Search Documents

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By Daniel A. Thome, Robert C. Janke

"Installation of permanent soil nails through distressed mechanically stabilized earth retaining walls is a cost effective and aesthetically pleasing solution when using the appropriate equipment and drilling methods for installation. A forensic investigation was performed on an existing mechanically stabilized earth retaining wall to determine the possible causes for the excessive horizontal displacements and visual structural flaws found along a portion of the wall. Reports concluded that the visual shifting was due to a number of factors including improper drainage in the vicinity of the wall and unsuitable compaction of the backfill material. Conceptual designs were proposed to the owner and the installation of permanent soil nails through the existing precast panels was determined to be the most practical solution. A total of ninety-three permanent soil nails were installed to lengths of up to 40 feet (12 m) through sand backfill and silty day fill using a hydraulic rotary percussion drill attached to a tract mounted excavator.IntroductionThe Illinois State Toll Highway Authority awarded Contract RR-03-5144 in the summer of 2004. Construction work for the project consisted of the rehabilitation of two existing concrete culverts and approximately 100 linear feet (31 m) of mechanically stabilized earth (MSE) retaining wall. The retaining wall is located below the southbound lanes of the Tri-State Tollway near the intersection of Federal Highway 41 in Wadsworth, Illinois as shown in Figure 1.Reports were prepared by Applied Technologies in cooperation with Giles Engineering Associates to determine the condition of the MSE wall and recommended conceptual designs to extend the service life of the wall.Nicholson Construction Company (Nicholson) wasselected as the design-build geotechnical subcontractor to install the recommended permanent soil nails through the existing precast concrete panels of the MSE wall. Rehabilitation of the wall involved the installation of ninety-three permanent soil nails through the existing wall, along with soil nail verification tests and proof tests on production nails."

Jan 1, 2005

By Ricardo Dobry, Alain Pecker, George E. Leventis, Ralph B. Peck

"This year’s DFI Outstanding Project Award is for the design and construction of the foundation scheme for the largest cable-stayed bridge in the world. In 1993, Gefyra, SA (a French/Greek consortium led by VINCI of Paris, France) was awarded a €750 million ($1billion+ USD) Concession Contract to design, build, fi nance, operate and maintain a three-span cable-stayed suspension bridge connecting the Peloponnese, Greece’s southernmost peninsula, with the mainland across the Gulf of Corinth. The contract extends over a 42-year period, 7 years for design and construction and 35 years for operation. The project was fi nanced through a combination of public funds, private equity and bank loans. Alternative foundation concepts that were considered included traditional driven piles, deeply embedded caissons and soil improvement. PROJECT CHALLENGESThe extreme technical challenges faced included:??Weak foundation soils composed of soft alluvial deposits consisting of interbedded layers of granular and cohesive materials with thin layers and lenses of gravel and liquefi able sand pockets; rock is believed to be at a depth of 1,000 m (3,500 ft) or more.??A very deep seabed exceeding 60 m (200 ft).??The requirement to withstand the collision of 180,000-ton tankers traveling at 16 knots.??Maximum wind forces of 250 km/hour (155 mi/hour).??Design seismic forces corresponding to Richter magnitudes of 7.0+ with peak ground accelerations of 0.48 g at seabed.??Design tectonic movements of 2 m (7 ft) in any direction between any two adjacent bridge pier foundations/pylons.Considering subsurface conditions and local seismicity and water depths, foundation design and construction methods were the key drivers for this project. In large part, the success of the project is owed to the unprecedented partnering and collaboration between all partners involved fostered under the leadership of Jean Paul Teyssandier and Gilles De Maublanc of VINCI Group (France) who served as lead Concessionaire and General Contractor. The joint venture’s lead Greek partners were Elliniki Technodomiki/AKTOR and J&P/AVAX. Alain Pecker of Geodynamique et Structure (France) served as lead Geotechnical Consultant/ Designer while Buckland and Taylor (Canada) served as Design Checkers with Ralph Peck and Ricardo Dobry (U.S.) as Special Advisors on foundation issues, Langan International/Langan Engineering and Environmental Services P.C. (George E. Leventis, Gregory Biesiadecki and Diane Fiorelli) served as Technical Advisor on geotechnical, geodynamic and foundation/marine construction issues."

