Search Documents

By Einar Carreño

El artículo evalúa 4 alternativas para el transporte de la mezcla para concreto shotcrete en una operación minera subterránea (Volcan): 1) con planta en el interior de la mina, 2) mezcla enviada por una red tuberías de acero a tubo lleno, 3) mezcla enviada a impacto por un tubo de acero vertical y 4) con un sistema mixto de transporte masivo de relleno cementado. Se evalúan con detalla ventajas y desventajas de cada alternativa y se ofrecen recomendaciones para optimizar el proceso reduciendo tiempo y costos.

Sep 20, 2019

By Elio Ferreira

This report describes the design, and development work performed to reduce the volume and weight of the miners caplamp battery, as well as a headpiece with a swivel mechanism containing a halogen bulb with two filaments. Work was also conducted in the development of a maintenance free battery. The design concept is based on non-sintered Ni-Cd technology, with an energy density of 22 Wh/lb. The cap lamp system developed has been approved by the Mine Safety and Health Administration (MSHA) and can be manufactured for mine use.

Jan 1, 1988

By Rusdian F. Kayadoe, Michael B. Hutahaean, Sandi A. Firmanulhaq

Deep Mill Level Zone (DMLZ) mine is located in Papua, Indonesia operated by PT Freeport Indonesia (PTFI) with approximately 1,500m below surface. The ore body extend 1230m width from northwest to southeast by 300–400m length east-west. The mine currently produces at full production of 80,000 tons per day until 2041. Part of the extension of current active production block and mitigation sits 225 m above the production block 1 (PB1) and 2 (PB2A and PB2B) which located in 2590L, named production block#4 (PB4W and PB4E). As the mining continues at PB1N, PB2A, and PB2B, the cave growth vertically and laterally to south perimeter of the footprint affecting the integrity of PB4W/E footprint. Currently, PB1N and PB2N are in active production whilst PB4E development continues from South against PB1N cave, as can be seen in Figure 1. A slight overlapping between PB1E and PB4E intentionally to promote cave connections between the two caves. Despite low stress model in the PB4E near existing caves, the PB4E cave propagation expected by the large strain and will be propagating in tension failure to the PB1E cave. Hence, designing the drill drives edge and first drawbell location as close as possible to the PB1E cave is necessary to guarantee cave connection. Since PB4 footprint development commenced in December 2021, there have been a substantial cave propagation observed from existing downhole monitoring. As the PB4 footprint designed perpendicular to existing DMLZ PB1 cave, adjustment of the development edge design is necessary to reflect the progression the loosening zone propagation to the South. Final life of mine design for extraction, undercut and ventilation level were decided in October 2023 considering latest update cave (fractured/ yielded) boundary. Numerical model of potential rock mass damage also aids the decision to locate the drift edge design. Predicting the cave progression impact is critical to both production at the existing active blocks and development of the new area. The use of cave shape data from year 2021–2023 gives an insight of the cave shape estimation at the end of 2024 when the undercut drift will be developed. This paper presents actual cave growth of active production blocks and its relative vertical progression impact as the result of drawing in order to plan for acceptable rate and provide mitigation once the minimum acceptable rock mass condition and minimum pillar threshold achieved.

Feb 1, 2025

By Jason M. Ryan, T Michael LeBlanc, John H. Heiiig

Drill trajectory deviation is a recurring problem in the Mining Industry retreat stoping operations. As a result of this deviation, it is quite concevable that 60 kg (165 mm 0) and 103 kg (203 mm 0) explosive charges are detonated beyond the hanging wall contact. Consequently, there follows a reduction in hanging wall stability and an increase in ore dilution.

