Search Documents

By Charles K. Rose

This paper presents some research studies of the rotary drilling of oil shale at the Bureau of Mines Oil-Shale Mine, Rifle, Colo. The experimental procedures and the rotary drill test equipment are described. Theories of rock drillability, rotary bit cutting action, and bit design are presented and discussed. The actions of various bit designs are analyzed and compared with the observed results of actual drilling tests. A cost estimate is made for drilling Colorado oil shale.

Jan 1, 1955

Large GDP increases in the Pacific Rim countries have been accompanied by similarly large increases in demand for oil products. In the case of residual fuels, this demand has been tempered by the substitution of other energy products such as coal or gas. In the region's developing and newly industrialised nations, it has not been possible to make the very large investments in infrastructure which allow other energy sources to be used for transportation. As a result, GDP growth has been mirrored in the demand growth for automotive fuels. Other non-substitutable products such as lubricants have also benefitted by the region's GDP growth.   The combination of a number of years of sustained growth, coupled with increasing quality requirements is now stretching the upgrading capacity of the region's refineries. IT, as seems likely, the region continues to enjoy a high GDP growth rate, then this will be accompanied by increasing reliance on finished products coming out of the Middle East.   The owners of the most simple form of refinery in which crude is simply distilled and the naphtha reformed into petrol will face major capital investments. If they decide not to bear this cost, they will face increasing problems in selling their surplus residual fuel oil at an economic price. Quality will become an increasingly important issue. Not only in the well publicised areas such as unleaded petrol, but also for products such as lubricants which play a major role in the efficiency of modem equipment. Quality of service such as hours of opening, ease of access, and service station facilities will also become increasingly important as the oil companies use these to attract customers and gain brand differentiation.

Jan 1, 1990

By Ihsan B. Tulu, David F. Gearhart, Gabriel S. Esterhuizen

"Ground deformation and support response was monitored in a longwall gateroad as part of a research project into gateroad stability under changing loading conditions. In this study, instrumentation was installed in a gateroad located between two active longwall panels. The first panel to pass was the second panel in the district, and the second panel to pass the instrumentation sites was the third panel in the district. All of the panels in the district were right-handed. All of the instrumentation was installed in the number one entry, the tailgate, the second panel to pass the instrumentation sites at a mid-pillar location, and at an outby intersection location under about 600 feet of cover. The instrumentation included roof extensometers, cable bolt load cells, hollow inclusion cells, borehole pressure cells, standing support load cells, and convergence sensors, and a multipoint borehole extensometer. The roof extensometers measured roof convergence and sag. The cable bolt load cells measured the roof load applied to the cable bolts in the secondary support array. Hollow inclusion cells measured the magnitude and direction of the principal and shear stresses. The borehole pressure cells measured the stress on a pillar in the entry nearest to the second panel to pass the instrument site. The instrumented wood cribs in the entry nearest the second panel recorded the closure and load on the cribs, and the multipoint borehole extensometer in a pillar closest to the second panel recorded the location and width of cracks that occurred and total expansion of the pillar. This paper describes the effects of the changing stress caused by the first panel as it approached and passed the locations of the instruments on the opposite side of the gateroad system and the later effect caused by the second panel as it approached and passed the mid-pillar instrument location. The first panel passing caused significant loading at the mid-pillar instrument location, but not at the intersection location, while the second panel had passed the mid-pillar location and just arrived at the intersection location when the dataloggers needed to be removed."

Jan 1, 2017

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. Then enough circulars have been completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed by bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual mines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); ventilation; wage, contract end bonus systems, etc.

