Search Documents

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By AUGUSTUS J. MONKS, Norman L. Weiss

THE Santa Barbara Unit of the Compania Minera Asarco, of which the San Diego mill is a part, is in the Parral District of southern Chihuahua. Although the concentration of sulfide ores has been practised in Santa Barbara since 1900, the San Diego mill, completed in 1921, was the first plant in northern Mexico to attempt the treatment of oxidized lead ores. From the milling point of view the many ores that have been treated at San Diego are very similar, the differences among them being rather of degree than type. Since 1921 the number of ores from different sources treated simultaneously has varied from four to eleven; in no case have any distinctive characteristics warranted the separate treatment of any of these. The zone of oxidation, source of the ores milled at San Diego, extends to a depth of 300 to 400 ft. below the surface. These ores carry more gold and less silver, lead, copper, and zinc than the underlying sulfide ores; the gangue minerals appear comparatively unchanged by oxidation and leaching. Lead occurs in diverse minerals, chiefly in cerussite, galena, and angle-site, the proportion of the lead in galena varying considerably in the different mines. An average of the feed to the mill would show the following approximate distribution of the lead content:

Jan 1, 1930

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972

By M. Muinonen, R. Pandher

Royal Nickel Corporation is developing the Dumont Nickel Project, a large nickel sulphide deposit located near the town of Amos, Québec. The nickel occurs as pentlandite, heazlewoodite, and awaruite. The relatively low grade ore can be processed to a very high grade nickel concentrate, containing 29% Ni. The absence of copper and precious metals in the ore renders this concentrate amenable to processing by dead roasting in a fluid-bed roaster and smelting in an electric furnace to produce ferronickel for sale to stainless steel producers. Laboratory test work and conceptual engineering design was completed to demonstrate the amenability of Dumont concentrate to produce ferro-nickel.

Jan 1, 2015

By Keith A. Heasley, Timotlly M. Barton

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence- Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents a case study where a mechanics-based, boundary-element program is used to calculate the surface subsidence associated with several panels of a Northern Appalachian longwall coal mine. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin seam or vein type deposits. In this paper. the program is used to calculate both the underground convergence and the resulting surface subsidence at three longwalls. The subsidence results from the model are compared with field measurements and analyzed The results from the case study in this paper demonstrate that the laminated model with calibrated properties can easily provide fairly accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies are recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

By AIME AIME

MANY interesting papers, opportunity of seeing o1d friends, and an exposition showing all that is latest in equipment, all were factors in bringing a large crowd to Detroit during "Metal Week," October 2-6. The Institute's Iron and Steel and Institute of Metals Divisions held technical sessions at the Statler Hotel on October 4 and 5, and that hotel was also headquarters for the American Society for Steel Treating and the American Society of Mechanical Engineers, both of which also had technical sessions. The American Welding Society and the Wire Association met at the Book-Cadillac Hotel, and the exposition was staged at Convention Hall, out Woodward Avenue. All in all it was a big week for men interested in metal working. One of them stated to your reporter on the train en route to Detroit that this was the one convention that he never missed, and doubtless others felt the same way about it.

Jan 1, 1933

By K. L. Paciorek

The aim of this program was to develop a reliable and meaning-ful basis for assessing certain safety aspects, namely fire and, in particular, toxicity hazards of articles employed in underground coal mining operations. The present investigation was concentrated on the thermal oxidative degradation of representative hydraulic fluids. To achieve this goal all products formed on thermal oxidative degradation of the fluids studied were analyzed, identified I and the amount of each individual species present was determined quantitatively on a weight of product per weight of material basis. The weight/weight data thus obtained can then be factorized to reflect the relative toxicity of each individual species present, using for example the Threshold Limit Values adopted by the American Conference of Governmental and Industrial Hygienists, whereby an overall "toxicity index" can be arrived at which makes it possible to compare the different fluids and/or classes of fluids in a quantitative manner insofar as their toxicity is concerned.