Jan 1, 2007

By George M. Fowler, J. P. LYDEN

T HE relationship of geological structure to orebodies and to the great masses of chert in the Tri-State mining district is of such significance that it prompts a brief recital of the existing information regarding the various periods of structural deformation. We began to note a relationship between structure and orebodies early in our studies of the field, and further work revealed a like relationship of structure to the great masses of chert so commonly associated with the ore-

Jan 1, 1934

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By Lyn Jones, Mike Bratty, Rick Lawrence, David Kratochvil

"The treatment of water is required at many mining operations to remove metals and prevent the discharge of contaminated water to the environment. In other cases, water treatment is used to provide better quality water for recycle to the processing plant, or to process bleed streams in hydrometallurgical operations in order to prevent deterioration in metallurgical performance or process equipment. BioteQ Environmental Technologies Inc. has developed and commercialized the BioSulphide® Process which can provide an alternative for these treatment needs and which can also be used for profitable metal recovery, particularly in cases where conventional metal winning techniques are not economical. The BioSulphide® Process is a high rate anaerobic biotechnology for on-site production of H2S from sulphur species, although for smaller flows and metal loadings, the use of chemical sulphide reagent might be more cost effective. Both new projects and existing commercial operations, used for removal and/or recovery of copper, nickel, and zinc, and which range in sulphide generating capacity from 50 kg/day to 3.7 tonnes/day, are discussed. Particular focus is placed on the results of operations at the Raglan Mine in Northern Quebec where dissolved nickel is removed from contaminated water at a high efficiency through the precipitation of nickel sulphide. Plant effluent is discharged directly to the receiving environment and the high-grade nickel sulphide product is combined with the nickel flotation concentrate produced at the mine. The plant at Raglan will replace the existing conventional water treatment plant and will eliminate the need for on-site storage of treatment plant sludge.INTRODUCTIONThe BioSulphide® Process, which produces low cost H2S for use in selective metal precipitation, offers a low capital cost alternative which can operate efficiently and cost-effectively within a wide range of flows and solution grades. Since the technology can be used to recover metals from solutions with low flows and metal grades, the technology is also applicable to environmental applications for water treatment, with the sale of recovered metals providing an offset to treatment costs. For environmental control, the technology has a distinct advantage in being able to meet strict effluent discharge criteria due to the very low solubility of metal sulphides. To date, BioteQ Environmental Technologies has designed and constructed three plants for metal sulphide precipitation, with another three projects in the advanced development stage."

Jan 1, 2006

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

By Priyadharshini M. R., Premalatha K

"Abstract With the development in the construction of heavily loaded structures, the necessity of pile foundations has increased. For the transfer of heavy loads, it is mandatory that the piles need to be socketed in the underlying rock strata. The load transfer in bored rock socketed piles is by end resistance or the combination of shaft and end resistance which in turn depends on the length of the rock socket. The determination of socketing length of the pile at present is mostly based on a few factors which affect the pile load transfer mechanism. The effect of all the possible factors involved, need to be studied in proposing guidelines for the design of rock socketing length of the pile. Analyses are carried out using finite element analysis software (PLAXIS 3D Foundation) to understand the influence of the thickness of overlying strata for different socket lengths of piles in weak rock. From the load settlement curves, the influence of the overlying soil on the rock socket length isobserved and an effective rock socket length is proposed.IntroductionThe determination of socketing length of the pile at present is mostly based on a few factors affecting the pile load transfer mechanism, which sometimes give a better design and sometimes an uneconomical design. Too much socketing length results in more construction time and higher costs. Therefore, the effect of all possible factors involved need to be studied in proposing guidelinesfor the design of t h e r o c k socket length of the pile.The factors that affect the termination criteria of the rock socketed pile are the capacity requirement, thickness and properties of the overlying soil, characteristics of the founding strata, drilling tools used, roughness of the rock socket and nature of loading.A comprehensive study was performed to understand all the above mentioned factors in different types of rocks. In this paper discussion is made on the settlement results, specifically the influence of overlying sand of different densities above a weak rock. The influence of stress developed is not discussed, keeping in mind the size of the paper under study."

Jan 1, 2014

By Arnold B. Hubbard

This report presents a hydrogenolysis study undertaken to obtain information on the constitution of the kerogen or organic material in Colorado oil shale and to determine some of the properties of the hydrogenolysis products. The high yield of hydrogenolysis products was separated, so far as possible, into type compounds; a number were identified. The results thus obtained were used as a basis for proposing the possible existence of certain structures in kerogen. To the authors' knowledge, few or no hydrogenolysis studies have been made of Colorado oil-shale kerogen by others. However, this method has been used in studying the constitution of coal. In general, the coal studies involved treating pulverized coal at different temperatures and hydrogen pressures with different catalysts. In some instances different solvents were used during the treatments.

