Search Documents

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By Joey Hoang, Robert Johansson, Tapani Keronen, Mikael Jåfs, Jani Jansson, Mikko Korpi

At the Copper 2016 conference in Kobe, Japan, Outotec introduced a vision for the year 2020, wherein smelting would make use of four digital cornerstones: intelligent instruments, advanced process control, improved information management and transparency of and access to data. Since then, this vision coined the phrase “Fully Automated Smelter” with the mission promising a concept where no manual actions from human operators would be needed during normal smelter operations. Replacing repetitive physical work, collection and analysis of everyday production data has a great potential for further automation and will provide productive ways to improve efficiency and safety of smelters in the future. Therefore, a lot of emphasis has been put into developing solutions to automate these tasks and to move people out of harm’s way. A lot of new equipment, systems and optimization tools are under development. In addition, a lot of effort is going into developing dynamic process models and advanced control systems to interface with the plant automation systems. The goal is to integrate all these concepts to meet Outotec’s Fully Automated Smelter vision. This paper will cover these latest achievements toward this vision and introduce the near-future of digital smelting. INTRODUCTION As is well known already, the humankind is currently experiencing a change, extent of which is broadly studied by the governmental, educational and industrial institutions and parties. The wellbeing and quality of life have traditionally been improved alongside the developments in industrial production, which is now about to enter its fourth revolution. Therefore, the current change is often described as fourth industrial revolution, or industry 4.0 (or industrie 4.0, as named by Acatech, 2013) and can be considered anything from small incremental development to a ground-breaking global reset that will affect everyone’s lives. Many seem to agree, that the scale of change will indeed be big, even significantly bigger than the three industrial revolutions before it (Pellini, Weyrauch, Malho & Carden, 2019; Geissbauer, Vedso & Schrauf, 2016; Jansson, Bjorklund, Lahtinen, Heinonen, Jafs & Fagerlund, 2016).

Jan 1, 2019

By D. Tetsuka, H. Okamoto

The amount of impurities to be processed in a copper smelting process has increased for recent years because of an increase in the electronic scrap amount. It has been found that Sb and Ni effect on the operation of our copper electrorefining process. It is found that the current efficiency of the copper electrorefining tended to be decreased as the Ni concentration in the electrolyte increased. The passivation of the process seemed to be more related to SO4 concentration in the electrolyte rather than the Ni concentration in it. The current efficiency decreased when the Sb content in the anode was high. A high Sb content in the anode caused easy passivation by forming a gel-like film in the slime layer. We have developed a method to for see the anode passivation in a short time while generating a slime layer. We confirmed the tendency of passivation through the experiment of changing Pb content in anode. Passivation was easily occur with an increase in Pb content in the anode. The amount of slime increased as the Pb content in the anode increased. This suggests that passivation was facilitated because liquid diffusion near the anode was inhibited. INTRODUCTION The amount of impurities to be processed in copper smelting has been growing in recent years because the amount of electronic scrap has increased. Figure 1 shows that the contents of Sb and Ni in copper anodes have increased since 2007.High Sb and Ni contents in the copper anode decreased the current efficiency of the process and made the quality of copper cathode poor because of the anode passivation and the formation of floating slime in the electrolyte during electrorefining. If these influences of impurities are suppressed, it would be possible to make copper electro-refining current density higher and to process much amount of electronic scrap. We examined the components of our copper electro-refining process like anode composition, slime properties and electrolyte composition, and investigated the mechanism by which Sb and Ni affect passivation and current efficiency. When examining the influence of Ni, we noticed that the SO4 important. The effect of SO42 – was also discussed