Jan 1, 1976

By M. A. Elliott, H. H. Schrenk, L. G. Berger, John C. Holtz

"INTRODUCTION Interest in the possibility of using Diesel 6/ engines for haulage power in mining and tunneling is increasing in the United States, owing largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.Proponents of the application of the Diesel engine to underground haulage base their claims for its safety upon a comparison with the gasoline engine, assuming that (1) the carbon monoxide content of Diesel exhaust gas is always low and that (2) fire and explosion hazards from Diesel fuel are minimized because of its low volatility. In these respects the Diesel engine appears less hazardous than the gasoline engine, whose use underground has been discouraged by the Bureau of Mines and other organizations interested in safety in mining. However, such generalizations cannot be accepted as conclusive evidence that safety is inherent in Diesel engines in underground service, as European experience indicates that certain hazards may accompany their use. Such hazards were discussed in a previous publication 7/ that reviews developments in the use of Diesel locomotives in European coal mines.The Bureau of Mines has initiated a study of the hazards that may attend the use of Diesel engines underground to obtain first-hand information that may serve as a basis for recommending sale practices under conditions existing in the United States."

May 1, 1940

By S. J. Cohen

Changes in our energy, national security, and commerce needs have necessitated identification of new sources of minerals, such as rare earths, lithium, copper, silver, aluminum, titanium, and the minerals on the U.S. Geological Survey’s (USGS) list of critical minerals (USGS, 2022). With the need to domestically produce these minerals, more mining will be required within the U.S. Some of these critical minerals deposit with naturally occurring radioactive materials (NORM), therefore, mining these minerals may concentrate NORM to the point that some states may require licensing and radiation protection programs. NORM is not regulated by the Federal government; it is regulated by the individual states. Consequently, overall national state of NORM regulation is chaotic with each individual state either choosing to regulate or not regulate NORM, and, if a state chooses to regulate NORM, then that state develops its own unique regulations. Further complicating the regulatory environment, states utilize a wide variety of strategies for regulating NORM, which sometimes results in inappropriate regulations, inconsistencies with specific radionuclides that are regulated, and inconsistencies with specific NORM types that are regulated. This paper will review the nature of NORM regulations, identify regulatory traps, and provide general guidance for identifying NORM and potentially avoiding regulatory jeopardy. Because of the chaotic nature of NORM regulations nationally, seeking guidance from qualified professionals with relevant expertise is recommended. Also, contacting the appropriate regulatory agency to gain a complete understanding of the NORM regulatory environment is useful for maintaining compliance.

Feb 1, 2023

By O. K. Olawale, G. O. Edaogbogun, B. N. Ben‑Festus, F. Ben, F. R. Amodu

The environmental and health implications of artisanal gold mining activities at mining sites across Nigeria have rekindled research interest. This study aimed to assess the scalability of naturally occurring radioactive materials in gold mining sites in Iperindo, Nigeria. Soil samples were collected from three different mining sites and control locations and analyzed for natural radionuclides, mainly 238U, 232Th, and 40K, using gamma spectrometry having a sodium iodide detector. The average activity concentration values of 61.55 ± 3.71, 72.65 ± 4.45, and 1134.99 ± 38.12 Bqkg− 1 obtained from within the mining sites for 238U, 232Th, and 40K, respectively, were above the world permissible values of 33.0 Bqkg− 1 for 238U, 45.0 Bqkg− 1 for 232Th, and 420.0 Bqkg− 1 for 40K. The average activity concentration values of 15.26 ± 3.19, 21.46 ± 4.27, 381.04 ± 23.36 Bqkg− 1 estimated for 238U, 232Th, and 40K, respectively, for the control location were, however, lower than the global permissible values. The study also evaluated other radiological parameters such as radium equivalent, dose rate, annual effective dose rate, internal and external hazard indices, and alpha and gamma indices. The obtained values were 252.83 Bqkg− 1, 119.98 nGyh− 1, 147.15 mSvy− 1, 0.85 Bqkg− 1, 0.68 Bqkg− 1, 0.31 Bqkg− 1, and 1.89 Bqkg− 1 respectively. Except for radium equivalent, external and internal hazard risks, and alpha index, which were significantly lower than the recommended threshold, all other radiological parameters were higher than the recommended global limits. Moderate data reproducibility and a p-value of 0.000574 further reinforced the robustness and reliability of the results obtained in this study.

