Search Documents

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

By L. J. Kashar

By means of a continuum-mechanics approach, the following equation for calculuting the pressure for axisymmetric cold forging has been derived: where P is the extrusion pressure; K and n are the strength coefficient and the strain-hardening exponent of the steel, respectively; a and b are strain factors, primarily dependent on the die design; and R is the extrusion ratio. Data from compression and backward-extrusion tests performed at a crosshead speed of 0.5 in. per min on a nonwork-hardening material pure lead) and on a work-hardening material (1018 steel) indicate that the predicted extrusion pressures obtained from the derived equation agree very closely with the actual extrusion pressures. Therefore, the equation can be used to predict backward-extrusion pressures from standard mechanical-test data. The decision to cold-forge a part is based on several considerations, most of them related to economics. However, the production feasibility is usually determined by the pressure needed to extrude the part and the availability of tooling that can repeatedly sustain this pressure for over several hundred thousand cycles. A major contribution to the cold forging of steel would result from the development of steels that could be forged at reduced pressures and from the development of techniques that permit the accurate prediction of the pressure necessary to cold-forge the part. The ability to predict extrusion pressures is necessary to properly design the tooling required for the cold-forging process. Attempts to theoretically predict the cold-forging pressure, especially for work-hardening materials, have been unsuccessful in previous investigations of the cold-forging process.1-3 Many empirical relations have, therefore, been proposed relating the extrusion pressure to the chemical composition,' the extrusion ratio,2 the tensile strength,273 and hard- ness, 2 and the yield strength3 of the material being extruded. However, these empirical relations are valid only for the specific conditions used in their development, and, in some cases, the empirical relations had a scatter band greater than * 10 pct. A study of the extrusion process was undertaken with the objective of developing predictor equations for extrusion pressure by using a continuum-mechanics approach to the problem of metal flow. The derivation of such an equation is summarized in this paper, and data are presented that confirm the validity of the derived equation. DERIVATION OF THE EXTRUSION EQUATION If the extrusion of a material through a die is considered in terms of a work balance, it has been shown that it is possible to derive an equation relating the work necessary to move the material through the die to the deformation work undergone by the material. The work done, W, in moving the material is given by where F is the extrusion force, I, is the distance the material was moved, A, is the original cross-sectional area of the material, P is the extrusion pressure acting on A,, Ap is the cross-sectional area of the extrusion punch, and Pp is the punch pressure acting on Ap. The deformation work, WD, is given by where V is the volume of metal deformed, ay is the flow stress of the metal, and E is the total strain undergone in the extrusion. If there are no frictional losses, the work done, W, is equal to the deformation work, WD; therefore, Since the volume of a metal does not change during deformation,

Jan 1, 1968

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By T. Struminski

The paper is aimed to assess the possibilities of usage of pyrometers and thermal cameras to study ventilation and environmental conditions in underground mines. Surface and underground thermovision tests were carried out in the Rudna mine and included channels and diffusers of some selected fan stations, shaft crest closures, engines of central fans and their instrumentation. The thermovision underground tests in the Rudna mine consisted of ventilation barriers, underground fans, temperature of rocks, ventilation machines, parts of belt-conveyors and electric machinery.

Jan 1, 2003

Jan 1, 1999

By Staff

This U.S. Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles.

Jan 1, 1989

By F. R. Archibald

SINCE the opening of the Beattie mine, in 1933, the concentrate produced by flotation has been considered refractory. As the gold extraction by cyanidation was poor, the concentrate, during the first four and a half years of operation, was shipped to a smelter for further treatment. After the installation of the cyanide plant, in 1934, seventy per cent of the gold in the concentrate was recovered before shipment to the smelter. In 1937, a roasting plant was built so that treatment might be complete at the mine. Much experimental work had been done by a number of investigators prior to the installation of the roasters, but none of them had seriously attempted to identify the causes of, or the elements responsible for, the refractory behaviour of the concentrate. Intensive investigation in this direction commenced in the Beattie lab-oratory in July, 1938, has led not only to the identification of several causes contributory to the refractory behaviour, but also to revisions in procedure and principles with respect to roasting Beattie concentrate in particular and arsenical concentrates in general. The accuracy of the identification of these causes and the soundness of the principles is borne out by interpretation of roasting plant records, by improvements and simplification since applied. to plant operation, and also by laboratory and test-plant results on arsenical concentrate produced by another mine. It is the purpose here to present an account and interpretation of the laboratory investigation, together with a correlation of laboratory and plant results. Incomplete extraction of the gold by cyanidation after roasting is due primarily to the nature of the material roasted, and secondarily to the manner in which it has been roasted. There is a possibility that better extraction may be obtained by improvements in both particulars.

