Search Documents

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) The system design of hydrostatic drives for mine hoists, usually of special nature, is considered along with oil hydraulic component selection suitable for the application; (b) The criteria for head frames of steel and/or concrete are developed with full consideration of all operating and environmental conditions.

Jan 1, 1988

By Leandro de Almeida

As curvas limite de conformação (CLC) são utilizadas há mais de 50 anos. Propostas inicialmente para o desenvolvimento de produtos provenientes da indústria automobilística, em função das necessidades apresentadas pela indústria de estampagem elas são aplicadas atualmente de maneira geral na produção de inúmeros tipos de peças, oferecendo previsões de possíveis falhas e/ou defeitos durante as etapas do processo de estampagem. As CLC´s permitem prever o afinamento excessivo, enrugamento, estiramento e é claro, a fratura da peça. A raiz da curva limite de conformação (CLC0) é considerada como a mínima deformação obtida pela curva, ou seja, a obtenção de deformações superiores pode levar a peça a falha. As ligas de latão compostas por cobre e zinco, são utilizadas em inúmeras aplicações que necessitam de excelente estampabilidade, como o repuxo profundo, objetivado na fabricação de projéteis. Desta forma, torna-se interessante o entendimento da CLC ou CLC0 para liga de latão em estudo. A obtenção da CLC0 através de ensaios de tração uniaxial no plano da chapa pode ser realizada de acordo com corpos de prova de formatos específicos, como os propostos por Björklund e Nilsson (2014), IRSID (1975) e Wagoner (1980 e 1981). Concluiu-se que o corpo de prova proposto pelo IRSID (1975) é o que melhor se apresentou na determinação das deformações e1 x e2 e com rompimentos dos corpos de prova na região central.

Oct 30, 2017

By Sylvie Brassard

Available information ?? InfoMine: mineral properties ?? Metals Economics Group: budgeted exploration expenses ?? MineScan: Canadian and American Mining Companies ?? Statistics Canada: Canadian Direct Investment Abroad, by Sector in the world OR all sectors by Country

May 1, 2008

By Rodrigo Alves Caetano

A Usiminas, maior siderúrgica latino-americana fornecedora de aços planos, tem dedicado grandes esforços para oferecer materiais mais adequados para as diferentes demandas do mercado, desenvolvendo novos tipos de aços para utilização em carrocerias veiculares. O objetivo deste estudo foi caracterizar o comportamento de dois produtos Usiminas, o aço DP780 galvanizado por imersão a quente e o aço TRIP780 eletrogalvanizado, ambos com espessura de 1,50 mm, revestimento zinco puro e camada de 50 g/m² por face, com base em análises metalográficas, ensaios de tração, ensaios de estampagem e ensaios Bake Hardening (BH) e Aging Index (AI). Os resultados destas avaliações mostraram que os aços TRIP780 e DP780 tiveram performances excelentes em todos os modos de estampagem avaliados, além de boa capacidade de endurecimento após pintura (efeito BH). Tratam-se, portanto, de boas opções para aplicação em peças da carroceria, principalmente em componentes que requeiram elevada resistência mecânica.

Aug 16, 2017

By Alexandre de Souza Rios

Neste estudo, caracterizações morfológicas e mecânicas foram utilizadas em fibras de coco brasileiras na condição como recebida e tratadas superficialmente (por NaOH, aquecidas e por NaOH seguido de aquecimento) e em mantas de fibras de coco fabricadas por compressão. Para a análise morfológica foi utilizada a Microscopia Eletrônica de Varredura (MEV) e para a análise mecânica foi utilizado o ensaio de tração uniaxial. As análises por MEV apresentaram que as fibras tratadas por NaOH possuem paredes celulares externas mais nítidas e partículas circulares com diâmetros de aproximadamente 10 µm. O tratamento químico alterou a parede externa das fibras de coco; em uma das amostras foram vistas microtrincas da ordem de 7 a 60 µm em virtude do tratamento seguido de aquecimento. O módulo inicial (módulo de elasticidade) e a tensão de ruptura diminuíram com o aumento de diâmetro nas quatro condições de fibras de coco estudadas. A geometria e a massa da manta de fibra de coco influenciaram no seu comportamento mecânico.

