Search Documents

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By P González, J Videla, E Córdova, I Gottreux

Currently, underground mining of deeper massive deposits with lower grades, harder rock conditions in high strength environments, entails difficulties in caving, fragmentation and seismicity of the orebody.So far, the use of preconditioning (PC) with hydraulic fracturing (HF) has shown positive results in terms of seismic response and caving performance, while PC combined with explosives aims to weaken the rock mass, causing an additional effect on fragmentation.In particular, mines commonly referred to as ‘supercaves’, operated by caving methods, have the need to integrate mine to plant processes, where rock fragmentation appears as a key tool. In fact, it implies making mining and comminution processes more efficient to the plant and for mines, it justifies the search of innovative solutions in drilling and blasting techniques to precondition the rock mass. The following paper aims to show the feasibility of numerical blast modelling to weaken the rock mass using explosives, mainly through sensitivity analysis applied to designs to minimise bias and uncertainty in the results. It is shown how the presence of structures, their geometry and in situ stresses influence or interfere with the PC method being used.From the work, it is concluded that better knowledge on the application of explosives weakening allows specialists to strengthen numerical models associated with every design and therefore previously validate their applicability, helping to understand complex phenomena such as the propagation of mechanical waves in non-elastic heterogeneous media. In this sense, it is understood that while there are studies (Sanchidrián, Segarra and López, 2006) showing that the transfer of energy in the rock mass could be even greater in a confined environment, the more competent rock mass and higher in situ stresses interfere mostly on the effectiveness of a technique using explosives.CITATION:Gottreux, I, Córdova, E, González, P and Videla, J, 2016. Preconditioning modelling and explosives effectiveness in block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 683–688 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By LUIS ALBERTO TORRES-CRUZ

The assessment of liquefaction vulnerability is crucial to understanding the potential consequences of a tailings dam failure. The “Plewes method” is a relatively well-known and simple screening method to assess liquefaction potential based on results of cone penetration testing (CPT) which may be complemented with laboratory testing. The objective of the current work is to emphasise the screening nature of the method and its uncertainties when applied in tailings deposits. Specifically, the paper highlights the difficulties in assessing the intrinsic uncertainty of the method and the additional uncertainty that results from variations of the slope of the critical state line (λ10) along the depth of the CPT sounding. The results of the method are too uncertain for detailed characterisation of tailings even when a relatively low intrinsic uncertainty is assumed. However, the method characterises weaker soils with lower uncertainty (although still too high for detailed characterisation) than stronger soils. The uncertainty of the method is negatively affected by the relatively low λ10 values that are typical of nonplastic tailings. It is suggested that the results of the method should be presented in scatter plots in which the spread of the data is consistent with the uncertainty of the method.

Jan 28, 2021

By M Korte, J McMaster, C Brent

The Barrick Osborne concentrator has gone through a number of upgrades since commissioning and has increased production from the original 119 t/h design capacity to a milling throughput of 265 t/h in 2008. This was achieved incrementally over several years, by maximising operating efficiencies, in order to minimise capital expenditure, and take advantages of economies of scale; but more importantly it was reached with no measurable loss of recovery. Osborne currently processes a blend of underground and open pit material from the nearby Trekelano deposit. Following primary/secondary crushing, the material is processed through a rod/ball mill grinding circuit ahead of rougher/scavenger flotation that produces a copper concentrate. Osborne was seeking a further increase in plant throughput of the order of 15 per cent, but at more sustainable levels of secondary crusher plant utilisation. In early 2008, Osborne contracted Metso Process Technology and Innovation (PTI) to review the entire process from run-of-mine feed to final copper concentrate. This review would be done concurrently with surveys of both the crushing/grinding and flotation circuits being performed at the same time. The outcome would be a steady-state model of the complete flow sheet allowing the crushing/grinding model to interact with the flotation circuit model, such that overall process optimisation was possible. This was to apply both by exploring the operating limits of the currently installed plant, as well as looking at the logical next stage of capital plant expansions. Surveys of the crushing and grinding circuits were conducted at the Osborne concentrator in May 2008. The main objective of the surveys was to review the potential of increasing grinding throughput whilst maintaining the flotation feed 80 per cent passing size. This would also require improving the efficiency of the crushing circuit which was already operating in excess of 80 per cent of the time. Steady-state simulations were performed using the developed circuit models to identify opportunities to increase throughput and alleviate high circulating loads in both the secondary crushing and grinding circuits. Due to operational changes, the recommendations resulting from this project were considered by Osborne but have as yet only been partially implemented.  This paper covers part A or the crushing and grinding component of the project. A separate paper discussing part B or flotation is also being presented at this conference. The results of interactive simulations between the flotation and grinding circuit models are included in part B of this paper.