Jan 1, 2019

By William M. (Bill) Shaver

"The author will review the early history of shaft sinking as well as focus on the improvements made in shaft design and construction over the last fifty years (1970 to 2019) to predict how shaft sinking will change over the next fifty years and describe what the shaft sinking world might look like in 2070. INTRODUCTION It is a great honour to be one of your keynote speakers for the Fourth International Conference on Shaft Design and Construction being held in Toronto in November 2019. This is one of the opportunities we have to thank the Mining Companies of the world as well as the industries and companies we serve for their support of the mining contracting and shaft sinking business of Canada and the world at large. Many of these companies are represented here today. Without your support many of the innovations we will talk about today would not be possible. We would also like to thank all the companies that work with us in our business including all the contractors and suppliers who provide the various services we require. These include equipment manufacturers, engineering companies, project management companies and suppliers large and small who cater to our every need as quickly as possible. Without all these partners we would not be as good as we are. Many of these companies are our sponsors this week. Thank you from all of us! This is also an appropriate time to pause and think about those Shaft Sinkers we have lost and those who have been injured on our projects around the world. Please bow your head and remember the Shaft Sinkers you have worked with, who did not return home or those who returned home injured. Think about how we can continue the work of making shafts safer every day as we go forward with our projects so everyone goes home to their families safe and sound. Pause for a minute and thank you. The subject matter we have chosen to discuss today is “Shaft Sinking in the Next Five Decades”. How will the work be done, how fast will it be done, what will it cost, and why we think this may occur? It is appropriate to consider this over the next few days with this auspicious group we have assembled. Today, we will look back at all the advances that have been made over the last many years and look ahead to the future to attempt to predict what shaft sinking will look like in 2070. When I look around the room I recognize that many of us will not be around then so we need not worry about being wrong. Suffice it to say that the next 50 years will be very interesting and exciting for the shaft sinking business."

Jan 1, 2019

By A. Mazhary, T. Huff

Sensor-based ore sorting technology is a growing area of interest due to lower-grade ore deposits and higher costs of processing, among other reasons. Among the sensors currently utilized in the particle sorting industry, X-Ray Fluorescence (XRF), as the only sensor with elemental analysis capabilities, has always attracted more attention. Currently, the bench-scale amenability tests for this sensor are performed using hand-held XRF analysers. However, this testing method overestimates the performance of the XRF sorter, and therefore, the results from these tests can be misleading and are often mispresented. The work presented here was conducted on a copper mine and investigates how the sensor’s sensitivity to copper deteriorates under different testing methods. This work compares and correlates the results of an Olympus hand-held XRF analyser, static, and dynamic sorter responses with the actual grades of the rocks. The results confirmed that, the sorter response was extremely prone to blind spots. Furthermore, the results demonstrated that although the static sorter’s responses were comparable in terms of rock identification to those of the hand-held XRF analyzer and assays, the accuracy of the dynamic sorter response deteriorated both as a function of grade of the rocks as well as the potential for blind spots. INTRODUCTION Sensor-based sorting technology has been gaining increasing attention even by larger mining corporations as ore grades decrease, deposits get deeper and therefore cost of mining and processing increases. There are various types of sensors that are currently being used in the particle sorting industry such as X-Ray Transmission (XRT), Color, Electromagnetic (EM), Near-Infrared (NIR) and others. However, none of the sensors are capable of identifying and quantifying particles by the elemental content, except for X-Ray Fluorescence (XRF). XRF is a non-destructive, surficial analytical technique used to measure elemental composition of materials. X-ray fluorescence happens when a secondary x-ray (fluorescence) is released after a sample is bombarded by a primary x-ray source. From a sorting perspective, the most common and expected issues that are associated with XRF sorting are lower throughputs compared to other sensors due to particle presentation limitation as well as the need to wash the material before introducing to the sorter. However, one important issue that is mostly neglected is how the amenability tests are performed and how realistic the obtained results are. Current amenability test procedure utilises a handheld XRF analyser (such as an Olympus InnovX, as used in this work) on multiple, generally 4, sides of the rock and uses the average measured grade as a criterion for separation. While this is a widely accepted technique, it fails to consider some important factors such as exposure time and the distance between the sensor and the particle. These factors can significantly affect the sorting outcome.