Aug 16, 2017

By Roberto Seno Júnior

O Processo Bayer para a produção de Óxido de Alumínio consiste em dissolver o alumínio presente na minério de alumínio (Bauxita) com soda cáustica à quente. Os resíduos insolúveis são separados por decantação e filtração. Após lavagem deste resíduo para a recuperação da alumina e soda cáustica ele é transferido para áreas de disposição. A Companhia Brasileira de Alumínio produz 420 mil toneladas de alumínio por ano gerando cerca de 2.400 toneladas de resíduo de bauxita por dia. Este resíduo é transferido para uma área de disposição, denominada Palmital, com capacidade de estocagem para mais 9 anos. Atualmente, o Palmital contém cerca de 2 milhões de metros cúbicos de água sobrenadante. Esta água contém alumínio e soda cáustica dissolvidos que podem ser reutilizados na Refinaria de Alumina. Este trabalho estuda formas de reutilização desta água sobrenadante visando aumentar a vida útil do Palmital, ou seja, aumentar o volume disponível para disposição de resíduo de bauxita.

Jul 31, 2018

By Diego Berti Salvaro

A morfologia, dimensões e composição química de tribocamadas são fortemente dependentes das pressões e temperaturas existentes no contato e oriundas das reações das superfícies entre si, com a atmosfera, com os lubrificantes e contaminantes presentes no contato. No presente artigo foi analisada a formação de tribocamadas em pares DLCaço inoxidável testados por 180, 500, 1000 e 2500 horas em atmosfera de gás refrigerante R134a sem a presença de óleo lubrificante. A caracterização foi realizada por microscopia eletrônica de varredura espectroscopia de energia dispersiva (MEV-EDS) (morfologia e composição química) e interferometria ótica de luz branca (dimensões). Nas análises por MEV-EDS foram identificadas tribocamadas que se apresentaram mais pronunciadas nas superfícies do aço inoxidável sendo as mesmas oriundas de transferências mútuas entre os pares tribológicos bem como oxidação. A espessura das tribocamadas, por sua vez variou de 100 a 500 nm. Os resultados revelam que as tribocamadas são quimicamente estáveis e que suas espessuras não variam significativamente após mil horas de ensaio.

Aug 16, 2017

By Susana Marraccini Giampietri Lebrão, Jorge Alberto Soares Tenório, Renato Souza e Silva, Guilherme Wolf Lebrão, Viviane Tavares de Moraes

Os resíduos eletroeletrônicos podem ser compostos por equipamentos ou parte deles, que se tornaram obsoletos, pararam de funcionar ou ainda por apresentar defeitos durante a sua produção. As placas de circuito impresso (PCIs) são peças presentes em equipamentos eletroeletrônicos compostos por materiais metálicos, cerâmicos e poliméricos. Para alguns destes metais já existem processos para recuperação, contudo estes processos baseiam-se em técnicas pirometalúrgicas que podem liberar substâncias tóxicas. A fim de minimizar os impactos ambientais propõe-se o beneficiamento das PCIs através de rota hidrometalúrgica para a obtenção de cobre em solução e, posteriormente fazer a redução do cobre. Para tanto se fez a moagem das PCIs, seguida de caracterização química. Partiu-se para rota hidrometalúrgica em meio ácido e em meio oxidante. A solução resultante de cobre foi reduzida para cobre metálico por reação de redução com ácido ascórbico. Os resultados apresentam recuperação de 97 % de cobre das PCIs com obtenção de cobre metálico.

