Search Documents

By R. G. Sandberg

Many gold-bearing ores throughout the Western United States contain small quantities of mercury. The presence of mercury not only decreases the gold-loading capacity of the activated carbon, but complicates the fire refining of cathodes and creates a potential health hazard. The Bureau of Mines investigated methods to limit mercury extraction during gold ore leaching and to remove mercury from cyanide leach solu-tions. Mercury dissolution was reduced from 40 to 10 pct by decreasing NaCN concentration from 20 lb to 0.34 lb per ton of solution at a pH of <11. When 0.1 lb CaS per ton of ore was added to a leach slurry, mer-cury extraction was reduced from 27 to 0.4 pct. Less than 0.5 pct of the mercury was solubilized when <0.1 lb CaS per ton of are, along with lime and NaCN, was added to a simulated grinding circuit.

Jan 1, 1984

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers&apos; shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

By Luis Angel De Montreuil

Ante el problema del tratamiento de minerales complejos, la demanda de eficiencia metalúrgica y bajos costos de operación, el ingeniero busca el apoyo de la mineragrafía como estudio microscópico de los minerales económicos. En ese sentido, el presente texto señala la importancia de la minegrafía -en tanto ayuda a la flotación de los sulfuros valiosos de los yacimientos peruanos. Asimismo determina las propiedades de los minerales con el fin de identificarlos.

Jan 1, 1986

By Robert T. MacMillan

An essentially chemical technique has been developed on a small scale for the efficient utilization of certain domestic titaniferous iron ores. Three main steps are involved: (1) Sintering the ore at 1,050° C. with carbon and soda ash to reduce the iron to metal powder, retaining the titania in the slag, (2) separating the powdered iron from the slag, after wet grinding, by magnetic or gravity methods, and (3) sulfuric-acid decomposition of the titania fraction to produce pigment and certain byproducts. The technique was first applied to the tailings from the Bureau of Mines bauxite-concentrating plant at Bauxite, Ark. A good grade of powdered iron was produced from this material. Subsequently, the work was diverted to the study of the titaniferous magnetite from the MacIntyre Mine at Tahawus, N.Y., because of the potentially higher recoveries of iron, titanium and vanadium. Ninety percent of the iron in this ore has been recovered as an iron powder analyzing 90 percent metallic iron and containing 2 to 3 percent TiO2. The remaining titania was found in the slag and was recovered as pigment-grade TiO2 by application of a suitable technique. The vanadium was distributed between the TiO2 fraction and the alkaline liquor resulting from the wet-grinding and magnetic-separation operations, with only a minor proportion retained by the metallic iron.

Jan 1, 1950

By J. S. Hu

FTIR spectroscopy has been used for the characterization of adsorbed oleate at the fluorite surface. It has been found that modest changes in the adsorption density at high temperature and high oxygen potential do not provide a satisfactory explanation for the significant increase in the hydrophobic character of the system under similar conditions. Rather, FTIR spectroscopic measurements suggest that chemical interaction between adsorbed oleyl groups occurs at high temperature and/or oxygen potential and accounts for the increased hydrophobicity. Specifically, the intensity of the =CH bond of the adsorbed oleate diminishes at high temperature and/or high oxygen potential. Such a phenomenon was not observed in control tests with the calcium oleate soap. For extensive reaction at the fluorite surface, the presence of a new surface species has been identified. These results indicate that the fluorite surface catalyzes an oxidation and/or polymerization reaction between adsorbed oleyl groups which results in a more hydrophobic structure at the fluorite surface.

Jan 1, 1986

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By Charles Will Wright

The present struggle for economic and industrial supremacy by the Communist world is against the United States, its main target, and the other Free World nations. The basis of industrial power is minerals, so the Communist nations are building up mineral production within their borders, often regardless of costs, and are acquiring quantities of mineral products from Free World countries for future use. They are contracting for additional supplies and advancing funds for the development of these quantities. A number of the less developed mineral producing countries of the Free World are being infiltrated by Communists and Communistic influence. This situation is well known, but as yet little has been done to oppose these activities or to awaken the public to their seriousness. The Communist countries are still far behind the Free World Nations in production of many essential minerals. But, shortages are being made up from Free World nations in exchange for petroleum, manganese ore, chromite and other products. Restrictions on shipments of strategic materials to Communist countries have not been maintained.

