Search Documents

By W. H. McCormick, H. J. Benecki

CONSIDERING that a typical modern drilling machine strikes approximately 2000 blows per min and may develop a force of 30 to 200 ft-lb, de- pending upon size of the drill used, the importance of uniform stress distribution in this type of drilling becomes obvious. If the rod were perfectly symmetrical, and if it did not rotate, the problem would be relatively simple, however, the necessary forging, machining and heat treating operations prevent attaining this state of perfection. Take the modern hollow drill rod. The blow is transmitted not from the striking end of the rod directly through to the point of impact of the bit in the rock, but rather through a somewhat complex tool. To add further problems, this entire assembly is rotated immediately after the impacting blow. Rather than attempt to discuss the magnitude and distribution of stresses, it is desired to present a few things that will minimize unusual stress concentration and produce a rod in which the stress distribution will approach the theoretical ideal.

Jan 3, 1954

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By Lucas Travi

Os problemas gerados no processamento do aço inoxidável AISI 316 são um grande problema do setor metal mecânico, por exemplo, no processo de usinagem, onde o material sofre altas taxas de deformação plástica e elevadas temperaturas na região de contato ferramenta-peça. Além disso, a adesão de aço inoxidável em materiais de maior dureza, no caso a ferramenta, também são problemas enfrentados. Neste trabalho foi feito um estudo qualitativo em escala laboratorial do contato entre um material de maior dureza (aço AISI M2 nitretado a plasma) e o aço AISI 316. Foram realizados ensaios de microdureza Vickers e rugosidade afim de caracterizar as amostras de aço AISI M2. Ensaios tribológicos do tipo Ball-on-Plate foram realizados com a finalidade de determinar o coeficiente de atrito ao longo do tempo para os pares tribológicos formados. Análises feitas via MEV/EDS foram feitas tanto nas trilhas geradas nas superfícies das amostras quanto nas esferas, para detectar pontos de adesão, deformação plástica e transferência de material entre as duas superfícies. Ficou comprovado que a nitretação a plasma com gaiola catódica proporcionou um menor coeficiente de atrito ao longo do tempo quando posta em contato com a esfera de aço inoxidável, bem como foi possível observar a formação de uma menor quantidade de pontos de adesão de aço inoxidável para esta superfície.

Aug 17, 2017

By Carolina Machado de Castro Amaral

A necessidade de treinamento é uma realidade nas indústrias. A qualificação de operadores é importante para garantir segurança e prevenir perdas econômicas. Nesse contexto, o objetivo desse trabalho é desenvolver e avaliar um simulador de treinamento de operador. O estudo de caso é um moinho vertical, comumente utilizado na indústria de cimento. Nessa direção, passou-se pela construção de um supervisório, pela modelagem e simulação dinâmica de um moinho vertical e, por fim, pela elaboração e execução de um treinamento. Para tal, foram construídos três cenários de situações anormais, além da consideração da operação normal. Ainda em relação à metodologia, treinaram-se dois grupos de alunos com métodos distintos de ensino: o primeiro recebeu apenas um treinamento teórico, através de uma apresentação multimídia; e o segundo, após esse treinamento teórico, recebeu um treinamento prático, ou seja, do tipo aprender fazendo, a partir do contato direto com o simulador de processos. De modo geral, percebeu-se que o contato com a prática possibilitou um maior entendimento da operação do moinho vertical, do grau de dependência entre as variáveis de entrada e de saída, e das variáveis utilizadas para a recuperação do processo à operação normal, contribuindo ainda para uma maior fixação do conhecimento teórico. Esse trabalho é resultado de uma parceria UniversidadeEmpresa, cujas atividades foram desenvolvidas por um grupo de alunos de graduação em Engenharia Química.

