Search Documents

By S. Simukanga, J. Masinja, P. A. Bepswa, A. N. Mwale

Screening is an important operation in dry and wet closed circuit mineral processing applications. Most of the operations have seen the benefits of using fine wet screens in primary grinding sections where the product is relatively coarse, and screens can handle the tonnage. Although many models are available, most of them are confined to dry and wet coarse screening applications. Most models do not give good predictions for wet fine screening. To facilitate model development, pilot plant tests were performed using a single deck Derrick Screen at aperture sizes of 45µm, 75µm, 106µm, and 150µm. Experimental data for a range of feed solids concentrations and flowrates was collected and used to calibrate the performance of the screen under the different operating conditions. The results showed that the performance of the screen deteriorated with an increase in feed solids concentration, and, similarly with an increasing feed flow rate. The percentage of fines carryover also increased with the reduction aperture size. The carryover was even more pronounced at higher feed rates and solids concentrations. A model was developed for predicting the performance of fine wet screening. Data from the test work was used to compare the actual and predicted results, and to calibrate the model. Additional independent data was used to validate the model and assess its limitations. This model will give an expected screen performance based on the initial feed conditions. It incorporates screen design parameters that allow for an estimation of a suitable screen size for a desired performance based on given feed conditions. This paper discusses; the results from the test work performed, the model development and its limitations.

Jan 1, 2016

By Yulin Zhou, WenFeng Li, Wen Chen

"In this article, with the help of the X-ray photoelectron Spectroscopy (XPS), a modern test method, all the characteristics of the chlorite,and adsorption collector A6 on the surface of chlorite have been studied. There exist abundant carboxylic C-O and C=O structures in the Carbon XPS atlas with strong adhesive ability after the reaction between new collector A6 and chlorite, which indicates that the ring structure and ether-base functional groups can strengthen the reaction between collector A6 molecule and chlorite surface. The results of XPS analysis indicate that the photoelectron spectroscopy peaks of Mg2p and Al2p moved towards low energy after collector A6 absorbed on chlorite surface, which indicates that chemical bonding through electron cloud transfer happened between collector A6 and Mg, Al ions of chlorite surface. The chemical reaction promoted the adsorption of A6 on chlorite surface and eventually improved the ability of A6 to float and collect chlorite.INTRODUCTIONThere are a large amount of iron-bearing silicate minerals such as chlorite in different types of gangue minerals in iron ore from different areas besides quartz (Yingyong et al, 2012; Qiang et al, 2009). There always exist Mg2+, Al3+ Fe3+ and other metallic ions due the isomorphic replacement among the irons of this kind of minerals. The dissolution often occurs on the surface of minerals with abundant metallic ions during grinding process, and some ions are exposed on the surface, such as Mg2+, Fe3+, Al3+, Si4+, which can increase the surface electrical behaviour of iron-bearing silicate minerals (Wanzhong & Chuanyao, 2002; Yuping et al., 2007), making it easy for the surface to react preferentially with the depressants such as causticizing starch which making it impossible for the surface to reach with conventional anionic fatty acid collector (Mowla et al, 2008). Thus, the beneficiation efficiency is dramatically decreased and the improvement of concentrate grade becomes very difficult. The conventional aliphatic acid collector has some defects such as poor selectivity, poor low temperature resistance, sensitive to water hardness, etc. Thus, the addition of synergist (Liu, & Yu, 2015) or other compound reagents (Zhou et al, 2015) can promote the adsorption of reagents to mineral surface, and improve the collecting capacity and selectivity of aliphatic acid collector to minerals. The addition of polar group to nonpolar group in aliphatic acid can improve the water solubility, dispensability and hard water resistance (Tian et al, 2013). The nitrogen atoms in amid ate aliphatic acid collector can adsorb on mineral surface by itself and supply coordinate electron which can form chelating keys to improve the collecting capacity of collector. There exist coordinate electron in oxygen atoms of ether acid collector, which, along with the oxygen on carboxyl compose chelate with metal (Luo et al, 2015). There are also exist some opinions that the ether acid can arrange into similar crown ether structure which can absorb on mineral surface. A new alicyclic unsaturated ether acid compounds collector A6 is adopted in this paper, the structural formula is listed in Figure 1. The A6 has a strong collecting ability to chlorite with strong water solubility and low temperature resistance."

