Search Documents

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By K. A. Lapakko, D. A. Antonson

Fourteen samples of pyrite-bearing Archean greenstone rock (d < 6.35 mm, 0.04% < St < 1.22%) were characterized (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing. The only sulfide and carbonate minerals identified were pyrite and siderite, respectively. Quartz, chlorite and sericite typically comprised 90 to 98 percent of the mineral content. For the first 60 weeks, seven samples with sulfur contents less than or equal to 0.16% produced drainage pH values exceeding 6.0. Over this period, six of the seven samples with sulfur contents greater than or equal to 0.20% produced drainage pH below 6.0, with minimum values ranging from 3.2 to 4.7. The seventh sample (0.72% S) had a siderite content of 18%. Small amounts of magnesium and, to a lesser degree, calcium carbonates present in the siderite apparently dissolved to neutralize acid and maintain drainage pH above 6.0. Sulfate release rates generally increased as sulfur content increased, and the rates of pyrite oxidation estimated for individual samples were roughly half to five times that reported in the literature for the abiotic oxidation of pyrite by oxygen. Observed neutralization potentials ranged from 0.2 to 2.0 g CaCO3/g rock.

Jan 1, 2002

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company&apos;s operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has averaged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by persons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore transportation, persons falling, explosives, and asphyxiation. Accident Prevention The improvement of the safety record was obtained by a combination of many factors. In surveying the results at Andes for the past twelve years, it is possible to select some features of the present operation which have contributed to the accident record. The most important of these are: (1) good staff planning, (2) good equipment, (3) an alert safety organization, and (4) education and selection of the workmen. GOOD STAFF PLANNING As a result of good staff planning, the mine has good working conditions, namely, good ventilation, moderate temperatures and humidity, and good lighting. These factors not only reduce accidents but also improve efficiency. In haulage work, accidents have been reduced by having traffic move in a forward direction only. The latter makes possible a one-man train crew. Trains are centrally dispatched from loading drifts which are interconnected by signal lights, so that when a train in a lateral drift is given permission to move into a main line drift, a red light signals in all other lateral drifts in that area. Good track is maintained, and safety niches are required at all switch throws. Since safety niches were provided there have been no fatal or serious accidents at such points. All main line haulage drifts are illuminated by electric lights. Haulage drifts are kept clean. Adequate clearance has been provided between cars and between cars and the sides of the haulage drifts. The 4 1/2 ton Cranby type cars are equipped with roller bearings, and the 10 ton loconlotives with trolley shoes instead of wheels. These two features are responsible for improved ore haulage conditions and contribute to greater efficiency and safety.

Jan 1, 1950

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Charles Kingsley

THE PRESIDENT (DR. C. B. KINGSTON, member C.l.M.M.) expressed regret that neither of the authors of the paper was able to be present to submit the paper in person. In their absence, it would be introduced formally from the Chair. It was a clear, straightforward account of a fine piece of shaft sinking, cleverly conceived and boldly executed. He referred briefly to the distribution and nature of the Dome ore-bodies and stated that, for both the miner and the metallurgist, the mine had provided a wide range of problems of unusual interest. Discussion on the paper was then invited. MR. THOMAS PRYOR said the paper was most opportune, because the subject of internal shafts did not appear to be fully treated in current mining literature. Many members were not familiar with Canadian gold deposits and it would be of interest if the authors could give a brief description of the location of the ere deposits of the Dome mine. This information would doubtless explain why a new internal shaft was needed in a position which required such an exceptionally long cross-cut to connect it to the main hoisting shaft to surface. It would also add to the value of the paper if the authors would give some idea of the duty expected of the new shaft in terms of tons of rock hoisted and of trips engaged in the transport of men and materials, and it would be helpful if figures could be given of the total capital cost of the hoists and subsidiary excavations at the shaft top, and of the cost per foot for sinking and lining the shaft below the collar. Turning to details of the paper, one was favourably impressed by the care given to the provision of a good travelling way for men in the main cross-cut, as shown in Figure 1. It was by no means always that one could walk in comfort and safety in a working where there was a 20-in. ventilating pipe in the roof.