Oct 11, 2019

By C. J. Chindgren

Upgrading of commercial red cake and recovery of vanadium oxide from uranium-vanadium mill solutions were investigated by the Bureau of Mines. Alternative procedures potentially useful for manufacture of high-quality vanadium oxide at the mill site were explored and developed. The simplest and best procedure for converting commercial red cake containing about 10 percent combined sodium and potassium oxides (Na20) (K20) into a 98- to 99-percent vanadium pentoxide (V205 product appeared to be a metathesis in an ammoniacal solution of ammonium sulfate. Molybdenum, as well as the alkali metal oxides, was removed from the red cake by this procedure at a modest expenditure of labor and reagents. When preparing vanadium oxide of higher grade, it was necessary to dissolve the red cake and reprecipitate the vanadium as ammonium metavanadate. Calcination at 450° C, decomposed the metavanadate and yielded oxide of about 99.5 percent V205. By recyrstallizing the metavanadate before decomposition, an oxide product approaching 99.9-percent purity was obtained.

Jan 1, 1962

By G. R. McMeekin

"THE TOPIC suggested for my contribution to this Symposium was ""Lead-Zinc Smelting - 40 Years of Pollution Control"". The history of the development of smelting industry at Trail and the control of sulphur dioxide could make quite an interesting historical study. However, in the field of environmental control, the public is not particularly interested in what you did yesterday, but rather what you are doing today and what you are planning to do tomorrow. I can't fault this approach, but because there are some subject lessons that history can demonstrate, I would like to tell enough of the story (under three headings) to bring a focus on matters of contemporary concern in regard to public relations and ecology. The three general headings suggested are: (1) time before the capture of by-product sulphur; (2) the capture of sulphur; and (3) the ecological and public relations conclusions from these."

Jan 1, 1972

By Marcos Paulo Kohler Caldas

Após a sanção da RoHS Directive 2002/95/EC que entrou em vigor em 01/07/2006 proibindo a utilização de seis substâncias perigosas, sendo elas: chumbo, mercúrio, cádmio, cromo hexavalente, bifenilos polibromados e éteres difenil-polibromado fabricantes de equipamentos eletroeletrônicos tiveram que restringir os usos de tais substâncias. Com isto, as placas de circuito impresso dos equipamentos passaram a ser identificadas com a sigla RoHS ou outra identificação que indique o atendimento a diretiva. O presente trabalho visa analisar um lote de placas mãe de computadores obsoletos direcionados ao CEDIR-USP (Centro de Descarte e Reuso de Resíduos de Informática) no período de 01/01/2013 a 30/05/2013, identificando-as como “lead free” ou “comuns”, a fim de verificar a relação entre placas livres de substâncias perigosas e placas contendo tais substâncias. O lote possuía quantidade aproximada de 3.230 placas. Após a separação, as placas “lead free” foram classificadas por marca e nacionalidade. O resultado da pesquisa mostrou que mesmo após onze anos da edição da diretiva o percentual de placas livres de substâncias perigosas ainda é muito baixo. Cerca de 97,80% das placas de circuito impresso coletadas ainda possuem em sua composição substâncias perigosas. Verificou-se que todas as placas “lead free” encontradas são de origem chinesa e seus fabricantes são: Gigabayte, Itautec, Intel e CE. O estudo também classifica a origem dos resíduos como: industriais, da própria universidade ou residenciais.

