidized ore, none yielded extraction great enough to make its use feasible. During some chloridizing-roasting experiments in 1916, made in an assay muffle, the writer noted that large proportions of the silver, lead, and gold were volatilized from certain oxidized ores. The possibility of volatilizing the metals and collecting them in the form of a concentrated fume was then studied. But, as it was shown that satisfactory chloride-volatilization would be limited to a furnace feed with a high fusing temperature of the non-volatilizable constituents, and as the results obtained in a rotary kiln with the admixture of common salt with the ground ore were inferior to muffle tests, further volatilization experiments were discontinued until 1920. During this interval, an experimental sulfidizing and flotation plant was operated. After the cessation of attempts to float the oxidized minerals, chloride-volatilization experiments were resumed. The highly infusible flotation. tailing from the operation of the flotation mill was used for furnace feed. The first tests made on flotation tailing mixed with 10 per cent. common salt showed -nearly complete lead and gold volatilization but considerably less volatilization of silver than in muffle tests. In attempts to increase the silver extraction, the percentage salt in the furnace feed was varied, and it soon became apparent that the use of smaller percentages of salt raised the fusion temperature of the furnace charge and thus,

Jan 8, 1925