Search Documents

By I. R. Hanby

A simple solution to the problem of whether to round the calculated number of trucks up or down to the nearest whole number is to adopt as criterion the minimum cost per unit volume/mass moved, assuming all trucks in the fleet are of the same type. When the effects on journey time of varying haul-road slope are calculated for several rolling resistances, it is shown that the optimum angle of 7.5 degrees is moderately independent of both rolling resistance and height climbed; the lower the resistance, the lower the sensitivity to ramp angle, but if haul-road gradients do not exceed 1 in 10 (5.7 degrees) for safety reasons then travelling time will never be more than 7% greater than its theoretical minimum. Further calculations result in a graph of the maximum payload values to incur the minimum cost, for different values of total effective resistance

Jan 1, 1991

By Vasilis Androulakis, Caroline Gerwig, Zach Agioutantis

Mining operations that involve caving of the overlying strata are designed so that caving occurs in a controlled manner by progressive overburden failure. However, there are many cases where the overlying strata bridge over the caved area for longer periods than anticipated and desired. As the caved area expands with the advance of the mining panel, excessive amounts of energy accumulate in the roof strata which will be rapidly released when the overburden eventually fails.

This investigation was planned to determine:1. The precipitation-hardening properties of the copper-nickel-phosphorus alloys; and2. The influence of arsenic and bismuth, singly and together, on the mechanical properties of these alloys.It was carried out in conjunction with an investigation, previously published in these Prooeedings on "The Influence of Various Elements on the Mechanical Properties of Copper containing a small percentage of Bismuth," and also formed part of a study of the influence of bismuth, nickel and phosphorus on the properties of commercial arsenical-copper.The first part of the present investigation arose out of a discovery some years ago of precipitation-hardening in phosphorus-deoxidized coppernickel boiler tubes, containing approximately 2% nickel and 0·03% phosphorus, supplied to an Australian Railways Department. At that time there was little information available on precipitation-hardening in copperrich copper-nickel-phosphorus alloys, but at the end of 1935 a short paper on the subject was published by E. C. Rollason and T. G. Bamford(2) and at the beginning of 1940 a comprehensive account was published by D. K. Crampton, H. L. Burghoff and J. T. Stacy.(3) Although the investigation carried, out independently by the present author was not as comprehensive as that of Crampton, Burghoff and Stacy, the results are in agreement with those of the American as well as of the British authors; hence, only a summary of this aspect of the work is needed here to establish a basis for a study of the influence of bismuth and arsenic.PREPARATION OF TEST PIECESAll alloys were melted under charcoal in plumbago crucibles in an oil-fired furnace and were poured out of contact with air into oil-dressed moulds to give billets either 7· 5 in. long X 0.83 in. diam. X 1·3 lb. weight or 12 in. long X 1·125 in. diam. X 3·3 lb. weight depending on requirements (the larger size was used, for example, in establishing the annealing characteristics of the precipitation-hardening alloys). The raw materials were electrolytic copper of the composition described in the previous paper(I) 6% copper-arsenic, 14% copper-phosphorus, 1:7% copper-bismuth, and Mond nickel in the form of "shot." The method of producing test pieces from these billets and the annealing treatments ana tests to which the pieces were subjected have been described in the previous paper.

Jan 1, 1944

By Zirlene Alves da Silva Santos

O desgaste abrasivo é o principal responsável por quebras de equipamentos e, como consequência, paradas não programadas para manutenção; pois causa a perda progressiva de material das partes móveis em contato e movimento relativo. O presente estudo analisa o desgaste abrasivo na superfície do rolete de carga dos transportadores de correia. Para a análise foi utilizado o equipamento abrasômetro do tipo roda de borracha conforme norma ASTM G65. Os procedimentos de ensaio contemplaram: o corte de quatro corpos de prova de aço 1020, limpeza, pesagem - utilizando balança de precisão, avaliação superficial com rugosímetro e ensaio de dureza. Dois corpos de prova foram revestidos com a tinta Laranja Munsell 2,5YR6/14m, para simular as condições de campo. Em seguida, foi realizado ensaio no abrasômetro ASTM G65; utilizando o procedimento “A” previsto na norma ASTM G65 - classificado como desgaste severo com carga de 130N. Logo depois, foi calculado o volume de material perdido e a taxa de desgaste. Os resultados obtidos nos ensaios possibilitaram concluir que, o desgaste predominante na superfície dos roletes de carga é o abrasivo por 3 corpos, em função, principalmente, do transbordo de minério do processo. A superfície do corpo de prova, sem revestimento, apresentou uma perda de material que compromete a vida útil do rolete e da correia. Já, na amostra revestida, foi possível observar que o desgaste abrasivo por três corpos ocorre, mas é reduzido consideravelmente; isso pode ser explicado pela diminuição da rugosidade superficial.

