Search Documents

By D. S. Kingery

The data obtained from this study cover test areas that are gassy to ultragassy and pillared areas of different sizes and degrees of tightness. The methods of controlling ventilation, applying bleeders, and supporting bleeder entries varied in the different test areas. It was not possible to study all conditions likely to be encountered in coal mines. Undoubtedly, there are areas where bleeder entries, even though properly planned and maintained, might prove unsatisfactory. However, on the basis of this study, the following observations were made: 1. Tests showed that each bleeder system studied provided some movement of air through the pillared area; the quantities of air delivered to the pillar line, ranged from 23 to 82 percent, depending mainly on the extent to which bleeder re-turns were used as main returns from the section. 2. Pressure measurements taken across pillared areas showed maximum pressure drops ranging from 0.05 inch of water for a shallow gob to 2.69 inches for a very deep gob. The pressure differentials varied with the size and tightness of the gob but proved adequate to induce airflow across worked-out areas or through fringes of the gob to the bleeder return system.

Jan 1, 1957

By James McNally, Adam Stremcha, John MacGregor

With 13.7km of TBM tunneling in Atlanta’s hard gneiss well under way, drill and shoot work continues on several sites throughout the city. In order for the City of Atlanta to meet the consent decree imposed by the federal government, an aggressive construction schedule was a necessity. Construction consists of two deep, large diameter tunnels, four construction shafts, a pumping station, one overflow shaft, three large intake structures, and two connecting tunnels. Due to the multitude of blasting insensitive urban environments, a high standard of seismic and air-overpressure criteria, coupled with time restrictions, was adopted for the project. At any given time, drill and blast operations were under way at four of the seven sites requiring a certain amount of coordination between the TBM excavation, surface work, and the forces of Mother Nature. This paper addresses the challenges faced and the techniques used to safely and successfully complete the rock excavation of the West Area CSO Tunnel and Pumping Station project.

Jan 1, 2007

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By Stephen Tadolini

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of ?primary support? and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

Jan 1, 2007

At Appin colliery, geological structural analyses and investigations of roof conditions suggest roof failure may be attributed to vectorial stresses acting on underground openings, and inducing movement along inherent discontinuities in the surrounding rocks. Certain complex joint and fracture patterns tend to exhibit the effect of this movement resulting often in local deterioration in natural support.The following conclusions are drawn.1. Roof failure is related to the inherent nature of the roof rocks, the presence of mechanical discontinuities, and the vectorial stresses imposed upon it.2. Roof failure is not necessarily related to the statistically most prominent jointing.3. Colliery development approximately parallel to the direction of the statistically most prominent jointing sometimes results in favourable roof conditions.4. The maximum principal stress is the resultant of those vectorial stresses acting upon a mine opening and may be inferred from roof adjustments to those stresses after mining.5. Statistical analyses of jointing in the mine workings can provide clues to the tectonic force or forces which have been regionally or locally influential.6. There is a probable relationship between mining induced fracturing, jointing, and micro-fractures in quartz grains, within the sediments of the mine roof.

Jan 1, 1970

By Jim Owens

The methodology of quarrying changed significantly in the Indiana limestone industry in the 60 years between Sept. 11, 1941 and Sept. 11, 2001. The former was the date of the Pentagon groundbreaking ceremony, while the latter was when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on Sept. 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction(and Indiana limestone) industry can accomplish when working toward a common goal.

Jan 1, 2005

By George Saliba

This report disucsses the formulation of a mathematical model for the steering of a conveyor belt by a flat return idler and a troughed idler under various loading conditions. Significant parameters associated with belt training are identified. The generation of a skewed flat return idler model in terms of a steering force and self-aligning torque is presented. Development of the mathematical model for the flat return steering idler is illustrated for the case of no circumferential slip occurring and for the assumption of a bidirectional slip mechanism. Experimental results supporting the theoretical analysis is presented.