Jan 1, 2016

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By Satoshi Honda, Mitsuru Shimizu, Tatsuji Nagao, Motoaki Kurisu, Hirokazu Izumi, Toshinori Takahashi, Hiroyuki Itoi

"1. INTRODUCTION Grade separation of roads and railway tracks is an effective method for solving traffic-related issues in cities. However, in urban areas where the existing traffic infrastructure is already overcrowded, construction of new roads often faces problems especially in the proximity of existing structures. This paper summarizes the construction plan and results of new road tunnel construction in the proximity of the piers of elevated tracks on the Tokaido Shinkansen railway.2. SUMMARY OF CONSTRUCTION AND ISSUES Auxiliary Route No. 26 as specified in the Tokyo urban plan is a project by the Tokyo Metropolitan Government, covering the construction of a new road with a total length of 22.3 km currently on the way to completion. In Shinagawa Ward, Tokyo, Auxiliary Route No. 26 is designed to cross the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line, so for this project, the East Japan Railway Company (JR East) was commissioned to design and build a road crossing under the railway tracks (Sumiyoshi Underpass). Figures 1 through 3 show a sketch of the Sumiyoshi Underpass. The Sumiyoshi Underpass was planned as a two-lane tunnel for vehicles, which was to cross under the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line at an angle of 70 degrees. The structure concerned is a single-story single-span box culvert structure with the following dimensions: 11.5 m wide, 7.7 m high and 31.6 m long. The Tokaido Shinkansen Line tracks were constructed on a girder-type elevated bridge built in the 1960s, and the foundation piles of the piers (P7 and P8) in the proximity of this crossing box culvert of RC structure were constructed using an earth drill method. The crossing structure for this project is located extremely close to the piers of the Tokaido Shinkansen railway tracks, with a minimal separation of 0.4 m, and the most significant issue of this project was construction in a manner that would not obstruct the normal operations of the Tokaido Shinkansen (Figure 4). Initially, we considered installing a temporary earth retaining structure in the proximity of the piers, cutting the ground and building an RC box, but concluded that it would be very difficult to apply this method because of probable excessive displacements in the Shinkansen railway piers. That is why we decided on the use of a non-open cut method in order to minimize the impact on the piers."

Jan 1, 2016

By V. T. McLemore

"Production of industrial minerals remains important to the rural economy of New Mexico. In 2014, some 240 mines were registered in New Mexico, including 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production of potash, perlite, zeolite, and travertine. Other production includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. New Mexico has potential for additional production of industrial minerals. One company is exploring for garnet. Cretaceous black sandstones in the San Juan Basin have drawn interest for titanium, rare earth elements (REE), and zircon. Other REE deposits are being explored. REE-Th-U veins are found in the Gallinas, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Recent exploration has occurred for beryllium in the San Mateo Mountains, Iron Mountain, and Victorio districts. Companies also are examining High-Ca limestone and High-Mg dolomite for potential development. Aggregate continues to be important in urban areas and along highways. INTRODUCTION Industrial minerals and rocks are literally the building blocks of our way of life and they are an exceptionally diverse and vital group of raw materials that underpin almost all aspects of human activity, infrastructure, and standard of living. Industrial minerals and rocks are used in the manufacture of many products, from ceramics to plastics and refractories to paper. Although industrial minerals permeate every aspect of daily life, their presence and their role are typically invisible. A widely used definition of industrial minerals and rocks is “any rock, mineral, or other naturally occurring substance of economic value, exclusive of metal ores, mineral fuels, and gemstones: one of the non-metallics” (Bates, 1975). This definition includes the important construction materials sector as well as specialized industrial minerals, but complex interactions between consumer industries produce a number of apparent anomalies to this definition. Some metals are included as industrial minerals because their use is industrial rather than as a metal. Sulfur is now predominantly extracted as a by-product of cleaning natural gas, one of the world's major energy fuels. Production of industrial minerals has been and remains important to the rural economy of New Mexico. Industrial minerals constitute nearly 40% of the more than $2.8 billion generated by mineral production in New Mexico in 2013 (Table 1, see APPENDIX). In 2015, some 240 mines were registered in New Mexico. This total includes 25 industrial mineral operations and 189 aggregate operations. New Mexico leads domestic production in potash, perlite, zeolite, and travertine. Other industrial minerals production from New Mexico includes aggregate, humate, pumice, gypsum, salt, common and fire clay, scoria, limestone, fly ash, cement, magnetite, silica, and decorative stone. Additional production statistics are in Harben et al. (2008). Major industrial mineral districts are shown in Figure 1."

