Search Documents

By George C. Coupland

"THE PRELIMINARY EVALUATION of the orebodies was computerized for tonnages and grades on a 20- by 20-ft grid. The evaluation was based on drill-core intersections over 40-ft vertical projections coinciding with the proposed bench intervals, taking the deviations of the drill holes into account. The computer print-outs gave an ore distribution and evaluation bench by bench and indicated the areas of varying mineralization. The two orebodies have a combined length of 2,200 ft. and a maximum width of 600 ft. They strike almost due north, dip about 85 degrees east and rake to the north. The computer print-outs were used to design an open pit with an over-all waste to ore ratio of 2.58:1. At the outset, the waste to ore ratio was 4:1. The pit is tear-drop shaped, with the narrow end to the south, and at the surface is 2,600 ft long by 1,800 ft wide. Ramps are 100 ft wide, with a 10% grade. The south ramp is left-handed, starts at the southeast and will continue to the bottom of the pit. A second ramp on the west and north walls runs from surface to join the south ramp at 7 bench. This ramp will handle the total pit production when part of the south ramp, from 4 bench to surface, is lost due to the underground operation. Over-all wall slopes are 53 degrees, and are laid out to avoid prominent protuberances which could relax and become unstable and potentially dangerous (Fig. 1) ."

Jan 1, 1974

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By Soumitry J. Ray

Poor visibility of powered industrial vehicles, such as forklifts, used in industry is often the cause of accidents that include pedestrians. Current standards allow up to 20 % non-visible regions for forklifts where measurement of these regions is performed by using lamps. A collaboration of research organizations, including National Institute of Standards and Technology, Georgia Institute of Technology (NIST), and Direct Dimensions, has been evaluating advanced methods for measuring a forklift operator?s visibility. These methods can potentially improve visibility standards. They can also help forklift and sensor manufacturers to determine (1) how visibility-assist sensors and algorithms can be designed and (2) where sensors can be mounted on forklifts. This paper includes explanation of visibility measurement experiments performed and results, associated language suggested to standards organizations, and a prototype design for measuring the visibility of forklifts automatically.

Aug 1, 2013

By J. P. Harrison, J. A. Hudson.

ABSTRACT: When considering the rock stress component of rock mechanics design, the basic procedure is to consider the pre-existing stress-state in the rock mass and then estimate the disturbance to this stress state as a result of engineering excavation. Failure criteria are applied to the final stress state to establish whether failure will occur. However, during the evolution of the stress state, the failure locus may be reached before the anticipated failure state and, in this case, failure will occur unexpectedly. This indicates that the complete stress path (defined as the variations in magnitudes and orientations of the stress tensor components resulting from engineering-induced or natural changes) must be considered. We list a set of stress path principles with their corollaries and then introduce a new and powerful method for simultaneously illustrating changes in the six independent components of the stress tensor. This method plots the magnitudes of the principal stresses above their orientational paths on the hemispherical projection, to provide a three-dimensional stress path locus for each of the three principal stress components. In connection with this presentational device, we illustrate a number of concepts associated with the stress path in rock engineering. For example, we show how the minor principal stress approaches zero at an unsupported excavation face, the interchange of the trajectories of two principal stresses when their magnitudes become equal, and the influence of the bounds on the principal stresses given by strength criteria. RESUME: Si on s’interesse à la composante “contrainte” lors d’un dimensionnement en mécanique des roches, la méthode de base consiste à considérer l’état de contrainte pré-existant dans le massif rocheux, puis d’estimer la perturbation à cet état générée par l’excavation projetée. Des critères de rupture sont appliqués à l’état de contrainte final pour établir si une rupture va se produire. Cependant, lors de l’évolution de l’état de contrainte, la surface critique peut être atteinte ce qui provoquera une rupture anticipée et, dans ce cas, cette dernière sera inattendue. Cela indique que le chemin de contrainte complet (défini par les variations de l’intensité et de l’orientation des composantes du tenseur des contraintes liées à des causes anthropiques ou naturelles) doit être pris en compte. Nous présentons un ensemble de règles pour les chemins de contraintes ainsi que leurs corollaires et, ensuite, nous introduisons une méthode, nouvelle et puissante, pour présenter simultannement les changements des six composantes du tenseur des contraintes. Cette méthode consiste à tracer l’intensité des contraintes principales sur le chemin d’orientation des contraintes à l’aide d’une projection hémisphérique afin d’obtenir le lieu, en trois dimensions, de chaque contrainte principale. En relation avec cet outil de représentation, nous illustrons certains concepts associés au chemin de contrainte en ingénierie au rocher. Par exemple, nous montrons comment la contrainte mineure tend vers zero à la surface d’une excavation sans soutenement, le changement de direction des deux contraintes principales quand leur intensité deviennent égales, et l’influence des conditions aux limites sur les contraintes fournies par un critère de rupture. ZUSAMMENFASSUNG: Bei ingenieurmassigen Taetigkeiten in Felsgesteinen ist es noetig die ungestoerten Gesteins Stress Componenten, die vor einem anthropogen Eingriff im Gestein vorhanden waren, zu kennen und erst dann Vorhersagen ueber Stoerung des Stress Zustandes, der durch einen ingenieurmaessigen Eingriff hervorgerufen wird, herzuleiten. Kriterien fuer das Versagen werden im letzten Stadium, des Stress Zustandes angewendet, um zu erfahren ob ein Versagen wohl eintreten wird. Es ist jedoch zu beachten, dass waehrend des Stress Aufbaus ein oertliches Versagen eintreten kann, welches vor dem eigentlichen, erwarteten Versagens Zustand auftritt. Diese Moeglichkeit weist darauf hin, dass der gesammte “Stress Path” (definiert durch die Variationen der Stress Tensor Komponenten in Richtung und Groesse, hervorgerufen durch ingenieurmaessig hervorgerufene oder natuerlich Vorgaenge) betrachtet werden muss. Wir fuehren eine Liste der “Stress Path” Prinzipien auf und stellen dann eine neue und wirksame Methode zur gleichzeitigen Darstellung der sechs unabhaegigen Komponenten des Stress Tensors vor. Diese Methode stellt die Groesse der “Principal Stresses” in Abhaengigkeit von ihrem rauemlichen Weg auf einer hemispherischen Projektion dar und erlaubt hiermit eine drei dimensionale Darstellung fuer jeden Ort des “Stress Path’s” in die drei Haupt Stress Komponenten. Im Zusammenhang mit der hier gegebenen Darstellungsart, verdeutlichen wir eine Reihe von Konzepten in der Felsmechanik. Wir zeigen zum Beispiel, wie der “Minor Principal Stress” Null zustrebt an einer Wand von einer nicht abgestuetzten Ausschachtung, den Austausch von Trajektorien zweier “Principal Stresses” wenn ihre Groessen sich gleichen, und den Einfluss der Groesse von “Principal Stresses” bei gegebenen Kriterien des Festgkeits Versagens.