Feb 22, 2024

By W. Banda

"Trial application of air decks on a production shot improved fragmentation (32% reduction in x50). Empirical fragmentation models and digital image processing software were used to estimate fragment size distribution of the blasted muck pile. The x20, x50, and x80 passing fractions, and top size were 42, 265, 683, and 1,455 mm, respectively. Air-deck application reduced explosives load in blastholes, lowering total charging cost by US$20/hole (15% decrease) and the powder factor to an average of 0.86 kg/m3 (12% decrease). Blast results were 443,624 t of blasted material from the block (90% of total muck pile) was smaller than 900 mm.RÉSUMÉ L’application pilote de trous d’air dans le cadre du coup de mine effectué pour commencer la production a amélioré la fragmentation (une réduction de 32 % des x50). Des modèles empiriques de fragmentation et un logiciel de traitement numérique des images ont permis d’estimer la composition granulométrique des fragments du tas de déblais abattus. Les fractions de passé de crible de x20, x50, x80 et la dimension supérieure étaient représentées par des dimensions respectives de 42, 265, 683 et 1 455 mm. L’application de trous d’air a permis de diminuer la charge d’explosifs nécessaires dans les trous de mine, réduisant ainsi les coûts totaux de chargement de 20 $ US/trou (soit une réduction de 15 %) ainsi que le facteur de chargement (facteur poudre) à une moyenne de 0,86 kg/m3 (soit une réduction de 12 %). Les coups de mine ont résulté en 443 624 tonnes de matériaux abattus du bloc (soit 90 % du tas de remblais total) mesurant moins de 900 mm. INTRODUCTIONThe main objectives of production blasting are to achieve optimum rock fragmentation and to minimize overall production costs. Because blast fragmentation significantly affects the profitability of a mine, blasting is the first step of the size reduction in mining: An optimum size distribution is required to maximize the performance of mining and subsequent milling processes. If the fragmentation size distribution can be modelled and controlled, operations performance will improve. Blast fragmentation modelling is important in mineto- mill optimization: It allows the estimation of blast fragmentation distributions that can be modelled in downstream mining processes to determine the optimum blast design."

Jan 1, 2018

By Theodore H. Boggs

The battle of the gold standard is not limited to one country alone, or even to a single group of countries. It is being waged merrily in many important commercial and industrial quarters. Though it is not always a practical issue calling for immediate attention, it is none the less, quite widely, engaging the thought of bankers and other students of finance. The controversy arises, in the last analysis, because of the desire of men to secure a stable currency. There are two ways of restoring a reasonably stable currency system: (1) the re-establishment of the gold standard, or (2) the deliberate and artificial management of a paper currency. Both systems are well known. The gold standard was in use prior to the war in the principal commercial countries. A currency of inconvertible paper has been at times employed in the past in various countries; for example in Britain from 1797 to 1821, and in the United States from 1862 to 1879. The gold standard, as all are aware, implies the selection of gold as the standard of value. The unit of value is a fixed weight of gold and, so long as the standard remains unimpaired, all other means of payment are maintained at a parity with standard gold coins. And gold coins alone constitute the standard money, inasmuch as their value as bullion equals their value as coins. Under the gold standard this would not be true of any other form of money, although all other varieties of money, including bank notes, government notes and silver coins would be freely convertible into gold money. Strictly speaking, the gold standard also implies that the gold money in turn shall itself be freely convertible, through melting, into gold bullion and freely exportable.

Jan 1, 1925

By S H. Son, M K. Wang, H K. Jeong, B K. Cho, J I. Park

The utilisation of low-grade raw materials such as fine iron ore and semi-soft coking coal, and reduction of CO2 emissions are important issues in the ironmaking process. To solve these issues, a new process called PosPRA (POSCO prereduced agglomeration process) has been developing at POSCO. It focuses on the reduction of carbon composite iron ore briquette in travelling grate. In this study, the possibility of manufacturing the prereduced agglomerate (PRA) under oxidising atmosphere with travelling grate and the optimum manufacturing conditions of carbon composite iron ore briquette are investigated. The results have shown that controlling the temperature and oxygen potential in the range from 1100 to 1200°C and below 10 vol per cent respectively is very important to increase the reduction efficiency of briquette in travelling grate. High quality properties of the green briquette and PRA could be manufactured by using the briquette mixed with 20 wt per cent of coal under 0.1 mm in size under compacting pressure in the range from 3 to 7 t/cm. Adding 1 wt per cent water as a binder is proper under the condition of high compacting pressure. In a pot grate test, the compressive strength and metallisation degree of PRA are achieved over 150 kgf/p and about 55 per cent respectively, at bed temperature 1150°C and oxygen potential of 10 vol per cent when 20 wt per cent of coal is mixed in the briquette.CITATION:Wang, M K, Son, S H, Park, J I, Jeong, H K and Cho, B K, 2017. Development of prereduced agglomeration process using carbon composite iron ore briquette in travelling grate, in Proceedings Iron Ore 2017, pp 111–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By R. H. Fett