Jan 1, 1930

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

When Haematite Explorations Pty. Ltd. began prospecting for petroleum in 1960, there was only ill-defined geological evidence on the land bordering Bass Strait to support the belief that petroleum lay trapped in sedimentary formations beneath its shallow waters.A reconnaissance of the area, made in 1961 by the airborne magnetometer method, covered the waters and islands of the Strait and overlapped the Victorian and Tasmanian coasts. The survey indicated the presence of the Bass Basin (which is completely water-covered), assisted in outlining the Otway and Gippsland Basins, and showed that each basin contains sedimentary rocks over 10,000 ft thick. Information on the regional geology and minor volcanic activity was also obtained.Marine seismic surveys carried out from 1962 to 1965 defined these basins more accurately and showed the nature and structure of the thick sedimentary sections.Correlation of the seismic data with onshore wells identified the sediments as Tertiary and Mesozoic. Subdivisions of the former in all basins and the latter in the Otway Basin were made. These Tertiary and Mesozoic rocks are not seriously deformed and they have good prospects of containing petroleum.Possible structural and stratigraphic traps, recognized from the seismic record sections by petroleum geologists, are being tested by offshore drilling which began in 1964.

Jan 1, 1966

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By M. B. Shongwe

Pt-based alloys are being developed for high-temperature applications with the aim of replacing some of the currently used Ni-based superalloys (NBSAs) in the highest temperature applications. The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert than nickel and has a higher melting point, they can potentially be used at higher temperatures, up to 1300°C, and in more aggressive environments. Several experimental Pt-based alloys were studied at Mintek, and an optimum composition was found to be Pt84:Ahi:Ru2:Cr3 (at.%). On the basis of hardness and microstructure, a later study identified a new optimum: Ptr8:A111:Ru5:Cr6 (at.%). There are at least two Pt3A1 allotropes, and the high-temperature cubic structure has better properties than the lower temperature tetragonal form, and so needs to be stabilized. This work describes the latest results obtained in transmission electron microscopy (TEM) studies of the quaternary Pt-based superalloys. These results are both interesting and important, because the samples have a higher precipitate density compared to those from earlier work. The precipitate morphology is mainly cubic, with minor areas having irregular-shaped precipitates. The high volume fraction of the precipitates is a major breakthrough, since the objective of this work is to improve the alloys. A prior disadvantage was that the proportion of the precipitates was too low in samples before this work, especially compared with the work from Germany on Pt-Al-Cr-Ni¬-based alloys as well as the NBSAs. TEM -Pt3A1 diffraction patterns were studied, and for each diffraction pattern, many possible lattice point combinations were tried, with the angle between the lattice spots as well as interplanar spacings being calculated for each phase (cubic or tetragonal) to match the measured results. An overall analysis of the diffraction results indicates that the cubic phase fitted the experimental lattice points with much lower errors compared to the tetragonal phase. Thus, with the close match achieved with the cubic structure, the structure of -Pt3A1 precipitates is likely to be cubic. X-ray diffraction has been carried out on selected samples, and the results confirmed the presence of cubic -Pt3A1 and (Pt). Different X¬ray diffractometers were used to further verify the results, and the results were also compared with those from TEM.

Jan 1, 2012

Residual aeolian placers (RAPs) are formed by the wind, by preferential entrainment and removal of small and low-density detritusfrom a pre-existing, typically sedimentary sequence containing heavy minerals. Heavy minerals that are resistant to chemical alteration and either soft and malleable (gold), or extremely hard (diamond, sapphire, ruby, etc), are concentrated as a residual on the wind deflation surface, typically in the interstices between larger resistant clasts. RAPs form preferentially in arid or semi arid areas, where the vegetation is sparse or absent, and where topography and surface gradients are low, but may also form on beaches and in periglacial environments. RAPs consist of a continuous or discontinuous, planar or gently undulating horizon of heavy minerals in a single-clast-thick pavement of resistant pebbles, cobbles, or boulders, which mantles the present topography or palaeo-topography. Extreme wind erosion and surface deflation may condense the full pre-existing sequence into a layer of heavy minerals only. The grade of RAPs is substantially higher than in the precursor deposit, and commonly much higher than those typically found in most other placer types. Aside from their general occurrence as a thin pavement of resistant clasts, the best indicators of residual aeolian gold placers are the presence of wind-eroded stones (ventifacts) on the pavement, and the distinctive and unique shapes of aeolian gold grains themselves. The shape of the gold grains is progressively transformed by sand blasting during placer development, from grains with thickened rims, to toroidal grains on which the rims are æsplitÆ and peened inward toward the grain centre on one or both of the grain sides, to hemispherical or sub-spherical grains that are fully encapsulated by the in-turned rims. Gold that has undergone aeolian shape transformation is difficult to entrain and transport away from the site of aeolian concentration by anything other than mass movement or glacial processes. It is also easily retained by commercial recovery plants of any configuration.