Jan 1, 1977

By David C. Oyler

The Bureau of Mines conducted research at the 9-Right Section of the Olga Mine to determine the cause of bumps and aid in the development of appropriate control techniques. The purpose of this paper is to identify the factors which affect the occurrence of bumps at the Olga Mine. These factors have been broken down into two categories, in situ and mining related. The in situ factors include those conditions which exist prior to mining, such as variations in lithology and overburden, presence of jointing, the composition and the physical properties of the rock, and the original stress field existing in the coalbed and adjacent strata. The mining factors include the mining sequence, changes in stress in the coalbed and adjacent strata during mining, rates of convergence, and the pattern of failure of the coal and adjacent strata. The factors which appeared to have the greatest effect on bumping were the overburden, the lithology of the roof and floor rock and the physical properties of the rock. The roof rock is generally a massive, stiff sandstone which does not break until coal pillar extraction is complete. The immediate floor is a strong shale which generally grades into siltstone and then into sandstone. The overburden at 9-Right ranged from 990 to 1,600 ft. Secondary factors appeared to be the in situ (pre-mining) stress and the mining sequence. When barrier pillars were split., pressures measured in hydraulic cells (Borehole platen flatjacks) located in those barriers showed large pressure increases, and the incidence of bumps increased, especially when the barriers were near old gob areas. The pillar extraction system used at Olga, where three rows of pillars are mined concurrently, appears to reduce pillar loads at the face areas, thereby reducing the exposure of men and equipment to the risks of bumps during mining operations. The horizontal components of in situ stresses at Olga were found to be nearly the same as those at 5 other mines in southern WV, where humps were not common, so it appears that horizontal in situ stress alone is not a major influence on bumping at the Olga Mine.

Jan 1, 1987

By Lloyd R. Nelson

Selective carbothermic reduction is the preferred method of treatment of electric arc furnace (EAF) dust (listed hazardous waste, K061). The process maximizes the recovery of recyclable constituents by concurrent production of saleable zinc metal (directly condensed from the furnace off-gases), an innocuous, disposable iron oxide-rich slag, and some metallic iron. Results of a mineralogical investigation of a foaming slag produced during selective carbothermic reduction treatment of EAF dusts are presented. Wiistite and tricalcium silicate were identified by reflected light microscopy as the primary crystalline phases contained in a glassy matrix, but this technique failed to reveal any solid phases that could have significantly contributed to foam stability. It was concluded therefore, that the foam had been unstable, and had been primarily generated by copious gas evolution associated with the sudden reduction of the slag by an inadvertent addition of carbonaceous reductant. This is consistent with the susceptibility to foaming, when subjected to sudden excesses of carbon, of the slags produced by selective carbothermic reduction, because they still contain unreduced components such as iron oxide.

Jan 1, 1994

By Scott, Turner

IN 1933, the monetary metals were produced in a ratio of 6.7 oz. of silver to 1 oz. of gold, the lowest relatively for silver since the period from 1851 to 1865. At the beginning of that period, the virgin placers of California -and Australia began producing almost simultaneously; in consequence, there was an abrupt fall in the high silver side of the ratio that had prevailed through the centuries after America was discovered. The output from the Comstock and other silver-bearing lodes, located a decade after this influx of new gold began, soon restored the production ratio to its former proportion, that is, a relatively large weight of silver compared to gold.

Jan 1, 1934

By Kennedy G. L, Evans D. G

The development of the carbonization of brown coal briquettes to produce a hard char suitable for use in place of imported hard coke has continued in Victoria, and an experimental carbonization plant has recently been commissioned at Morwell by the Gas and Fuel Corpora.tion to assess the prospects for the commercial production and marketing of hard char in Victoria. The char offers advantages in its very low ash content and its uniform lump size, while the indications are that it could be marketed at a price competitive with that of imported hard coke. The hard char is unique amongst metallurgical fuels in combining a high reactivity with high physical strength, and research by the University of Melbourne into its utilization in foundry cupolas for melting iron has shown how modifications could be made to take advantage of these properties. An 18 inch experimental cupola has been built to test in practice the predictions made from this fundamental research.INTRODUCTIONSteady development has continued in Victoria from the promising laboratory researches at the University of Melbourne which were reported to the 1955 Annual Conference of The Institute (Worner, 1956). This work had shown that a hard lump char could be produced by the high temperature carbonization of standard industrial briquettes by careful control of the heating conditions, and that the special briquetting techniques adopted in Germany were unnecessary with Yallourn brown coal. Continuation of this research has led to the refinement of carbonization techniques and has increased the strength of the char until it has equalled that of conventional metallurgical cokes.

Jan 1, 1960

By P. A. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The recovery of cyanide from a gold mill solution containing high levels of copper (400 mg/L to 900 mg/L) using the AVR process was evaluated. It was determined that acidification to pH 2 to 3 provides a suitable balance between HCN generation, copper precipitation and acid consumption. A short pilot plant campaign showed that ~75% of the feed WAD cyanide was recovered while the remainder precipitated along with copper upon acidification. The acid consumption averaged 3.5 g H2SO4 per litre of solution. The copper precipitate, consisting mostly of CuCN and CuSCN, was readily separated from the solution by gravity. The volatilization of HCN in countercurrent packed columns averaged 98.7% efficiency. Reabsorption of HCN was practically 100% in NaOH solutions and slightly lower in a lime slurry. Basic volatilizer design parameters applicable to a large-scale operation were determined, including the Henry’s Law constant and the mass transfer coefficient of HCN gas.