Jan 1, 1939

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

By R. S. Bowman, G. S. Austin, J. M. Barker, P. S. Freeman

The physical, chemical and mineralogic characteristics of zeolites allow commercially important applications. While adoption of zeolite technology is slow in the United States compared to other regions of the world, continued testing and research has shown a wide range of uses for these minerals. They are important catalysts in petroleum refining, molecular sieves able to separate gases, and chemically inert carriers of reactants. The zeolite clinoptilolite produced by St. Cloud Mining Company (clino) (SC) is used in animal hygiene and animal feed, especially concentrated animal feeding operations (CAFOs), horticulture, water treatment, floor dry, aquariums, air and other filters, and odour control. Clino can remove cations from solution, and surface-modified zeolite (SMZ) is a sorbent for the removal of anions and neutral organics from water. Specific clino applications are: control of chemical pollution in groundwater, removal of organic compounds from oil field waters, and elimination of pathogens from sewage effluent. Combining the sorption capabilities of SMZ with chemical or biological transformations can yield complete removal of toxic materials from contaminated water. Continued development and marketing of zeolite products will be a growth market far into the future. The CAFO market for zeolites is the most significant growth area in the United States over the next few years. SMZ, currently less than 1% of St. Cloud sales, will continue to gain market penetration for many years.

Jan 1, 2004

By P. J. K Leeuw, E. Uludag, M. J. Nong

Efficient drill-and-blast performance is pivotal to the profitability of deep-level mines, where high operating costs and declining grades demand maximum throughput. This study investigated persistent fragmentation problems at a longhole stoping operation that suffered from simultaneous oversized rock blockages in 300 mm × 300 mm grizzlies and excessive fines. Fifty-one muckpile images from five blasted stopes were analysed with Split-Desktop. Although the overall F₈₀ was 287 mm, nominally suitable for the grizzly aperture, the Rosin- Rammler uniformity index of 0.80 revealed a highly inconsistent size distribution containing both boulders and fines. Existing drill patterns were then evaluated with the Aegis underground software, which showed negligible crack overlap at the toe owing to inadequate spacing and burden. Insufficient energy overlap between blastholes, particularly at the toe, was found to contribute to the coarse fragmentation, while excessive fines were attributed to the crushing and severely fractured zones of blastholes. Optimisation simulations demonstrated that an 89 mm blasthole diameter on a 2 m × 2 m pattern would overlap, aligning with Aegis requirements of balancing powder factor, break angle, and energy distribution. Implementing this revised pattern is expected to reduce secondary breaking, prevent ore-pass blockages, lower fines, and ultimately improve overall production efficiency. The methodology illustrates how integrated image analysis and modelling software can effectively diagnose and address fragmentation issues, particularly in underground longhole mining, where challenging blasting conditions require a balance between achieving optimal fragmentation and maintaining stope stability. This approach offers a cost-effective pathway to improving comminution performance in deeplevel mines.

Oct 2, 2025

By A. Y. Lee

Prior work at the Bureau of Mines resulted in the successful development of a bench-scale, combination electrorefining-electrowinning method for recycling the lead from scrap batteries using waste fluosilicic acid (H2SiF6) as electrolyte. This paper describes larger scale experiments. Anodes cast from scrap battery lead were electrorefined in a 20-L multielectrode cell for 3 to 7 days. The anodes, containing 2 to 2.5 pct antimony, were ideal for obtaining firm and adherent slime blankets. Cathode deposits, assaying 99.99 pct Pb, were obtained, with current efficiencies near 99 pct. Sludge leaching was done in 100-L tanks followed by filtering in 61 cm square vacuum pan filtersu Lead of greater than 99.99-pct purity was recovered from the filtrate by electrowinning in a 20-L multielectrode cell using insoluble Pb02-Ti (lead dioxide-coated titanium) anodes and pure lead cathodes. The fluo-silicic acid electrolyte depleted in lead was repeatedly recycled to leach more sludge, and there was no problem with impurity buildup. The amount of Pb02 formed on the anodes during electrowinning was less than 1 pct of the total lead deposited on the cathodes, as long as the phosphorus concentration in the electrolyte was greater than 1.3 giL. Emissions of lead in air were less than 10 ~g/m3, well below the proposed OSHA limit of 50 ~g/m3.