Jan 1, 2004

By R. J. Fantel

The Bureau of Mines investigated the resource potential of 201 mines and deposits in 28 market economy countries and 17 mines and deposits in the U.S.S.R. and China. The 201 mines and deposits evaluated from market economy countries contain an estimated 34.2 billion metric tons of recoverable phosphate rock (at the demonstrated resource level), with Morocco and Western Sahara accounting for 61% (21 billion tons), followed by the United States with 19% (6.4 billion tons). The 17 mines and deposits evaluated in the U.S.S.R. and China contain approximately 1.5 billion tons of potentially recoverable phosphate rock. Potential annual capacity from low-cost, high-grade producing mines in the United States is estimated to decline significantly during the latter half of the next decade, and the United States will have to develop new, higher cost, lower grade mines in order to satisfy demand into the next century. Of the world's new production capacity which could likely be developed over the next decade, slightly over one-third could be produced at an estimated 1981 cost of $40 per ton or less, and about two-thirds would cost in the $40 to $50 range (including a 15% rate of return). In comparison, moot of the competing phosphate rock from producing mines in Morocco could be produced for under $40 per ton. The United States has sufficient demonstrated resources of phosphate rock (plus huge quantities at the identified and hypothetical resource levels) to satisfy domestic consumption for many years to come, but its future ability to compete in the major export markets against low-cost competitors is much more uncertain.

Jan 1, 1984

The use of solid state detector and radioisotope x-ray source for x-ray fluorescence analysis is illustrated by analysis for iron, copper, zinc, tin, and lead in about 700 samples taken from Australian mineral process streams. Limits of detection based on counting statistics (3 standard deviations) range from 0·001 to 0·004 per cent by weight element. The analysis accuracy was usualIy between 2 to 10 per cent (rms) of the mean element concentration and was determined by comparison with assays supplied by mineral companies. In most cases the main cause of error appears to be due to this assay and not the x-ray fluorescence technique.Some potential fields of application of solid state detector and radioisotope x-ray source for analyses in the mineral industry are indicated.

Jan 1, 1974

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By Jorge Ganoza

Algunos concentrados de plomo contienen contaminantes que afectan la comercialización del concentrado de cobre debido a aspectos ambientales, así como la calidad del producto final. En ese sentido, el presente texto busca la forma de minimizar la presencia del plomo y de bismuto en el concentrado de cobre, a través de la flotaciónpor chalcopirita. De otro lado, dado que el plomo y bismuto son elementos que tienen similar comportamiento durante la flotación, es factible aislar los minerales de plomo y bismuto.

Nov 1, 2012

By Jay S. Gunasekera

Metal parts are traditionally processed by either filly-liquid (e.g., casting) or filly-solid (e.g., forging) state. Semi-solid metal forming incorporates elements of both casting and forging. In 1991, Gunasekera(5) developed a model illustrating the influence of flow stress by the liquid fraction. The result fits Kiuchi's (1979)(7) experimental data quite well. This model assumed the liquid part is surrounded by solid as small pockets inside the material, which is opposite to the real practical situation. Since the melting usually first happens at the grain boundary, it is better to treat the semi-solid material as small metal crystal surrounded by liquid.

