Search Documents

By James W. Ballard, H. H. Schrenk

"The X-ray method of quantitative determination is advantageous because it permits determination of compounds rather -than ions or elements; for example, the direct determination of quartz in silicates,4/,5/,6/ The method also takes into account the finest particles of a sample, which may be lost in wet chemical methods because of solubility or in petrographic methods because of limitation of the microscope. The sample is usually reduced to a powder and is easily prepared,7/ only a few milligrams of material being necessary. The sample and its chemical composition are not destroyed and may be used for further analysis by X-ray diffraction or by other methods.This paper presents in detail some of the more essential problems that arise in the application of X-ray diffraction to quantitative chemical analysis, Photometric measurements are discussed in connection with line intensities and the choice of X-ray film. The internal standard method, successfully used in spectrographic analysis, is applied.Copper K-alpha X-rays from a demountable research-type X-ray tube were used with a camera of 20 centimeters radius with a cast-lead-slit collimating system. A combination of a tilted wedge and a lead-slit collimating system permitted irradiation of a large amount of sample with X-rays. This tended to minimize errors due to possible inhonogeneity of the sample, to decrease the time of exposure, and to keep the lines on the X-ray film to a minimum width. There was sufficient dispersion of the lines for satisfactory analysis of most samples. Power was furnished the tube by a. source of constant high potential consisting of a synchronous motor generator furnishing 500-cycle power to a 100-kv. transformer, rectifying valves, and a condenser filter circuit. The X-ray tube was operated as a gas-type tube at 35 kv, and 20 ma,, the exposure times varying from 1 to 2 hours. The constant output of X-rays from the tube, indicated bar an exposure meter built for the purpose, was satisfactory.The recording microphotometer8/has been described. It was found preferable to a nonrecording instrument for measuring blackening of lines above a background on X-ray films. This background, which usually occurs, is sometimes complicated by numerous peaks from lines of complex diffraction patterns. is microphotometer record of the pattern, therefore, facilitates the location of the background 'and the measurement of the heights of the peaks and thus contributes to the accuracy of a determination."

Jun 1, 1946

By Laurence McGonagle

"The Highland Uranium Project (HUP) is located approximately sixty miles northeast of Casper, Wyoming and is owned and operated by Power Resources, Inc. (PRI). With an annual production of680 tonnes (1.5 million lbs) U308, HUP is one of the largest uranium producers by in-situ leach (ISL) in the western world. Uranium is currently produced from four wellfields with a total flow rate of approximately 1,135 m3/hr (5,000 gpm). The carbonate leach solutions are processed by anion ion exchange at two satellite facilities located in close proximity to the wellfields. The loaded resin is transported by truck to a central processing facility for elution of the uranium. Uranium in the pregnant eluant is precipitated and washed prior to calcining.Wastewater from the satellite facilities is treated and used for irrigation at a Land Application Facility. The wastewater generated at the central processing facility is injected into a 2,750 m (9,000 ft) deep waste disposal well.When economical mining of the orebodies is complete, restoration of the groundwater is initiated. There are currently two wellfields at HUP undergoing ground water restoration. Phase I restoration consists of removal of the carbonate leach solution from the ore body. Phase II includes treating the withdrawn fluid with reverse osmosis and reinjection of the permeate into perimeter wells.Future plans include construction of additional satellite facilities at the Gas Hills Project and other economical deposits located within 240 km (150 mi) of HUP. The capacity of the central processing facility will be increased to 1,815 tonnes (4 million lbs) U308 per year by late 1999."

Jan 1, 1998

By A. S. Argon, G. East

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By FRANK FIRRISTONE

Ix the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.' Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the dis¬trict, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Liirmann's cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons's furnace,2 for it appears from W. Firmstone's note-books that in October, 1840, he visited ." Gibbons' new furnaces building at Corbyn Hall," and I have an old drawing,\

