Search Documents

Yallourn brown coal and its characteristics have been the subject of innumerable papers and discussions. The Lurgi process adopted for the production of Towns gas by the gasification of brown coal has been described frequently in literature.The application of the Lurgi process for the gasification of Yallourn briquettes has naturally lead to some unexpected problems. Rather than attempt to review the whole field of experience gained in the first two years of operation of the gasification plant at Morwell, this paper attempts to describe two problems encountered, peculiar to the fuel used, and the steps taken in overcoming them.THE PROCESS AND PLANTTo clarify the conditions surrounding the problems, it is necessary to briefly describe the gasification and cooling processes and plant.Brown coal briquettes are gasified in a pressure generator, using a mixture of steam and oxygen as a gasifying medium. Crude gas produced in the generator is washed and cooled in the waste heat boiler and coolers. Figure 1 shows an arrangement of the generator and coolers. The gasifying medium enters the generator through a hollow shaft in the base. This shaft drives the grate, which has three purposes: (a) to distribute the gasifying medium into the fuel bed; (b) to extract the ash from the fuel bed; (c) to support the fuel bed.Briquettes enter the top of the generator through the coal lock chamber and the fuel bed is maintained at a reasonably...

Jan 1, 1960

By B Moynihan

The Roa Opencast Coal Mine is situated at the north-eastern end of the Greymouth Coalfield. It lies on an eastern flank of the Paparoa Range, 16 km north-east of the town of Greymouth on the West Coast of the South Island. Road access is via a sealed road from Blackball to Roa, then by a 5.3 km all weather, gravel road, which gains 340 m in elevation from 190 m RL at Roa to a maximum height of 530 m near the opencast.

Jan 1, 1993

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By E. A. Brocchi, D. H. Gameiro, P. K. Jena

Carbon tetrachloride was found to be a very efficient chlorinating agent for anatase concentrate, even at the low temperatures that were investigated (250-400 degrees C). For example, at 400 degrees C about 90% of the anatase concentrate was found to have been chlorinated within 60 minutes

Jun 13, 1905

By James Dunn

“The strongest argument of the detractor (of mining)is that the fields are devastated by mining operations ...They argue that the woods and groves are cut down, for there is need of an endless amount of wood for timbers, machines and the smelting of metals. And when the woods and groves are felled, then are exterminated the beasts and birds, very many of which furnish a pleasant and agreeable food for man. Further, when the ores are washed, the water which has been used poisons the brooks and streams, and either destroys the fish or drives them away.” Georgius Agricola, 1556, De Re Metallica, translated by Hoover, 1950. Technical problems associated with the cleanup of historic mines are not new. Nor are they unique to the mining industry or the governmental agencies addressing them. Both face the same issues and challenges of defining the problems, evaluating remediation options and finding the most economic and effective solutions.

Jan 1, 1999

By A. Roca, G. Ríos, I. Ruíz, M. Cruells

Flash Smelting Furnace (FSF) hot dust-laden is cooled in a waste heat boiler (WHB) and then dedusted in electrostatic precipitators (ESP’s) before being treated, together with the Peirce Smith Converters off-gases, in the sulfuric acid plants for SO2 removal. FSF dust is sulfated by SO2 and O2 in the WHB. Typically, 70% of the dust from the FSF drops in the WHB while the remainder is caught in the ESPs. The collected dust is recycled to the FSF for Cu recovery. Some smelters have developed hydrometallurgical treatments to recover Cu from the dust; impurities, such as As and Bi, are bled as leach plant residues. This paper presents a study (laboratory scale), of leaching the FSF dust, generated in Atlantic Copper Smelter using the weak acid bleed from the gas scrubbing/cooling section (GSCS) of sulfuric acid plants. Leaching was performed with 0.5 mol L-1 sulfuric acid concentration, 60ºC, and a solid/liquid ratio 1/3. After leaching, H2O2 was used for arsenic and iron oxidation. pH was adjusted for precipitation of arsenic and iron as scorodite or as scorodite and arsenical jarosite. The precipitation was carried out at 95ºC during 3-6 h. Liquids after precipitation are suitable for subsequent treatments of electrolysis. INTRODUCTION The copper smelter dusts are usually recirculated totally or partially to the flash furnace. This practice increases the amount of impurities feeding the furnace. Some authors have developed processes for treatment of these materials for copper and zinc recovery and for arsenic, antimony and bismuth inertization. The processes for the treatment of copper smelter dusts can be pyrometallurgical (Yu, 1987; Carter, Vance, Aldridge, Zaw, & Khoe, 1994; Fu, Jiang &Wang, 2000), hydrometallurgical, or mixed processes (Yin et al, 1992; Mulale, Mwema, & Mashala, 1999; Gorai, Jana, & Khan, 2002). Hydrometallurgical processes have been extensively studied and, in some cases, applied to an industrial scale. The most important chemical reagent proposed for leaching the dusts has been sulfuric acid (Roman-Moguel, Plascencia, Pérez, & Garcia, 1995; Gabb, & Evans, 1997; Larouche, 2001; Morales, Cruells, Roca, & Bergó, 2010; Cáceres, Cruells, Morales, & Roca, 2012; Ecometales, 2013; Yang, Fu, Liu, Chen, & Zhang, 2017). Processes developed in alkaline media, and in some cases with the presence of sulfide, have also been carried out (Gabler, & Jones, 1988; Morales, Hevia, & Cifuentes, 2009; Alguacil, Garcia-Diaz, Lopez, Rodriguez, & Alonso, 2013), as well as by using a bioleaching process (Massinaie, Oliazadeh, & Seyed Bagheri, 2006; Bakhtiari, Atashi, Zivdar, Seyedbagheri, & Fazaelipoor, 2011).