Jan 1, 2016

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By Sylvie Lévesque, Cory Hennessey, Daniel Amariei

"In the iron ore industry, fine particles recovery is an important concern in terms of process performance and production costs. Continuous efforts are thus devoted to increase the efficiency in handling these fines.The Reflux Classifier (RC) is a relatively new technology that is mainly used in the coal and industrial minerals industries. The operating principle of this system is based on three mechanisms: hindered settling, autogenous dense medium and lamella settling. A preliminary evaluation of the Reflux Classifier technology for the beneficiation of iron ore fines was formerly done at the pilot scale using a RCTM300 unit. The good results obtained, using iron ore fines from screened spiral stream, made this technology very attractive for the iron industry. However, the high capacity of the RCTM300 unit (1–3 t/h), makes it unsuitable for R&D purposes. Thus, a smaller unit, the RCTM100, was assessed to validate the performances obtained with the RCTM300.This paper summarizes the performances obtained with the RCTM100. The challenges of the scale-down related to the adaptability of this technology to the iron ore industry are also presented. The results are compared to the RCTM300 performances, as well as benchmarked against sink-float tests. The metallurgical results on feed and products issued after the test work with the RCTM100 unit are supported by mineralogical characterization using a Mineral Liberation Analyzer.INTRODUCTIONFine particles recovery by physical separation means is a historical concern (Holland-Batt, 1992; Peukert and Wadenpohl, 2001; Srivastavaa et al., 2001; Majumder et al., 2003). Attempts to improve fine particle recovery at the laboratory, pilot and industrial scales adopting different strategies with traditional equipment or assessing new promising devices such as the MGS (multi-gravity separator), the Kelsey jig, the Yang jig, etc. (Kim, 2002; Goudreau, 2008; Kerr, 2012) have yielded variable success."

Jan 1, 2016

To meet the energy requirements, hydroelectric projects are planned and executed in many countries. Though these projects requires a high capital investment, the returns are regular with minimum maintenance after commissioning of the project and are ecofriendly. Bhutan is situated in the eastern Himalayas and covers an area of 38,394km2 (14824.01sq. miles. It is bordered by India in East, South and West and by Tibet in the North. The hydropower potential of the country is estimated at 30,000MW, out of which around 5% has been harnessed.

Jan 1, 2016

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

By Jurij Karlovšek, Marko Žibert, Scott Keniston

"SUMMARY The importance of information management was recognised in surface construction industry decades ago, and has increasingly being recognised through formal process and laws. Around the world, these laws and codes of practice are currently being drafted and enacted, to reflect the development of software tools and corresponding increasing adoption by industry. This paper deals with specifics of implementing information modelling in tunnelling business utilising BIM (Building Information Modelling) technology developed for buildings as well as similar technology developed for mining industry. Although BIM is recognized initially as a 3D digital representation of physical and functional characteristics of a facility, the real benefits come when complex capability through construction sequencing and even detailed programming (4D) and cost capabilities (5D) are included. INFORMATION MODELLING The Architecture, Engineering and Construction (AEC) industry requires the production of design and construction information, which involves the input from several teams. The tasks allocated to each team need to be carried out in a particular order and coordinated in order to benefit all those involved and the project itself; this is known as “collaborative working”. To ensure the quality, and guarantee that information can be used without change or interpretation, working processes and standards needs to be agreed upon or else it will hinder collaboration and have a negative impact on project delivery. Case studies show that the additional capital delivery costs due to uncoordinated, inaccurate and ambiguous information amounts to 20-25%. The solution to overcome these problems and improve collaborative working in a project is the adoption of BIM. It is a modern approach to the design, documentation, delivery, and life cycle management through the use of project information databases coupled with object-based parametric modelling. BIM requires traditional practices shifting from simple drafting to using 3D native models for building design environment. Additionally, it requires that models are equipped with information that has been traditionally decoupled in a text or other kinds of documents. The goal is not in creating a 3D graphic representation of design intent; rather, it is a comprehensive information management tool based on the simulation of design and construction build around a central repository."