Jan 1, 2009

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

By M. J. Kovalik

The effect of oxidation by air at temperatures ranging from 200° to 390° C on the change of chemical and physical properties of Pittsburgh-bed coal was studied as a function of processing time and temperature. The goal was to prepare a nonagglomerating fuel from a strongly coking coal for use in continuous carbonizing processes and in fixed-bed gasifiers. The oxidized coal was carbonized in a bench-scale apparatus, and the coke strength was evaluated in a Roga tumbler. Strength of the coke was progressively reduced with time of oxidation until the coking power of the coal was apparently destroyed. Time requirements to obtain an essentially nonagglomerating product were inversely related to processing temperature. Gaseous products released from the coal during oxidation reduced the yield of the desired nonagglomerating product, which decreased with time of oxidation at constant temperature and with increase in processing temperature at equal time. Oxidation at a temperature slightly above the lower limit of the plastic temperature range of Pittsburgh-bed coal was most effective because of the short processing time required and moderate processing losses.

Jan 1, 1963

By Frederick Bloetscher

An improved parachute-type stopping for changing the course of mine ventilation air during mine emergencies has been developed by Goodyear Aerospace Corporation for The Bureau of Mines. The stopping can be quickly deployed by one man from a single attachment point and provides excellent stopping performance with the flow in the design direction. Adding pin and foam attachments between its skirt and the passage-way surfaces improves its performance with flow in the design direction and maintains the stopping with zero or reverse air flows. Stopping performance results for a range of airway sizes including 7.5 X 10 ft simulated airway with pressure differentials of up to 3.0 inches of water are presented. Predicted performance values for this stopping design for larger passageways are also presented.

Jan 1, 1977

By F. C. Noyes

DAME Nature was in a generous mood when she distributed widely over the face of the globe numerous deposits of phosphate rock from which man can make phosphatic festiIizer to replace the phosphate re- moved from the soil by crops. The principal deposits are readily accessible to the world's greatest consuming areas and most of them are such that mining operations can be carried on at relatively low cost. The world's known reserves shown in Table 1 are sufficient to last well over 2000 gears at the present rate of consumption. Before giving a brief outline of the phosphate rock industry of foreign countries let us try to get a picture of the movement of phosphate rock throughout the world in 1938, the last full normal calendar year where it came from and where it was consumed. Table 2 shows the origin and finial destination of world shipments in 1938 by grand divisions. Table 3 (p. 499) shows shipment9 of phosphte rock to each country in Europe. Europe is seen to be by far the world's greatest market and the French North African mines the world's most important producers outside of the U. S. A.

Jan 1, 1944

By Suzanne R. Hess-Brittelle, Sharon L. Schulz, Tyler J. Quick, Amy F. Ebnet

"Abiquiu Dam is a rolled earth fill dam with impermeable core located on the Rio Chama in New Mexico. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. During the 1960’s and 1970’s, the grout curtain was extended 1,000 ft. into both abutments and sections of the foundation beneath the embankment were regrouted. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during multiple phases of supplementary grouting and during verification drilling following the 1970’s grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. The fluid losses in the embankment may be related to seasonal shutdown layers in the embankment or benches in the abutment foundations. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment.INTRODUCTIONAbiquiu Dam is located on the Rio Chama in New Mexico and consists of a rolled earth fill dam with impermeable core, controlled outlet works, and an uncontrolled rock-cut spillway. The dam was authorized for flood control and sediment retention and was designed as a dry dam, holding flood pools for relatively short durations. The foundation is comprised of Permian and Triassic age, interbedded mudstones and sandstones that were deposited in an active braided stream system. Sandstones are moderately fractured and have variable aperture and infilling. Generally speaking, joints are near vertical. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. In 1966-1968, the grout curtain was extended 500-ft into the left abutment and the foundation beneath a 560 ft. section of the embankment was re-grouted. In 1978-1980, the grout curtain was extended 1,000 ft. into the right abutment, an additional 500 ft into the left abutment and the foundation beneath the right 520-ft section of the embankment was re-grouted. The alignments of these grout programs are shown in Figure 1. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during both phases of supplementary grouting and during verification drilling following the 1978-80 grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment. This paper provides a summary of the drilling and grouting methods used during these programs and the potential for damage to the embankment."