Jan 1, 2003

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By Thomas L. Vandergrift

To significantly increase the stability of underground excavations while exploiting the full advantages of confined rock strength, methods must be developed to actively control the distribution of stresses near the excavation. This U.S. Bureau of Mines study examines theoretical and practical aspects of rock pres¬surization, an active stress control concept that induces compressive stress in the wall rock through repeated hydraulic fracturing with a settable fluid. Numerical analyses performed by incorporating the rock pressurization concept into a variety of boundary-element models indicate that rock pressurization has the potential to improve underground excavation stability in three ways: (1) by relocating stress concentrations away from the weak opening surface to stronger, confined wall rock; (2) by inducing additional stresses in a biaxial stress field to reduce the difference between the principal stress components near the surface of the opening; and (3) by counteracting the tensile stresses induced in the rock around internally loaded openings. Practical aspects of the rock pressurization concept were investigated through a series of hydraulic fracturing experiments. The use of sulfur as a settable fluid for hydraulic fracturing was demonstrated, although problems related to sulfur viscosity suggest that other molten materials, such as wax, may be better suited to practical field application of the rock pressurization concept.

Jan 1, 2010

In subterranean mining operations, access to communication networks deep underground is critical for transporting data, voice and video, and other supporting applications that are essential for efficient and safe operations. Whether accessing sophisticated ERP or maintenance management systems, engaging in fleet management, video surveillance, or access control, or protecting miners with wireless locator systems, these networks serve as a literal lifeline between workers deep within mines and surface operations. For this, mining networks require more than permanently installed network cabling, it also requires unique deployable systems designed for quick installation, extension and even relocation as the active mine site area moves, or equipment is moved in and out.

Mar 1, 2014

By S. N. Lekakh

Phosphorous segregated at grain boundaries during solidification and heat treatment dramatically decreases low temperature toughness of precipitation hardened Fe-Mn-Al-C austenitic steel. A thermodynamic analysis was performed to evaluate the possibility of decreasing P and subsequent segregation by Ca- and Ce-additives in the melt. It was shown that the predicted probability of forming a P containing compounds depends on melt composition and treatment sequence. Experimental heats were performed and several micro- and macro-structural effects of Ca- and Ce-additives were recognized by using an automated inclusion analysis technique.