Jan 1, 2016

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By Tom Barczak, Julian Restrepo, Zach Agioutantis

"The Alpha Foundation for the Improvement of Mine Safety and Health, Inc. (Foundation) was established as part of a Non-Prosecution Agreement (Agreement) entered in December 2011 by the United States Attorney's Office for the Southern District of West Virginia, the United States Department of Justice and Alpha Natural Resources, Inc. (""Alpha"") and Alpha Appalachia Holdings, Inc. This Agreement was related to the explosion at Upper Big Branch Mine, an underground coal mine owned by Performance Coal Company, a former affiliate of Massey Energy Company, which Alpha acquired in June 2011. Pursuant to that agreement, Alpha agreed to establish a trust to fund projects designed to improve mine health and safety by providing $48,000,000 into the trust. The mission and vision of the Foundation are as follows:Mission: To improve mine health and safety through funding research and development projects by qualified academic institutions and other not-for-profit organizations.Vision: To enable miners in the future to be free of work-related injury or disease by the implementation of the results of the projects funded by the Foundation and undertaken by the best researchers from any discipline that can contribute.The focus of the research effort is not limited to coal mine explosion prevention, and in fact encompasses the entire spectrum of health and safety, addressing issues in both underground and surface mining operations in all mining sectors. Four major focus areas are identified (see Figure 1): 1) Health and Safety Interventions; 2) Mine Escape, Rescue, and Training; 3) Safety and Health Management and Training; and 4) Injury and Disease Exposure and Risk Factors.The Foundation is seeking to expand the knowledge base of mining safety and health information that can lead to resolving complex mining problems. To that end, the projects funded by this effort are designed to provide a spectrum of knowledge potentially encompassing the following:• Surveillance data - Collect and analyze surveillance data that better documents the prevalence and trends of occupational safety and health across the mining industry."

Jan 1, 2016

By F. McCarthy, R. McDonald, G. Woodbridge, G. Brock, D. Robinson

"The Direct Nickel process is a hydrometallurgical technology being developed to treat nickel laterite ores by leaching at atmospheric pressure. The leaching process uses nitric acid in a relatively large excess, is thus non-selective, and much of the soluble iron goes into solution. The first stage of solution purification is iron hydrolysis and the Direct Nickel process utilises the colligative properties of the pregnant leach solution (PLS) to enable the removal nitric acid of varying concentrations via distillation. Once sufficient acid has been removed, the boiling point of the solution is increased allowing high temperatures (up to ~170°C) to be achieved under atmospheric pressure. The higher temperatures initiate the precipitation of the iron primarily as hematite and allow the removal of the acid generated by the hydrolysis reaction. The rejection of the iron is near complete with solution tenors typically falling from 65 g/L Fe, or more, to less than 50 mg/L Fe. The separation of clean nitric acid from the PLS at this stage allows for relatively simple acid recycling. A hematite product with iron content above 60% could also provide an extra revenue stream.INTRODUCTION The Direct Nickel (DNi) Process is a novel hydrometallurgical processing route designed to treat all types of nickel laterite ores in a single flow sheet using nitric acid under atmospheric conditions. A simplified flow sheet is shown in Figure 1.Between 2007 and 2012 the process was developed and refined at Direct Nickel’s laboratory within the CSIRO Minerals’ facilities in Perth, Australia, and in 2013 a series of pilot plant trials were run under continuous operating conditions. The process is designed to treat both limonite and saprolite in the same flow sheet, and after comminution, the blended ore is mixed with nitric acid and leached just below boiling point in agitated atmospheric leach tanks. The acid is added in excess, so typically for a blend of limonite and saprolite the acid addition can be in the order of 1.8-2.0 t acid/t dry ore. After a residence time of between 4-6 hours the majority of the soluble metals have leached into solution and the insoluble leach residue is separated from the pregnant leach solution (PLS) via counter-current decantation."