Jan 1, 1959

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

By José Arce

El sistema AG-DAS entró en operaciones en 2015 y su aplicación tiene diversas ventajas sobre el método de polarización inducida convencional. El concepto del sistema fue el uso de múltiples receptores de dos canales, que registran la señal completa con sincronización de tiempo por GPS. La tecnología DAS (sistemas de configuración distribuida, por sus siglas en inglés) brinda mayor confiabilidad en la detección y modelamiento tridimensional de mineralización metálica con geometría compleja a profundidades de hasta más de 800 metros.

May 22, 2019

By G. A. Pinsky, Pickard M. K

"IntroductionTWO METHODS of mucking have been used in sinking C shaft, the five-compartment production shaft of the Yellowknife property of Giant Yellowknife Gold Mines, Limited:(a) Band mucking during the original sinking in 1949 and 1950 (l); and(b) Mechanical mucking with the Cryderman shaft mucker during the recent deepening in 1954.This paper briefly describes the recent deepening and compares the performance figures of the two sinking operations.PlanningProduction planning in 1952 showed that it would be advisable to deepen C shaft in 1954 to provide for three new production levels and the installation of an underground crusher. To complete the required shaft work it would be necessary for a shaft crew to deepen the shaft about 500 feet, to partly excavate three level stations and a crusher station, and to cut a station for the loading pocket. Figure 1, a vertical section of the lower part of the shaft, shows the details of the deepening programme.During the planning period, Giant had a rather small supervisory staff and at the same time was experiencing a heavy labour turnover. As it was obvious that production would suffer if the sinking crew were recruited at the mine, it was decided that the merits of contracting-the shaft sinking to an independent contractor should be investigated."

Jan 1, 1955

By Edward L. McHugh

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 5-acre Zwagg Island Wilderness Study Area (OR-12-14) in order to evaluate its identified mineral resources. The study area is located in Curry County, OR, immediately west of Brookings. There is no evidence of mining activity on or near Zwagg Island, and no mineral resources were identified. The steep-sided, flat-topped island is normally accessible from the mainland by way of a sandy beach. The island consists mainly of marine sandstone, mudstone, and conglomerate of the Jurassic Dothan Formation. Dothan Formation sandstone has been used locally as construction material. Rock along the coast has also been used for construction of jetties to improve harbor access; additional work has been proposed at the port of Brookings. Although suitable for other construction uses, stone from Zwagg Island would probably not meet physical requirements for jetty stone. Development of a stone resource on the island is unlikely.

Jan 1, 1987

By Herbert Pöllmann

Waste disposals are needed for safe deposition of different kinds of materials which can not be used as secondary raw materials. Often high contents of heavy metals must be bonded tightly to cristalline compounds to protect the environment from contamination. Therefore it is important. to find minerals which are capable to incorporate different heavy metals and protect the ground water. The power of resistance against leaching out effects of highly water-soluble salts can be increased. Mineral groups of metal hydroxy salts, ettringites, apatites, sodalites and calciumchlorosilicates and their hydrates are recommended for their formation in mineral reservoirs. Different wastes as red mud, gasification ash, garbage combustion ash and fluidized bed ashes were included in this study. The formation of different new compounds and their properties were determined.

Jan 1, 1991

By Alexander May

The Bureau of Mines, in cooperation with the Florida phosphate mining industry, investigated the dewatering of waste phosphatic slimes. Part of this investigation was to determine the electrophoretic mobilities and cation exchange capacities of the slimes. The mobilities and exchange capacities are reported for samples of slimes taken from 15 plants operating in the Florida land-pebble phosphate district that includes Polk,Hillsborough, Manatee, Hardee, and DeSoto Counties. The electrophoretic mobilities determined were all negative, ranging from -0.24 to -1.93 (micrometers per second) per (volt per centimeter). Also reported are frequency distributions of electrophoretic mobilities, electrophoretic mobilities of slime diluted with distilled water and electrophoretic mobilities of sand-slime mixtures. The cation exchange capacities ranged from 17 to 45 milliequivalents per 100 grams of slime solids.