Aug 8, 2018

By Stephen D. Hill

The Bureau of Mines devised and constructed a modified Knudsen effusion apparatus, permitting a constant measure of the weight of effusing vapor, to determine the equilibrium vapor pressure of metal halides at temperatures up to 1,200° K and over the pressure range 10-5 to 10-2 torr. The reliability of the apparatus was established by determining the vapor pressure of potassium chloride. After correcting for partial dimerization of the vapor, data obtained on solid KCl between 750° and 950° K can be expressed by the following equation:

Jan 1, 1966

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By Kenneth M. Maas

The Bureau of Mines inventoried the land in southwestern Alaska to classify ownership and availability and compared this land with known mineral terranes and mineral deposits. This report discusses and quantifies the potential for favorable location of mining claims for metalliferous (locatable) mineral deposits. Of the nearly 24 million acres that constitute the study area, approximately 3.6 million acres or 17% are available for mineral location, 3.4 million acres or 14% are available with restrictions, and 17 million acres or 71% are unavailable. Mineral terranes are known to underlie about 7.8 million acres or 33% of the study area; 3 million acres or 38% occur on land available for mineral location, 1.3 million acres or 17% occur on land available with restrictions, and 3.5 million acres or 45% occur on unavailable land. The State of Alaska has opened over 91 % of its land in the study area to mineral location; in comparison, the Federal Government allows mineral location on 0.07% of the land under its jurisdiction. There are 117 known mineral deposits or occurrences within the study area, including 77 lode deposits and 40 placer deposits. Of the 41 lode deposits occurring within a mineral terrane, 2 occur on available land.

Jan 1, 1988

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

Electricity supply constraints in SA are increasingly challenging mines to operate more energy efficiently without reducing production output. Mining compressed air systems are well known to be operated inefficiently and are also a major power consumer. Two available and proven technologies can be applied on new and existing mines to replace or and optimise available compressed air facilities and achieve meaningful reductions in electrical power consumption; ? Hydro powered drilling and mining is significantly more energy efficient than compressed air and provides drilling rates that are twice as fast. ? Stope drilling systems using compressed-air or water drills allow further energy savings. The technologies are discussed and a broad strategy to selectively apply these them together is presented.

Jan 1, 2008

By H. Shafick Hanna

The major problems are identified the high phosphorus content and the fine dissemination or encapsulation of mineral impurities, in, ,the iron bearing minerals, A process which combined extreme fine grinding techniques with magnetizing roasting or flotation separation methods, is suggested. By these methods concentrates assaying 60-61 percent Fe exceeding the widely accepted upper limit of 56 percent Fe set for these ores, were produced with 75-90 percent iron recovery. Moreover it was shown that the phosphorus content of these concentrates could be reduced from 0.25 to 0.03 percent phosphorus by acid leaching. A brief discussion on production costs based on current and future developments in iron ore processing is given.

Jan 1, 1980

By J. Douglas Causey

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 12,740-acre Blue Canyon Wilderness Study Area (OR-003-073) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 27 miles northwest of Jordan Valley. The study area is underlain by Tertiary welded tuff, tuff, perlite and tuffaceous sedimentary rocks capped by basalt. Jasper has been mined from several localities. Some mining has been done by hobbyists. However, the area has been covered by mining claims since 1964, with mining done by commercial operators. This region has been a source of "Owyhee picture" and other similar jaspers. More recent exploration has focused on the gold potential of nearby areas such as Quartz Mountain and Red Butte.

Jan 1, 1989

By D. Bois, P. Poirier, B. Bussière

Environmental desulphurization is an attractive alternative for the management of acid generating tailings. Bulk sulphide flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works. This process can reduce the volume of problematic tailings to manage by making a sulphide fraction concentrate. The desulphurized tailings can then be used as construction material for an engineered cover to prevent acid mine drainage. In this paper, the results from different laboratory and pilot scale flotation tests are presented. These results confirm that low sulphide non-acid generating tailings can be produced by froth flotation. It is also demonstrated that sulphide concentrates obtained from desulphurization mixed with the appropriate binders can be used as feed material for paste backfill. From previous work on the evaluation of operating and capital costs of the desulphurization process for different ore types, the use of desulphurization as a tailings management approach was studied for several scenarios. The desulphurization process was then compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation. Results show that partial or total desulphurization are technically and economically viable options to manage tailings during mine operation. Mine waste managers should consider desulphurization as an efficient technology.

Jan 1, 2005