Jan 1, 1964

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines-developed induction slag melting process is of concern to the titanium industry. The objective of the research was to determine the effect of removing the nonconductive molten calcium fluoride (CaF2) slag used as an insulator between the titanium and the segmented copper crucible. The data were obtained from single-induction-melted ingots prepared with no CaF2 insulating slag and an ingot prepared with the normal addition of 4 pct CaP2 slag. The results showed that the mechanical properties of single-induction-slag-melted and annealed Ti-6AI-4V alloy exceed the minimum values specified in "Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H." High-cycle, tension-tension fatigue testing yielded similar results. The data from 44 of the 45 specimens were contained within the typical scatter band for fatigue data on wrought Ti-6AI-4V alloy. Although the removal of the insulating slag is a desirable change, the data from the specimens with the previously standard 4 pct slag addition showed no detrimental effect from the slag inclusions.

Jan 1, 1988

By R. L. Crosby

A part of the liquidus of the magnesium-zirconium system was determined by chemical analysis of suction samples taken from the melt in the approximate temperature range of 850° to 1,450° C. The melt was prepared in a furnace pressurized with an inert gas. The average zirconium value in weight-percent of the liquidus composition at each sampling temperature was 0.96 at 867° C, 1.40 at 1,062° C, 2.05 at 1,262° C, and 2.96 at 1,402° C. The equilibrium solid phase was zirconium.

Jan 1, 1965

Exploring long-term future possibilities for your business and methods for achieving them are critical functions of leadership. More than ever, strategic initiatives today have to be planned and delivered in an environment of disruptive change û driven by shifting business or regulatory imperatives, new technologies and global economic change, and diverse stakeholder interests. The notion of The Future as a single inevitable outcome is obsolete. There are many possible futures. This paper explains an innovative process û known as scenario planning û to help executives in the construction and testing of longer-term strategies to deal with uncertainty.

Jan 1, 2006

By Jorge Tovar Pacheco

De acuerdo a las estadísticas del ANA, en el Perú solo aprovechamos el 47% del agua procedente de las lluvias y el restante 53%, desemboca en el mar. En ese sentido, el presente texto describe el manejo de los recursos hídricos a partir de las operaciones mineras. La minería moderna utiliza el 2% del agua durante sus etapas de exploración, explotación y cierre de operaciones. Durante la primera etapa, el agua es utilizada en muy poco volumen, tanto para las perforaciones como para el abastecimiento del campamento de exploración. En el cierre de las operaciones mineras se instalan canales de coronación para evacuar las escorrentías, se desarrollan programas de revegetación para evitar erosión y, si el potencial de generación de aguas ácidas es positivo, se operan plantas de tratamiento para mejorar la calidad del agua efluente. En consecuencia, la minería moderna es una actividad extractiva que genera sus propios recursos hídricos y la descarga limpia para el beneficio de los usuarios de aguas abajo, aplicando el responsable concepto de contaminador-descontaminador.