Jan 1, 1995

By Raja V. Ramani, Sachin Shankar

"Re-entrainment refers to dislodgement of particles deposited by both atmospheric and nonatmospheric processes and their subsequent insertion into a flowing field. Formation of sand dunes, snow drifts, soil erosion and fugitive dust emissions are a few examples of the natural occurrence of re-entrainment. Re-entrainment studies have been done for the estimation of potential hazards from nuclear fallouts. The phenomenon of re-entrainment has been utilized for the cleaning of wafers and filters. Re-entrainment is associated with both surface and underground mining activities. However, studies on dust re-entrainment in mine atmospheres are limited. Understanding the re-entrainment phenomenon is important because dust particles lying seemingly harmless on the ground and adhering to numerous surfaces can get re-entrained and become a health and safety hazard.There are significant differences in the kind of re-entrainment encountered in underground mines and those in other fields of interest. These major differences are air velocity, direction of air flow, particle size, amount of particles, and time of exposure. While numerous studies have been done in other fields to identify the role of interacting variables and their contribution to the mechanisms of re-entrainment, no similar reported work is available for dust in mine atmospheres.In this paper, recent research efforts on re-entrainment are reviewed. The most suitable form of representing re-entrainment in underground coal mine atmosphere is presented. Various approaches to studying re-entrainment phenomenon in mines are also outlined.In the mineral industries, formation of dust particles of widely varying sizes is a natural outcome of the fragmentation required in mining the solid resources. Fine particles in mine atmospheres, particularly in the respirable size range, are a threat to the health and safety of the miners when present in high concentrations. In 1980 the National Academy of Sciences (NAS) Committee on the Measurement and Control of Respirable Dust in Mines recommended that the spatial and temporal characteristics (of fragments produced in coal mining) need to be understood so that the exposure of workers to the dust can be controlled. Recently several studies have been performed to understand the fundamental behavior of the airborne respirable dust in mine airways (Bhaskar, 1987; Qin, 1988; Polat, 1989; Bode, 1990)."

Mar 1, 1992

By A. U. Miller

"Ventilation is one of the meet important factors in mining, although until recent years less thought has probably been given to effective ventilation than to any other one phase of mining. In the past, very little, if any, attention was given air courses until they became so constricted by falls that the volume of air was greatly reduced; and, in addition, the stoppings and doors were so poorly constructed that only a very small percentage of air reached the face workings.As a matter of fact, mines have been visited where the volume of air being circulated in certain sections was much larger than in others, and where the management was striving to increase the flow of air in those sections with the least air current, believing the ventilation to be deficient. After sampling and analyzing the return air from the various sections in such mines it has been found that the quality of the air in certain places with the largest flow was more impure than in some of those with the least flow.In past years, practically all mine fans were operated by steam-driven engines supplied with steam from the mire boiler plant. No check was made on the steam consumption or the power cost of operating the fan, therefore the management had very little if any definite information as to cost of ventilating the mine.With the increased use of electrically-driven equipment in mines electricity is being used more and more to drive mine ventilating fans, and since in many instances the current is purchased from central power plants operators have come to realize that in many cases the cost of operating the fans is very high. Some engineers estimate that it ranges from 20 to 50 per cent of the total power cost of the mine. This information, together with the fact that mines are now being developed on a larger scale, requiring larger quantities of air for the men to dilute the gases liberated, has caused the large progressive companies to make, a more comprehensive study of mine ventilation, resulting in a decided improvement in the quality and quantity of air at the face workings, as well as reducing materially the ventilating costs."

Oct 1, 1930

By D. E. Sherwood

Mr. Tamaro introduced his paper which concerned the construction of foundations for the buildings and related infrastructure of the World Financial Center on a reclaimed shoreline site at the Southern tip of Manhattan Island. This large project presented difficult design and construction problems, both geotechnical and structural. All structures were supported by foundations carried to rock. Two of the buildings were supported by conventional pier (pad) foundations constructed within diaphragm wall cofferdams. The remaining structures were supported by either piles to rock or caisson (large diameter) piles with socket depths drilled through the rock of up to 7.6 metres. Underground services, railway and proposed road tunnels all affected the installation of foundations. The proposed road tunnels for the new six lane 'Westway' would involve an excavation 12 metres deep adjacent to and under three buildings. This problem was solved by an agreement that tower windloads would be taken by the tower foundations and not distributed through the basement walls. This was achieved by a system of battered caissons founded on the rock and arranged so that adjacent caissons were founded in different rock masses. Diaphragm walls were restrained using tie backs. Ground testing indicated an exposure to D.C. stray current corrosion of all underground construction. As a result all of the foundations were isolated from the ground by non-conductive materials. In the case of piles and caissons the reinforcing for the caisson was fully protected by concrete and all outside steel used for the installation of piling was considered sacrificial and not used in the computation of long term load carrying capacity.

Jan 1, 1991

By Taehong Kim

An accurate and reliable prediction of Tunnel Boring Machine (TBM) performances, in terms of Rate of Penetration (ROP), utilization (U), and cutter wear rate, is a critical element in the successful planning and execution of mechanical tunneling project. Three open hard rock TBM projects were studied to establish possible trends and correlations between rock mass properties and machine performance. Based on this analysis and literature survey, three geological parameters, including RQD, RMR, and groundwater inflow rate, were identified as having the greatest impact on TBM utilization level. Rate of Penetration (ROP) and cutter wear rate were also correlated with fracture spacing, alpha angle, and Cerchar Abrasivity Index (CAI).