Jan 1, 2019

By Sayantan Chakraborty, Kaushik Dey, SaKaushik Dey tyabrata Behera

Drilling and blasting is a popular excavation technique in the drift of underground mine. Faster completion of drift reduces the gestation period and thus longer blast pulls are attempted with longer drill holes. This compels the blasters to initiate higher charge quantity with higher confinements and ultimately results into blast-induced cracks beyond the desired periphery line of excavation. Assessment of the extent of these crack networks is difficult and often neglected. Near-field ground vibration models are often used as damage predictors (Dey, 2007, Yang et.al 1993, Holmberg et. Al 1979) but not necessarily deals with the positions of the cracks. Qualitative measurement of actual damage extent often measured using some geophysical tools, namely, P-wave velocity (Tezuka, 1995), seismic imaging (Dey, 2011), bore hole pressure monitoring (Brent and Smith, 1996), electrical resistivity (Grady and Kipp, 1993), GPR (Adams et.al, 1993) etc. Ground Penetrating Radar (GPR) is a similar geo-physical tool, which uses Electro-magnetic (EM) pulse for characterizing the medium. Similar to other geo-physical tools, GPR also comprises of a transmitter and one/multiple receivers to generate the EM pulse and receive the same after reflection/refraction from the medium(s) respectively. After its development in 1970s, GPR gained increased popularity due to its application in many important fields, namely, identification of buried objects, geological characterization, identification of geological disturbances etc. Thus, it is felt that GPR technique can be used to detect the invisible cracks inside the rockmass from the rock surface (wall and roof) itself. Understanding the same, field experimentations are carried out in an underground manganese mine in Central India, which operates on the ‘cut and fill’ method of mining at a depth of around 300m from the surface. Wedge cut blasting is carried out in the horizontal drifts of the mine using suitable blast design. A 1.6 GHz antenna was used for the GPR scanning, in which GPR transmitter transmits signals predominantly of the said frequencies. The signals get reflected back from any type of interfaces between materials in the target area, with different dielectric properties and is received by the receiver part of the ‘trans-receiver’ antenna and memorized in the Data Acquisition Unit (DAU). The data acquired is processed using a software. Ground vibration monitoring of the blasts are also carried out to develop a vibration predictor. The numerical analysis of near-field vibration predictor model results into the estimated vibration levels at the point of identified cracks. Introduction

Jan 1, 2019

By D. Stone, R. Pakalnis, B. Seymour

Most mines using backfill routinely carry out quality control (QC) testing of backfill mixes with unconfined compression test cylinders. This is true for paste operations, hydraulic fill operations, and cemented rockfill operations worldwide. However, a large number of mines simply do not prepare and test the backfill samples in a consistent manner and fail to properly analyze or interpret the test results. Conventional concrete test criteria are not applicable given the differences in the mix constituents and the fact that a large number of the backfill QC test cylinders typically fail to achieve the target strength. Standard industry practices are needed to improve the analysis and interpretation of QC test results and to provide a better means of determining if the backfill is achieving its intended target strength. This paper will attempt to lay the groundwork for standard industry practices and will address several key questions raised by operators, such as how laboratory test data compares to in-stope performance, and how many QC tests should fail before a red flag should be raised. INTRODUCTION Although paste backfill is widely used throughout the mining industry, cemented rockfill (CRF) remains as the backfill of choice in places like Nevada where very poor ground conditions mandate the use of underhand mining. The safety and stability of undercut entries beneath backfill is a function of the quality of the cemented fill, which is typically assured through routine quality control testing. In the absence of a backfill quality standard, most mines rely on concrete standards to design and interpret their backfill quality control programs. In the USA, these standards are developed and published by organizations such as the American Society of Testing and Materials (ASTM) and the American Concrete Institute (ACI). However, the application of these standards to cemented backfills can be very difficult owing to the high degree of variability in backfill mixes and the resulting variability in test results. To illustrate, the concrete industry standards denote that an acceptable (passing) test result occurs when the average strength of the duplicate test cylinders exceeds the target strength and no single test result deviates from the target strength by more than 10% (ACI 214R). Remedial measures must be taken if three consecutive tests fail. With mine backfills, it is safe to say that these criteria are rarely achievable. A further, more dramatic example is the accepted coefficient of variation for concrete QC cylinders. According to ACI 214R, the coefficient of variation (CV) should range from below 3% (excellent rating) to above 6% (poor rating). However, if this analysis method is applied to several backfill QC databases from operating mines, coefficients of variation are calculated on the order of 50%. Clearly, there is a need to develop better industry practices for assessing the quality of mine backfill and to assist mine operators with the interpretation of test results and the development of action plans in the event of undesired outcomes.