Aug 17, 2017

By Patrick M. - Langevin

THIS TALK IS ABOUT : How the DBL mining camp deposits have been found and what is done to find the next one PLAN: Overview of the geological context Historical exploration perspective Deposits geology and key features Conclusion

May 1, 2006

By A B. Christie, S C. Cox

Effective land-use planning requires accurate knowledge of mineral resource potential. Mineral companies during reconnaissance exploration, feasibility investigations and mine development also use this type of analysis. The Institute of Geological and Nuclear Sciences is undertaking a two-year project reviewing the resource potential of the West Coast of the South Island of New Zealand. Spatial prospectivity models have been developed as part of this resource assessment process, using computer based statistical pattern recognition techniques to delineate areas that are prospective for mineral deposits and to test deposit genesis models. Digital GIS data-sets of mineral occurrence were correlated against geology and exploration information. The distribution of mesotherrnal shear zone gold deposits in the Reefton Goldfield, were examined against geological data-sets from both the regional (QMAP) and local prospect-scale mapping. Weights of evidence analysis generated a correlation matrix that highlights relationships and degrees of association that might otherwise not normally be recognised.   Mesothermal shear zone gold deposits have strong positive spatial correlations with Greenland Group host rocks and areas with moderate to high quartz vein densities; moderate-strong positive correlation with regions <500 m from folds, with regions <600 m from faults and five to eight kilometres from granite contacts; moderate correlations with Ntrending fault and fold segments; and no/weak/poor correlations with fault intersections, fold-fault intersections, bends in regional structures and magnetic and radiometric data. The regional and prospect scale data sets give different results, with the more detailed prospect scale mapping giving generally better correlations. This emphasises the value of detailed geological mapping in the exploration process.   Maps generated by prospectivity modelling consistently highlighted areas of known mineralisation and generate targets where follow-up investigation is warranted. The prospectivity per unit area provides a measurable value that should change as new information comes to hand and, in addition to highlighting targets, can be used to measure the impact of increased exploration expenditure and assess the effectiveness of exploration investment.

Jan 1, 2001

By Rayner B

Five wells have been drilled in the Basker/Manta Block of VIC/P19, Gippsland Basin, resulting in sub-economic Intra-Latrobe Group oil and gas discoveries at Basker-1 and Manta-1. A total of 21 individual hydrocarbon bearing sandstones were intersected by the two wells. These reservoir sand bodies were deposited by fluvial processes in a lower coastal plain environment. The modelling of sand body orientation and geometry is a critical component in the evaluation of the two accumulations. Seismic resolution of the thin (average 2 m to 5 m) sand bodies is inadequate for mapping their orientation and distribution. Dipmeter data has been successfully applied to the problem of orienting the sand bodies using FMS images acquired during the drilling of Gummy-1 and reprocessed HDT data from Basker-1 and Manta-1. Prediction of lateral extensiveness (geometry) of individual sand bodies has also been attempted. Interpreted palaeocurrent direction from all three wells is dominantly from the NW to the SE. Reservoirs in the Manta-1/Gummy-1 area are interpreted to be predominantly channel sands, deposited by relatively low sinuosity streams. As such they would tend to have a laterally extensive, elongate geometry. Sand bodies deposited in the Basker-1 area show a predominance of laterally accreted cycles deposited by meandering streams. Channel geometry may then be limited in the downstream/upstream direction by internal permeability barriers such as clay plugs.

Jan 1, 1992

By R J. Butcher

Many deposits have been evaluated as potential block caves over the last 20 years due to the perceived benefit of low operating costs. However, block cave projects are typically capital intensive, with mass mining providing high throughput rates that required large investments in mining, processing and utilities infrastructure. While the key economic metrics in deciding to proceed with a caving project are typically net present value (NPV) or internal rate of return, these may not represent the best decision metrics for some companies. Where a caving project is competing for scarce capital amongst other projects in a company’s portfolio or where the caving project is the only project being evaluated by a company trying to raise capital, other metrics may be more appropriate. This paper explores the use of present value ratio and the minimising of maximum negative cash flow as suitable metrics in determining alternative strategies. Trade-offs between optimising for economic value and capital efficiency measures allow for decision-makers to evaluate potentially higher-risk, higher-capital and maximum NPV projects against lower-risk, lower-capital projects.CITATION:Stewart, C A and Butcher, R J, 2016. Block cave evaluation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 809–816 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. M. Whatley