Jan 1, 1939

By Fei Chen, Lesley J. Gaydos, Laurence M. Demers, Douglas C. Kuhn

The fibrogenic effects of silica in experimental animals and humans has been extensively studied (I 7, 20). However, the pathogenesis and molecular mechanisms underlying lung injury and fibrosis resulting from silica exposure remain to be elucidated. It is well-documented that silica can stimulate monocyte-macrophage lineage cells to produce cytokines and growth factors, including interleukin-I (IL- I) (20), tumor necrosis factor-ex (TNF-cx) (I 7), insulin-like growth factor-I (IGF-1) (4), and transforming growth factor-P (TGF-P) (24). Consequently, it has been suggested that the fibrogenic effect of silica may be mediated by cytokines in the fater stages of silicosis. During the early phase of interaction between silica and the pulmonary alveolar macrophage, several direct and indirect lines of evidence suggest that reactive oxygen intermediates (ROI) may play a pivotal role in silica- induced tissue damage (2I, 22). One of the most important components of and contributors to ROI is nitric oxide (NO) produced from L-arginine and molecular oxygen under the catalytic influence of NO synthase (NOS) (I 9). At present, at least three NOS genes have been cloned: a constitutive neuron NOS, a constitutive endothelial cell NOS and an inducible NOS (iNOS) (16). A number of factors have been shown to differentially induce iNOS gene expression in different cell lines including bacterial cell products and foreign antigens. During inflammation, NO is a double-edged sword in terms of the host immune defense mechanisms and the physiologic response to an inflammatory insult. The macrophage is one of the major cellular sources of NO. During the early phase of acute inflammation, NO produced from the macrophage appears to facilitate the clearance of pathogens and promotes a local relaxation effect on the microcirculation of vascular smooth muscle. When the production of NO is left unattenuated, especially under oxidative stress, direct cytotoxic effects of NO can emerge through the formation of peroxynitrite as a result of a reaction between NO and superoxide (2).

Jan 1, 1998

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be "land poor" but "coastline rich," meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. The Independent State of Papua New Guinea (the State) recognizes this tremendous opportunity and is taking a leadership role in this emerging industry by becoming a 15% partner in Solwara 1 (with an option to increase their investment to 30%).The Solwara 1 Project has been gaining momentum since Nautilus Minerals and the State signed an Agreement on April 24. This new agreement with the State in which they have staked a minimum 15% interest as a meaningful partner, underscores the State’s continued and widespread support for the Project. Signing of this Agreement was a historical occasion and a milestone achievement for Nautilus Minerals and the people of PNG.The machinery being built for the Solwara 1 Project is taking shape. The Seafloor Production Tools are now over 90 percent complete. Assembly of the biggest tool, the Bulk Cutter, was completed in April this year and assembly work on the Collecting Machine and the Auxiliary Cutter commenced in May and June this year respectively. The Riser and Lifting system, which will be used to transfer the mined material from the seafloor to the surface within an enclosed system, is over 50 percent complete. The critical path for the Solwara Project is to secure a suitable vessel arrangement. Nautilus aims to have this completed by the end of this year."

