Search Documents

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

By Masaki Imamura

A novel hydrometallurgical process for copper concentrate treatment has been developed by Niihama Research Laboratories of Sumitomo Metal Mining Co., Ltd. The process has numerous advantages with respect to the operational and environmental aspects. For example, copper is leached effectively from chalcopyrite concentrates by chlorine gas under atmospheric pressure. The copper in the leach solution is then separated from iron and silver by solvent extraction and undergoes electrowinning for its recovery as a highly pure copper metal; this does not require any further purification. Moreover, iron metal can be produced from the purified raffinate by electrowinning without generating a large volume of goethite or hematite, which are solid wastes generated due to iron rejection in common hydrometallurgical processes. This process can also realize the efficient recovery of precious metals. The results of batch testing and continuous-operation testing are presented in this paper.

Jan 1, 2006

By R. Lusignea

A device has been developed for nondestructive testing the holding power of split tube friction rock supports. It operates by measuring the amount of decrease in internal volume when the support is forced into the drilled hole. The pullout force or slip load is a function of this decrease in volume. The device gives readouts of the average internal diameter and predicted pullout force or the support. Laboratory and field tests showed excellent repeatability and good correlation between predicted and actual pullout force. The device is hand-operated, lightweight (7.5 lb) and can be used on any friction support.

Jan 1, 1983

By R. J. Thompson

Well-designed and maintained haul roads are the key to minimizing truck haulage onroad hazards and costs, as well as increasing productivity. In practice, however, designing and managing a haul road for optimal performance is often difficult to achieve, especially when resources assigned to design and construction are constrained. By understanding how a road design is developed from geometric, structural, functional and maintenance considerations and, critically, the interplay between these components in design and operation, optimal performance can be achieved. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for safer and more efficient haulage systems, the truck manufacturers’ requirements for a more predictable and controlled operating environment and the recognition of human factors as a significant contributor to haulage accidents. While the human factor is the most problematic to address in a road design, the paper shows that the more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By Liu Run, Jia Zhao-lin, Yan Shu-wang

"Piles with diameter larger than 2m in engineering can be defined as large diameter pile, and piles used for oil platform foundation in Bohai Gulf, are usually over 100m long and 2m in diameter. Such long piles have to be manufactured by segments before installation, because of transformation and hoisting difficulties. The segments of the pile are assembled by welding during installation one to another. Normally, assembling two pile segments takes one day or even a longer time, which mainly depends on construction conditions. After pile segment assembling, it proves to be difficult to restart the successive penetration. The mechanism of pile refusal is discussed and the process of driving a segmented pile is simulated with a finite element program. The calculating results show that, when the stick-up stability was satisfied, increasing the length of the last segment of the pile and assembling the pile segments when the pile tip penetrates into a clay layer could greatly ease the difficulty of driving the pile. Furthermore, cutting down the pile extension time is also one of the most effective measures to minimize the refusal risk.1. InstructionIn recent years, more and more oil platforms with six or eight legs have been adopted in Bohai Gulf, China. The leg piles with diameters of 2m or more have to be driven to about 100m below the sea bed. Such long piles have to be manufactured by segments before installation, because of transportation and hoisting difficulties. The segments of the pile will be assembled during installation, in which a successive segment will be attached to a formerly penetrated one by welding (Fig.1). The assembling work often takes one day or even a longer time."