Jan 1, 1997

By Alain Blanchier, Gilles Gomez

Neighborhood pressure on quarries has become urgent to deal with quarry managers and operators must apply the most recent technologies and communicate it for long shelf life time exploitation, the quarry in which the work is located in urban or suburban environments needs to take into account blasting rules as well as site environment. The main problems to be addressed are:

Jan 1, 2009

The paper examines the design issues associated with the integration of mineral processing within underground mining systems. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins. The performance of such integrated systems in terms of productivity, economic and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefit, whilst underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems.

Jan 1, 2003

By Chen Dong, Yang Wenwang, Liu Zhineng, Tan Ming

"To meet the requirement of production expanding of a certain potash ore dressing plant in Xinjiang province of China, industrial test of XCF/KYF-50 flotation machine was performed to process potash ore. The tank of XCF/KYF-50 flotation cell is in U shape, 50m3 of volume. This flotation cell is able to suck slurry by itself, and can be arranged on the same base level without high difference. In this paper, two sets of XCF/KYF-50 flotation cells were adopted to replace 8 sets of 8m3 flotation cell in original flow sheet of flotation. Aeration rate, slurry suction capacity, power consumption and slurry suspension are investigated. The measuring results show the slurry suction capacity of the flotation cell is larger than 12.80m3/min and solid particles disperse evenly in the tank without deposition. Industrial test result indicates that the final grade of concentrate is 26.69% at the recovery of 90.95%, which is up to expected performance. XCF/KYF-50 flotation cell has advantages of high flotation efficiency, significant energy saving and reasonable configuration of automatic control system, this kind of flotation cell can meet the requirement of production expanding of this potash ore dressing plant well."

Jan 1, 2014

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Qingxiang Huang

Shallow seam coal field has the largest coal reserve in China. Mining in shallow depth causes serious problems. One of them is subsurface dewatering. In this paper, the physical simulating model was performed to study overburden movement and aquiclude stability in the shallow seam mining of Yushuwan coal field, China. According to the characteristic of clay aquiclude in the overburden, the proper simulation materials and proportions of mixture for simulating the plastic clay aquiclude layers and brittle bedrock layers were determined by the stress-strain tests. The physical simulating model was carried out to simulate the failure and caving process of the roof and overburden. Based on the simulating tests, it was found that the movement of clay aquiclude follows the movement of the underlying bedrock layers. The basic caving mechanism of the overburden roof strata was also presented. The tests also showed that the best way to control the stability of aquiclude is to reduce the subsiding gradient Ts. This research provides a foundation for further study on mining dewatering and water conservation.

Jan 1, 2006

By Marcilio do Carmo Silva

O circuito de flotação de Fábrica Nova é composto por três colunas de quatro metros de diâmetro e quinze de altura, equipadas com sparger’s tipo retrofit (misturadores), utilizando uma mistura de ar e polpa para geração de bolhas. As colunas operam em paralelo constituindo o estágio rougher. Os produtos gerados neste estágio são tratados em células convencionais (cleaner e scavenger). Com o empobrecimento do ROM proveniente da Mina de Fábrica Nova e conseqüente aumento de SiO2 na alimentação da flotação, fez-se necessário ajuste no circuito com o intuito de garantirmos qualidade competitiva do pellet feed de Fábrica Nova. Foram feitas alterações de rota do rejeito do estágio rougher, direcionando o mesmo para o rejeito final (no circuito padrão o mesmo alimentava o estágio scavenger). O rejeito do rougher e o rejeito do scavenger compõem o rejeito final da flotação. Um ajuste no percentual de sólidos da alimentação da flotação foi necessário para favorecer a coleta da sílica (saindo da ordem de 58-60% para 53-54%). Com esta manobra conseguimos retirar o excesso de SiO2 do circuito de flotação, possibilitando a geração de pellet feed com qualidade dentro dos padrões VALE.

Aug 8, 2018