Jul 1, 2014

By A. Azizi, P. Blatter, A. Bouajila

"Due to the high reactivity of sulfide minerals in alkaline cyanide solutions, some parasitic reactions inflict a heavy gold surface passivation and excess cyanide consumption resulting in a dramatic decrease of the gold leaching rate. Atmospheric pre-oxidation was shown to be an effective tool to enhance gold extraction by preventing a passive film from forming on the surface of gold grains. This work aims to highlight efforts undertaken to determine: (1) how gold cyanidation is limited by passivation; (2) what are the reactions and mechanisms involved during gold cyanidation; and (3) how a better understanding of fundamental issues can be used to design a proper pre-oxidation strategy. INTRODUCTION Precious metals (PM), gold in particular, naturally occur in contact within a wide range of sulfide mineral systems. Hence, one of today’s most challenging R&D tasks consists in accounting for the presence of sulfides on the cyanidation behavior of gold. An important body of knowledge reveals that metal sulfides display a range of reactivities in alkaline cyanide solutions (Marsden & House, 2006). Such reactivities are acknowledged to inflict additional utility costs and loss of profits because they are accompanied with higher consumption of cyanide and/or formation of undesirable by-products that are often detrimental to gold leaching rates. Gold recovery in cyanidation is hampered by a multitude of factors, among others: (1) consumption of excess cyanide as a result of the formation of thiocyanate and dissolution of transition (Cu, Fe, Zn, etc.) metals (Habashi, 1967); (2) gold surface passivation by solid reaction products, e.g., Fe(OH)3 (Guo, Deschenes, Pratt, Fulton & Lastra, 2005), sulfur (Dai & Jeffrey, 2006; Jeffrey & Breuer, 2000;) or oxo and thiooxo (SbO33- SbS33-) salts in alkaline solutions (Guo et al., 2005). Because of their energy structure, most of the sulfide minerals exhibit semiconductor properties (Marsden & House, 2006). Therefore, the contact between constitutive sulfide minerals inside complex sulfurous ores entrains electrochemical phenomena in which sulfide dissolution is a genuine corrosion process (Azizi, Petre, Olsen & Larachi, 2010). For instance, galvanic interactions could be initiated between the various constituents within the ore and could substantially increase or decrease the reactivity of some of the associated minerals."

Jan 1, 2012

By C. H. Li, R. J. Stokes, T. L. Johnson

The effect of alumina particles on the nucleation and growth of cracks through a silver- chloride matrzx has been investigated. It has been found possible to promote fibrous cracking in dispersion-strengthened silver, chloride under notch-impact conditions at temperatures at which silver chloride alone cleaves brittlely The modification) of fracture beIzavzor is thought to be due to the relaxation of hydrostatrc stress beneath a notch by the nucleation of cavities near alumina particles. In recent years, composite or dispersion-strengthened materials have been studied primarily to understand their high resistance to plastic flow particularly at elevated temperatures. Dislocation models have been developed with which it is possible to deduce with fair success the effects of interparticle distance, particle size, temperature, upon yielding and creep behavior.l-4 Much less attention has been paid to the fracture behavior of these materials (with the notable exception of common structural steels) and little is known experimentally about the manner in which inclusions affect the nucleation and growth of cracks through a matrix. Nevertheless a beginning has been made in connection with fibrous cracking in ductile matrices where inclusions appear to play an essential ro1e.5-7 During the severe localized plastic deformation which accompanies necking in a tensile test, cavities are believed to develop at inclusions; these cavities subsequently grow and coalesce by plastic flow until separation is complete. It is of interest to consider whether inclusions can affect fracture behavior under loading conditions which restrict the plasticity of the matrix itself (for example, cleavage under conditions of a high imposed strain rate at low temperatures). It is particularly interesting to study these effects in a solid which shows a spectrum of behavior ranging from fully ductile to semi-brittle behavior. Such a solid is silver chloride whose mechanical behavior depends sensitively upon temperature and strain rate.&apos;," The present paper is concerned with a study of the influence of inclusions (in the form of alumina particles) on the fracture behavior of silver chloride loaded uniaxially at low strain rates at room temper- ature and also under notch impact conditions over a wide range of temperature. In particular, it will be shown that the alumina particles can exert a startling effect on the ductile-brittle transition temperature of notched silver chloride and that the magnitude and nature of the effect depends upon both the quantity of alumina and the shape of the alumina particles. 1. EXPERIMENTAL PROCEDURE 1.1 Materials Used. Silver chloride powder of analytical reagent (AR) quality having an average particle size 6 was supplied by the Mallinckrodt Chemical Works (st. Louis, MO.). Acid washed 900 mesh alumina powder, designated A38-900, was supplied by the Norton Co. (Cambridge, Mass.). This powder was added to silver chloride in two forms: a) the as-received condition in which the individual particles were of random irregular shape; their statistical average size was 7; b) in a condition in which each particle was spherically shaped by a fusion technique. In this case, the statistical average particle size determined with the optical microscope was approximately the same (about 5p) but electron micrographic evidence indicated that many ultra fine particles were present in the spheroidized powder. 1.2 Preparation of Composite Materials. Silver chloride-alumina composites containing 2.5, 5, and 15 pct by volume of alumina were produced by the extrusion of mechanically mixed powders blended in a ball mill for 24 hr at room temperature. The mixtures were compacted at 50,000 psi at room temperature in the form of billets 3/4 in. in diameter and 1 in. long which were then extruded with a 16:l reduction ratio at 370°C through a radius-type steel die having a 5 deg lead-in angle. An extrusion temperature of 370°C was selected to ensure that all composites had sufficient plasticity to be extruded. Apart from this general requirement, the choice was arbitrary. 1.3 Microstructure of Composites. Attempts were made to check the distribution of alumina metallo-graphically by polishing transverse and longitudinal sections of the extruded rod. Specimens were wet-ground to 600 emery paper and lapped successively with 5 and 0.25-p grades of diamond paste. They were etched for 10 sec in 10 pct sodium thiosulfate solution and lightly polished in concentrated ammonium hydroxide. The most effective way to render the alumina particles and grain boundaries visible was to radiate the surface with intense white light to decorate the grain boundaries and the particle-matrix interfaces photolytically.

