Search Documents

By Rudolf E. Greuer

This study concerns itself with two topics of the mine ventilation - mine fire interface which, when the work for this study began, did not seem to receive sufficient attention. Section 1: Comments on Spontaneous Combustion of Coal in Mines It is attempted to describe heat generation, heat and oxygen transport, in such a way that existing experimental data for U.S. coals can be used to assess conditions inducive to spontaneous heatings quantitatively. Investigated are, in particular, critical air velocities, minimum sizes of coal accumulations, moisture contents and the influence of mining factors. An extensive, practice oriented literature survey is included. Section 2: The Early Detection of Mine Fires by Assessment. of Mine Gases The suitability of the major constituents of combustion products for an early detection of fires is discussed. The same is done for gas concentration ratios. Since it was felt (at least at the time when this report section was written) that the value of the carbon monoxide/oxygen deficiency ratio was overestimated, the usefulness of monitoring this ratio as compared to monitoring CO concentrations was critically investigated. The state of art concerning instrumentation and organization of fire detection systems is reviewed also.

Jan 1, 2011

By C. A. Pierce

STUDIES of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its com-mercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft. in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft, of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding for-mations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresses."1

Jan 1, 1938

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

By Jael Moutinho dos Santos

Em função do elevado consumo de corpos moedores de alto Cromo e do alto custo de sua fabricação com matéria prima nobre, busca-se o desenvolvimento de novas ligas de corpos moedores na busca de um melhor custo benefício. Devido ao efeito sinérgico do perfil de desgaste envolvendo fenômenos corrosivos e abrasivos em bolas de moinho, o desenvolvimento de novas ligas de ferro fundido branco alto cromo tem sido uma alternativa para suportar o desgaste precoce provocado por tais fenômenos. As amostras de corpos moedores, analisados mediante ensaio de análise química, dureza, análise micrográfica e seguidos de ensaios de moagem (úmido e seco), servirão a um desempenho comparativo para se designar a melhor liga a ser aplicada nos processos de moagem secundária de minério de ferro a úmido.

Oct 30, 2017

By Will B. Jamison

The most serious safety problems encountered in U. S. underground coal mines today are related to the roof bolting operation. Also, roof bolting is usually the operation which limits coal production of the section. The purpose of my paper is to review some of the research, developments, and new ideas related to roof bolting. Many of these ideas have originated at. coal mines or with manufacturers. Most of the research on fundamental improvements has been funded by, and is a part of, the excellent and broad plans of the Bureau of Mines.

Jan 1, 1977

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

The production of metallic titanium and titanium-rich alloys in forms useful to the engineer involves the use of certain techniques not usually necessary in fabricating the commoner metals and alloys. However, not all stages in the handling and shaping of titanium-base materials require the application of unfamiliar methods. It is the purpose of this paper to indicate where the well-known techniques are applicable as well as to outline the unusual operations which are necessitated by certain chemical characteristics of titanium.In brief, the characteristics just mentioned are manifestations of the very great reactivity of titanium, especially at elevated temperatures. Liquid titanium burns vigorously when brought into contact with air. It also reacts with practically all refractories, causing damage to the latter as well as undesirable contamination of the metal. Even solid titanium undergoes serious superficial contamination when heated above 800°C. in air for more than a few minutes. In addition to an oxide skin being formed, oxygen enters into solid solution in the surface of the metal causing the latter to become hardened and eventually embrittled.Up to date, titanium has been made only on a pilot plant scale by methods which produce a spongy or powdered product. Refractory problems have prevented the development of chemical reduction methods for making titanium in the form of a liquid pool from which ingots of useful size could be cast. Therefore the first part of this paper will cover the consolidation of powdered or spongy titanium. The latter portion will provide a brief description of...

Jan 1, 1950

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By Richard P. Sheldon

In the last several decades, techniques of data collection have been rapidly evolving. Automated spectroscopic techniques in the chemical analysis of rocks for example have advanced to the point that we can analyze samples faster than we can grind them. Remote sensors of LANDSAT give us intensity measurements in four color bands of every acre of the U.S. every 19 days. Common depth point seismic instrumentation systems used at sea for surveying and networks of seismometers arrayed around the country for earthquake studies likewise are generating vast amounts of data. These along with many other earth science data generating systems have caused a veritable data explosion. How do we deal with these enormous amounts of geologic data presently being produced as well as those produced in the past, and to be produced in the future? There is an immediate need to acquire and utilize past and present basic data in order to address today's national earth science problems. Also data being collected and stored now must be compatible with future data in order for us to be able to undertake the wide spectrum of analysis that must be made in the future. This is a big order! In order to organize and to be able to analyze these data, the USGS has embarked on a wide ranging program of compatible data base construction and the development of computer technology, based on interactive computing, to facilitate resource assessments and analyses. These activities are analogous to two sides of a coin. One side deals with the logic, philosophy, and mechanics of information storage and retrieval; and the other side deals with the sensible application of computer technology to the treatment of data. These

Jan 1, 1977

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By R. B. Mears, G. F. Sagar, R. H. Brown