Jan 1, 2019

By D. Parks, A. Miller, M. McNinch, R. Jacksha, H. Nickerson

Each year hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s implementation of an IoT-based intelligent machine monitoring system to improve safety during operation and maintenance at a concrete batch plant. INTRODUCTION Of the hundreds of machinery-related accidents occurring every year in the mining industry, incidents involving stationary machinery at surface mines continue to be amongst the most frequent [1]. A National Institute for Occupational Safety and Health (NIOSH) study showed that the majority of fatal accidents involving stationary machinery at surface mines occurred at sand and gravel (38%) and stone (26%) operations. Of these accidents, entanglement in conveyor components were the most common cause of fatal accidents (48%) [2]. The same study stated that one-third of these accidents involved improper lockout/tagout (LOTO) procedures as a contributing factor. The U.S. Mine Safety and Health Administration (MSHA) acknowledged this problem, stating in a recent request for information (RFI) [3]: “Since 2007, there have been 17 fatalities related to working near or around belt conveyors, of which 76 percent were related to miners becoming entangled in belt drives, belt rollers, and discharge points. Factors that contribute to entanglement hazards include inadequate or missing guards, inadequate or an insufficient number of crossovers in strategic locations, and/or inappropriate lock out/tag out procedures. Systems that can sense a miner's presence in hazardous locations; ensure that machine guards are properly secured in place; and/or ensure machines are properly locked out and tagged out during maintenance would reduce fatalities [3].” In response to this problem, NIOSH’s Spokane Mining Research Division (SMRD) is exploring the potential application of Internet of Things (IoT) technologies to provide cost-effective intelligent machine monitoring systems for improved worker safety [4, 5]. SMRD partnered with Central Pre-mix CRH Company (Central Pre-mix) to develop and install a proof-of-concept wireless IoT solution to monitor machinery and conveyors during operation and maintenance. The primary goals of the system were to provide real-time monitoring of access points and facilitate the planning and execution of LOTO procedures

Jan 1, 2019

By A. Roca, G. Ríos, I. Ruíz, M. Cruells

Flash Smelting Furnace (FSF) hot dust-laden is cooled in a waste heat boiler (WHB) and then dedusted in electrostatic precipitators (ESP’s) before being treated, together with the Peirce Smith Converters off-gases, in the sulfuric acid plants for SO2 removal. FSF dust is sulfated by SO2 and O2 in the WHB. Typically, 70% of the dust from the FSF drops in the WHB while the remainder is caught in the ESPs. The collected dust is recycled to the FSF for Cu recovery. Some smelters have developed hydrometallurgical treatments to recover Cu from the dust; impurities, such as As and Bi, are bled as leach plant residues. This paper presents a study (laboratory scale), of leaching the FSF dust, generated in Atlantic Copper Smelter using the weak acid bleed from the gas scrubbing/cooling section (GSCS) of sulfuric acid plants. Leaching was performed with 0.5 mol L-1 sulfuric acid concentration, 60ºC, and a solid/liquid ratio 1/3. After leaching, H2O2 was used for arsenic and iron oxidation. pH was adjusted for precipitation of arsenic and iron as scorodite or as scorodite and arsenical jarosite. The precipitation was carried out at 95ºC during 3-6 h. Liquids after precipitation are suitable for subsequent treatments of electrolysis. INTRODUCTION The copper smelter dusts are usually recirculated totally or partially to the flash furnace. This practice increases the amount of impurities feeding the furnace. Some authors have developed processes for treatment of these materials for copper and zinc recovery and for arsenic, antimony and bismuth inertization. The processes for the treatment of copper smelter dusts can be pyrometallurgical (Yu, 1987; Carter, Vance, Aldridge, Zaw, & Khoe, 1994; Fu, Jiang &Wang, 2000), hydrometallurgical, or mixed processes (Yin et al, 1992; Mulale, Mwema, & Mashala, 1999; Gorai, Jana, & Khan, 2002). Hydrometallurgical processes have been extensively studied and, in some cases, applied to an industrial scale. The most important chemical reagent proposed for leaching the dusts has been sulfuric acid (Roman-Moguel, Plascencia, Pérez, & Garcia, 1995; Gabb, & Evans, 1997; Larouche, 2001; Morales, Cruells, Roca, & Bergó, 2010; Cáceres, Cruells, Morales, & Roca, 2012; Ecometales, 2013; Yang, Fu, Liu, Chen, & Zhang, 2017). Processes developed in alkaline media, and in some cases with the presence of sulfide, have also been carried out (Gabler, & Jones, 1988; Morales, Hevia, & Cifuentes, 2009; Alguacil, Garcia-Diaz, Lopez, Rodriguez, & Alonso, 2013), as well as by using a bioleaching process (Massinaie, Oliazadeh, & Seyed Bagheri, 2006; Bakhtiari, Atashi, Zivdar, Seyedbagheri, & Fazaelipoor, 2011).