Jan 1, 2014

By AIME AIME

COMMITTEES. CENTRAL GENERAL COMMITTEE.-Wm. Fleet Robertson, Chairman; Win. M. Brewer,. Secretary. LOCAL COMMITTEE OF NELSON, B. C.-A. S. Farwell, Chairman; W. C. Bayly, Secretary; William Blakemore, M. S. Davys, S. S. Fowler, R. R. Hedley, Leslie Hill, A. H. Telly; W. C E. Koch, J. J. Campbell. LOCAL COMMITTEE OF ROSSLAND, B. C.-His Worship Mayor Hamilton, Chairman; AV. H. Aldridge, Charles Biesel, H. H. Claudet, F. W. Guernsey, R. Marsh, J. W. Astley, R. W. Brock, A. A. Cole, A. G. Larsen, R. H. Stewart. Also the Rossland Board of Trade, Robert Hunter, President; K. E. Mackenzie, Vice-President; A. B. Mackenzie, Secretary. LOCAL COMMITTEE OF GRAND FORKS, B. C.-His Worship Mayor Hammor, Chairman ; A. W. B. Hodges, A. L. White, G. M. Fripp, L. A. Manley, W. T. Spier, G. W. Wooster. LOCAL COMMITTEE OF VICTORIA, B. C.-Wm. Fleet Robertson, Chairman; William Al. Brewer, Secretary; Harold Grant, Thomas Kiddie, Clermont Livingston, E. C. Musgrave, W. J. Sutton, Francis A. Thomson. LOCAL COMMITTEE OF VANCOUVER, B. C.-C. F. Jackson, Chairman; His Worship Mayor F. Buscombe, J. J. Banfield, A. Bethune, John Boyd, H. C. Clarke, A. B. Erskine, E. P. Gilman, William Godfrey, W. D. Haywood, R. K. Houlgate, H. T. Lockyer, J. I. McAdam, H. M. McDowell, C. W. McMeekin, W. H. Malkin, F. Richards, T. J. Smith, George A. Walkem, G. Slieldon Williams. LOCAL COMMITTEE OF WHITE HORSE, Y. T.-Robert Lowe, Chairman.; T. W. Jackson, Secretary; George -Armstrong, A. L. Bindley, Rev. Father Corbeil, L. De Gex, A. E. Fisher, W. P. Grainger, P. D. McMillan, Rev. Mr. Main, George C. Mallot, Alfred Parre, George Pulham, George Reid, William Robinson, J. P. Scharschmidt, J. C. Schraeder, Major A. E. Snyder, Rev. Mr. Stringer, Judge George L. Taylor, William Taylor, H. Wheeler, E. J. White, J. P. Whitney;' ; LOCAL COMMITTEE OF DAWSON, Y. T.-Hon. W.W. B. McInnes, Commissioner of the Yukon Territory, Honorary Chairman; Major Z. T, Wood, Assistant Commissioner of the Yukon Territory, Honorary Chairman; J. B. Tyrrell, Chairman; J. Moore Elmer, Vice-Chairman; George Black, Secretary; Hon. Mr. Justice Dugas, Hon. Mr. Justice Macaulay, Hon. Mr. Justice Craig, Dr. Alfred Thompson, D. A. Cameron,. E. W. Griffin. The first session, held in the ministers' room of the Parliament Building, 3 p.m., Saturday, July 1st, was presided over by Past-President Robert W. Hunt. His Excellency the Lieut.-

Nov 1, 1905

By Anna Sukhanova, Svetlana Babaeva, Sergey Andreev, Victor Beltenev

"The Zenith-Victoria /1/ and Jubileynoye /2/ hydrothermal fields have symmetrical structural position on the Mid Atlantic Ridge (Fig. 1). In order to compare the evolution of hydrothermal systems, we conducted mineralogical and geochemical studies of SMS from both sites.Radiochemical and geochemical investigations of massive sulfides of the Zenith-Victoria field distinguishes three major stages of evolution: initial, interim and final represented by Fe-S, Cu-Fe and Zn-Fe types of SMS respectively /3/. In this talk, we describe the results of geochemical analysis of massive sulfides from the Zenith-Victoria field. Geochemical varieties of SMS are considered to be indicators of the evolutionary stages of the hydrothermal system."

Sep 1, 2014

By Felix Edgar Wormser

JUST as the ancients used the products of their crude mining endeavors to fashion tools with which to make digging easier, so today mining enterprises are dependent upon the very metals they mine for the efficient conduct of mining and metallurgical operations. In fact, the outlet afforded by the production of minerals in the United States is no mean market for the nonferrous metals. I believe that mine managers frequently lose sight of the opportunity they have to select from competitive products those which will help the market for their own metal output. For example, some years ago a large lead mine used storage-battery locomotives for its haulage, common practice, of course, throughout the United States. These particular locomotives, however, were powered not with the ordinary lead storage battery but by a competitive battery product made from an imported metal. After studying this situation, the manager saw how he could help himself by purchasing a product made from his own mineral output, and in his next order turned tip the use of the lead storage battery.