Jan 1, 2016

By Henning Schwarz, Faisal Al Arifi, Anas Almousa

"The Riyadh Metro Project forms part of a complete new public transport system integrated in the urban planning and development of the fast growing capital city of the Kingdom of Saudi Arabia. The Design & Build project consists of 176 km of a new metro network with 57 km of double track single tunnel infrastructures, spread over six metro lines. During the design phase, geological, hydrogeological, geotechnical and geophysical site investigations were undertaken to chart the, previously uncharted, underground construction space. Different TBM solutions were selected for implementation taking due consideration of the ground conditions of each metro line. The results obtained from deep excavations for underground stations and analysis of the TBM tunneling data will be used as key input for future tunneling projects in the Riyadh and the Kingdom of Saudi Arabia. The present paper details the design conditions and presents the solutions for large diameter tunnels in karstic limestone. INTRODUCTION The High Commission for the Development of Arriyadh was established in 1974 as the organizational, planning, executive and coordinating body responsible for the development of Riyadh. Arriyadh Development Authority (ADA), established in 1983, is the High Commission’s executive, technical and administrative arm. The ADA is responsible for implementing the High Commission's organizational, planning, executive and coordinating decisions and missions (ADA 2015). One of the remits of the ADA is the preparation and execution of a transport plan for the city. The metro network is planned to be the backbone of the public transport system developed as part of the King Abdulaziz Project for Riyadh Public Transport in Riyadh. With six lines and a total length of 176.5 km (Table 1) and 85 metro stations, the metro network will cover most of the densely populated areas, public facilities, and the educational, commercial and medical institutions. The network will connect the King Khalid International Airport, the King Abdullah Financial District, main universities, Riyadh downtown and the public transport center. The public transport plan includes a future bus network with 22 lines on 1200 km and 6765 stops that will be the main feeder for the Riyadh metro network; it will also be the main mode of transportation within and around Riyadh districts (ADA 2015)."

Jan 1, 2016

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

"Geoscan is used for multi-elemental analysis of conveyed bulk materials in the minerals industry with proven performance and demonstrated paybacks of weeks or months in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering, mineralogy and dust levels. Increments of typically two minutes are accurately measured and provide the plant operators with tonnage weighted results of contained elements. Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Crushed ore increments can be diverted based on composition, such as diverting waste for disposal or marginal material to a stockpile for separate processing. Bulk sorting allows material to be placed into relevant stockpiles for subsequent blending to achieve consistency for process feed. Parameters used for decisions may be primary metal content, deleterious component content, other process parameter, or a combination of these. Process parameter may be the elemental ratio between critical components, e.g. Cu:S ratio, basicity, or the content of an “indicator” element (such as Si indicating material hardness). Benefits will be discussed based on case studies in copper and iron ore.IntroductionAs operators of process plants strive to remain competitive as capital and operating costs increase and commodity prices fluctuate, more focus has been directed at incremental performance improvements at incremental cost rather than major expansions to increase output. The philosophy of working smarter allows plants to adopt technologies proven in other industry sectors to minimise risk. This paper discusses one such technology that the minerals sector is adopting and has found to be safe, reliable and accurate with paybacks of weeks in most applications. New applications continue to be found and major benefits realised at various stages in the processing and handling of ores and products."

Jan 1, 2016

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

By Pierre De Pasquale, Gilles Jauffret, Ricardo Chavez

"When blasting in quarries or mines, the main source of inconsistent results is directly related to thenon-homogeneous energy distribution through the rock-mass volume. This variation has differentorigins: drilling deviations, geometry differences from one borehole to another (burden, spacing ...),and inherent geological conditions."

Jan 1, 2016