Sep 1, 1909

By S. C. Gaillard

Tailings are made of ground rock that is left over from removing valuable minerals. The tailings are usually fine particles that cause environmental issues for storage and disposal. Disposal of tailings is a growing concern, as more tailings are produced from the increasing demand for mined material (ITRC, 2008). This project proposes a way to convert the mine waste to a useful product. Tailings were selected from a South Carolina crushed stone quarry, the products of which are used for road beds, sidewalks, asphalt and driveways. These tailings were processed to generate synthetic aggregates for construction applications. The synthetic aggregate creates a product that could be used for many purposes, including aggregate for sidewalks, driveways, roads and building materials. Testing methods followed the North Carolina Department of Transportation (NCDOT) guidelines for physical testing of coarse natural aggregate, which are sieve analysis, Los Angeles abrasion, absorption, specific gravity and soundness test. The synthetic aggregate produced passed all tests for NCDOT and, in some instances, rated better than a natural aggregate. Using the tailings from the crushed stone and mining industry would convert the waste into a valuable, marketable product.

Jan 1, 2013

By R. W. Lake

The decision to develop an ore body can lead to multi-million dollar profits, or equally substantial losses. Accordingly, the effort required to adapt a valuation model to the specific proposal at hand, or even the development of a new model from basic principles, is clearly warranted. In the formulation of a model of this nature, one is faced with some major questions. For example, with the long term obligations that it implies, on what basis should a decision to initiate mining operations be made? Furthermore, how can the vagaries of inflation and the uncertainties that shroud the future be accommodated? Beyond the general principles by which mineral deposits are evaluated, specific cost behaviour is a function of the geology of the deposit, and of the mine design. Moreover, mine design, during the life of the mine, must be a continuing process somewhat akin to dynamic programming. An initial, apparently optimal, design is selected and mining commences. With production, a continual process of information updating leads to revisions. Thus if the maximum value is to be obtained, the mine design must be adjusted to conform to the changed conditions.

Jan 1, 1977

By AMIRA P588 Research Team

This contribution summarises new knowledge and data, obtained during a three year ARCAMIRA funded research project, on the mineralogical and geochemical characteristics of hydrothermal alteration associated with low sulfidation, gold-silver epithermal deposits. These data are used to develop exploration vectors for use at both deposit and district scales, plus techniques have been established to distinguish ore grade epithermal systems from barren or low grade systems. Deposits investigated were Ladolam, Papua New Guinea, Gosowong and Mt Muro, Indonesia, Cerro Vaguardia, Argentina and Bimurra and Twin Hills, Australia.

Jan 1, 2005

By Alan J. Zeni

Drainage of water from abandoned underground mines has become important in recent years because of safety concerns when mining near abandoned works or reentering abandoned mines for further development. Seepage from inundated mines causes environmental damage and may threaten homes and communities. Where topography permits, horizontal drilling can provide a quick and cost effective method for solving trapped water problems. The mechanics of the horizontal drilling operation as applied to water drainage are discussed in this paper.

Jan 1, 1990

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By C. A. Young

Cyanide is a fast-acting, highly toxic substance but, at the same time, is deemed essential for sustaining life as well as our standard of living. In this manuscript, the facts about cyanide are presented beginning with a brief history and definition and ending with a discussion on cyanide alternatives. Other topics include speciation, physical characteristics, toxicity, manufacturing, cyanogenics, cyanide cycle, separation, destruction, and markets including those outside the mining industry. Emphasis, of course, is placed on gold production by leaching and how it is influenced by ore type, mineral characteristics and economics as well as its advantages and disadvantages.

Jan 1, 2001

By Juan Estrada, Mirtha Frómeta, Rubén Alcalá, Emilio Montejo, José Castellanos, Juan Berto, María Rivas

"The oxidized nickel ores from San Felipe deposit are composed mainly Smectites which gives to the pulps very unfavorable rheological .properties (cinematic viscosity and high shearing strength) for transportation processes (pumping), very low settling velocities and very low thickened pulps. These properties do not allow the preparation of high % solids, which affects the economic efficiency if a high pressure acid leach (HPAL) process is used. Pulps of close to 30% solids have very high BYS making pumping impossible. CIPIMM developed three technologies to solve these problems and to substantially increase the % solids in the pulps to be leached without a thickening step. These technologies are: • CIPIMM 2. At Preparation of pulps using additives. This method is based on the effect of some additives (inorganic salts) to improve the pulp’s properties. The use of this method allows increasing the % solids in the pulp up to 40% with good rheological properties • CIPIMM 2B. Preparation of pulps by thermal treatment of the ore previous to the preparation of the pulps. This method is based on the thermal destruction of the clays structure. Its use allows to obtain pulps with 50 - 60 % solids with excellent rheological characteristics. As a collateral effect, the Ni and Co grades increases by 10 - 15%. • CIPIMM 2C. Pulp preparation by chemical treatment. This method is based on the chemical transformation of clays, to obtain without thickening, pulps with 43- 45% solids and excellent rheological properties. The use of one of the three technologies depends on the chemical and mineralogical composition of the ores and the results of technical-economical evaluations to determine which one is the best alternative before running higher scale tests."