Jan 1, 1984

By Abolfazl Eslami, Samieh Rezazadeh

"Semi-Deep skirted foundations are considered to be a viable option for a variety of onshore and offshore applications. It is necessary to determine appropriate foundation configurations that allow loads to be transferred safely to the surrounding soil. For this purpose the bearing capacity and stability analyses subjected to combined vertical, horizontal and moment loadings must be found. In this paper the vertical undrained bearing capacity is estimated via finite element analyses. The circular skirted foundations with different geometries considering embedment depth (embedment ratio between 0-2) and size effects (diameter equals to 5, 10, and 20) have been studied. Stress field, kinematic mechanism accompanying failure and bearing capacity factors for total, end and shaft resistance in semi-deep foundations with various embedment ratios are investigated. Furthermore, two probable mechanisms i.e. internal flow and soil plug for estimating foundation capacity for design purpose in practice have been assessed. Comparisons with different research works including conventional methods, upper and lower bound approaches, and finite element analyses have indicated that the conventional methods underestimate the bearing capacity due to ignoring the significant role of shaft resistance. Determining appropriate economic foundation configurations to transfer loads safely to the surrounding soil is a major issue in geotechnical engineering. Shape and dimension of foundations, embedment depth, soil characteristics and applied loading, all affect the foundation performance. Recent studies have shown that for foundations with large breadth and of D/B between 1 to 4, kinematic mechanisms and failure modes are different from the two main types of foundation (i.e. shallow and deep). Therefore, D/B factor must not be considered as the only factor for defining foundation type. ""Semi-Deep foundations"" are another foundation category distinguished based on their performance. This relatively new concept is becoming increasingly an optimum alternative for shallow and deep foundations to support structures especially in accessible depth. As illustrated in ""Fig. 1"", different types of semi-deep foundations consist of:"

Jan 1, 2017

By Charles L. Allie

Since Reserve Mining Co. began commercial operations at Silver Bay, MN, some 25 years ago, major improvements in taconite processing technology have become available. In addition, significant new government standards have been imposed on industrial operations. By implementing a $370-million modernization program, Reserve was able to accomplish two major company objectives: the quality of concentrates produced from the Peter Mitchell mine has improved, and the operation meets both present and foreseeable environmental standards. Process modifications at Reserve were designed to: •Reduce the pellet silica content from 9% to 5%; •Increase the pellet iron content from 62.5% to 65.8%; •Implement a tailings disposal system utilizing "best available technology" water quality controls; and •Reduce air emissions by installing "best available technology" air emission controls. By adding dry cobbing, fine screening, and flotation to the concentrating process, pellet silica content has been reduced; the process reclaims and reuses all process waters; all tailings are stored in a zero discharge tailings basin; and all air emission standards are being met. Initial Beneficiation at Silver Bay Reserve's Peter Mitchell mine at Babbitt, MN, is on the eastern end of the Biwabik iron formation. The open-pit mine is approximately 16 km long, 0.8 km wide, and presently has a maximum depth of about 50 m. Principal constituents of the ore body are magnetite, quartz, and iron-magnesium silicates. The company's large commercial plant began operating at Silver Bay, 75 rail km from the mine, in 1955. Facilities have historically had the capacity to process 31.5 Mt/a of taconite, containing an average 24% magnetic iron, into 11 Mt/a of iron ore pellets. Reserve's initial beneficiation process-which existed up to early 1979-consisted of two crushing stages at the Babbitt mine site, two additional crushing and screening stages at Silver Bay, grinding in a conventional rod-ball¬regrind mill circuit, size classification with cyclones, and concentration with magnetic and hydraulic separators. Concentrate produced by that circuit assayed 65% iron and 8.5% silica, with a screen analysis of 94% -44 µm, and a surface area of 9300 cm2/cm3. Pellets produced from this concentrate assayed 62.5% iron and 9% silica (dry basis). Construction began in 1977 to modify Reserve's operation. Process modifications were designed from pilot scale operations that had been operated and researched by Reserve for more than 10 years. There were two design restraints imposed on the process: economic constraints that Reserve continue to use much of the existing processes and structures in the new operation; and a substantial number of government-imposed permit constraints. In effect, the tailings process was designed first and then a concentrating process was developed that would "fit" the tailings disposal system. Operation of the modified process began in June 1980. Crushing Remains Unchanged No changes in process flow were made at either the Babbitt mine and crushing plant or at the Silver Bay fine crusher. Gyratory crushers reduce run-of-mine taconite to -90 mm-diam at the mine. Taconite is then transported to Silver Bay by intra-plant railroad. There are 10 fine crushing lines. Each consists of a double deck screen, followed by a heavy duty short head crusher, a second double deck screen, and second short head crusher. All screen undersize material bypasses the crushing lines, resulting in an open circuit crushing process. Fine crusher product is approximately 98% - 20 mm, 80% -12 mm, and 50% -10 mm in diameter. Each fine crusher line processes about 400 t/h of crude taconite. Cobbing Provides Aggregate for Tailings Dams The first major process change was the addition of dry cobbing, a dry magnetic separation step between the fine crusher and concentrator. Dry cobbing serves two major purposes in the new process. Its principal function is to provide large volumes of dry coarse aggregate for use in construction of tailings dams. This process rejects about 20% of the fine crusher product as tailings with a size analysis of 98% -20 mm and 50% - 10 mm. These tailings are free draining and have high frictional shear strengths-two key requirements for dam building aggregates. Fine crusher product is conveyed to a new dry cobbing building. Here crushed ore is discharged into one of two 30-minute capacity surge bins. Crushed ore is withdrawn by 12 constant speed conveyor belts; each discharges 500 t of crushed taconite into a dry cobbing machine. Each machine consists of a 3-m-long riffle splitter and two vari-