Jan 1, 2019

By C. Salcedo, J. Vallance, J. Sáez, M. Robles, J. Spangenberg, S. Rosas, L. Fontboté

The Tambomachay ore deposit (13°28'36.78"S, 71°57'35.98"W, about 6 km north of the town of Cuzco, Peru) consists of Cu hosted in arkosic red beds of the Kayra Formation (Lower Eocene). Bornite, chalcopyrite, chalcocite, covelite, digenite, malachite, and chrysocolla occur disseminated in thin layers and in veinlets. The occurrence of the copper ores in a part of the red bed sequence containing green reducing layers, the presence of organic matter in interstices between the hypogene sulfides, and the sulfur composition of the copper sulfides (δ34S values between -16.9 and -12.4‰ vs VCDT) pointing to bacterial sulfate reduction, are strong arguments to propose that mineralization was caused by copper-bearing oxidizing saline basinal fluids that precipitate copper sulfides when they meet reduced sulfur in an organic matter-rich horizon. Faults parallel to the regional Tambomachay Fault could have acted as feeders for oxidizing basinal copper-bearing fluids. Fluid migration was probably driven by tectonically-induced topography gradient. INTRODUCTION A number of red bed Cu occurrences are known in the Cuzco region in the early Eocene – early Oligocene San Jerónimo Group (Gregory, 1916; Carlotto et al., 1996, 2011; Loza et al., 2004). In the past, copper ores were extracted in several small-scale mines in the surroundings of Cuzco, including Tambomachay, Tipón, and Zurite in the Cusco province and Ushpa, Guilda, Giovanna, and Langui in the Sicuani Province. The abandoned Tambomachay Mine (13°28'36.78"S, 71°57'35.98"W), about 6 km to the north of the town of Cuzco (Romero et al., 2015; Salcedo et al., 2017, Fig. 1) was chosen as the main site for the present research aimed to better study the genesis of these copper occurrences. Results deriving from fieldwork, microscopic characterization of ore and host rock, and sulfur isotope determination suggest that the key factor for the genesis of the copper ores is that copper transported by oxidizing basinal fluids is trapped by reduced sulfur of bacteriogenic origin located in a part of the red bed sequence that shows intercalatins of green reduced horizons.

Jan 1, 2019

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By John C. Stankus, Xiaoting Li

"Underground structures such as square/arch steel sets, king beam structure, etc. are widely used for the roof support in underground mines. In designing and calculating the required carrying capacities of these underground structures, how to identify the potential rock loads on the structures over long term is a challenging question for ground control engineers. Based on design practices of both surface and underground structures, the authors have designed and applied appropriate load factors in underground structural design projects to accommodate different rock types, entry/intersection dimensions, roof geologic conditions, availability of roof bolts and water, etc. Classification of load (reduction) factors for large-span underground intersections are presented for reference. Success of designed underground structures in effectively controlling roof stability over years indicates the applicability of the load factor concept for underground structural design, and its same significance as of the load factor specifications in ASCE/SEI 7-10, ANSI/AWC NDS (2015), and AASHTO LRFD Bridge Design Specifications (2012). The load factor concept will facilitate ground control engineers to appropriately utilize popular structural design software, such as RISA-3D or -2D to efficiently design and analyze underground structures.LOAD FACTORS IN STRUCTURE DESIGN APPLICATIONSIn structures, loads cause stresses, deformations, and displacements. Assessment of their effects is carried out by the methods of structural analysis with the help of load factors. Loads can be increased or decreased by load factors to meet the requirement that design strength be higher than maximum loads. For example, in designing a staircase, a dead load factor may be 1.2 times the weight of the structure, and a live load factor may be 1.6 times the maximum expected live load based on the Load and Resistance Factor Design (LRFD) method. These two “factored loads” are combined (added) to determine the “required strength” of the staircase. Some typical load (adjustment) factors used for structural design are as follows:"

Jan 1, 2019

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By T. G. Joseph, R. K. Soni, M. Curley