Sep 1, 2014

By H. C. Fuller, J. H. Jacobs

"Manganese ore from Metals Reserve stock piles at Deming, N. Mex., Cushman, Ark., and Philipsburg, Mont., were processed in the Bureau of Mines pilot plant at Boulder City, Nev., to determine their suitability for the production of electrolytic manganese. Manganese was produced successfully from all of the ores.The ores, crushed and ground to minus 33-mesh, were roasted in a Skinner furnace to reduce the manganese and were then leached with spent electrolyte, from the cells, containing sulfuric acid. Acid-leach extractions of 96 percent on Deming, 89 percent on Cushman, and 97.5 percent on Philipsburg ores were obtained. Neutralization of leaches with ammonia results in the highest manganese extraction; but Cushman and Deming leaches could not be neutralized with ammonia, because the amount required was more than enough to maintain the proper ammonium sulfate concentration. A combination of ammonia and calcine was used. However, ammonia was satisfactory for neutralization of Philipsburg leaches. Sulfuric acid needed for make-up was as follows: Deming, 0.380 pound per pound of manganese extracted when neutralized with ammonia and calcine; Cashman, 0.402 pound per pound of manganese extracted when neutralized with ammonia and calcine; Philipsburg, 0.594 round per pound of manganese extracted when neutralized with ammonia alone.All of the leach slurries settled well enough to be separated and washed in countercurrent thickeners.Impurities were precipitated with hydrogen sulfide and removed by filtration. Cushman ore solution contained only- small amounts of impurities and required 0.055 gram of hydrogen sulfide per liter of solution for purification. Deming and Philipsburg solutions contained large amounts of zinc and required 0.55 and 0.65 gram of hydrogen sulfide per liter of solution, respectively.Electrodeposition was satisfactory on all three ores and current efficiencies of 62 to 66 were obtained.A process for the production of electrolytic manganese has been developed by the Bureau of Mines, first on a laboratory scale4/ and then on a semicommercial pilot-plant scale.5/ At first the- pilot plant operated on ore from the Three Kids mine near Las Vegas, Nev., to determine the practical features of the process on ore of this type. Since completing the work on this ore, the pilot plant has been used for processing other domestic ores to obtain engineering data and other economic information regarding the amenability of such ores to the process."

Sep 1, 1946

By J. L. Lytton

The flow-stress recovery of high-purity aluminurn following a 10 pct tensile prestrain was studied in terms of a fractional flow-stress recovery parameter fr. The flow-stress recovery behavior was related to the dislocation arrangements using transmissiort electron rnicvoscopy. During recovery at 120° and 160°C, nearly stable strength levels were attained, the strength level for 120°C recovery being greater than that for 160°C. This stabilization of flow stress was related to the formation of meta-stable dislocation networks bounding nearly perfect cells. Both network formation and the annealing of dislocation loops were found to be recovery mechanisms, and the stronger metastable strength level joy 120°C recovery was related to a smaller average cell size. Analysis of the networks was consistent with the reaction of sets of dislocations with a/2 (110) Burgers vector to give product Burgers DURING isothermal annealing of cold-worked metals, a degree of softening occurs without re-crystallization, and the processes responsible for this change are termed recovery processes. During recovery annealing, the dislocations generated during cold work become rearranged into low-energy configurations, and as much as 50 pct of the stored energy is released."&apos; The relationship between this rearrangement of dislocations and mechanical behavior is of considerable importance, since the dislocation substructures formed during recovery provide a significant degree of low-temperature strength3j4 and can favorably alter the course of primary creep at high temperatures.4 The purpose of the present study was to relate the flow-stress recovery behavior of high-purity aluminum to the substructural modifications that occur. Electron transmission microscopy was therefore employed for direct observation of dislocation substructures at various stages of recovery following 10 pct prestrain. Several investigators5-&apos; have proposed that dislocations can become rearranged or lost during the preparation of thin foils. It was found early in the present study that the dislocation structures in the thicker regions of the foils changed in a systematic way during the course of recovery. Therefore, it is unlikely that substantial losses or rearrangements occurred during thinning. This point will be discussed in more detail later. The results of various investigators indicate that recovery processes in fcc metals can result in release of 50 pct or more of the total energy stored in the as-prestrained metal, this percentage decreasing with increasing prestrain.&apos; Alloying elements or impurities tend to increase this percentage. The release of stored energy of fcc metals during recovery appears to occur by 1) annealing of point defects if the deformation occurred at sufficiently low temperaturesg and 2) rearrangement of dislocations into low-energy Configurations.1,2In bcc metals, the annealing of dislocation loops has also been observed during recovery after prestrain,10-12 and it has been proposed that this is a recovery mechanism for unidirectionally strained fcc metals.&apos; The density of dislocations in bcc metals has not been observed to decrease appreciably during recovery,10 although the formation of regular dislocation networks has been observed. has shown that the formation of such networks can result in elimination of long-range stresses and can lead to significant release of stored energy without dislocation annihilation. It might thus be expected that network formation is a significant recovery mechanism in fcc metals, although extensive network formation has apparently not been reported in controlled recovery experiments. The formation of sub-boundaries in aluminum has been observed by various investigators13&apos;17 during recovery studies of aluminum, but the structure of these boundaries was not resolved. In this regard, it is significant to note that Bailey and Hirsch,&apos; using transmission electron microscopy, detected no network or sub-boundary formation during recovery of 99.99 pct Ag. Furthermore, Clarebrough et al.2 found no such rearrangements during recovery of copper. EXPERIMENTAL PROCEDURE The high-purity aluminum used in this investigation was obtained in the form of 0.125-in.-thick sheet. Spectrographic analysis revealed that the sheet was 99.995 pct A1 with the following weight-percent impurities: 0.001 Cu, 0.002 Fe, 0.001 Si, and 0.0004 Mg. The as-received sheet was in the heavily cold-rolled condition. The as-received sheet was cold-rolled at room temperature to 0.040-in.-thick sheet in the longitudinal direction, which was the original rolling