T HE APPROACH to maintenance must always be ?completely positive: there must be no question of putting off difficult problems until it is more convenient to tackle them. By this it is meant that a piece of machinery or equipment which, by experience, is known to be due for a check should not, merely because it appears to be operating satisfactorily, be left until it reaches a critical .condition and breaks down. The mentality of the Maintenance Manager must be completely orderly and methodical and he should, in fact, possess a ledger-book mind, having a debit and credit outlook. The debit side would be that applying to time out of service, cost in wages, material, personnel involved, etc., and the credit side that relating to continuous operational time of the locomotive and therefore to the ultimate benefit of the mine and the personnel who work there. The Maintenance Manager is not concerned with design problems, and although he and the personnel under his jurisdiction are not engaged in productive work, he and his staff do, nevertheless, add greatly to or detract from the overall efficiency of the organization. Provided the machinery placed in his care is good to start with, he must take the best steps he possibly can to keep it running. However, he may, on occasion, be forced to improvise and this is where the ingenuity of a clever man rises to the occasion.

Jan 1, 1956

By S Harris, A Bossilkov

The Kwinana (Western Australia) and Gladstone (Queensland) industrial areas are among the few dozens of heavy industrial areas globally that demonstrate significant levels of regional resource synergies. Such synergies are also referred to as æindustrial ecologyÆ or æindustrial symbiosisÆ. Fundamentally they involve the exchange of by-products or sharing of utilities between companies in close geographic proximity to achieve competitive advantage and environmental benefit. A concerted research effort is currently underway to foster greater realisation of regional resource synergies in minerals processing intensive regions, in Australia and internationally. This paper summarises current insights from the foundation research into engineering tools and technologies and enabling mechanisms for regional resource synergy developments. Regional resource synergy developments were reviewed for 16 international and two Australian regions. It was found that Kwinana and Gladstone compare favourably with the well-regarded international examples of regional synergy development. Given the fairly strong evidence that self-organisation is critical for regional synergy developments, an implementation model has been proposed that captures entry points for synergy developments at the level of platform (industry collaboration), process (developing synergy opportunities) and project (assessing and implementing specific synergies). It was also found that regional synergies have so far developed in the absence of specific methods for identification and screening of synergy opportunities. Moreover, very limited attention has been paid to the associated technological and engineering challenges. The current technical research effort therefore targets: the development of a toolset for the identification and development of potential synergy opportunities; and assessment of technology needs and opportunities for regional synergies involving water, energy and materials recovery and reuse.

Jan 1, 2006

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By William M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Ropes of sizes ranging from 3/4 to 2 in. in diameter and from 2 to 35 ft in length were tested to determine their breaking strength, elongation, and torque. This was done to characterize the test equipment on ropes used in mine hoisting systems.

Jan 1, 1990

By John E. Kelley

The Bureau of Mines conducted a study to determine the feasibility of joining refractory metal compounds to each other and to oxide ceramics by a vacuum hot press-diffusion bonding method. Very satisfactory joins were made of ZrC to ZrB2, ZrN to ZrB2, ZrC to ZrN, and of ZrC, ZrN, and ZrB2 to Al203. Each of these join assemblies contained a mixture layer comprising 50 weight-percent each of the two end compounds. The mixture layer, sandwiched between each end compound, enhanced bonding and smoothed out the thermal expansion gradient between the two end members. Strength and thermal shock tests showed that the join areas of the ZrC, ZrN, and ZrB2 joins were stronger and more shock resistant than the parent materials. Also included in the joining tests was one each of TiC to TiB2, TiC to TiN, TiB2 to TIN, and TiC to ZrB2 joins. Each of these was well bonded, showing that the vacuum-hot-press method can be used for a variety of systems.

Jan 1, 1969

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963