"Rapid dampening suspension is a proposed suspension design for ultra-class haulers that is intended to avoid metal-to-metal contact inside a strut and under shock loading, thus improving ride quality and ameliorating fatigue loading issues on a hauler structure. Laboratory testing has shown the ability of the proposed design to reduce the opportunity for bottoming out, that is, metal-to-metal contact between the colliding ends of oleo-pneumatic, two-piece suspension struts during the compression cycle. This paper predicts the performance of a full-size rapid dampening suspension strut by applying scaling rules to test the proposed design based on a set of field data from a Caterpillar 797B ultra-class haul truck operating in the oil sands region of the province of Alberta, Canada. The predicted performance of the suspension strut is compared to that of the original equipment manufacturer model, which was monitored on board the truck during field data collection. ¦ KEYWORDS Haul truck, Original equipment manufacturer (OEM), Rapid dampening, Strut, Suspension RÉSUMÉ La suspension à amortissement rapide est une conception de suspension proposée pour des camions de transport de catégorie ultra-class (des engins dont la charge utile dépasse les 320 tonnes métriques), visant à empêcher un contact métal sur métal à l’intérieur d’une jambe de suspension et dans des conditions de choc au chargement. Elle améliore la qualité du roulement et les problèmes de charge de fatigue sur la structure d’un camion de transport. Les essais en laboratoire ont confirmé que la concep¬tion proposée évitera au cylindre interne de heurter le cylindre externe, autrement dit empêchera le contact métal sur métal des jambes de suspension oléopneumatique en deux parties pendant le cycle de compres¬sion. Cet article prévoit la performance d’une jambe de suspension à amortissement rapide à taille réelle en appliquant les lois d’échelle afin de mettre à l’essai la conception proposée, sur la base d’une série de données de terrain relatives à un camion de transport 797B de catégorie ultra-class de Caterpillar (aujourd’hui remplacé par le nouveau modèle 797F) utilisé dans la région des sables bitumineux de la pro¬vince de l’Alberta, Canada. On compare la performance prévue de la jambe de suspension à celle du modèle du fabricant d’équipement d’origine (FEO), qui a été contrôlée à bord du tombereau pendant la collecte des données de terrain. ¦ MOTS CLÉS amortissement rapide, camion de transport, fabricant d’équipement d’origine (FEO), jambe de suspension, suspensionINTRODUCTION Research basis for the paper This paper is based on the unpublished MSc thesis work of El-Sayed (2003), Santos (2007), and Soni (2009) under the direction of Dr. Tim Joseph within the oil sands–equipment interactions program (OsEIP). OsEIP is part of the Alberta equipment–ground interactions syndicate (AEGIS) surface mining research group, School of Mining and Petroleum Engineering, University of Alberta. The aforementioned work spanned a decade of progressive studies into rapid dampening suspension systems, leading to the scale performance indications highlighted here. Although this paper uses a specific Caterpillar 797B suspension strut for field monitoring and as a basis for scale prediction of a modified rapid dampening suspension strut design, the design scaling principles used here could be applicable to any such design change consideration for an oleo-pneumatic suspension system."

Jan 1, 2019

By G. A. Gamble

"The inlet air velocity profile of any surface mine ventilation fan is an important factor when designing the connecting ductwork from the mine shaft collar to the fan. Deficient fan performance can be the result of ductwork that adds unnecessary pressure loss and/or adversely influences the fan inlet air conditions (velocity profile). The need for optimized inlet air conditions begins with discussing the process of performance testing during the development of the fan performance curve. Additional discussions include design of the shaft collar connection and the connecting ductwork. A preferred design of ductwork for parallel fan installations will be illustrated.INTRODUCTIONThe inlet air velocity profile of any surface installed mine ventilation fan is one of the most important factors to consider when designing the connecting ductwork from the mine shaft collar to the fan. Oftentimes deficient fan performance can be traced to poorly designed ductwork that adds unnecessary pressure loss and/or adversely influences the fan inlet air conditions (velocity profile). Such designs may lead to added power requirement, excessive vibration and noise, and reduced fan performance.Understanding the need for optimized inlet air conditions begins with discussing the process utilized when factory testing takes place during the development of the fan performance curve.Additional discussions include design considerations for the shaft collar connection, the connecting ductwork, and fan inlet. Illustrations of cost savings and pressure losses will be included for audience consideration. The design of ductwork for parallel fan installations on the surface is another issue that requires consideration. A preferred method will be illustrated.The selection of accessory components, such as self-closing doors, can also add to the potential for reduced fan performance. Several components will be discussed.An elementary presentation of the Air Movement and Control Association (AMCA) Standard 201 “Fans and Systems” will be included to provide background for those audience members that want additional technical explanations of the need for a uniform inlet air velocity profile at the fan inlet."