Jan 1, 2016

By Vernon C. Davis

"SUMMARY AND CONCLUSIONSIn initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining.The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost.This report is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges.Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage.In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested.Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes.Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows parallel to one of the series of joint planes.Methods of detonation made little difference in breakage; but the millidelay caps produced the best conditions for moving the broken rocks."

Jun 1, 1953

By Ryan L. Veenstra

This paper presents a modelling study of a cemented paste backfill in an underground stope. The model was developed to help provide a better understanding of what is happening in the stope during the filling stage of the stope. In order to do this, the model incorporates the paste rise rate, stope geometry, and time-dependent input parameters. This paper looks at the effect of geometry in two parts. The first part compares a series of simple rectangular stope models. These models differ in size both in two and three dimensions. The second part compares the results of four 2D models together and then to the field instrumentation data. Part of this section introduces the geometry and instrumentation within the test stope.

Jun 1, 2012

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By G. W. H. Norman

"The La Corne molybdenite-bearing veins, discovered in 1915, lie halfway between Amos and Val d'Or near the southwest corner of La Corne township, Abitibi county, Quebec. The Molybdenite Reduction Company, which carried on operations during 1927 to 1930, sank a 200-foot inclined shaft to develop the property and produced about 22 tons of concentrntes from a 30-ton mill during 1929. Hollinger Consolidated Gold Mines, Limited, carried on further underground exploration in 1930. The Molybdenite Corporation of Canada drilled a part of the property in 1938 to 1939 and produced 1 ton of concentrates in 1938. Wartime Metals operated the property from 1942 to July 15, 1945. At this time the mill was enlarged to treat 200 tons daily. Molybdenite Corporation of Canada since July 15th, 1945, have continued the operation of this property and have revised the mill flow-sheet in order to produce both a bismuth and a molybdenite concentrate.The production for the period 1942-1946 is as follows:Total molybdenite production from the mine in the 1942 to 1946 period was about 4,127,400 lb.The La Corne deposit occurs at the northwest contact of a small mass of biotite granite with biotite schist. The form and extent of the biotite granite mass is concealed by a wide sand plain that extends northwest and west from the deposit and overlies bed-rock except in four small outcrop areas. These are spaced 1,000 and 2,000 feet apart along a narrow strip extending 5,000 feet south from the mine. The outcrops suggest that the granite must be at least 1,500 feet wide and 3,000 feet long northeastward. Where exposed in the mine workings the contact dips 70°N.W., but is not a sharply defineable feature due to the presence of numerous granite dykes and tongues in a zone of biotite schist 100 feet wide along the margin of the granite. The biotite schist in the few outcrops that flank the north and south sides of the granite strikes northeast and dips 60° to 70° S.E."

Jan 1, 1954

By H. M. Thorne

The Union of South Africa has been interested in oil shale for a long time, and deposits of oil shales, torbanites, and similar rocks have been found in many parts of the country. (Fig. 1.) Samples differ markedly in oil yield and in the characteristics of the oil. The strata vary in thickness, and most of the deposits that have been found are in unfavorable locations because of remoteness from markets or absence of transportation facilities. This report deals mainly with the torbanite deposit near Ermelo, Transvaal, in the Union of South Africa, and the operations of the South African Torbanite Mining and Refining Co., Ltd. (hereafter referred to as Satmar), in mining the torbanite, retorting it, and refining the crude oil.

Jan 1, 1954

The principal activities of the Bureau of Mines Explosives Research Center (now Safety Research Center) during fiscal year 1968 (July 1, 1967, to June 30, 1968) are reviewed in part 1. Part 2 presents short abstracts of the publications issued during this period in the Bureau series and in other media. Part 3 describes a short study on the thermal decomposition of RDX and HMX not destined for publication elsewhere. ACKNOWLEDGMENTS The Bureau gratefully acknowledges the support received through cooperative agreement in fiscal year 1968 from The Manufacturing Chemists Association.