Jan 1, 1935

Jan 1, 1998

By Hubert Law, Dan A. Brown, Kyle M. Rollins

"Soil mixing and jet grouting provide a means to significantly increase the lateral resistance of pile group foundations with relatively little investment of time, effort, and expense compared to the cost for additional piles necessary to produce the same increased resistance. Comparative field testing conducted on full-scale pile groups before and after treatment of small soil volumes showed significant improvement in lateral resistance. The lateral resistance of the pile group increased by 60% due to soil mixing and by 180% due to jet grouting. To provide additional understanding regarding the influence of the soil mix strength, depth of improvement and width of improvement, a series of parametric studies were performed using a 3D finite element model. This set of “virtual load tests” was then combined with the results from the actual field tests to help develop a simplified model to account for observed behavior. In general, the testing and analysis indicate the pile group and the surrounding improved soil block generally act as an equivalent “super pile”. The passive force, side shear and base shear on the improved soil surrounding the pile group itself increased lateral resistance. This increase in resistance from the soil block can be added to the lateral resistance of the pile group.INTRODUCTIONThe lateral resistance of pile groups is often critical to the design of bridges and high-rise structures subject to seismic, wind, wave and landslide forces. Typically, when analyses indicate that the lateral resistance of a foundation is inadequate, additional piles, drilled shafts or micro-piles are added to increase the lateral resistance. Furthermore, an expanded pile cap or connecting beam is often required to structurally connect the new piles to the existing pile group. While this approach provides the required lateral resistance, it may also be relatively expensive and time consuming. An alternative approach is to use soil improvement techniques to increase the strength and stiffness of the surrounding soil and thereby increase the lateral resistance of the pile group. The improved zone could potentially be relatively shallow because the lateral resistance of piles is typically transferred within 5 to 10 pile diameters. For example, the soil around the periphery of the foundation could be relatively easily improved for an existing foundation as illustrated in Fig. 1(a) using a variety of soil improvement techniques. Alternatively, the soil under the foundation could be improved for a new foundation or even for an existing foundation with a technique such as jet grouting (see Fig. 1(b)). Improving the soil under the foundation would have the potential for producing greater increases in lateral resistance because the improvement would reach interior piles. In addition, the process of creating a cemented “soilcrete” zone around pile foundations could potentially produce a zone which would behave like a reinforced “superpile” with increased structural stiffness."

Jan 1, 2015

By H. A. Hamza

An experimental study of the settling characteristics of a washery effluent originating as tailings from a froth flotation circuit was undertaken by using a systematic approach to select the most appropriate flocculant(s) under predetermined conditions. Selection and evaluation procedures which greatly reduce the effort required to select flocculants are described. The results show that, although different flocculants display superiority at different ranges of dosage. Separan MG 700 (Dow) is the most suitable on absolute economic grounds. Flocculant evaluation is based on a Cost Performance Index (CPI) which expresses the cost of flocculant (¢/ton) required to produce a unit settling rate (in./hr). From experiments carried out with a number of flocculant aid and flocculant combinations, it was concluded that the use of flocculant aids can be economically justified only if the settling rates required are higher than those obtainable at the optimum flocculant dosage. Otherwise, the value of the flocculant aid appears to be limited largely to the reduction of supernatant turbidity.

Jan 1, 1979

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By C. Rodriguez, T. BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle. Blasting is the first and lowest cost per ton stage in the comminution value chain. The basic principle that effective blast design can optimize fragmentation from the Run of Mine (ROM) ore muck pile to improve productivity through digging, loading and crushing to grinding and increase mine site profits has been well documented. Benefits of controlling fragmentation in the blast include reduced wear on equipment, faster loading, increased truck loads while detecting oversize rocks at the muck pile can reduce the frequency of a blocked primary crusher. A second basic principle is a measure of particle size distribution (PSD) at each unit operation in the comminution cycle allows engineers to manage blast design to produce fragmentation in the ROM ore most suitable to optimize downstream unit processes to improve mine site productivity and profits. Split-Online® systems have measured PSD of rocks on conveyors from the primary crusher to the SAG mill for over 20 years. Split-Engineering partnered with various mining companies to develop Split-ShovelCam® to automatically measure fragmentation from shovels and excavators working the ROM muck pile. This paper takes the reader “Back to Basics” by discussing the use of real time fragmentation analysis at the muck pile as an important parameter to optimize energy factors required for each blast. Case studies are given. INTRODUCTION The basics of mining are: • Explore for and find economic resources of valuable minerals • Mine rocks containing valuable minerals using blasting • Crush and grind rocks to liberate valuable minerals (comminution) • Recover valuable minerals for sale Comminution is an energy intensive process which accounts for a major proportion of mine site costs. Effective blasting can improve comminution and deliver significant reductions to mine site unit costs, (CEEC, 2016). Engineers, scientists, builders and even philosophers have long promoted the phrase “measure to manage”; the premise being “you can’t improve what you don’t measure”. Blast Engineers measure fragmentation in ROM ore for feedback to manage energy input in the design of blast patterns to optimize the ROM product size for downstream operations, whether they be for ROM Leach or feed into the primary crusher.