There are well recognized procedures for determining the various tensile, fatigue, and other mechanical properties of the common structural materials. This makes it possible for engineers to design structures of various materials which have adequate initial strength to stand the stresses to which they are subjected in service. There is also considerable general information about protective measures suitable for protecting the usual structural materials from the effects of ordinary environments. However, often insufficient quantitative information is available on the combined effects of stress and corrosion to permit the designer satisfactorily to appraise the structure from the stress-corrosion standpoint. This situation is further complicated by the fact that the stresses causing stress¬corrosion failures are usually not the design stresses but rather the residual forming and assembly stresses which are generally of unknown magnitudes. Thus, tests which will rapidly evaluate the susceptibility of materials to stress-cor¬rosion failures are extremely useful. Of particular value are tests which can be applied to built-up structures as well as to simple specimens, since, as mentioned above, residual stresses often are caused by fabricating procedures and assembly operations. The present paper contains

Jan 1, 1945

By Persio P. Rosario

Crushing has proven to be of fundamental importance in mine mill integration at Highland Valley Copper (HVC). Highland Valley Copper has achieved large throughput and good quality control through the gyratory crushers by proper blast design and better gap control. The next step, in optimizing the mine mill relationship, is evaluating the crusher liner wear and its shape influence on performance and product size reduction. To do this a laser measurement device has been developed and data is being recorded on the concave and mantle liner wear. This paper will outline the work to date and indicate specific objectives of the work.

May 1, 2002

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

By P. K. Kaiser

3-D virtual reality (VR) visualization has opened new opportunities for complex 3D (x, y, z), 4D (x, y, z, t) or even nD data interpretation. The integration of common earth models (3D geologic data), mine models (3D excavations and stress), extraction models (1D time sequencing or mine sequencing) and nD monitoring data (e.g., seismic event parameters) into a common mining process model provides a platform for experts in various fields to better design, evaluate, monitor and modify mine plans throughout a mine?s life; from feasibility, through operation, to closure. Viewing seismic data in a stereoscopic VR environment within a mining process model offers data interpretation processes previously unavailable at lower dimensionality. MIRARCO has developed data analysis and viewing processes specifically designed to enhance microseismic and seismic data interpretation in a collaborative, immersive VR environment; bringing mine personnel and expert consultants together to evaluate data and make strategic decisions for cost effective and safe mining. Seismic events cause immediate hazards (rockbursts) and microseismicity causes gradual hazards through its cumulative effect in rockmass degradation. The focus of this paper is on understanding seismicity from a mine safety and mine planning perspective; in particular, how seismic migration patterns relate to the rockmass response to mining. The benefits of innovation in seismic data interpretation are significant, e.g., for hazardous work area identification, allowing better formulation of re-entry policies and workforce allocation planning, as well as allocation of effective support systems to strategic areas of elevated risk. Better understanding of the overall response of a mine to extraction also facilitates mine planning and design, assisting in reducing production costs and thus in enhancing profitability.

Apr 1, 2005

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

By James E. Cairelli

The NASA Lewis Research Center, under U.S. Bureau of Mines program direction, performed an assessment of alternative mobile power sources for mining applications. A wide variety of heat engines and energy systems was initially examined to ascertain which could be considered as potential alternatives to presently used power systems. The present mobile power systems are electrical trailing cable, electrical battery, and diesel - with diesel being largely limited in the United States to noncoal mines. Each candidate power source was evaluated in terms, of the following requirements: (1) Ability to achieve the duty cycle (2) Ability to meet Government regulations (MSHA certification) (3) Availability (production readiness) (4) Market availability (5) Packaging capability An initial screening reduced the list of candidates to the following: (1) Diesel (2) Stirling (3) Gas turbine (4) Rankine (steam) (5) Advanced electric (batteries) (6) Mechanical energy storage (flywheel) (7) Use of hydrogen evolved from metal hydrides This list of candidates was divided into two classes of alternative power sources for mining applications - heat engines and energy storage systems. A summary of each class follows.

Jan 1, 1981

By D. A. Livingstone

Abstract Golden Manitou Mines, Limited, nine miles east of the town of Val d'Or in northwestern Quebec, are presently milling, at the rate of 1,000 tons daily, a relatively complex 3.11-phide ore and producing, in decreasing order of value, zinc, silver, gold, lead, and copper. The products are a zinc concentrate, a silver-lead-copper concentrate, and a silver-gold precipitate from cyanidation. Although several independent pre-production metallurgical investigations into the treatment of the ore were carried out, current practice is different from any of the recommended methods and, while still leaving room for improvement, is considerably more effective than earlier performance. Flow-sheet developments from the commencement of operations in 1942 are dealt with briefly, showing the reasons for making numerous changes, the shortcomings of the various schemes tried, and, finally, covering data pertinent to present-day practice. From the recovery standpoint, silver has presented the greatest difficulty. The writer's association with the Company coincided with the start of production. Characteristics of the Ore The predominant metallic minerals present in the ore, in decreasing order of their abundance, are: pyrite, sphalerite, galena and chalcopyrite, with lesser amounts of argentiferous tennantite-tetrahedrite, arsenopyrite, covellite, bornite, and chalcocite. The sphalerite is mostly light in colour, sometimes colourless, and practically free from combined iron. Some of the sphalerite is very closely associated with minor amounts of pyrite, chalcopyrite, and galena. Pyrie is abundantly disseminated as medium to fine grains; more rarely it is massive and contains occasional grains of sphalerite, galena, and chalcopyrite.

Jan 1, 1952