Search Documents

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By David Norval

Water solidification of mattes, metals, alloys and certain slags with high metal entrainment has customarily not been practiced due to the belief that such processes are too dangerous and unproven in the Pyrometallurgical Industry. Slag granulation on the other hand is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. This paper will examine the most common air solidification processes and compare such processes with water solidification, mainly slag and matte granulation processes and design criteria for safe and reliable operation. Finally, purpose designed granulation and solidification processes will be discussed taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte or alloy responds in similar fashion to a granulation practice.

Jan 1, 2006

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby's pole mechanism are discussed in detail by Venables.' In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024

Smart defense: that?s what the industry needs to play for the next four years, according to panelists at the 118th Annual Meeting of the Northwest Mining Association (NWMA), which met December 2-7 in Spokane, WA. The conference was well attended, with approximately 2,200 attendees, 244 booths in the two packed exhibition halls, and a rich offering of short courses, field trips, social events and technical sessions. Speakers at the packed legislative session articulated many of the frustrations felt by members of the mining community after the U.S. elections in November, and offered words of advice. Matthew Ellsworth, the new Government Affairs hire at NWMA, stated it best: ?Elections are like Christmas: you find out who?s naughty and nice ? and it?s always going to come again.?

Jan 1, 2013

By L. L. Oden

The U.S. Bureau of Mines and the Department of Energy (DOE), through its contractor EG&G Idaho Inc., are collaborating on a multiyear research project to evaluate the applicability of three-phase, electric arc furnace melting technology to vitrify materials simulating low-level radioactive and mixed wastes buried or stored at the Idaho National Engineering Laboratory and other DOE sites. The melter is a sealed, 1-t (1.1-st), three-phase, 800-kV?A electric arc melting furnace with 10.2-cm-(4-in?) diameter graphite electrodes, water-cooled roof and sidewalls, and four water-cooled feed tubes. A water-cooled copper fixture provides for continuous tapping of slag. An instrumented air pollution control system (APCS) with access ports for analysis and a feeder based on screw conveyors and a bucket elevator are dedicated to the facility. Test data are provided by an arc furnace analyzer and by sensors indicating feed rate; slag temperature; and temperature, pressure, and velocity in the APCS. These data are received by a data logger, digitized, and transmitted to a personal computer for storage and display. This unique waste treatment facility is available for public and private use on a cost-sharing basis.

Jan 1, 2010

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By Adrian Coombs

The York Durham Sewage System (YDSS) Interceptor Tunnel Project is located in the Town of Richmond Hill, Ontario, Canada, just north of Toronto. Construction commenced in September 2006 and completion is planned for early summer, 2008. The project involved public and agency buy-in of construction technologies and methods that minimized dewatering, design and construction of sealed shafts with jet grout break-in and out blocks in order that Earth Pressure Balance (EPB) mode could be maintained by the Tunnel Boring Machine (TBM) during shaft entry and exit. This paper will discuss the advances that were made possible through the opportunity to apply and test these technologies in order to accommodate the aquifer and artesian conditions present on this project.

Jan 1, 2008

By F. W. Lee

List of GEOPHYSICAL ABSTRACTS

Jul 1, 1932

I. Domestic Production and Use: In 1981, 13 companies operated 32 primary aluminum reduction plants, with 3 firms accounting for 58% of production, Washington, Oregon, and Montana accounted for 32% of the total production; Texas, Louisiana, and Arkansas 16%; Tennessee, Alabama, South Carolina, and North Carolina 17%; other central and eastern States 35%. Based on published producer prices output of primary metal in 1981 was valued at over $7.5 billion. Aluminum consumption by 25,300 firms was centered in the East Central United States. Packaging accounted for an estimated 30% of domestic consumption in 1981, building 21%, transportation 18%, electrical la%, consumer durables 8%, and other uses 13%

Jan 1, 1982

By Holt L. Farley

This report describes the development of an electronic system which detects unsafe slack and overload conditions in underground mine hoist ropes. The Slack and Overload Rope Protection System (SORPS) includes a fail-safe load cell inserted between the rope and the conveyance, and an accelerometer mounted on the conveyance. Signals from these transducers are telemetered via a radio link to the hoist control room, where they are combined with drum speed and chair status in a microprocessor-based decision and display unit. Abnormally high external force levels are detected as discrepancies between rope tension and cage acceleration; conveyance weight is inferred continuously. Hazardous conditions are displayed to the hoist operator, along with general hoist status. The system has been tested in a working mine for approximately two years. The report contains specifications, design data and field test experience generated under the SORPS program. It also includes information on dynamic modeling, vibration environment, the status of existing slack detection systems, and applicable control strategies.

Jan 1, 1983

By J. R. Goode

Up to one half of neodymium and praseodymium production, key ingredients in permanent magnets, is produced illegally. About 60% of cobalt production, critical in lithium-ion batteries and other applications, comes from central African states, and much of it is produced illegally. Tantalum, important in modern electronics, is also primarily sourced from central Africa and, again, much of it illegally. Illegal mineral production, as exemplified here, is often used to fund armed conflict. Furthermore, it is typically conducted with scant regard for human rights and environmental protection. It also leads to depressed prices which in turn limits the possibility of legitimate producers entering the market. Systems of traceability and provenance, along with cooperative supply chain participants can limit the production of illegitimate material and thereby improve conditions in the countries of origin and reduce downward pressure on prices.