Jan 1, 1998

By D. R. Spears

As part of its mission to develop technology to assure a continuing supply of minerals, the US Bureau of Mines has investigated the flocculation of a Stillwater, MT, chromite ore. The ore was flocculated at different solids contents and at different stirring speeds to determine the importance and effect of hydrodynamic factors. In acidic and basic pH, the chromite ore was flocculated with high molecular weight polyacrylamides differing in the degree of hydrolysis. Polyacrylamides were found to bind to chromite ore particles through hydrogen bonding. The anionicity of the polymer and the pH affected the degree of polymer-particle interaction, which in turn affected polymer conformation at the surface. A polymer conformation with many loops and tails was used to explain high flocculation efficiency. It was found that such a conformation could compensate for poor hydrodynamic conditions.

Jan 1, 1992

By Gennaro G. Marino

This paper summarizes and evaluates data on mine subsidence ground movements and associated damage for houses in Illinois. Based on the data collected, the response of homes to subsidence ground movements is expressed in terms of repair costs. A damage criteria is then proposed that relates the ground movements and damage levels. The data were collected as part of a comprehen¬sive study performed for the Illinois Abandoned ?Lined Lands Reclamation Council, A -M-RC, by the Civil Engineering Department at the University of Illinois, and probably will be published in late 1934 by the council. The study concentrated its efforts on surface ground movements and the effects to houses over abandoned room and pillar mines. The resultant surface subsidences are commonly dish or bowl shaped and are termed sags. Method of Analysis The steps in analysis used to arrive at the proposed damage criteria are: 1. Canvas and rap subsidence damage in houses, 2. Assess the associated ground movements, 3. Estimate the damage repair cost, 4. Develop a damage/repair level classifica¬tion, 5. Correlate the associated ground movement, damage/repair level and home construction type, 6. Propose a damage criteria.

Jan 1, 1984

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy, H. S. Ray

The Ni oxide was reduced with a CO-CO2-N2 gas mixture and the effects were observed of process variables such as roasting temperature, time and CO partial pressure. Extraction of over 90% of Ni was achieved by ammoniacal leaching of ore that had been reduced for 1 h at 760 degrees C under a gas mixture with a volumetric CO/(CO+CO2) ratio of 0.57. The kinetic data were found to conform to the Ginstling-Brounstein equation. The applicability of this model was confirmed by evaluating the apparent activation energy with the use of independently constructed differential and integral plots, which showed an excellent match

Dec 1, 1995

By Sofoulis J

In the Archaean of the Kalgoorlie-Norseman area, the layered rocks have been subdivided into two sequences, both containing basic igneous rocks and sediments. The lower sequence is distinguished by the presence of acid volcanic flows and large acid sills. The upper sequence is unconformable on the lower one.In some areas, clastic sediments become coarser and pass into conglomerates. Th:s passage is accompanied by thinning of the beds.These features and their distribution suggest a basin of subsidence flanked by areas of shore-line conditions.Repeated igneous activity, including vulcanism, has occurred along the flanks of this basin. These different igneous and sedimentary environments have played an important part in the primary distribution of metals.A chronology of all basic and acid igneous activity, as well as sedimentat:on, has been established for the Precambrian of this area.INTRODUCTIONThe subdivision of Archaean rocks into those of basic igneous or of sedimentary origin has formed the basis for the nomenclature appearing in past literature. These subdivisions were distinguished as greenstones (predominantly basic igneous rocks) and whitestones (predominantly sediments), and it was generally accepted that the greenstones were stratigraphically lower in the sequence than the whitestones.Recent studies show that, between Kalgoorlie and Norseman, basic igneous rocks interfinger with and pass laterally to sediments, and that basic volcanic rocks occur at different stratigraphic levels. Younger Precambrian. units are also...

Jan 1, 1965

Remediation of Mine Seepage at Batu Hijau

Sep 13, 2010

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

By Andrew Howard

As the mining industry moves further into developing countries in search of new resources, its role in international development is coming under increasing scrutiny. This is a trend that is likely to accelerate, along with the potential for headaches among managers in the industry. Public interest in development and environmental issues is rising as faith in “big business” falls. This has strengthened nongovernmental organizations (NGOs) campaigning for sustainable development. And it has put more pressure on banks, governments and development agencies to curb corporate misdemeanors. Developing world governments are also becoming emboldened to reject previously agreed terms they do not consider equitable. The mining industry has begun to formulate a response to these pressures but must go much further. Societal and environmental issues must move from public relations to core strategic thinking. Abiding by rules or codes is not a relevant response. Instead, genuine support for sustainable development is required. This will involve delegating the responsibility for engaging with local communities to on-the-ground staff and developing a dialogue with local stakeholders rather than conducting an initial assessment and disengaging.

Jan 1, 2006