"IntroductionIN UNDERGROUND mining operations, the mine hoist has become one of the most important and one of the most expensive single pieces of equipment. As the means of transporting men and materials to the face, broken ore to the mill, and waste to the dump, it is often the very lifeline of a mine and must operate with dependability and efficiency or the whole operation will suffer. The mine hoist has become synonymous with safety. In few other types of mechanical equipment do so many men so frequently and completely place their lives. In Canada, more has probably been done to assure safe hoisting than in most other countries, but, unfortunately, this has resulted, in many cases, in the mines having to pay a high price for equipment. Hoist manufacturers have carried out much research in recent years in the endeavour to keep down these costs and at the same time maintain or improve the efficiency and safety of their products. Broadly classified, the bases for design research are dependability, efficiency, safety, and first cost.Probably the greatest single factor influencing the design of mine hoists was the introduction of electric motor drives. It was not until about 1905 that an effective start was made in the development of electric mine hoists, and then only with machines of small size. From that time on, however, progress was rapid, as may be gauged from the fact that by 1910 one large group of mines in Johannesburg had in use, or on order, fifty-four three-phase hoists and four Ward-Leonard. type hoists."

Jan 1, 1953

By Leland E. Paulson

This investigation examined the feasibility of altering the inorganic component of North Dakota lignite by ion exchange. Lignite of specific size consist was washed with various ionic solutions and examined for evidence of exchange. Ions of higher valance substituted preferentially at equivalent concentrations. Results indicate that a major portion of the inorganic material associated with lignite is combined in exchangeable form with the organic component. Particle size of the treated coal is a critical factor in determining the rate of exchange. The data indicate that monovalent ions are easily replaced by divalent and trivalent ions, and the presence of ionic material in slurries containing finely divided lignite significantly increases filtration rates.

Jan 1, 1968

By Harold N. Miller

Lost time and services caused by electrical equipment breakdown or cable faults can often be substantially reduced by the use of direct-current high-voltage testing as a maintenance tool. This paper discusses the relative merits of alternating-current versus direct-current testing, pointing out the advantages in size and cost of equipment and more definitive results achieved through the use of D.C. General principles of direct-current high-volt-age testing, types of testing, methods of performing the actual test and interpreting the results are explained. ?The value of insulation resistance measurements and their relationship to high-voltage testing is discussed. Pinpointing the physical location of a cable defect using a fault locator or thumper is described. Reference is made to several organizations that have effected considerable savings with high-voltage test programs. Introduction T HE past decades have seen great advances in the field of electrical power distribution and application. Motor generators, power-operated equipment, cables, etc., have all gone through various stages of improvement both in efficiency and reliability. Un-fortunately, however, power failures and equipment breakdown still occur -frequently with disastrous effects in loss of time,

Jan 1, 1965

By Sérgio Wilibaldo Garcia Scherer

O Balanço Energético Nacional do MME informa que em 31/12/2012, o carvão mineral representa 73% dos recursos e reservas nacionais de energia fóssil. A partir de 1960 foram realizados estudos e experiências que resultaram na implantação da Aços Finos Piratini (AFP), uma mini usina integrada para aços especiais pela rota tecnológica “Redução Direta a redutor sólido / Aciaria Elétrica”, na cidade de Charqueadas/RS. A unidade Sl/RN (forno rotativo) operou de 1973 a 1990, com carvão local com até 35% de cinza. O processo atraiu a atenção mundial: em 1974 foi feito um teste industrial bem sucedido com linhito briquetado alemão; em 1975 o ILAFA realizou em Porto Alegre seu Seminário Internacional sobre Redução Direta; equipes da África do Sul e da Índia foram treinadas na AFP. A Índia é atualmente a líder mundial na produção de ferro esponja a carvão. O trabalho apresenta um modelo de usina integrada, autosuficiente em redutor e energia elétrica, à base de carvão não coqueificável, produzindo tarugos. Além disso, apresenta outras possibilidades de emprego do carvão mineral nacional em siderurgia, tais como a injeção de finos nos altos fornos e seu emprego no processo COREX. As perspectivas futuras estão delineadas em documento do Centro de Gestão e Estudos Estratégicos (CGEE) do MDIC, que coloca metas para 2022 e 2035.