Jan 1, 2008

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By Laura McNally

In 2006, McNally International Inc., in a joint venture partner-ship with Aecon Constructors, was the successful bidder on two York Region Tunnel Projects: the Bathurst Collector/Langstaff Trunk Sewers and the York Durham Sewer System (YDSS) Interceptor Sewer 19th Avenue, both in the Toronto area. These projects comprised a total of 13 km (8 miles) of 2.74 m (9 ft) finished diameter tunnels and are both part of the YDSS. Both contracts required the use of earth pressure balance (EPB) tunnel boring machines (TBM) with a precast concrete segmental liner.

Jan 1, 2008

Recent data contributions to New Zealand Mesozoic terrane geology confirm the consensus interpretation thatNew Zealand grew by the progressive addition of material by plutonic and accretionary processes along the Gondwana margin. The data also: 1. emphasise the discontinuous but inter-related nature of these processes of continental growth, 2. better establish a direct Gondwana correlation of the Western Province and probable Gondwana provenance of at least some of the Eastern Province, 3. suggest specific times and places when passive or strike-slip rather than subduction regimes are recorded along the south Gondwana margin, and 4. potentially lead to interpretations emphasising parautochthonous rather than far travelled relationships between many New Zealand terranes.  

Jan 1, 1995

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By Jonatas Venâncio Barbosa

Descrevem-se as ações adotadas para a evolução da qualidade de aços ultra baixo carbono com alto teor de silício, destinados a aplicações eletrônicas. Com o propósito de conhecer o comportamento metalúrgico do material durante o processo de laminação foram realizados ensaios de dilatometria, que permitiram a determinação das temperaturas de transformação de fase. Foi evidenciado que, nas temperaturas de processo praticadas, a laminação no trem acabador ocorria na região intercrítica, gerando variações bruscas de propriedades mecânicas no processo, levando a instabilidade operacional. Esta condição de laminação foi corrigida, direcionando para laminação em fase ferrítica. Foram necessários ajustes no modo de operação na linha de tiras a quente e a criação de controle automático de temperatura na entrada do trem acabador. Após as ações foi possível melhorar a qualidade do produto final, em relação às dimensões e forma do produto, reduzindo as perdas internas e retrabalho.

Aug 16, 2017

By A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. NIOSH has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by 9 decibels. The ?Inquiring Ears Want to Know? fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By Aquiles Vivar Montañez

"La construcción de losas de relleno cementado en la aplicación del método de corte y relleno descendente, es una etapa importante en el ciclo de minado - en tanto representa uno de los mayores costos de extracción por tonelada de mineral. En este contexto, es necesario establecer metodologías adecuadas para el diseño de losas basadas en técnicas empíricas y analíticas, así como para el de recuperación de pilares. Por ello, el presente texto señala la optimización de la resistencia del relleno cementado a través de la reducción del ancho de minado en los sectores de mayor potencia y la reducción del módulo de rigidez de la losa para que guarde equivalencia con la rigidez de las rocas encajonantes, que son de baja calidad geotécnica. "

Sep 1, 2015

By Breno Totti Maia

O BOF, Basic Oxygen Furnace, ou convertedor LD, é o processo mais utilizado industrialmente para o refino primário do ferro gusa atualmente. Para aumentar a produtividade do BOF deve-se diminuir o tempo de cada ciclo de operação, especialmente o tempo de sopro aumentado a taxa de descarburação. Durante o sopro do convertedor existem três etapas. A segunda etapa do sopro a taxa de descarburação é alta e constante sendo o fator limitante é a disponibilidade do oxigênio no banho e determina o tempo de sopro. Assim para aumentar a descarburação pode-se melhorar a interação do jato de oxigênio com o banho, configurando o convertedor. Estudando o sopro combinado em um modelo fisíco de um convertedor LD de 220t, foi testado diferentes bicos de lança com um sopro de 160Nm3/h de vazão e vazões de 4Nm3/h e 6Nm3/h nas ventaneiras. Através dos testes pode-se observar que aumentando o número de furos no bico o jato teve menor penetração, maior área de agitação e as projeções tiveram menor altitude, já a injeção pelas ventaneiras aumentou a penetração do jato e diminuiu as projeções. Foi calculado também valores para a constante K para cada configuração, assim é possível prever a penetração do jato industrialmente.

Aug 17, 2017

By Dwayne C. Kicker

This paper introduces the concept of design theory and methodology as applied to rock mechanics for more innovative and efficient design. This is a "frontier" research area in rock mechanics because although design is a fundamental foundation to all engineering branches, very little attention has been paid to this aspect in mining. In discussing the theoretical premise of design, this paper identifies the principles which form the basis of design activity. Also, from a practical viewpoint, the findings from a series of interviews with mine design engineers are presented. These findings lead to the identification of needs arising from overlooked design methodology in practice.

