Search Documents

By E. Öğretici, S. Kahraman

The indirect estimation of intact rock properties is particularly useful for preliminary investigations in engineering projects. In this paper we examine the usability of electrical resistivity, a nondestructive measurement, for the prediction of physical and mechanical rock characteristics. Physico-mechanical tests (uniaxial compression, Brazilian tensile, density, and porosity tests) and electrical resistivity measurements were performed on specimens of 36 rock types. Before the resistivity tests, the specimens were completely saturated with saline solution. Evaluation of the test results showed that there are medium or strong correlations between resistivity and rock properties. There are also strong or stronger correlations between the two parameters for the rock classes. The regression equations developed were statistically tested, and their validity was confirmed. The results were also compared with previous studies. The conclusion is that electrical resistivity measurement can be used for reliably estimating physical and mechanical rock characteristics.

Aug 8, 2024

By J. Stephen Slottee, Jerold Johnson

The use of a thickener, without filtration, to produce a non-settling paste (also called thickened tailings) with non-Newtonian rheology has been practiced in Australia for many years for the disposal of red mud. The application of paste thickening technology outside of alumina is relatively new. Interest and installations in paste thickening are rapidly growing. Water shortages and environmental pressures make consideration of thickening tailings to solids concentrations within the paste range necessary in most new tailings projects. The paste thickeners at the DeBeers CTP plant in Kimberley, South Africa are the latest example of paste tailings disposal on the surface, also called “stacking”. Houman (2003) The use of a paste thickener as an alternative to filtration for mine paste backfill is a more recently developed application. This paper describes the principles of design and general operating characteristics of a paste thickener compared to the conventional and high-rate thickener. The application and operating performance of paste thickeners in mine backfill is discussed as an example. An integrated approach to process design is described that matches the performance of the thickener, pumping system, and application on a common rheological basis to ensure that none of these steps prevents achieving process performance targets.

Jan 1, 2005

By L. E. Djingheuzian

"IntroductionIN 1940, in a series of articles, M. W. von Bernewitz(l) reviewed in detail roasting of gold and silver sulphide ores and concentrates. Since that time some significant developments in roasting have taken place, and a number of papers have appeared in the Canadian technical literature, dealing severally with the roasting of a particular ore or concentrate.The purpose of this paper is not only to review some of these Canadian papers and bring the information on Canadian roasting practices to .date, but also to analyse the mechanism of roasting. Hence, it is proposed to start with a study of physico-cl1emical factors fundamental in roasting, the knowledge of which, by creating a sound basis for a proper roaster design, makes good roasting possible.Physico-Chemical FactorsRoasting can be defined as heating sulphide ores in presence of air below fusion points of the constituent minerals, at such temperatures as to convert metallic sulphides to oxides. Hence, roasting is a chemical process.The object of roasting is, by changing, chemically, mineral constituents of sulphide ores, to make the economic recovery of the desired •Constituent metal by a subsequent standard treatment possible. For instance, pyritic ores, containing gold in sub-microscopic form which no amount of grinding would release, are roasted in order, by oxidizing the sulphides, to open up their structures to such an extent as to enable cyanide solutions to come into contact with the gold and dissolve it. The production of porous calcine is, therefore, the object of roasting of refractory auriferous sulphide ores or concentrates. Such a porous calcine may be defined as a desirable calcine, and the roasts which produce desirable calcines can in their turn be termed desirable roasts."

Jan 1, 1952

By Katherine A. Margolis

Refuge Chamber Expectations Training was created by a multidisciplinary team at the National Institute for Occupational Safety and Health (NIOSH) to inform miners of what to expect psychologically and physically if it became necessary to use a refuge chamber in a mine emergency. The presentation can be used either for one large group or for individual miners. The training is a multimedia Adobe Flash presentation containing pictures, audio, video, and interviews with miners who have used a refuge chamber in an emergency. It must be run on a computer with Adobe Flash Player installed (refer to the computer system requirements section).

Oct 1, 2009

By M. D. Max, A. H. Johnson

INTRODUCTION Gas hydrates have considerable potential to be a major energy resource owing to their apparent abundance in Arctic regions and along continental margins throughout the world (Kvenvolden, 1988). Yet, the oil and gas industry has been slow to pursue this opportunity. The primary reasons for this are the large conventional reserve base for natural gas worldwide and the perception that gas hydrate will not be a viable resource for another twenty or thirty years. Gas hydrates are thus viewed as a potential resource for the distant future, but not a valid investment for the near term. This paper addresses both global gas markets and gas hydrate technology, and shows that the commercial development of gas hydrate could proceed rapidly enough to constitute a near-term energy resource. GLOBAL GAS MARKETS The proven worldwide reserves of conventional natural gas are truly enormous, totaling over 6,000 TCF according to BP (2004). Moreover, those reserves have nearly doubled during the past two decades and now represent 67 years of consumption at the current production rates of 80 TCF per year (Fig. 1). This reserve increase has occurred even as global production of natural gas has increased by 67% during the same two decades (Fig. 2). While declining conventional gas reserves are a concern in North America, especially in regions where established infrastructure exists to bring gas to consumers, large new discoveries continue to be made elsewhere in the world. Indeed, in many parts of the world (such as the Middle East and parts of West Africa), natural gas has been regarded as an essentially worthless byproduct of oil production or exists in stranded gas fields. Given this situation, pursuing unconventional gas resources that are inherently riskier exploration targets and more expensive to produce would appear to have little rationale from a business standpoint.