Jan 1, 2014

By A. Wahab Khair

Coal mining has evolved into extensive use of continuous mining machines for development and production. This has resulted in an increase in dependence on the versatile continuous miners. The present-day continuous miners are powerful in terms of rated power but are still plagued by wear of bits which hinders development and production as the bits have to be continuously changed at regular intervals. Previous attempts to analyze bit wear has been either restricted to the theoretical approach and or laboratory testing. This paper discusses about the overall aspect of bit and drum design for different conditions. Using the laboratory model set up, numerical models and field testing, a new bit and drum design was analyzed to evaluate their performance under different conditions. The results proved that a newer bit design and drum design were successful in limiting the amount of wear as well as improving the performance of the continuous miner and production.

Jan 1, 2008

By A. C. Stevenson

"The most common theory is that, since thyristors, diodes, and insulated gate bipolar transistors (IGBTs) are “solid state” they will live forever. This is not so. They have wear-out mechanisms (e.g. insulation) and other mechanical parts such as motor bearings. These wear-out phenomena can be easily calculated. In this paper we will look at some of the failures and the failure rate of thyristors in power converters to see what affects them and to see what improvements can be made. If converter failures do occur, some simple forensic engineering steps will show if this is the root cause of the problem.IntroductionLook at the general failure rate curve for thyristors, diodes, gate turn off devices (GTOs) and IGBTs shown in Figure 1. We see that there is an initial high failure rate due to manufacturing defects, application problems, and drive start-up stresses that lasts for a few weeks. This is followed by a long period of (hopefully) several years with a relatively low but very slowly rising failure rate. At the end of this period, the devices start to wear out and the failure rate suddenly starts to increase rapidly over a few months. This signals the end of life for the devices in the system. We will start by looking at this end of life area."

Jan 1, 2000

By James Cornwell, John A. Elton

"Thermionic induced reactions and radiation resonance catalysis of aluminum and aluminum oxide materials exposed to microwaves and triboemissions will be described and explained from both a fundamental and practical level. Magnetron operation at distinct operating conditions that generates both plasmon and triboemissive radiation will be explained and the resulting tribochemical and radiation resonance catalytic reactions between aluminum, aluminum oxide, water and graphite will be delineated. The generation of hydrogen from these materials using triboemissive radiation and microwaves will be described, and the application of this methodology for hydrogen based technologies will be discussed.IntroductionProtective Systems Directed Energy RadiationProtective Systems, Inc, has developed a new radiation device called the EMR (Electromagnetic Resonator) that has unique characteristics that separates it from traditional microwave and rf radiation devices. The radiation from the EMR device is generated using a modified electronresonance magnetron with proprietary filters and operating characteristics.Electronic Device Shutoff. When electronic devices such as cell phones, computers, and other IC based electronics are placed within the EMR radiation, these devices become non-functional as long as the EMR beam is active. Upon removal of the EMR radiation the devices either become operational again or become operational after a cold start. The devices are not damaged by the irradiation.Faraday Cage Interaction Effect. When any of the above electronic devices are placed in a Faraday cage and activated within the Faraday cage without EMR radiation, they operate normally. However, these devices will still be rendered inoperative when an EMR beam generated outside the Faraday cage is directed at the electronic."