Jan 1, 1962

By Harvey Patashnick

Current state-of-the-art microweighing technology represented by the Tapered Element Oscillating Microbalance (TEOM) is utilized as the basis for a new generation of Personal Dust Exposure Monitors (PDEM&apos;s). Two design configurations are presented. The first is an end-of-shift analysis system which uses small TEOM-PDEM cannisters that replace the filter cartridges in the current PDEM system. All other components carried by the miner (cyclone preseparator and pump) are the same. After the shift the TEOM cannister is plugged into an interface box which enables a minicomputer to automatically identify the unit, determine the dust mass increase during the shift, compute the shift average dust mass concentration, and print out and/or store the data. The second design is a real-time TEOM-PDEM system which is capable of operation over a 10-hour shift and on demand display real-time dust concentration level, time weighted average, and shift average concentration. As a result of the design study, a prototype end-of-shift analysis system was fabricated and delivered to the Bureau of Mines. A description of this system which consists of six TEOM cannisters, interface electronics and minicomputer is given. The system represents a significant advance in the dust monitoring program in terms or accuracy and automation.

Jan 1, 1983

By J. Budac, E. Krause, C. L. Stewart, D. Wrana, S. W. Laundry

"As part of an over-all arsenic management strategy, Inco has developed a novel process that converts a by-product high moisture copper/arsenic sulphide precipitate into a crystalline copper arsenate suitable for the manufacture of wood preservation chemicals.The copper/arsenic sulphide precipitate is atmospherically leached with oxygen and sulphuric acid, producing a crude (blue) copper arsenate precipitate, elemental sulphur, and a copper and nickel containing solution. The blue copper arsenate is dissolved with sulphuric acid, the molar Cu/As ratio is raised to 2, and a crystalline copper arsenate (olivenite) is precipitated by the addition of sodium carbonate. Dissolved copper is recovered using metallic nickel (or matte) and elemental sulphur, to produce a low-moisture (low-arsenic) precipitate suitable for standard nickel-copper processing.The process was successfully piloted at Inco&apos;s Manitoba Division between September 1990 and June 1991. The copper arsenate product typically analyzed 43% Cu and 25% As, and the moisture content was about 10%."