Jan 1, 2019

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

By Guy Chevalier, Jean-Guy Chartrand, Louis Barrette, Daniel Michaud, Michel Fortin

"COREM has developed, specifically for the mineral industry, a mobile laboratory using the Laser-Induced Breakdown Spectroscopy (LIBS) technique. It has been used to perform onstream analysis (OSA) of the chemical composition of slurries in both gold-ore and iron-ore processing plants. Industrial tests have been carried out respectively at La Mine Doyon (Cambior), a gold-ore processing plant near Rouyn-Noranda, Quebec, and at QCM's iron-ore pelletizing plant in Port-Cartier, Quebec. The aim was to demonstrate that the LIBS technique is capable of providing information that meets the needs for process control. C, Si, Ca, Mg, Mn and Al were the elements targeted on iron ore while Cu, Fe, Ag and Au were targeted for gold ore. The results obtained meet or exceed the requirements for process control and consequently clearly show that the LIBS technique is suitable for industrial applications.The feasibility of OSA, through in-plant validations using COREM’s LIBS mobile laboratory, has been demonstrated in four essential aspects: slurry sampling, LIBS chemical measurement, robustness for continuous operation, and functionality for industrial operators.INTRODUCTIONThere is a general need for optimization in the mineral industry. Process control is a favoured means to achieve this goal (McKee 1991). Real-time knowledge of process status is the key to effective control (Da Silva 1994). Only a few techniques, such as XRF, NMR and digital imaging, are currently amenable to chemically monitor industrial processes (Braden 2002). LIBS is an emerging technique with appealing characteristics for on-line and real-time measurement of bulk material (Lorenzen 1992, Palanco 2000). While our ultimate goal is to provide our industrial partners with performing monitoring tools, a shorter-viewed objective is to demonstrate the feasibility of developing a LIBS system for OSA. The LIBS technique has shown interesting capabilities for measuring solids, liquids, dusts and gases. Our work has focused on mineral slurries (Barrette 1999 and 2001, Turmel 1999). Special equipment is needed to perform in-plant validations. A mobile laboratory based on the LIBS technology has been assembled for this task."

Jan 1, 2004

The Bureau de Recherches Geologiques et Minieres (BRGM) (a French Government-sponsored geological and mining agency), through international experience gained over many years, has become very skilled in alluvial prospection, particularly for diamonds. The research laboratories within the BRGM have also been active in creating new mineral processing equipment, some of which is directly applicable to such prospection. One such development, the mobile prospection unit, is described and its application in mineral exploration is demonstrated by a consideration of the diamond search in Australia and the general exploration of the Massif Armoricain (France). Because this latter study was fundamental in the development of the concept of 'mineral-geochemistry', and its application in mineral exploration, it is also briefly described.

Jan 1, 1971

By José Ramiro Esteves Ramos

Características microestruturais são determinantes para as propriedades não ôhmicas de materiais varistores, uma vez que elas se relacionam com o coeficiente de não linearidade das curvas U x I, com a capacidade de absorção de energia, e com o seu grau de confiabilidade. O presente trabalho tem por objetivo a análise composicional e microestrutural de um material varistor comercial a base de ZnO dopado com diversos óxidos, além de comparar a eficiência dos ataques químico e térmico para a visualização das imagens em MEV. Os resultados obtidos condizem com a literatura onde foi observada a predominância de grãos majoritariamente compostos por ZnO com a presença de segregações constituídas de diversos elementos e concentradas nos contornos de grão. Quanto aos ataques, foi notável uma melhor qualidade das imagens quando se adotou o ataque térmico do ponto de vista da visualização dos contornos de grão. O ataque químico, por sua vez, demonstrou ser mais eficiente na elucidação das fases segregadas e na revelação da porosidade do material varistor.