Jan 1, 1965

By P. Leo

The hot deformation behavior of a Mg-9A1-1Zn alloy produced by high pressure die casting has been investigated by means of compression tests in the temperature and strain rate ranges of 125-300°C and 10-5-10-1 s-1 and torsion tests over 150-450°C and 5, 0.5, 0.05 5-1 . The compression samples were deformed in the die-cast state or after homogenization at 415°C for 2 h to evaluate improvements. A premature fracture at 45° with respect to the compression axis was observed in samples strained at low temperatures and high strain rates. The torsion specimens were tested as received or after a predeformation-homogenization treatment. In addition to constitutive analyses suitable for modeling previously published, the results are fitted to a relationship between strain rate normalized by diffusion coefficient and flow stress normalized by modulus. The results fit well with a set of published creep experiments that were conducted in the range of 70-150°C.

Jan 1, 2006

By Bruce F. Grant

"INTRODUCTION The future of oil production in the part of the Appalachian region included in southwestern Pennsylvania; West Virginia, and southeastern Ohio is directly dependent on the maintenance of existing wells. This report presents an analytical study of the methods used in oil-well reconditioning in this area. The study is part of a research program designed to evaluate those means of stimulating oil production that can effectively and economically maintain present oil-production rates and make it possible to keep existing wells in operation. Well-reconditioning work was curtailed during the war; therefore, an abnormally large number of wells in the Appalachian Region is now in need of repair. Because the lubricant content of Appalachian crude: oils is high and the refined lubricating oils an; particularly suited to use in high speed, high-temperature engines, the demand for these crude oils during the war exceeds, the maximum rate of production obtainable under wartime operating conditions. Increases in operating, expenses, inability to meet war-time reconditioning costs, and inflexible price structures caused the abandonment of an alarming number of wells during the past 4 or 5 years.As a means of increasing regional oil-production rates, new drilling in the older fields for primary production generally is uneconomical because reservoir pressures in most of the fields have virtually been depleted and the production rates of newly drilled wells are small."

Feb 1, 1948

By E. P. Dowding, J. Schlocker, C. H. Fuchsman, R. R. Lloyd, Mahan. W. M., O. C. Garst, W. T. Rawles