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

The investigation and uptake of filtered tailings continues to grow around the world, but cost and scalability are deterrents for mining companies. Filtration technology that is currently in use is unable to meet the needs of many operations and projects that would otherwise adopt filtered tailings. For tailings to reach the desired moisture content for dry stacking, the majority of processes require pressure filtration, with significant upfront and ongoing maintenance costs. Given the comparative lower costs associated with low-pressure Viper vacuum belt filtration, this technology has the potential to alleviate dependency on high-pressure applications and make efficient dewatering and handling of tailings a more economic and sustainable solution.

By M. H. Attia

The concept of sustainable development has been evolved into a working framework for sustainable manufacturing, in which the environmental requirements are introduced into product development at the design stage. This keynote paper is discussing a number of issues pertaining to the impact of manufacturing on the environment. The conflicting requirements of sustainable development, sustainable manufacturing (SM) and economical growth are presented in the light of successful case studies that were able to convert conflicts into opportunities. Integration of SM into the product life cycle is also presented. A number of concepts that are related to Ecoefficiency, e.g., inverse manufacturing, demanufacturing and re-manufacturing are also discussed. The paper underlines the fact that the positive impact of this new philosophy is equally applicable and beneficial to both; developed and developing countries. The paper concludes with an overview of Global trends in environmentally benign manufacturing (EBM); e.g., product-take back and emerging material and processing technologies. The state-of-the-art approach to Life Cycle Impact Assessment and integration of design for the environment DfE principles are demonstrated through some case study.

Jan 1, 2006

By A. P. E. Dirige

Extensive field study has been performed to assess the capabilities of thin sprayon liners (TSLs) and conventional spray-on support systems for preventing rock and support material damage that often results due to mining-induced rockbursts. Support performance was studied using field scale explosive detonation trials to simulate dynamic failure effects that are known to develop during typical rockburst events. Multiple seismic and high speed photographic monitoring techniques were used to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion, and support liner survivability characteristics. Results of this study have demonstrated that TSL?s and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In this study, field results have been verified using numerical modeling procedures to better understand the support behaviour of TSLs when subjected to highly stressed mine environments and mining-induced rockbursts, a factor that is essential when designing any rock support system. A series of numerical modeling assessments were conducted using FLAC3D modeling of a half circular TSL-lined tunnel, influenced by anisotropic stresses and simulated mining-induced rockbursts, to investigate the support potential of TSLs under prototype conditions. The effect of a mine rockburst was simulated using the three-dimensional dynamic analysis option of FLAC3D. Results of TSL-lined tunnels in highly stressed and mine rockburst conditions indicated exceptional effectiveness of TSLs for suppressing rock deterioration resulting from stresses and rockbursts. The rock support potential of TSLs on tunnel surfaces was compared with that of thin shotcrete linings, and results indicated that thin spray-on lining products currently available may be equally as effective in support as shotcrete materials.

May 1, 2009

By André Vervoort

After the systematic closure of Europe’s coalfields in the late twentieth century, the emphasis is now clearly on industry’s environmental legacy. One aspect of the latter is the longterm surface movement above abandoned coal mines. The analysis of satellite data shows that the subsidence lasts longer than generally assumed. However, a few years after the flooding of the abandoned underground coal mines, a new phenomenon was observed, i.e., the direction of the surface movement was reversed. The phase of upsidence has already lasted for several decades, and only future measurements will tell how long it continues. A key conclusion is that the regions with maximum subsidence do not necessarily correspond to the greatest upsidence. In other words, buildings and infrastructure are subjected to a different loading from this upsidence than during the subsidence phase. The longterm surface movements have an impact on vulnerable structures in the densely populated regions of the former deep coal mining areas in Europe. These movements create additional damage. This new knowledge is also relevant for mines that are still in operation or future mines that are planned.

Feb 1, 2024

By T. A. Klinefelter

ONE OF THE many services rendered by the Federal Bureau of Mines is the identification and general examination of ore and mineral samples. Many of these, coming from almost every State in the Union, are clay and shale samples. Other Government agencies, State geologists, universities, and other laboratories are often requested to make similar examinations. This publication describes methods of testing these samples. An earlier paper, published in 1943, described Bureau of Mines methods of testing such clays.3 This paper was to be followed later with another (part II) that would describe much more thorough testing than did the rather general outline of part I. Part I has been out of print for some time and needs revision, and part II was never written; hence, the present publication is designed to include part I and also those additions intended as part II. The tests presented in part I were simple, requiring only the ordinary equipment to be found in any good chemical laboratory. The second publication was to include a greater number of test procedures and information on increasing the accuracy and precision of those previously given.

Jan 1, 1957

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By Carlos León, David Estrella, Javier Linares

"Recently, Antamina has completed an expansion program of its operations which increased the thoughput in grinding from acapacity of 109 to 130 ktpd. After commissioning, throughput could be exceeded in grinding and downstream processes but primary crushing became a major bottleneck to the overall production process.With an objective to increase the processing capacity of the primary crusher system, a multidisciplinary team was formed with members of Mine, Concentrator and Maintenance departments, who analyzed the overall context of this process restriction. The main implementations developed were: automatic discharge systems of trucks, logic to count trucks and elaboration of a daily performance report. Following implementation of developed improvements, the numbers of discharged trucks to crusher were increased from 449 to 614 units per day. As a result, the expansion target of 130 ktpd was exceeded and processing capacity was increased from 109 ktpd to 145 ktpd. This improvement adds very significant economical value for Antamina.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and had a nominal 77,000 ktpd mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper and zinc, concentrates are transported by pipeline down to the port of Huarmey. Molybdenum and lead-bismuth concentrates are bagged and trucked to port."

Jan 1, 2013