Aug 17, 2017

By H. E. Dresch

This report summarizes the work accomplished under Bureau of Mines contract H0188068. The contract required design and construction of a high voltage (7.5 KV) explosion proof cable connector for use on underground coal mine drag cables. A connector was constructed with elastomeric phase insulators that provide insulation shielding throughout the connector length. Connector housing was made of flame resist-ant cast poly urethane with no exposed metal components. Electrical and mechanical testing of the completed coupler resulted in satisfactorily meeting most of the design testing requirements.

Jan 1, 1981

By Gustavo Henrique Bolognesi Donato

Este trabalho apresenta o desenvolvimento de critérios objetivos para a garantia de validade da mecânica da fratura elasto-plástica monoparamétrica, utilizando o parâmetro integral J como descritor dos campos de tensões, deformações e deslocamentos à frente de um defeito do tipo trinca. O mais importante na vertente monoparamétrica da mecânica da fratura é garantir que os campos de tensões no corpo de prova laboratorial sejam comparáveis com os existentes em uma estrutura real para cujo projeto as propriedades retiradas do corpo de prova serão utilizadas (conceito este denominado similitude). Para estabelecer critérios objetivos para a existência de similitude, esse trabalho comparou os campos de tensões obtidos de estruturas de referência sob alta triaxialidade de tensões (MBL) com aqueles obtidos de corpos de provas de mecânica da fratura em escala de laboratório. A matriz de análise permitiu a determinação dos limites de deformação M para geometrias C(T), SE(B) e SE(T) de diversas configurações e para uma faixa de propriedades de material característica de aços estruturais aplicáveis a vasos de pressão e dutos. Os resultados demonstram a baixa restrição à plasticidade de corpos de prova SE(B) e SE(T) com trincas rasas e os efeitos de profundidade de trinca e espessura nos resultados de M. Ainda, alguns comportamentos inesperados foram evidenciados, como no caso em que (para condições particulares de profundidade de trincas) corpos de prova mais finos apresentaram maior restrição a plasticidade do que amostras mais espessas. Sendo assim, o trabalho oferece uma base objetiva para que a similitude seja garantida nas avaliações de integridade estrutural baseadas na mecânica da fratura elasto-plástica suportada pela integral J, seja com seus valores críticos (Jc) ou curvas J-R.

Aug 17, 2017

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that affects the net expansion of the change in both industrial and test ovens. Various test results have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; out no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors. While investigating the reactivity of cokes made by the BM-AGA method,6/ Reynolds7/ found that granular low-temperature cokes shrink considerably then reheated to higher temperatures. This shrinkage was large enough to influence the behavior of the charge (net expansion or contraction) in a coke oven to a marked extent. Since that time the Bureau of nines has investigated the shrinkage of coke different methods, all of thick had one common objective - the elimination of the effect of other factors, such as swelling in the plastic range, which could either partly or completely mask the shrinkage of the coke. Only parts of these studies have been published8/9/ in abbreviated form in]

Jan 1, 1940

By Charles Stone, Madan Naik, Drupad Desai, Karel Rossler

Planning of New York’s new subway line dictated the location of shallow underground station caverns and track crossovers. Clear span openings ranging from70 feet to 100 feet and lengths in excess of 1000 feet, coupled with low rock cover ranging from 25 feet to 40 feet required judicious selection of construction methods, equipment, and proper sequencing of the excavation stages. Rock classifications alone could not predict the behavior of the rock mass during construction. A robust design procedure that considered most of the important aspects of rock behavior and elements of shallow tunnel design, minimized the negative impacts of variable geotechnical data. This paper describes the intricacies of the planning and design of the $16 billion Second Avenue Subway with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2005

By Fred C. Bond

A study of the settling and thickening of finely divided pulps was undertaken with the object of obtaining certain fundamental relationships, with resulting improvements in the design and operation of mechanical equipment. The subject has been treated in two parts: testing and batch thickening, and continuous thickening, including calculations of capacity and dimensions. Part 1. ? Testing and Batch Thickening The usual method of making thickening tests is to agitate the pulp with a plunger in a graduated glass cylinder and let it settle, while recording the time rate of settling. The settling rates corresponding to different pulp dilutions are found, the ultimate dilution obtained is measured, and the necessary thickener area in square feet per ton of dry solids per 24 hours is calculated, for each pulp dilution. The largest area found is used in selecting the proper thickener size.