Jan 1, 2010

Capture airborne respirable dust generated by an auger-type continuous mining machine to reduce workers' dust exposure. Approach Install a water-powered scrubber system, operating at 1,400 psi, on the sides of the conveyor. The scrubber draws the dusty air from the face area and discharges cleaned air into the face return. How It Works Auger-type continuous miners pose unique ventilation and dust control problems. To protect face workers from the dust, the end of the brattice is usually maintained close to the face to increase ventilation effectiveness. However, it is taken down as the machine cuts toward the exhaust side to allow the machine to complete its cut. Often, the brattice is not reinstalled in a position to most effectively control

Jan 1, 1989

By Jan E. Nesset, James A. Finch, Frank Rosenblum, Rebecca Payant

"Under certain conditions of moisture and oxygen, sulphides can spontaneously heat, a phenomenon known as self-heating. In this paper, we test a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by restpotential difference between minerals and their surface area of contact (particle size). In order to decrease rest-potential, four sulphides were tested: pyrite, chalcopyrite, sphalerite and galena. Two series of samples consisting of mixtures of two sulphides, each representing a mass fraction of 50 %, were run in standard self-heating tests. The first series comprised five mixtures, two with low rest-potential difference (pyrite-chalcopyrite and chalcopyrite-sphalerite) and three with high rest-potential difference (pyrite-galena, chalcopyrite-galena and pyrite-sphalerite). The second series was performed on a pyrite-sphalerite mixture at four particle sizes (80 % passing 850 µm, 300 µm, 75 µm and 38 µm). The first series showed that the individual sulphides and the mixtures of low rest-potential difference did not self-heat but the mixtures of high rest-potential difference did self-heat. The second series showed that self-heating increased inversely with particle size (increased specific surface area) and revealed that it was the fineness of the pyrite (high rest-potential sulphide) that governed the self-heating effect, indicating the rate-limiting step is the reduction reaction on pyrite (cathodic mineral). The increase in self-heating with high rest-potential difference and increasing particle fineness supports the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on the hydrogen sulphide hypothesis is proposed where the reduction reaction at the cathodic mineral surface is ferric to ferrous. The understanding gained will be of interest to those involved in storage, shipping and disposal of sulphide minerals.INTRODUCTIONSulphide mineral ores are the major source of most base metals such as copper, zinc, nickel and lead. Once the ore is extracted, the sulphide minerals are liberated by size reduction (crushing and grinding), concentrated by flotation, and the concentrates sent for further processing to extract the metal (smelting and refining). At the various stages from mining to concentrate shipment and tailings storage, the sulphides are exposed to a variety of environments, which under certain conditions of air (oxygen), humidity and temperature can cause them to heat. Since no external heat source is involved, this pyrophoric process is known as spontaneous heating or, more commonly, self-heating. The self-heating of sulphides is associated with oxidation reactions under moist conditions. If the heat generated is greater than the heat dissipated, the sulphides will self-heat and the material temperature will rise. This can make working conditions potentially dangerous as oxygen is consumed from the surrounding air and significant quantities of sulphur dioxide (SO2) can be released (Ninteman, 1978)."

Jan 1, 2011

By Patrick K. Wong, Richard Kelly

"The variability in strength and compressibility of in situ deep soil mixing products can be greater than the variability of the natural soil. However, satisfactory performance can be achieved by careful construction and an appropriate QA/QC program. This paper presents a case study on the use of deep dry soil mixing columns to support several embankments over soft clay along a highway project. Post-construction settlement monitoring indicated that good performance is achieved where the acceptance criteria are met, except in an area with high organic content. Embankments with contrasting performance are compared to the quality control test results which comprised laboratory testing of core samples as well as in situ test results such as pull-out and push-in vanes and conventional cone penetration tests. Drawing on the performance results and quality control testing, discussions and guidelines are given on quality assurance acceptance criteria and construction control testing regime for future projects.INTRODUCTIONBetween 2008 and 2012, the largest deep dry soil mixing (DSM) contract during that time in the southern hemisphere was carried out for the Ballina Bypass project. The project, comprising 12 km upgrade of the Pacific Highway located in northern New South Wales close to the border of Queensland, was commissioned by the Roads and Maritime Services (RMS) of NSW. The ground improvement contractor was Keller Ground Engineering (KGE) Australia. Seven different types of ground improvement techniques were employed for the project, ranging from low embankment strategy with nominal preloading, to surcharge with wick drains, light weight bottom ash fill, DSM, vibro-replacement stone columns, dynamic replacement, and vacuum consolidation (installed by Menard Bachy Pty Ltd). Different techniques were chosen depending on time program, cost, and performance requirements relative to proximity to piled structures (e.g. bridge abutments) and post-construction settlement and differential settlement for either rigid or flexible pavements at different locations.DSM was the most utilized ground improvement technique employed on the project, comprising a total of about 285 km of 0.8 m diameter columns to depths up to 18 m for the purpose of supporting bridge approach embankments and culverts with embankment heights up to 6 m. DSM was chosen due to the very soft nature of the clay soil with moisture content practically at liquid limit, and the relative speed and economy of the system. Dry cement powder at rates of 160 kg/m3 to 200 kg/m3 were pneumatically discharged via the hollow stem of the mixing tool, and mixed with the soil (using multiple horizontally mounted paddles on a single vertical stem) at high speed as the mixing tool is withdrawn."