"INTRODUCTION The United States, although the leading consumer of chromite, depends almost entirely on imports for its supply. For instance, the consumption during. 1941 amounted to 714,645 long tons, whereas the domestic chromite production, although the highest since 1918, was 12,731 long tons or only 1.78 percent of the domestic consumption. 9/ Domestic production was tremendously, accelerated,after 1941 by war demands; however, only a small proportion of this domestic product was of sufficient quality to be substituted for the high-grade imported chromite demanded for metallurgical purpose. Chromite is used largely for making ferrochromium, an alloy containing 60 to 70 percent chromium which is used in making alloy steels. Peacetime specification for ferrochromium required that it should contain 68 to 69 percent chromium. These specification were lowered to between 60 and 63 percent, chromium in 1941 to permit the use of lower-grade ores. The specifications for metallurgical chromite, used for making ferrochromium, were established first by the Metals Reserve Company at 48 percent Cr203 and a Cr. Fe. ratio of 3 : 1 but later were lowered to 45 percent Cr203 and a Cr : Fe ratio of 2.5 : 1. The ratio of chromium to iron in chromite is important, because the contained iron enters the alloy in making ferrochromium and, although an ore may contain the required 45 percent Cr203, it may contain too much to be suitable for ferrochromium production. The principal sources of domestic chromite are California, Oregon, Montana, and Alaska minor, small, and widely scattered deposits in another dozen States. Without exception, these deposits are low-grade, require beneficiation to produce a commercial product, and are not competitive with imported high-grade ore in normal times. Nevertheless, these deposits form strategic reserve, which must be utilized in periods of national emergency. Recognizing this fact; the Bureau of Mines for many years has undertaken investigations to develop methods of utilizing domestic chromite ores. The problem has been approached from three angles: (1) Mechanical methods of concentration; (2) beneficiation by chemical or metal¬lurgical methods; and (3) production of metallic chromium by electrolysis of solutions prepared from ore or concentrate."

Feb 1, 1946

R. W. Raymond, New York, N. Y,:—Since the presentation of my note on this subject at the New York Meeting, Professor Louis has pointed out an error in my statement of his conception of " pitch "—namely, he understands the pitch, in the restricted sense which he proposes, to be the angle of inclination of the axis of an ore-body, measured on the vertical plane drawn through the body; whereas, I represented him as proposing to define " pitch " as the angle of inclination of an oblique body, measured on the plane of the dip, in the direction of the strike. The difference will appear upon consideration of the accompanying isometric projection, Fig. 1, in which ABCD represents the plane of the inclosing ore-deposit (vein or bed), and AC the axis of the oblique ore-shoot. ABE is the angle of the dip, as universally understood; and ACE

Jan 1, 1909

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By David E. Siskind

A Bureau of Mines survey of noise from quarry production blasting was conducted at seven crushed-stone quarries, providing information on close-in noise generation, comparative instrumentation, and evaluation of the sound levels as related to blasting parameters and existing State and local noise standards. The results from this preliminary survey will be useful in the design of a complete investigation of the problem of noise from blasting. There exists an immediate need for technical guidelines for noise pollution control agencies presently working on the regulation of impulsive noise sources. This survey and results from previous work by other researchers are used to derive interim recommendations on weighting scales, generated sound levels, and instrumentation. These recommendations are based on the limited data presently available and may be modified with subsequent investigation of noise generation, propagation, structural damage, and human tolerance.

Jan 1, 1974

By Margaret E. Harris

The formation of nitrogen oxides, the decay of carbon monoxide, and the concentrations of residual hydrocarbons in the secondary combustion zones of propane-air and methane-air flames were studied in three enclosed burners designed to simulate gas appliances such as space and water heaters. The effect of thermally or chemically perturbing the combustion gases above these flames was determined theoretically and by means of factorial experiments. The concentrations of air pollutants and the flame temperatures were measured, and the effects of ingress of secondary air into the primary and secondary combustion zones, flame stability, burner port surface, and simulated recycling of combustion gases were noted. Based on this study, four principles were derived that, applied to gas appliance design, will insure minimal emissions of these air pollutants: 1. Oxides of nitrogen can best be kept low by depressing peak temperatures to about 3,050° F. 2. If this is not possible, then the secondary combustion zone should be cooled rapidly to this temperature. 3. Carbon monoxide concentrations can be limited by rapid induction of secondary air. 4. Hydrocarbon concentrations can be controlled by designing for well-seated, stable flames. In addition, empirical reaction rates were derived that predict the concentrations of nitrogen oxides and carbon monoxide in the primary and secondary combustion zones.