Jan 1, 2019

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Carlos Frias

The lead-acid battery recycling is a major industrial activity (more than four million tonnes recycled lead per year) that generates large amounts of toxic wastes such as lead slag, mattes and acidic sludge, besides airborne emissions. This is a waste-producer industry that needs a definitive solution to avoid its negative environmental impact and getting a sustainable lead production. That is the principal target of the CLEANLEAD technology, which properly combines both hydrometallurgical and pyrometallurgical routes aiming to get zero-waste production, reducing the use of energy and resources in all phases of battery reprocessing, and consequently, greatly decreasing the operating cost. There will be no toxic emissions to land, water or air, and obtained products are pure lead metal or pure lead oxide, and commercial gypsum instead of waste sludge.

Jan 1, 2006

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By Hou Shitao

With the development of Wuhan's city planning in China, new buildings of moderate and high store have been increasing day by day. Precast concrete piles or cast-in-site piles were used in the major foundations of the buildings. In process of their design and construction geotechnical engineers are concerned very much about practical bearing capacity and construction quality of pile foundations. In order to grasp accurately the cases static loading or vibration test is used generally to judge them. At present, the major questions in existence are that although a load is applied directly on pile and measured datums are reliable for static loading test, it must take a lot of work and longer time and engineering cost is higher. A vibration test has the advantages of which checking up of pile quality can be performed rapidly, the test is simple and convenient, and scope measured wide. But bigger error exists generally in measured datums. Therefore, it is nesessary to make vibration test on piles more perfect for pile foundation engineering. It is stated in paper that adapted technique of vibration test on piles is quite right in developmental direction sense for pile foundation. There are a great variety of vibration test methods on piles. A few of methods which often are adapted in practice can not meet the need of different practical engineering. It is also an important question whether the instruments of vibration test and relevant computer softewares make a response accurately for practical case. Different sequence of operation and technical requirements comes into being some influence directly on the test results. Meanwhile, different combination of soil stratigraphy, soil texture, groundwater and pile could cause different error of test datum. It is necessary to analyse and judge objectively the results of vibration test. Therefore, on the basis of developing and perfecting further the technique of vibration test, the applied technique of vibration test should be standardized so that better test results can be obtained.

Jan 1, 1991

By Jr. Holmes

The Bureau of Mines drilled and sampled the more important magnesite deposits in the Currant Creek Mining District, White Pine County, Nev. The properties of the Ala-Mar Magnesium Co., Inc., and the Nevada Magnesite Co. were examined in August 1942 by D. W. Butner, engineer of the Bureau of Mines, to determine the advisability of investigating the deposits under the strategic minerals program. Development involving diamond drilling, trenching, and sampling was started September 1, 1942, and was completed in the latter part of November 1942. The deposits are on unsurveyed public land in T. 12N., B. 59 E., M.D.B.&M., in an area of high relief ranging from 7,300 to 8,100 feet in altitude. Both properties are situated northwest of the Tonopah-Ely Highway, U.S. Highway 6, from which a dirt road extends about 4.6 miles northwesterly, about 35 miles southwest of Ely, to the Ala-Mar property, and another dirt road extends about 10 miles westerly, about 26 miles southwest of Ely, to the Nevada Magnesite property. The magnesite occurs as irregular nodules, veins, and lenses in a bedded calcareous tuff formation, which overlies a group of volcanic rocks, and which is capped by remnants of rhyolite flows.

Jan 1, 1950

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist and in locating them quickly, with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of those jurisdictions or to contrast the varying provisions of many States upon a single subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although

Jan 1, 1943