Jan 1, 1975

By Virginia T. McLemore

The Gallinas Mountains are in northern Lincoln County and southern Torrance County, New Mexico, USA where a series of alkaline igneous bodies, including porphyritic latite, trachyte/syenite, andesite, and rhyolite laccoliths, flows, dikes, and plugs, have intruded Permian sedimentary rocks belonging to the Permian Abo, Yeso, and Glorieta Formations. A small amount of bastnaesite, a REE mineral, was recovered during processing for fluorite from the Gallinas Mountains. Four types of deposits are found in the Gallinas Mountains: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipes and iron skarn deposits; all are associated with Tertiary alkaline to alkalic-calcic igneous rocks. Alteration includes brecciation, silicification, chloritization, and fenitization. District zonation is defined by Cu-REE-F (±Pb, Zn, Ag) veins that form center of the district, surrounded by REE-F veins. Carbonatites are inferred at depth by the presence of fenitization, carbonatization of the breccias, presence of REE and similarity of the intrusive rocks and mineralization to areas with known carbonatites.

May 1, 2011

By Mauro Araújo Medeiros

Os aços inoxidáveis dupex tem sido largamente empregado em vários setores da industria principalmente em virtude da sua boa combinação entre suas propriedades mecânicas e resistência a corrosão. Um aço inoxidável duplex DIN W. Nr. 14462 foi submetido a ensaios de torção a quente com taxas de deformação de 0,3; 0,5; 1; 3 e 5 s-1 a temperaturas que variou entre 1.000 e 1.150°C. As amostras deformadas foram analisas através de microscopia ótica. As configurações das curvas de escoamento plástico foram analisadas em termos dos parâmetros de fluxo localizado como um mecanismo de acomodação da deformação durante a torção a quente. As microestruturas reveladas mostraram que o comportamento plástico do material é influenciado pela disposição inicial das partículas de austenita na matriz ferrítica e a queda de tensão após o pico esta relacionada à ocorrência de fluxo localizado na matriz ferrítica associado à fragmentação das partículas de austenita durante o processamento, bem como aos fenômenos de recuperação e recristalização dinâmica, típicos dos aços inoxidáveis duplex.

Aug 8, 2018

By Q. Zhang, J. A. Finch

"Sphalerite flotation in the absence of copper activation at moderately alkaline pH has been observed in laboratory studies. An in-plant test of this observation was conducted at Kidd Creek Mine LTD. using a portable minicell flotation circuit. The results confirm that raising the pH causes sphalerite flotation.The testwork with the minicell circuit is described. The circuit, built around 2, 51 cells donated by the Noranda Technology Centre, was funded by Air Liquide and NSERC. It includes a data acquisition system to monitor continuously dissolved oxygen, pH and Pulp potential.INTRODUCTIONFlotation of sphalerite is normally practised by adding CuSO4 as an activator under alkaline pH. Recently there have been a number of laboratory and plant examples of sphalerite flotation without deliberate addition of cu++ ions (Girczys, 1972; Mukherjee, 1976; McTavish, 1980; Marouf et al., 1986; Mielczarski, 1986; Leroux et al., 1987; Palsson and Forssberg, 1989; Sandoval-Caballero et al., 1990; Zhang et al., 1991).In batch tests, with a sample of Pb/Zn ore from Polaris, Leroux et al. (1987) found that sphalerite became floatable after adjusting pH to 9. 5-11: they ruled out natural floatability or the formation of elemental sulphur on the surface but suspected iron hydroxy compounds were responsible. Sandoval-Caballero (1990) conducted a continuous minicell test at Brunswick Mining and obtained a 44 % Zn recovery and 40.5 % Zn grade concentrate without deliberately adding CuS04 at pH= 10.5. With single mineral studies, Zhang et al. (1991) revealed good sphalerite floatability (over 80% recovery) in pH range 8 to 11 and found that this floatability was related to pH, dissolved oxygen (DO) level and Fe++ species present in the system.To explore further the conditions under which sphalerite can float without addition of CuSO4 , a continuous pilot test using minicells was performed at Falconbridge Ltd., Kidd Creek division. The set-up is briefly described (a more detailed description is given elsewhere in these proceedings) with emphasis on the data acquisition system - dissolved oxygen, pulp potential and pH were monitored continuously. Results of testwork investigating pH, CuS04 addition and gas composition are presented."

Jan 1, 1992