Jan 1, 1946

By Bianca Harue Ueharar

Os métodos de pré-concentração, dentre os quais podemos destacar o gravimétrico, magnético, peneiramento e ore sorting, eliminam grande parte da massa a ser alimentada na usina, o que consequentemente impacta nas características do material que irá alimentar a moagem. Assim, este trabalho busca fazer uma comparação no desgaste de circuitos de moagem com e sem a pré-concentração em minérios de baixo teor. Através de ensaios laboratoriais de AI de Bond, foi obtido o valor da abrasividade e com isso é possível estimar o consumo de material de desgaste e revestimento dos circuitos. O estudo indica que o resultado é benéfico pois, eliminando-se mais da metade da massa, o desgaste dos equipamentos decai de forma proporcional, com um ganho maior no caso do ensaio em que a abrasividade do material pré-concentrado é menor. Portanto, do ponto de vista econômico, além da pré-concentração ter baixo custo operacional, a redução nos gastos com revestimento e bolas na moagem diminui de forma muito significativa.

Oct 30, 2017

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By Felipe De Lucio Pezet

El presente texto analiza las hipótesis sobre los pernos de roca, así como las particularidades de las teorías de los pernos cementados y sus sistemas de sostenimiento.

Jan 1, 1978

By Rubén Céspedes

El carbón es un combustible utilizado en la industria del cemento -en tanto fuente de energía calorífica para el uso alternativo o combinado del carbón. Por ello, el presente texto señala el empleo del carbón en la industria minera a través de un estudio de factiblidad que indique la rentabilidad del cambio y sus aspectos como características del carbón a utilizarse, innovaciones a equipos a montar y la influencia del carbón a utilizarse, así como se plantea la conversión del petróleo al carbón

May 1, 1985

By A. J. Martin

The Tri-State, or Joplin, zinc and lead mining district in south- western Missouri and adjoining, parts of Kansas and Oklahoma is one of the great mining districts of the world. It is in flat-lying or gently rolling agricultural country near industrial centers and coal, oil, and gas fields. The nearly horizontally, lying bedded rocks in which the ore bodies are found were originally limestone but are now largely chert containing minor percent- ages of dolomite and other minerals. The ore occurs in nearly vertical fis- sure zones, large and small, and in blanket (sheet-ground) deposits. The mining depth ranges from surface diggings to $50 feet. The average tenor of the ore mined, in recent years is much lower than that of ore produced in other large zinc and lead districts of the United States. Mining and mill- ing costs are low because of the shallowness of mining, amenability of ores to concentration, efficiency resulting from long experience of management and labor, and other factors. The operators comprise many small and medium-size producing companies and partnerships, as well as individuals and a few larger producers. About 7,000 men are employed in the mines and mills during normal industrial activity. The concentrates produced are sold f.o.b. the mill bins to local representatives of smelting companies at prices quoted on the Joplin market. The productive life of the district began with the discovery of lead near Joplin in 1848, but output was not large until after mining for zinc began near Granby in 1871. In most of the intervening years through 1945 the district produced more zinc than any other field, and it generally ranked third or fourth in the United States in lead production. Figures compiled from sources given later in this paper show a total output for the district from the beginning through 1945 of 20,755,020 tons of zinc concentrates and 3,334,057 tons of lead concentrates valued altogether at $1,110,058,581 in the mill bins. The output, in terms of recoverable metals, was 10,609,408 tons of zinc and 2,529,121 tons of lead, valued in all, at the average yearly market prices of the metals, at $1,691,282,419. During the 39 years (1907-1945) for which complete figures are available, the annual output of the district fluctuated from 23 to 66 percent of the total United States mine output of zinc and from 5 to 18 percent of the total lead; the averages for the period were 40 percent for zinc and 11 percent for lead. peak yearly production was attained in 1926, with an output of 423,800 tons of recoverable zinc and 102;117 tons of lead. Since that yoar the production rate has trended downward, accentuated at first by the depression in the thirties and later ameliorated somewhat under the stimulus of heavy demand and higher metal prices during World War II; the output in 1945 was 139,274 tons of recovorablo zinc and 23,556 tons of load. The above figures show the groat contribution made by the Tri-State district in the past toward the country's supplies of primary zinc and lead, cspecially zinc. However, the district's production is expected to decline both in quantity and in proportion of total United States mine output unless important discoveries are made. Ore exposed in mine workings and extensive exploratory drilling done in recent years within and without the productive The

Nov 1, 1946