Jan 1, 1970

By Dean H. Ambrose

[Mining and processing earth&apos;s materials form the basic building blocks from which many technology advancements and products are made. Virtually all metallic and non- metallic products are derived from a substance found in our earth that we blend, mold, extrude, or pulverize into something useful, the mining industry is responsible for the first step of this process: extraction from the ground. Mining particularly coal mining. poses significant risks to both humans and machines. As raw materials are]

Jan 1, 2009

By E. G. Noble

The effects of hydrogen chloride (HCI) concentration and temperature on the solubility and hydration state of the alkali chlorides LiCI, NaCI, and KCI and the alkaline-earth chlorides, MgCI2, and CaCl2 were investigated by the Bureau of Mines. Saturated aqueous solutions of the chlorides were sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increased HCI concentration caused decreased salt solubility be-cause of the common ion effect. Aqueous solubilities for the chlorides of Ca, Li, Mg, K, and Na ranged from 42.6, 45.2, 35.2, 25.5, and 26.1 pct, respectively, at 20° C to 56.9, 49.4, 37.6, 31.0, and 27.0 pct, re-spectively, at 60° C. In solutions sparged to HCI saturation, solubili-ties for these chlorides ranged from 22.4, 26.5, 3.0, 1.3, and 0.05 pct, respectively, at 20° C to 53.2, 48.8, 28.3, 2.6, and 0.8 pct, respec-tively, at 60° C. The solubilities of LiCI and CaCl2 in HCI solution were high because HCI solubility is low in these solutions. The chlo-ride salts of Ca, Li, and Mg formed hydrates, which depended on tempera-ture and HCI concentration. Monohydrates for LiCI, tetrahydrates and hexahydrates for MgCI2, and dihydrates, tetrahydrates, and hexahydrates for CaCl2 were obtained.

Jan 1, 1985

By E. M. Stiles

THE Wellington Lake power plant of the Consolidated Mining and Smelting Company of Canada, Limited, about 25 miles from Goldfields, Saskatchewan, is the second hydro-electric project operating in that Province, the first being the Island Falls plant of the Churchill River Power Company which serves the operations of the Hudson Bay Mining and Smelting Company at Flin Flon, Manitoba. The Churchill River project develops 90,000 h.p. at 56-ft. head; the Wellington Lake plant 3,300 h.p. at 75-ft. with pro-vision for an additional 3,300 h.p. unit. Churchill River power is trans-mitted at 110,000 volts over a 58-mile line of steel towers to Flin Flon and an additional 45 miles over a wooden pole-line to Sherritt-Gordon. Our steel tower-line is 22 miles long, and the voltage is 60,000; this choice be-cause certain such equipment was available from Trail. The diversion of 15,000? second-feet at 56-ft. head for 90,000 h. p. at Churchill river dwarfs our 500 second-feet flow at 75-ft. head for 3,300 h.p. In both cases, the main obstacles to be overcome during plant construction were the lack of transport facilities and the short open season. Let it be noted here that this paper deals mainly with those phases of plant construction which were particularly interesting to the writer. With-out these variations from the ordinary routine, this is just another power project whose story is better told by the accompanying charts and pictures. To many members of the Institute it is still just that; but I am writing for those who, like myself, have been too seldom responsible for major under-rakings at an appreciable distance from a railway siding. When it was planned in early 1937 to erect a 1,000-ton mill at our Box mine, both hydro and Diesel power were discussed. With ten years&apos; ore in sight, even an expensive hydro project, such as ours turned out to be, produces kilowatts materially below the 2-cent operating cost of a Diesel plant using fuel-oil at 14 cents a gallon.

Jan 1, 1940

By Roxana Barrantes Huamán

El presente texto describe la geología económica del depósito aurífero Alpacay ubicado en Arequipa, Perú. El depósito Alpacay es un típico depósito mesotermal, filoniano que es explotado por la Cía Minera Yanaquihua, donde el mineral es procesado en una planta de cianuración, gravimetría y flotación. Costa. Asímismo, se realiza en la Franja Aurífera Nazca-Ocoña que alberga innumerables minas y depósitos en vetas angostas como Arirahua, San Juan de Chorunga, Chalhuane, Las Clavelinas, María Eugenia, entre otros. La alteración es básicamente argílica en la vecindad de las vetas y propilítica hacia el exterior.

Sep 12, 2011