Jan 1, 2010

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

The process of pile driving disturbs the soil around the pile. The nature and magnitude of disturbance depends upon 1) the pile size, and 2) the nature of soil. Therefore, the prediction of a single pile behavior based on soil properties of undisturbed soil samples may not match its performance. Under lateral loads, the pile may loose contact with the soil near the ground surface especially in clays. The soil pile interactions are influenced the most by pile behavior in this zone. This situation further affects the tally of prediction and performance. Piles are used in groups. The zones of overlapping stress from one pile to the other both around the pile and below their tip particularly in soft soils, contribute to group effects. Empirical solutions have been developed for prediction of the pile group behavior. The group action is more involved under vibrations. Several cases of single piles and pile groups under static and dynamic loads from published records have been analysed. It has been shown that single pile test is the best source of information on the soil-pile-soil interaction effects.

Jan 1, 1989

By E. D. Gardner

This is one of a series of papers describing mining and related subjects affecting mining in western mining districts and mineralized areas. The parts of this paper pertaining to current production, mining and milling methods and practices, and general conditions affecting mining were collected principally during a field survey made in May 1935. Some original data obtained on previous visits to the area are also included. The history, geological background, and past production of the mines and district are largely abstracted from previous publications, for which due credit is given later in the test. The principal districts in the Black Mountains are the Oatman or San Francisco and the Union Pass or Katherine. This range contains the principal producing mines of the State, in which gold is the only important metal. Although the total production of gold is relatively small as compared to other districts where the precious metals are obtained as a by-product in copper min¬ing, the area is one of considerable economic importance to the State.

Jan 1, 1936

By W. G. Worcester

Generally speaking, the term 'clay' appears to convey but little to the average layman other than of a sticky substance to be rigidly avoided when making a cross-country drive in the family ark- especially so if the chains have been left behind. On the other hand, the technical ceramic; engineer, though his chariot be bogged in the self-same mud-holes, will, more than likely, be planning on ways and means for the conversion of the troublesome gumbo into paving bricks over which all might ride with pleasure and security. However, to come to the point, the term 'clay' bears much the same relation to the ceramic world that the term 'ore' does to the metallurgical; in other words, as there are many kinds of ores, so also are there many kinds of clays, and it therefore becomes necessary to classify and sub-classify them previous to a discussion of their relative values and importance. Hence, a brief digression will be made from the main topic of this paper in order to enumerate and classify a number of the more important types of clays. By so doing, the relative position of Saskatchewan clays, later discussed, will be better understood.

Jan 1, 1929

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Ad. Breyre

[Internal-combustion engines have been used in Belgian mines for a long tine. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted' in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they were replaced later by electric or compressed-air motors. However, the number of gasoline locomotives continued to increase. Regulations governing the use of these locomotives soon were formulated and as early as 1920, when a now set of regulations was promulgated, the use of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have boon incorporated in the regulations.]

Jan 1, 1940

By Ad. Breyre

Internal-combustion engines have been used in Belgian mines for a long time. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they wore replaced later by electric or compressed air motors. However, the number of gasoline locomotives continued to increase. Regulations governing; the use of these locomotives seen were formulated and as early as 1920, when a new set of regulations was promulgated, these of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have been incorporated in the regulations.

Jan 1, 1940

By John F. Papp

International and U.S. chromium material flow, losses, and environmental releases and transfers from mining through industrial processing, end use, and recycling are identified and quantified. Average (1983-92) U.S. consumption has been: metallurgical industry, 87 pct; chemical industry, 10 pet; and refractory industry, 3 pct. Average chromium content of aluminum, cobalt, copper, nickel, and titanium alloys and alloy, carbon, and stainless steel alloys was estimated. Anthropogenic chromium consumption was estimated for the cement and copper industries. N on-commodity cycle anthropogenic chromium mobilization resulting from U.S. fuel and fertilizer use was estimated. Commodity cycle anthropogenic world chromium loss from mining and primary consumer industry was estimated to be equivalent to about 56 pct of chromium contained in chromite ore production and represented a loss rate of 181 kt-Cr/Mt-CrOre. Chromium released to the atmosphere from natural and from anthropogenic sources were comparable in magnitude. Chromium released to soil was mostly from anthropogenic sources, and aquatic releases were all anthropogenic. Domestic product chromium losses exceed process losses by more than a factor of 10 showing the importance and potential environmental impact of post-consumer recycling. The location of historical and current domestic chromium industry processing sites in 23 States were reported. Chromium releases and transfers to the environment were estimated from 1973 through 2002 by primary consumer industry. A decrease in chromium releases and transfers to the environment was anticipated.