Jan 12, 1980

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By M. J. Laurila

The concentration of low grade iron ores to pellets or sinter fines suitable for blast furnace feed or direct reduction is highly energy intensive and costly in terns of both size reduction and separatory processes. Large equipment with high throughputs are required to make the fine grinds and multi-stage separations economical. Control of these circuits is essential to producing a high grade product. As a result, iron ore concentrators possess some of the more sophisticated instrumentation for process control in the mineral dressing industry. These instruments must characterize flowstreams of up to 8,000 gpm where 80% of the particles are less than 50 µm. The past decade has been one where enormous strides have been made in automated control of iron ore plants. This paper reviews state-of- the-art control systems for crushing, grinding, magnetic separation, froth flotation and sizing/classifying circuits. Trends toward computerization and plant automation in response to a dismal outlook for North American steel production are also examined.

Jan 1, 1984

By Adriaan de Villiers

Many conventional structural analysis and design methods in current use are not appropriate for the mining industry. Two major reasons for this are that: • The economic life of a particular mine is limited, and • Much of the equipment and machinery used by the mining industry operates at relatively low speeds. Both of these factors can have significant cost implications if they are not properly accounted for during plant design. In particular, the often used practice of mitigating excessive vibration by adding mass to machinery supports is not only expensive but may worsen the vibration effects. Some of these problems, such as increased wear and tear, are not always easy to trace back to inappropriate design. This article focuses on vibration related issues and demonstrates that the mining sector has unique problems requiring unique solutions. Vibration: the basics Historic developments leading to current vibration design practices provide the key to why such practices are often inappropriate for the mining industry. To understand this, it is necessary to introduce some basic vibration theory. Consider a simply supported beam or foundation on which a vibrating machine is mounted. For analysis of the system's dynamic response, it may be viewed as a mass attached to a spring and a damper, such as the shock absorber of a car.

Jan 1, 1992

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

By Christopher M. St. John, Tony F. Zahrah

Empirical and numerical methods are the two extremes of the tools available for the seismic design of subsurface excavations and underground structures. Both have their limitations: when relying on purely empirical methods directly relevant experience may be scant; site data may be insufficient to justify a comprehensive dynamic analysis. The primary purpose of this paper is to review the analytical tools available to the design engineer of subsurface excavations and underground structures. Particular attention is devoted to simplifed models that appear to be applicable in many practical cases.

Jan 1, 1985

By A. Aaltonen, S. Paloranta, H. Myllykangas

A property based dynamic model of flotation was built and validated for training purposes. The model is based on the work of the AMIRA P9 project. The recovery of each particle with composition and size is calculated in a given simulation step. The model takes into account machine and operational parameters such as air flowrate and froth height. The model was created using fullscale test data on Pyhlisalmi Cu-Zn-pyrite ore with flotation kinetics of multiphase particles determined. Simulation and validation shows that model can predict the dynamic behavior of the process accurately enough for training purposes.

Jan 1, 2009