Jan 1, 1989

Thermodynamics of Non-Cyanide Gold Solvents The present status of the raw material base in the gold industry requires specific ways to recover gold and silver from ores. Most gold is closely associated with sulfides which require flotation followed by pressure or bacterial oxidation. The next stages of processing usually require using expensive operations for the preparation of leaching. A lot of researchers want to find a new alternative solvent for the extraction of precious metals from these products. According to the authors, one of the best ways is to use sulfur-based solvents (thiosulfate, sulfite, and their various mixtures). Thermodynamics of gold and silver thiosulfate dilution are calculated for conditions: the concentration of Au - 200 mg/L, oxygen - 3.2 mg/L, thiosulfate - 79 mg/L, OH- - 170 mg/L. the general result is the possibility of process remains under standard conditions. (erAu = = 0.035 V, ?G298 = - 29.18 kJ/g-atom ??). Silver with thiosulfate forms two strong complexes: [AgS203]- and [Ag(S203)2]3-. ?G0 = -1027 kJ/mol. The complex [AgS203]- is less stable: ?G0 = 486 kJ/mol. It should be noted that despite the high stability of gold complexes, the sodium thiosulfate may decompose to sulfite and elemental sulfur during the process, especially when heating. Gold is slightly soluble in the sodium sulfite solution, however it forms the strong complex [Au(SO3)2]3-. Depending on the concentration of free S2O32-ions, silver with sodium sulfite forms three complexes: [AgSO3]-, [Ag(SO3)2]3- and [Ag(SO3)3]5-. The dissolution speed of gold in sodium sulfite solution may be in the same range as it is during cyanidation. In this case, a practical application of sulfite process can be also used, especially for the products containing free elemental sulfur. In conclusion, sulfite-thiosulfate gold lixiviants can be used for concentrates after pressure oxidation of the cakes.

Sep 13, 2010

By C. E. T. White

Although trace amounts of Indium are found in many ores, commercial production of the metal has come almost exclusively from residues, flue dusts and slags generated by Zinc recovery operations. Our paper attempts to summarize the various approaches used to recover Indium from these by-products. Some comments on production and price trends are included as well as our views on future availability.

Jan 1, 1982

By W. Duyvesteyn, B. Sabacky, T. Spitler, D. Verhulst

"The Altair TiO2 pigment process is based on hydrochloric acid leaching of ilmenite at high-acid concentration. Titanium is transferred by solvent extraction into a high-purity aqueous stream with a high titanium concentration. HCl gas is recovered by pressure-swing distillation and is used to regenerate the leaching solution.A new method of TiO2 recovery in dense film with simultaneous dehydration and hydrolysis provides great flexibility in adjusting the characteristics of the TiO2 pigment product.Modifications of this method lead to a flexible, low-cost, high-tonnage process first for the production of nano-sized TiO2, and later for stabilized zirconia-based nanomaterials and nano-sized titanates.IntroductionProcesses for the production of TiO2 from ore by a hydrochloric acid route have been proposed in the past. Most of these processes dissolve impurities and recover TiO2 as a residue or as a hydrolyzed phase in the original solution (Turner, 1948; Berkovich, 1975; Morris, 1982; Judd, 1986; Chao, 1993). Solvent extraction of titanium after leaching in aqueous HCl has also been studied (Tsuchida et al., 1982; Narita et al., 1983) or at least mentioned as an alternative (Ellis, 1963). A number of small-scale studies on leaching and solvent extraction in both sulphuric and hydrochloric systems have appeared recently (John et al., 1999; Lanyon et al., 1999; Sole et al., 1999. As far as we know, only Kerr-McGee (Morris, 1982) and a plant in India and one in Malaysia use a hydrochloric acid route (20 wt% HCl) to commercially produce synthetic rutile.The Altair process originated in a search for an economical method to treat high-magnesium ilmenite deposits, while avoiding the production of a waste metal salt by-product. The first attempts aimed at producing pure TiO2 by leaching out the impurities. Further work centred on completely dissolving the ilmenite in concentrated hydrochloric acid and reprecipitating TiO2. To decrease the impurity level in the product, solvent extraction of titanium into a purified stream was introduced. It also became clear that to take full advantage of the increase in leaching efficiency provided by concentrated acid, it was necessary to regenerate HCl gas."

Jan 1, 2002