Aug 1, 2018

By H G. Poulos

"This paper sets out a simplified approach by which the practical foundation designer can undertake the relevant calculations to satisfy the requirements for deep foundation design in seismic areas. The following matters are dealt with:a. Design issues that should be addressed;b. Pile design for axial loading, including the possible effects of liquefaction;c. Pile design for lateral loading where liquefaction does not occur;d. Pile design for lateral loading where liquefaction does occur;e. Measures to mitigate against liquefaction effects.The paper is a modified version of a paper presented in 2013 to the 19th NZGS GeotechnicalSymposium, Queenstown, New Zealand.1. INTRODUCTIONConsideration of the effects of earthquakes and seismic loadings is an increasingly important aspect of modern foundation design, and most contemporary standards have a mandatory requirement for such consideration. For example, the Australian Piling Code, AS 2159-2009, states that “a pile shall be designed for adequate strength, stiffness and ductility under load combinations including earthquake design actions”. However, the methods by which such considerations can be undertaken are generally not set out in the standards, and many approaches have been utilized, ranging from very simplistic methods to extremely complex computer analyses. Accordingly, there appears to be scope for an approach that is soundly based but which is neither too simplistic nor too complex.Poulos (1989) has suggested that there are three categories of analysis and design, as follows:1. Category 1: empirical methods.2. Category 2: simplified but soundly-based methods.3. Category 3: more comprehensive methods that are soundly-based, and site-specific.The objective of this paper is to set out a systematic but simplified approach which falls into Category 2 above, and by which the foundation designer can undertake the relevant analyses to satisfy the foundation design requirements for seismic regions. Emphasis is placed on methods that do not require “black box” software or which employ complex soil models in which the physical meaning of the parameters is unclear."

Jan 1, 1900

The Ngakuru zeolites are located about 20 km south of Rotorua and comprise a number of deposits dispersed along several fault lines. Relatively recent volcanic activity (250,000 years ago) resulted in ash depositions that vary in depth and mineralogy. Subsequent variable thermal alteration intensities generated predominantly clinoptilolite and mordenite zeolites with a range of physical characteristics. Typically the zeolites have low density (650 kg/m3), have high liquid (60% of dry weight) and odour absorption characteristics, and a high affinity for soluble cations (CEC =: 100 meq/100 g). Traditional kitty litter and oil absorbency markets are being expanded. New opportunities in waste and potable water treatment, organic and synthetic slow release fertilisers, use as a light weight aggregate for speciality concretes, and pozzalome activity are currently being researched.

Jan 1, 2000

By Xinhua Wang, Xuefeng Liu, Die Yang, Lifeng Zhang, Wen Yang

"CSP thin slab continuous casters are well used in recent years. The control of heat transfer in the mold is very important because it is correlated with several slab defects. The mean heat flux of CSP mold was studied based on the plant production data of LCAK steel and weathering steel. The effect of various operation conditions on the heat flux was analyzed and discussed. The results showed that the heat flux was 2.1-2.6 MW/m2 on the wide face and 1.2-2.2 MW/m2 on the narrow face for the casting of LCAK steels. During the casting of weathering steel, the heat flus was mostly 2.05-2.5 MW/m2 on the wide face and was 1.1-1.8 MW/m2 on the narrow face. The heat flux depended largely on the casting speed. The heat flux on the wide face increased obviously with increasing casting speed when the casting speed was relatively low; however, at high speed, the heat flux increased slowly or kept constant. At low casting speed, the heat flux depended little on the superheat of the molten steel. The mean heat flux depended little on the level fluctuation at continuous casting mold.IntroductionCSP thin slab continuous casters are used more frequently in recent years for its low cost of construction and manufacturing. The structure of CSP mold is very different from that of conventional thick slab casting mold, inducing the difference of heat flux between them. There have been some studies about the heat flux of thick and medium slab casters [l, 2]. Heat transfer in the mold is very important for the solidification of molten steel because it is correlated with several slab defects such as slab break-out, longitudinal crack, and surface depression. Moreover, higher casting speed is desired to improve the productivity. The control of solidified shell is extremely important. The heat flux is largely influenced by several casting parameters such as the cooling intensity of the mold, the casting speed[3], the mold flux powder [3, 4] and the carbon content of steel as well [5]. The investigation on the heat flux and affecting parameters can help to understand the solidification of molten steel in the mold."