Jan 1, 2015

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By C. O. Swanson

Introduction It is thirty-odd years since I first entered the mining field by working underground at Anyox, which makes 1t clear that I can qualify as one of the older generation and claim the privilege of dealing in generalities and broad impressions. In this position I find it interesting to re~ view the salient changes that have taken place during the past quarter-century and indulge in some speculations concerning the future, with the hope that my comments may be of value to others engaged in the field of mining geology. As indicated by the title, the treatment is a perspective from a single viewpoint rather than an attempt to give a complete and impartial analysis. This plan, while deficient in some respects, has the advantage of being more specific than one based on .a. compilation of opinions. An additional advantage is brevity, which would be difficult to obtain on a subject of this scope if it were viewed from all angles. In conformity with the general plan, specific references to the literature have been avoided as much as possible, although a number of publications of general nature are listed at the end of the paper. This procedure is intended to give credit to the sources used without making them in any way responsible for the interpretation. The starting point for the discussion is the situation as it existed twenty-five years ago, when, as a recent graduate, I first had a fairly complete picture of it. However there is one impression of an earlier; stage that seems worth mentioning. In one of my first courses in geology the statement was made that some of the leading authorities of the previous generation, who guided geological thought at about the beginning of the century, were inclined to question the value of an association with mining. This attitude was no doubt exceptional, and certainly it was not adopted by the students who laid the groundwork for mining geology in North America. But its existence even in a limited circle is significant m showing how far the application of geology has advanced as the result of the investigations started during the first part of this century.

Jan 1, 1949

By J. P. Kennedy, O. A. Bascur

Large metallurgical complexes have more data than a small city and these data change as internal and external conditions evolve. Staffing turnover hinders experienced-based decisions especially with simple tools like spreadsheets. Lack of current information can contribute to decisions that result in significant deterioration in the quality of operation. Timely, unified information from sophisticated analyses presented to the broadest possible reach will improve operation. The major innovation is the addition of the web browser to the suite of software people will use with no training – the other two are spreadsheets and graphical presentations – and the consistent organization and transformation of the real time data to support broad access. This paper describes the data transformations and presentation methods necessary for a Web view, especially the special needs of real time data and analysis required for active operations decision-making. Many people inside and outside the complex, not just operators, need timely information that is abstracted, aggregated, organized and unified. Unification and aggregation of real time data presented via the Web opens a new paradigm for collaboration. The analysis tools are as important as the data. These rule-based tools add significantly to the operations database in the form of results stored for viewing with plant data. Mining and metallurgical plants already use many sophisticated analysis tools such as predictive maintenance policies based on statistical analysis vibration analysis, and oil and lube analysis for critical equipment. These add real time events, similar to an alarm package, and unified production information to the operational database. Simple models are used on line to create key indices that provide a real time indication of performance. Key indices include metrics for losses due to plant availability, performance efficiency, and overall process equipment effectiveness. These additional data in the operations database are used for early fault detection, increased production, better quality, higher availability of equipment and faster detection of process bottlenecks. An important feature is the ability for people to create their own key indices and store the results for use by anyone in the plant historian, but accessible by a browser. Keywords: plant information, principle components analysis, data reconciliation, gross error estimation, Internet, Word Wide Web

Jan 1, 2002