Oct 30, 2017

By Luiz Flávio Pereira Costa

O quartzo contido no concentrado, medido pelo teor de SiO2, é um dos principais itens de controle de qualidade do concentrado produzido em usinas de beneficiamento de minério de ferro. Nas usinas de beneficiamento da Samarco Mineração S/A o processo de concentração é realizado em etapas de flotação reversa de quartzo. São utilizadas tanto células mecânicas quanto colunas de flotação. A especificação do concentrado final produzido na usina de beneficiamento é obtido em uma etapa de flotação em colunas (3 colunas; 3,6mX14m). Com o objetivo de melhorar a performance desta etapa de flotação em colunas foram identificadas algumas oportunidades de melhoria, a saber: substituição dos spargers por slan jet; redistribuição e reposicionamento dos borbulhadores; substituição de chapéu chinês e do distribuidor de polpa equalizando a alimentação das colunas; otimização dos parâmetros de processo (vazão de ar e camada de espuma); realização de testes de flotação em bancada com amostras do fluxo que alimenta as colunas variando a dosagem de coletor. Nos testes em bancada uma éter-amina foi utilizada como coletor de quartzo. Os testes de bancada mostraram a possibilidade de reduzir o teor de SiO2 no concentrado de forma significativa aumentando a dosagem de coletor até 75g/t. A partir das modificações no sistema de aeração, distribuição da alimentação das colunas e com a adição de coletor, a taxa de redução de SiO2 passou de 20% para 40%.

Aug 16, 2017

By P. Bakke

Following extensive R&D efforts, Hydro Magnesium has launched a new alloy series with remarkable combinations of properties. The AE alloy family is based on additions of aluminium and rare earth elements to control mechanical properties, including elevated temperature creep strength. By combining these alloying elements with manganese additions, high purity alloys with outstanding corrosion performance are defined. A basic philosophy behind the developments has been to simultaneously approach all the critical issues related to developing a commercial material. Apart from the obvious requirements for material properties, the critical issues relate to die casting performance, as well as alloy production, recycling and environmental compatibility. Some of the important elements related to alloy production and recycling are addressed in the present paper.

Jan 1, 2006

By Juan Carlos Lozada

YURA S.A. es una empresa industrial cuyo principal actividad es la fabricación y comercialización de Cementos Portland y adicionados, conglomerados de albañilería y concretos. Asimismo proyecta la construcción de una nueva línea de producción de Clinker. En ese sentido, el presente texto señala el sistema de gestión que se utilizó para mejorar las prácticas sugeridas por el PMI (Project Management Institute) en la Guía del PMBOK, y cómo se aplicaron las diferentes herramientas a las situaciones particulares del mismo.

Sep 12, 2011

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014

By B. Winterberg, C. Lewis, M. Starkel, C. Johnson

Non-electric systems, specifically shock tube, have become the pyrotechnic detonator of choice over electric due to their safety regarding accidental initiation from stray radio signals. Typically, the best practice when hooking up shock tube systems is to have direct contact to ensure initiation. When gaps are introduced to the explosives chain, there is potential for detonation to come to a halt. It is understood that direct coupling is required between the various elements in the explosive chain to ensure detonation. This holds true whether tying in non-electric detonators, loading holes in a mining related blast, or priming a block of C-4. Poor contact and gaps in the explosives chain can lead to detonators firing out sequence, leading to increased vibration, air overpressure, and other undesirable blast results. Furthering work conducted in previous experimentation, a new study was conducted at the Missouri University of Science and Technology’s Experimental Mine in Rolla, Missouri to observe the initiation potential of an air gap and fragmentation on non-electric shock tube. A series of small test blasts were conducted using 50 grain detonating cord and fragments from a blasting cap to initiate a non-electric shock tube across an air gap of varying distances. The data collected in the high-speed imagery was used to analyze the velocity of the pressure fronts and blasting cap fragments used to initiate non-electric shock tubes across an air gap. It was found that the shock tube was sensitive to 50 grain det cord at a 5cm (1.97in) distance while parallel and 10cm (3.94in) when perpendicular as well as sensitive to frag from the electric cap out to 2.4m (7.87ft).