Jan 1, 2019

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay, Cicek Sena, Zhao Haochen

"Analysis of Longwall Pillar Stability (ALPS) and Analysis of Retreat Mine Pillar Stability (ARMPS) treat the pillar as a passive structure that is designed to carry overburden dead-weight. This dead-weight is calculated by simple rules based on the geometry of the mining, such as “tributary area theory,” “pressure arch theory,” and “abutment angle theory.” Although the pressure arch loading approach indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology of the overburden in load calculations. The relationship between successful pillar layouts and overburden geology can be incorporated into the load calculation by using the Ground Response Curve (GRC) approach.This paper introduces the GRC modeling methodology to investigate the effect of overburden geology and excavation geometry on load transfer mechanisms using seven field measurement case studies from four U.S. mines. It was also shown that the modeling methodology used to derive GRC in this study approximates mining-induced stresses and deformations within 5% of the values measured in the field.INTRODUCTIONFrith and Reed (2017) stated that current state-of-the-art pillar design methods ignore the overburden mechanics and use estimated dead-weight of overburden to compute pillar sizes. In the United States and around the world, overburden loading is typically estimated by simple geometric rules, generally with the tributary area theory (TAT). The specific overburden mechanics, structural competence of the overburden strata, geology, in situ stresses, and overburden/pillar interactions are typically ignored. However, these important mechanical responses affect the stability of the mine pillars and openings; therefore, they also affect the safety of the mine workers.Research conducted by the National Institute for Occupational Safety and Health (NIOSH) after the Crandall Canyon mine disaster (Esterhuizen, Mark, and Murphy, 2010) showed that small panel width-to-depth ratios and stiff-strong overburden result in a reduction of the observed pillar loads, much smaller than the TAT estimate. In fact, as a response to the Crandall Canyon disaster, Mark (2010) implemented a pressure arch loading approach into the latest ARMPS program to recognize the inherently greater stability of narrow panels at depth. The pressure arch approach is a first logical step to introducing non-tributary area loading into the practical ARMPS program. Although the pressure arch loading indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology and mechanical response of overburden in the load calculations."

Jan 1, 2019

By V. Prostakova, M. Shevchenko

The copper smelting gas / slag / matte / metal / solids system with the Cu-Fe-Ca-Si-O-S major elements has been a long-term focus of the present overall research program using integrated experimental and modelling approach for the phase equilibria characterisation and development of a thermodynamic database. A systematic investigation of phase equilibria of slag systems in equilibrium with Cu metal is providing information for systems where copper coexists in slag with lead, zinc, and aluminium oxides as major components. Experimental studies involve high-temperature equilibration of synthetic samples; rapid quenching; and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). Particularly important feature of the present study a wide range of temperatures (660-1670°C) being characterised that reveals major inconsistencies in the existing thermodynamic description of the multicomponent system, and allows to establish the thermodynamic properties from phase equilibria in a reliable way. FactSage-based thermodynamic modelling is integrated with experimental research. Initial thermodynamic assessments are used to identify priorities for experiments, planned to provide specific data for thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved, in particular in the PbO-Cu2O-SiO2, ZnO-Cu2O-SiO2, and Cu2O-CaO- Al2O3 systems in equilibrium with metallic Cu. INTRODUCTION Slags high in lead and copper are generated in primary metal production in the smelting of lead sulfide concentrates and in pyrometallurgical metal recycling systems. The compositions of these slags are varied due to increased fraction of recycled materials in the feed as well as introduction of previously unused chemical elements to modern technology. Therefore, their processing becomes chemically more complex; in that way they contain a large number of different metals. These slags form complex non-ideal solutions (with possible formation of several immiscible slags) that can coexist with stoichiometric solids, solid solutions, mattes and molten metal depending on the bulk composition and process conditions. Predicting the outcomes of smelting and refining processes is becoming increasingly difficult. To assist in the optimisation of these metallurgical processing operations, a comprehensive research program is underway to develop accurate thermodynamic databases for these non-ferrous process systems.