Jan 1, 1995

By Mark Eisner

ONE'S JOB is the watershed down which the rest of one's life tends to flow write the Lynds in the first pages of their classic social study, "Middletown in Transition." Certainly engineers will confirm this statement after a check among those in their own profession with whose lives they are at all familiar. I have no hesitancy in acknowledging the truth of their observation for the men and women who are engaged in the profession of the law. It has been often remarked that American public life is overrun with members of the law profession. The highest public office in the land, that of President. has been occupied by lawyers almost to the exclusion of citizens of any of the other professions. Twenty-two Presidents of the United States out of the total of 31, were members of the bar. For the most part, members of Congress, the governors of the states, the state legislators and the mayors and other local leaders, men who occupy important positions of responsibility and public trust, have had legal training. Now this fact is no mere accident. Those who were fitted for the "job" of the practice of the law are favorably placed with respect to their participation in public life. Thus public service and public office is the watershed down which the "lawyer's" life tends to flow.

Jan 1, 1940

By A. Kazemi, M. A. Ahmadi

Pressure tunnels are constructed nurously in related with powerhouse. In some cases, according to high internal water pressure, rock mass around tunnel can seldom suffer this pressure. So installation of concrete lining which interacts with rock mass and suffers parts of this pressure and transfers the rest of the pressure to the rock. In this paper hydromechanical interaction between rock and lining is investigated. With using empirical and numerical methods concrete lining for Symareh waterway is designed. Initial support of 10 cm reinforced shotcret with wire mesh and rock bolts pattern of 2.5*2.5 m with length of 4 m is suggested. By using FLAC package final lining with paying attention to axial force and momentum in reinforced concrete was designed. Reinforced concrete with 60 cm thickness and two rows of bars, 18 mm diameter and 20 cm spacing are designed. Also for preventing cracks in concrete which caused by the change of temperature and shrinkage, bars with 10 mm diameter and 25 cm spacing, and also bars with 8 mm diameter and 10 cm as minimum shear bars are suggested. Plusieurs galeries en pression se construisent en liaison avec les centrales électriques. Dans certaines galeries, suite à une haute pression interne de l'eau, le massif rocheux autour de la galerie ne peut pas supporter cette pression. L'installation d'une couche de béton a l'intérieur de la galerie donc réagit avec les roches et support d'une partie de cette pression et transfère le reste de la pression aux roches. Dans ce papier, l'interaction hydromécanique entre la roche et la couche en béton a été étudiée. En se basant sur les méthodes empiriques et numériques le système de support de galerie de passage d'eau de Saymareh a été conçu. Un soutènement initial d'une épaisseur de 10 cm de béton étant renforcé par un grill métallique et une maille de boulon (2.5 * 2.5 m) d'une longueur de 4 m a été proposé. En utilisant le logiciel de FlAC, la couche finale en béton selon les forces dans le béton a été conçue. Le béton renforcé d'une épaisseur de 60 cm et deux ranges d'armateurs (18 mm de diamètre) avec un intervalle de 20 cm a été conçu. De plus; pour éviter des fissures dans le béton suite au changement de la température et de l'extraction, des armateurs de 10 mm de diamètre et de 25 cm d'intervalle pour augmenter la résistance au sciesiement du béton ont été proposes Unter Druck stehende Tunnels werden hauptsaechlich im Zusammenhang mit Kraftwerken gebaut. In einigen Faellen, wo der Wasserdruck zu hoch ist, Kann selten die Felsenmasse diesen hoehen Druck allein aufnehwen. Deshalb werden sie mit Betonauskleidung versehen, die wegen guter Wechelwirkung mit der Felsenmasse einen Hauptanteil des Druckes aufnehmen Kann, wobei der Rest an die Felsenmesse weitergeleitet wird. In dieser Arbeit wird die hydromechanische Wechelwirkung zwischen der Gesteinmasse und der Auskleidung untersucht. Mit Hilfe empirischen und numerischen Verfahren sowie Kombination der beiden wurde eine Betonauskleidung fuer die Symareh Wasser Kannal koustruiert. Als erstes wurde ein 10Cm dicker armierter Beton mit einem Mashengitter von 2.5*2.5 sowie den gleichen Felsbolzenabstaenden und einer Laenge von 4 m vorgeschlagen. Mit Hilfe des FLAC Programms wurde die Hauptauskleidung unter Beruecksichtigung von Axialkraeften und Momenten im Stahlbeton koustruiert. Der 60 Cm dicke Stahlbeton wurde mit zwei Reihen von Stangen, 8 mm im Durchmesser und in Abstaenden von 20 Cm koustruiert. Ferner im Sinne der Vorbeugung gegen Rissen im Beton, die durch Temperatur aendeungen und Schrumpfungen bedingt sind, wurden Stangen mit 10 mm Durchmesser und 2.5 Cm Abstaenden zur Erhoehung vor Scherfestigkeit des Betons vorgeschlagen.

Jan 1, 2003