Jan 1, 2006

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

By BO HYUN KIM, MARK K. LARSON

The floor-heave and no-floor-heave phenomena at a western U.S. coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria. Although the previous numerical study using FLAC3D very reasonably demonstrated these phenomena, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. As a result, the latter models predicted floor heave that agreed with relative amounts of observed heave from each gateroad system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Sep 1, 2022

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By J. Douglas Causey

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied the 7,940-acre Southern Otay Mountain Wilderness Study Area (CA-060-029), and the 5,750-acre Western Otay Mountain Wilderness Study Area (CA-060-028) in order to evaluate their mineral resources. The wilderness study areas are located in San Diego County, CA, about 20 miles southeast of San Diego. No mineral resources were identified in the Southern or Western Otay Mountain Wilderness Study Areas, based on literature, field observations, and sample results. The wilderness study areas are underlain by a complex blend of Late Jurassic, moderately metamorphosed sedimentary and volcanic rocks. Evidence of mineralization is not obvious.

Jan 1, 1987

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By Edward F. Redente

Several research projects have been conducted in the western United States to determine the optimum soil replacement thickness for reconstruction of rangeland and cropland. However, the information gained from these studies tends to be site-specific and not broadly applicable. Moreover, the possible interaction between soil thickness and mechanical and fertilizer manipulation of the overburden has not been adequately studied. To meet these information needs, research was initiated at Trapper Mine in northwestern Colorado in 1980 to study vegetation response to soil thicknesses of 15,30,45, and 60 cm and five manipulations that included disking, ripping, and fertilizing. All crops were harvested at peak standing crop and then weighed in the laboratory. Wheat grain yields were highest when soil thickness was 45 cm and the soil and overburden were ripped. Alfalfa yields appeared to be highest when overburden was disked and fertilized and soil was replaced to a thickness of 60 cm. For range vegetation, standing crop biomass was highest when overburden was ripped and soil was replaced to 60 cm thick. However, optimum performance was obtained from the maximum number of species and life forms by disking overburden and replacing 15 cm of soil. The performance of most range plant species has improved over the three years of the study. When the results of this study are compared to the results of other soil thickness studies, we can conclude that selection of management practices should be influenced by local climate, local soil and overburden conditions, type of crop or vegetation to be grown, and specific management goals for that crop or vegetation.

Jan 1, 1984

By A. R. T. Dennues

"INTRODUCTION There are presented in this report the results of limited studies by the Bureau of Mines of the firedamp safety of some powder-powered tools proposed for use underground in coal mines. This study was made to obtain general information and specific technical data for a cable splicer and some rail punches now commercially available, the aim being to keep abreast of developments and to anticipate hazards.ACKNOWLEDGMENTSAcknowledgments are made to the Mine Safety Appliances Co., Pittsburgh, Pa., for supplying equipment for these tests, and to the Pittsburgh Coal Co. for making possible observations of the use of these tools in coal mines.The assistance of other members of the Explosives Division is acknowledged: J. E. Crawshaw, for examination of ammunition and, propellant powders; H. L. Wilson, for analyses of the natural gas used in the gallery and Jerome C. P. Weinheimer and Martin Bashel, for conducting the gallery tests.GENERALDescriptions of the DevicesPowder-powered tools of the type tested utilize the energy of charge of,propellant powder accomplish tasks. They are essentially small guns adapted to special work. Of the family of such tools now commercially available from one manufacturer, two have been proposed for use underground in coal mines, namely a cable splicer known as model TI and two models of rail punch known as R40 and R60. These tools employ blank-cartridge ammunition and special projectiles to accomplish the work indicated by these descriptive names."

Jul 1, 1947

By James Westfield

Following is a brief resume of the Division's activities that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1961

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By E. G. King

Heat of formation values for mercuric sulfide appear in all the comprehensive listings of thermodynamic data, but experimentally determined entropy values have been lacking. Consequently, all free energy calculations involving mercuric sulfide have been based upon estimated entropy values. This paper reports Bureau of Mines measurements of the low-temperature heat capacity of red mercuric sulfide (cinnabar) and the entropy value at 298.15° K. derived therefrom. The entropy value was combined with heat data to obtain free energy values for the formation of red mercuric sulfide from liquid or gaseous mercury and from rhombic or gaseous diatomic sulfur.

Jan 1, 1962

By Guilherme Corrêa Soares

The effects of temperature and strain rate on the mechanical behavior of a superelastic NiTi wire were investigated by uniaxial tensile testing. A universal testing machine with an attached heating chamber was used for the tensile tests. Temperature influence was studied through straining of samples until rupture at a fixed strain rate and temperatures of 25, 50, 75, 100, 125, 150, 175 and 200 °C. Strain rate effects were investigated by straining samples until rupture at room temperature and strain rates of 10-2, 5 x10-3 , 10-3, 5 x 10-4 and 10-4 s-1. The effects of temperature and strain rate on NiTi mechanical behavior were discussed in terms of critical stress to induce martensite and austenite yield strength, when applicable; upper plateau stress, transformation plateau length and ultimate plateau stress. It was found that increasing test temperature and strain rate shifted the stress-strain curve upwards, albeit temperature displayed a greater influence. Plateau length increased with temperature, but no significant changes were detected as a result of different strain rates.

Aug 17, 2017

By P G. Gaylard

The minerals Industry carries out over US$ 2 billion of R&D annually. The R&D is performed at three levels ? in house research facilities; on a one-on-one basis with a research provider; as syndicated (collaborative) research. The key to a successful R&D programme is project selection. It is suggested that at this time of ?bounty? for the minerals industry the research portfolio should contain some ?blue sky? but potentially long term significantly beneficial projects. This said, the projects should align the technical concepts with the business imperatives. AMIRA has found the ?Road Map? concept has assisted in defining areas for R&D. Examples of this methodology using a Copper Road Map developed by AMIRA for the copper producers operating in South America is presented. The benefits derived from syndicated research are also discussed.

Jan 1, 2007

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994