Jan 1, 2019

By J. Gonzales

For this paper, blending is conceived as a linear process that takes a proportion from one stockpile or location and mixes it with another proportion from another stockpile or location, with the aim of obtaining a set of attributes in the final combination that satisfies a given quality standard. A blending class is the combination of ore attributes and grade limits that should be stockpiled in order to achieve the target quality for the process Plant. Current literature considers the number of blending classes in the Open Pit Scheduling Problem as fixed; however, this paper shows how to define specific blending classes for a given deposit so that the schedule can be solved with Sequential Linear Programming. Finally, a practical application in a Peruvian copper mine is shown, involving four ore attributes: alteration code, arsenic, oxide content and copper grade. INTRODUCTION In copper ore deposits, blending for quality has not been a typical issue as it was for coal and iron ore; however, current copper deposits in the world are becoming geologically and chemically more complex than in the past and is not uncommon to have quality standards involving up to four attributes, introducing an additional complexity to the mine scheduling process [1]. In order to solve the Open Pit Scheduling Problem with multiple ore quality constraints, two assumptions are necessary [2]: - Grade constraints are defined only by specifying an upper and lower limit; - Ore attributes in stockpiles are pre-determined, i.e., the upper and/or lower grade limits defining each stockpile are already known at the time of setting the schedule. Assuming each ore attribute is classified as high, medium or low, and there are four attributes to be controlled in the target ore quality, the number of possible blending classes would be 3^4 = 81. This number is impractical to manage in Operations, and increases the complexity at the time of running the schedule; therefore, a more efficient way of classifying ore is required. Note that in practice, one blending class can be split into more than one stockpile location due to physical capacity constraints. Therefore, the number of stockpiles could even be more than 81. BLENDING CLASSES DETERMINATION For a given set of ore grades with lower and upper limits to be achieved, one has to find all feasible ore classes such that when blended, their grades will lie within those limits.

Jan 1, 2019

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By T. Braun

In 1911, a young mining engineer named Bartlett Thane assembled a large claim block, 4 miles southeast of Juneau, Alaska. Across the Gastineau Channel on Douglas Island, the Alaska Treadwell Gold Mining Company had, by 1904, produced gold valued at more than three times the purchase price of Alaska in 1867 (Kelly, 2010). Thane knew his deposit was lower grade than other mines or prospects in the area; however, if the deposit was developed on a large-scale, the trend and size of the deposit made the project potentially economic. In 1911, Thane developed a business plan for the project and successfully attracted investor interest. In 1912, Daniel C Jackling visited the property at the request of an east coast investment group. Upon inspection of 5 years of production records for the Perseverance Mine, Jackling saw an opportunity to apply the low-grade/high volume milling technology which was widely adopted to the copper porphyry deposits of the southwestern U.S. With a design capacity of 6,000 tons per day (5,454 tonnes/day), Jackling’s innovative mill design would require high volume underground mining methods and the power of two new hydroelectric projects. By 1915, the Alaska Gastineau Mining Company was in full production. Between 1915 and 1919, the mine and mill set production records for haulage and throughput. The hydroelectric projects proved to be successful engineering marvels. Operational difficulties related to ore grade, refractory elements and labor shortages interrupted production on an increasing basis. In 1921, the mining company permanently shut down operations. INTRODUCTION The Juneau Gold Belt begins at Windham Bay near the southern end of Stephens Passage and extends approximately 100 miles north to Berners Bay (Figure 1). The first large-scale and sustained underground mine, operated by the Alaska Treadwell Gold Mining Company in the late 1880’s, established the Juneau-Douglas area as the regional hub for transportation and development. In the mid-1890’s, the combined population of Juneau and Douglas reached approximately 3,000 residents, largely driven by employment and support demands of several small to mid-size underground gold mines in the region. By 1904, the value of the cumulative gold production of the Alaska Treadwell was five times greater than the purchase price of Alaska in 1867 (Kelly, 2010). By the turn of the 20th century, economic growth in the Juneau-Douglas area relied on supplies delivered from the lower 48. Passenger and freight shipping lines required 3 to 4 days to make the one-way trip from Seattle to Juneau. Established shipping routes required experienced crews due to navigation hazards and adverse weather conditions. Even with precautions at the time, steam ships and freighter vessels experienced breakdowns or encounters with natural hazards that resulted in damage or in some cases, sinking. Interestingly, with no roads or railroads connecting Juneau to other communities in southeast Alaska, Juneau still relies on seaborn shipping in the 21st century.

Jan 1, 2019