Jan 1, 1995

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

By John E. Pahlman

An increasing number of gold and silver mining operations are employing cyanide solutions to effectively dissolve silver and gold from finely disseminated ores. Many of these operations use small, packaged processing systems like the State of Maine filter system, which employs zinc precipitation of gold and silver. Solution-clarifying filters in these systems become blinded with calcium carbonate (CaC03) scale and require frequent (every 2 to 10 days) dismantling of the filter units for acid cleaning, This is a hazardous operation as it is not compatible with the alkaline cyanide leach solutions and may result in the evolution of toxic hydrogen cyanide (HCN) gas during cleaning and during any accidental acid spill. The Bureau of Nines has investigated an alternative, nonacidic method of cleaning blinded State of Maine filters that employs ethylene- diamine-tetraacetic-acid (EDTA) type chelating agents to dissolve the scale. In situ cleaning of a 150-st/d State of Maine filters with EDTA- type chelating agents was successfully demonstrated. Greater than 90 pct of the CaC03 scale was removed in about 10 min with circulation of 31 L of 2.5-pct-EDTA solution through the filter unit. The EDTA cleaning method not only eliminates the cyanide hazard in filter cleaning but is advantageous from the standpoint of operating costs and productivity.

Jan 1, 1986

By J J. Batchelor, J B. Metson

Titanium (ilmenite) concentrate was extracted from a New Zealandilmeno-magnetite deposit. Tailings from the existing processing line at the Waikato North Head ironsand concentration plant were used as a raw material feed. The titanium bearing mineral extracted was defined as intergrowths of ilmenite and hematite in the size range below 150 um. The Owen-Honda equation was used to determine the conditions forilmenite/hematite magnetic separation. Three distinct regions of magnetic field strength for the mineral separation have been defined. Theoretical estimates from this calculation have been confirmed experimentally. Ilmenite concentrate was obtained using medium field magnetic andelectrostatic separation. The final material contains 40.6 - 42 per cent TiO2 and 39.1 - 39.8 per cent Fe (total). The actual yield from extraction was about seven per cent of the Zircon, leucoxene and monazite were found as byproducts of thetitanium concentration process. Preliminary experiments have shown the viability of industrial zircon benefication.

Jan 1, 2000

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By F. Weinberg

It has been suggested, for some time, that the behavior of metals under high-temperature creep conditions is strongly influenced by the behavior of the grain boundaries present in the material. This has led to a number of investigations1-6 in which attempts were made to measure the properties of the grain boundaries themselves, both to determine their contribution to the creep process and to obtain further knowledge of their intrinsic structure and properties. The present investigation was undertaken to extend the observed data under more closely controlled experimental conditions and to attempt to clarify sonie of the discrepancies in the literature. A brief report of the preliminary results has been published.7 EXPERIMENTAL PROCEDURE For the present investigation, controlled orientation specimens were used having plane boundaries which terminated at the specimen surface. Trierys-tal specimens were used instead of the bicrystal type of Puttick and King,&apos; in order to simplify the gripping technique required to apply a shear stress along the boundary. The aluminum used was obtained from the Aluminum Francaise and was of 99.994 pct purity, containing 0.002 pct each of Cu, Fe, and Si. The aluminum tricrystals were grown horizontally from the melt, in graphite boats, and in an argon atmosphere, following the technique developed by Chalmers.&apos; The orientation of the tricrystals was controlled by using seed crystals separated by mica inserts. Thermal conditions were adjusted to produce tricrystals having boundaries which were macroscopically straight, parallel to the growth direction, and perpendicular to the top surface. Following growth, the tricrystals were carefully cut with a jeweller&apos;s saw to the test specimen shapes shown in Fig. l(a) and l(b). In Fig. 1(a), the boundaries subjected to shear stresses are indicated AB and CD: Points A and C are the ends of the mica inserts separating the seed crystals; points B and D are at lateral cuts made in the specimen. It was found that the slots left by the mica inserts at A and C had to be enlarged slightly, by cutting, to ensure that the boundary terminated freely at these points. A shear stress was applied to the boundarks by gripping the upper two legs in file-faced Inconel grips and suspending a weight from the lower part of the specimen held in similar grips, as shown schematically in the diagram. The test specimens shown in Fig. 1(b) were cut from long

Jan 1, 1959