Jan 1, 2024

By Philippe Dumont

?Lay out of the tunnel section ?General ?Geology ?Tunnels methods ?Stations constraints ?Impacts on tunnels ?Design ?Programs

By Jean Igor Margem

Materiais sustentáveis estão sendo investigados para substituir os materiais sintéticos, os compósitos com matriz polimérica têm sido aplicados em componentes, tais como capacetes e blindagem para os quais a resistência em um requisito importante. O presente trabalho avalia a classificação energética de impacto Charpy e Izod da matriz de epóxi compósitos DGEBA / TETA, reforçado com até 30% em volume de fibras de malva contínuas e alinhadas (Urena Lobata, L). Os testes de impacto foram realizados em amostras padronizadas em matriz de epoxi obtidas por aplicação de pressão em molde com cura a temperatura ambiente por 24 horas. Os resultados mostraram aumento significativo da energia de impacto com a fracção de fibras incorporadas de malva. A superfície de fratura foi analisada por microscopia eletrônica de varredura, SEM. O desempenho das amostras incorporados com 30% de fibras, sofreu apenas ruptura parcial devido a dificuldades impostas ao quebrar-se as fibras, e, consequentemente, a natureza dos quais fendas tendem a propagar na interface entre a matriz de fibra / resina epóxi, o que ajuda a absorver a energia do impacto.

Aug 17, 2017

By H. S. Auvil, J. T. McCartney, J. D. Davis

"INTRODUCTION It is now generally recognized that the small-scale laboratory dilatometer method of test does not give results of much utility in predicting the expansion (or contraction) of a coal in a coke oven. The carbonizing conditions in the laboratory test differ radically from those in the oven; in this test, the charge is heated through the coking range of temperature as a whole, whereas in the oven, coking proceeds by layers parallel to the oven walls as each succeeding portion of the charge goes through the plastic range of temperature and coke formation sets in. The paths of the gases and vapors and the pressures set up are different in the two methods. Furthermore, the rate of heating in the test usually is much more rapid than in the oven. H. Koppers 5/ was perhaps the first to adopt apparatus and procedure whereby the layer coking of the coke oven could be simulated closely however, the heating progressed from one side of the charge only; later he experimented with a small coke oven with a movable wall heated from both sides. It is not clear how well the results in the later oven correlated with those of the earlier small test oven, but in a comparatively recent Koppers publication a modification of the original small test oven heated from one side is recommended 6/ Altieri 7/ was perhaps the first to experiment with the Koppers type small test oven in the United States and Brown- has tested a large variety of coals in a rectangular test oven of his own design heated from the sole or floor. Subcommittee XV of American Society for Testing Materials Committee D-5 is now making a study of the various methods proposed for determination of expanding and plastic properties of coal with a view to standardization. 9/"

May 1, 1939

By Edwards A. B

Occasional, sporadic and small occurrences of lollingite in the Broken Hill lode have been described,(l) mostly in the garnet sandstone in the foot-wall and under-wall of the Broken Hill lode. The lollingite contains appreciable percentages of cobalt and nickel and is regarded as an early mineral in the development of the lode; and, with the incoming of the sulphides, it has suffered considerable replacement by arsenopyrite. During the conversion of iron arsenide into the iron sulpho-arsenide, ilie nickel and most of the cobalt are removed in solution and are inferred to reappear in niccolite and other minerals that have been recorded among the later minerals of the Broken Hill lode. As a result of observations of the officers of ilie Broken Hill South Ltd., an occurrence of cobaltite can now be recorded which has developed by an analogous type of replacement.Cobaltite has previously been recorded from the Australian Broken Hill Consols lode in the vicinity of the rich deposits of silver, though not in contact with them. Cobaltite has been found in the northern extremity of the No. 2 lens of the Broken Hill lode at the 1,480 feet level of the Broken Hill South...

Jan 1, 1944

By James Goldberg, Mark Withey

The Material Service Thornton quarry is a multi-million annual production tons complex. Surrounded by busy surface highways, and divided by a railroad on the north/south axis and further divided by a major interstate highway on the east/west axis, blasting is a daily challenge. This paper deals with the problems of production blasting in an area adjacent to that interstate highway, and paralleling a busy four-lane highway. Discussion includes primary blasting issues such as borehole size, drill patterns and flyrock controls. Discussion also includes blast designs, timing schematics, smooth-wall blasting solutions, traffic and vibration concerns and many other factors influencing the success of this project.