Jan 1, 2013

A study of the swelling behaviour of a single batch of high-grade iron ore pellets during hydrogen reduction in a fixed bed showed that the extent of swelling is governed by the nucleation and growth of crystalline iron protuberances from the wüstite grains. Over the reduction temperature range 650 to 1000°C, it was found that substantial degrees of swelling can occur at temperatures in excess of 850°C, and significant variations in the swelling behaviour of individual pellets from different bed levels are observed under these conditions.The results are discussed in terms of a recent swelling theory and shown to be in general agreement.

Jan 1, 1978

By S. J. Lötter, J. T. Nel, W. Purcell

"SynopsisGlow discharge optical emission spectroscopy (GD-OES) is an analytical technique used in the analysis of solid, conducting materials. Though primarily of interest as a depth profiling technique on samples with varying layers of both conducting and non-conducting materials, it is also capable of rapid bulk analysis of homogenous, solid samples. GD-OES combines the advantages of ICP-OES (wide detection range, speed, and lack of interferences) with the solid sampling of XRF techniques. This allows the analyst to not only quantify the elemental composition of a sample, but to evaluate it in terms of homogeneity with depth, a field in which auger electron spectroscopy (AES) and secondary ion mass spectrometry (SIMS) have traditionally been the primary techniques. Although GD-OES does not replace these useful techniques, it does offer various advantages over them, making it an excellent complementary analytical tool.In GD-OES analysis, a low-pressure glow discharge plasma is generated with the sample material acting as a cathode, accelerating the cations in the plasma towards the sample surface. This bombardment causes the sample material to ‘sputter’, essentially knocking free atoms or molecules of analyte material, which are then drawn into the plasma where they are excited. The light emitted by this excitation is then diffracted to separate the wavelengths emitted by the specific elements and detected by a spectrophotometer. The intensity of the signal is directly proportional to the quantity of analyte element present in the sample, allowing simple calibration and quantitative determination of the elements. Technological improvements made in the past twenty years or so have significantly increased the usefulness of GD-OES for surface analysis. Faster plasma stabilization and start-up allow for the quantification of surface layers as thin as 1 nm. Sputter rates have been accurately measured for many common materials, allowing them to be built into software libraries in the instrument’s control software. This dramatically expands the usefulness of this software and the ease of performing analyses.GD-OES analysis of nuclear materials allows for the rapid determination of the elemental composition without the requirement of initial dissolution. The thickness of any corrosion layers on nuclear materials can also be determined."

Jan 1, 2015

By D J. Williams

The majority of surface tailings storage facilities continue to employ sub-aerial tailings slurry deposition. Surface TSFs are typically sized and operated in a way to minimise the initial capital cost of the facility, driven largely by the net present value approach to accounting. This generally leads to too small a storage, too fast a rate of rise of the tailings, and difficulties in managing supernatant water. In turn, this results in wet and soft tailings deposits of high moisture content and low density, and the need for frequent and costly tailings dam raises. Further, such tailings deposits often do not facilitate closure and rehabilitation of the facility. Globally, there are on average over two failures annually of such tailings dams, resulting in loss of life, damage to infrastructure and environmental impact downstream, and the loss of company shareholder value and reputation. Recent high profile tailings dam failures are threatening the mining industry’s financial and social licence to operate.Among the physical processes that tailings undergo on sub-aerial deposition are beaching, hydraulic sorting down the beach according to particle size and specific gravity, settling, consolidation, and desiccation on exposure to the sun and wind. Beaching and hydraulic sorting have proved difficult to test at laboratory scale and difficult to model, and are best assessed in the field. Settling, consolidation and desiccation may be assessed at laboratory scale, but to date there has been an absence of tests to form the basis for the design and management of tailings deposition, and ultimate closure and rehabilitation. The paper describes recent advances in tailings testing methods, including a purpose-built slurry consolidometer that tests the settling and consolidation of tailings from a slurry consistency, simulating increasing tailings depth to about 50 m; and a purpose-built instrumented column that tests the settling, self-weight consolidation and desiccation of a surface layer of tailings, also from a slurry consistency. Selected test results from these two apparatus are presented in the paper, together with brief descriptions of how they may be used to better design tailings slurry deposition. In addition, planned further advances in tailings testing methods are briefly described.CITATION:Williams, D J, 2018. Recent advances in tailings testing methods, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 8–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018