Jan 1, 1970

By Fábio de Oliveira Braga

A descoberta de óleo e gás no Pré-Sal transformou o Brasil em um dos grandes possuidores de reservas de petróleo no mundo e aumentou as expectativas de produção em águas profundas. Apesar da euforia, alguns desafios têm o potencial de inviabilizar a exploração do Pré-Sal: a complexa logística offshore, as dificuldades de acesso ao reservatório, as condições físico-químicas do poço e de subsuperfície. As condições impostas pelo ambiente são relevantes, devido aos altos teores de contaminantes, alta temperatura e pressão, que exigem materiais de alto desempenho. O objetivo deste trabalho é revisar os avanços que podem contribuir para superar as condições físico-químicas do Pré-Sal. Verificou-se que a solução deste problema pode envolver três tipos de abordagem: O desenvolvimento de ligas resistentes à corrosão (LRC), a adição de agentes modificadores do meio corrosivo (inibidores) e modificações no projeto dos equipamentos. Espera-se, portanto, que a utilização conjunta das diferentes abordagens proporcione a viabilidade de longo prazo da produção no Pré-Sal.

Aug 17, 2017

Failure of rock materials is a process of crack propagation. Crack initiation takes place when the crack tip stress intensity K reaches a critical value called fracture toughness, K1C. The rock fracture toughness is known to be affected by the surrounding environment such as temperature, confining pressure and humidity. In order to examine the effect of humidity, a series of semi-circular bend tests were performed under various water vapour pressures in a rock material that is known to be anisotropic. Water vapour promotes stress corrosion of rock and therefore the fracture toughness was found to have a decreasing trend with increasing water vapour pressure. The rate of decreasing the fracture toughness depends on the microcrack density that promotes the migration of water vapour into the rock. Also in an anisotropic rock, the fracture toughness depends on the direction of crack in relation to the anisotropy of the rock material.

Dec 6, 2010

By Warren H. Weisz

A cement, in the broad sense, is any substance which will cause various materials to adhere to each other. Clay was probably the first material to be used by man as a cement or binding agent. Water occurs in or is mixed with the clay to make it plastic, so that it can be formed in place. The sun and air remove the water from the clay and on drying strength is developed. The clays unless fired are not too resistant to water, therefore, their use is best when restricted to dry areas. Gypsum used as a cementitious material is not the subject of this paper, but its use dates back thousands of years. Gypsum mortars were used by the Egyptians in building such massive masonry structures as the pyramids. The Egyptian mortar consisted of a mixture of sand with burned gypsum (of an impure type of 81.5 per cent calcium sulphate and 9.5 per cent calcium carbonate) for the cementitious material. The burning of this type of cementitious material took place at relatively low temperature. These burning reactions will be covered later when the dehydration of gypsum is discussed. The setting of the partially dehydrated gypsum is considered to be crystallization from a supersaturated solution which deposits crystals of dihydrate (gypsum). In low water-content mixes, the interlocking of the needle-like crystals helps to produce higher strengths. Slaked lime made from limestone burned at higher temperatures (1648 F is generally considered as the calcining temperature, although under certain conditions incipient calcination will take place at 1250 F) is another early-period cementitious material. During slaking with water, a colloidal or amorphous hydrated lime is formed. When it is allowed to dry, it hardens and develops low strengths. On exposure to the carbon dioxide of air in the presence of some moisture, carbon dioxide is adsorbed and part of the calcium hydroxide is converted to calcium carbonate. Structures in which a lime mortar is used continue to grow in strength as this reaction proflesses. Hydrated lime has the disadvantage of not setting under water.

Jan 1, 1960

By H. W. Gillett, A. E. RHOADS

In its study of methods for reducing metal losses in the non- ferrous metal industry, the Bureau of Mines has conducted a long series of experiments on electric brass melting and collected much data on the experiments of others. Reports bearing on this work that have already been published by the Bureau of Mines are Bulletin 73, "Brass-furnace practice in the United States," and Bulletin 77, "The electric furnace in metallurgical work." A comprehensive report describing the design and operation of all types of electric brass furnaces and showing their performance in experimental tests on a commercial scale is in course of preparation. However, commercial tests of several new and promising types of furnaces are still under way, the results of which should be included in any general discussion of the subject. For this reason it has seemed desirable to issue a preliminary bulletin giving the data on a type of furnace developed in one stage of the bureau's work.

Jan 1, 1918