Jan 1, 2006

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ??(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can be obtained through the addition of transition elements, but care must be taken as other elements might have adverse effects on the mechanical properties. The objective of this study is to determine the influence of Mn on the tensile properties of rheo-processed Al-Cu-Mg-Ag alloy A201. ThermoCalc software was used to predict the different phases that can be expected in the alloys, and scanning electron microscopy(SEM) with energy dispersive spectroscopy (EDS) was used to investigate the actual phases that formed. The influence of these phases on tensile properties is quantified. SEM and ThermoCalc revealed that there is an increased amount of the Al20Cu2Mn3 with increasing Mn. The tensile properties showed that high amounts of Mn do have adverse effects on the tensile properties of alloy A201, especially the ductility. Keywords Semi-solid metal (SSM) forming, alloy A201, intermetallics, Al20Cu2Mn3

Jan 1, 2011

By Sam Warren, Antonio Marinucci, Genesis Z. Figueroa, Anne Lemnitzer

Drilled Displacement Piles (DDP) provide an ideal deep foundation solution that combines the benefits of ground improvement with traditional advantages of piling systems. This paper consolidates data from 20 construction projects in which more than 30 DDPs were installed and tested axially. High quality site exploration data (e.g., Cone Penetration Test and Standard Penetration Test) were evaluated to derive geotechnical analysis parameters. The test sites consisted of mostly mixed soil types with strongly stratified layers of sand, silt, and clay. Pile diameters ranged between 40 cm and 61 cm. Test results were compared with predictive methods developed specifically for DDPs as well as methods used in general geotechnical practice. The accuracy of the empirical methods is presented in terms of total pile capacity, pile length/diameter, and soil type. The large majority of all examined methods underpredict the in-situ pile capacities. It was also found that the difference between the tested and predicted capacity is strongly related to the level of improvement in the surrounding soil due to the piles’ installation. A general comparison between predictive axial accuracy and the observed level of ground improvement upon installation is also discussed.

May 1, 2022

By M. S. Miller

With prevailing assumptions that plentiful domestic coal reserves will be available for meeting our Nation’s expectations for on future low emission, coal-fired power plants, major government funding in Clean Coal Technology, and Carbon Sequestration Programs continues to be aggressive. However, after more than a decade of cutbacks in funding for domestic coal-related programs and personnel, there is a growing concern that adequate quantification and qualification of our Nation’s coal reserves is increasingly being compromised. This paper will define the growing concerns and dichotomies that continue to increase, and address the decreasing number of fossil fuel mapping and assessment programs by Federal and State programs.

Jan 1, 2004

By Alan A. Campoli

The mining industry has long been searching for an effective structural application that prevents weathering and falls of loose rock, debris, and sediment. J-Crete is a fiber-reinforced, engineered, cementitious composite rock application that is designed, tested, and successfully utilized as such a material. Laboratory evaluation of J-Crete material properties has shown the final compressive strength to be in excess of 7,300 psi (50.34 MPa), with 24 hour strength in excess of 1,500 psi (10.34 MPa). The flexural tensile strength is in excess of 600 psi (4.1 MPa) and is provided through a unique combination of polyvinyl alcohol (PVA) fibers activated by a proprietary liquid additive that prevents them from clumping and enables even distribution throughout the grout. Tensile bond strength in excess of 350 psi (2.4 MPa) at 28 day cure tightens the strata and holds loose material in place. Practically impervious to gas and liquids, J-Crete protects strata against long-term weathering, does not require screening to be effective, and has proven to be a successful waterproofing material. J-Crete has demonstrated the potential to alleviate coal mine roof cutters in soft, wet clay formations. J-Crete reinforces coal mine ribs by bonding directly to the rib, conforms to the strata, strengthens the rib, and eliminates sloughing due to long-term weathering; stabilizes coal mine entries by bonding directly to the brow and roof, and creates a monolithic shell with double reinforced corners.

Jan 1, 2012

By Everton Pizzio

Parafusos utilizados para fixação de partes submetidos a carregamentos cíclicos estão sujeitos a falhas por fadiga. No estudo do conjunto carcaça/corrediça de um compressor fixado por parafusos prisioneiros - ISO M24x3, que fixam o flange da corrediça falharam prematuramente por fadiga. O objetivo deste trabalho é desenvolver uma metodologia para otimizar o desempenho em fadiga do conjunto parafusado. Para tanto, foram realizados ensaios de fadiga visando o melhor processo de fabricação no desempenho em fadiga. Observou-se que o processo de laminação da rosca seguido de tratamento térmico é o mais adequado para o caso em estudo. A conclusão principal foi que a configuração atual de união do flange com a carcaça, resulta num baixo índice de aperto que é verificado através das cargas máximas que são transferidas diretamente ao parafuso e que aumentando o comprimento do parafuso através da inserção de uma bucha extensora, aumenta a vida em fadiga

Aug 17, 2017