Search Documents

By A Rorke, B Cubitt, R Beeslaar

The recent drop in the value of the South African Rand has resulted in an increased export value for South African coal and has lead to new coal reserves becoming available for mining. Very often these reserves are in close proximity to existing structures and utilities thus calling for stringent blast control measures to keep the risk of vibration, air blast and fly rock damage to a minimum.

Jan 1, 1997

A mining joint venture presents a real management challenge to achieve harmony with the other participants in the successful development and operation of a mine. This can best be facilitated by a detailed agreement and guided by a set of joint venture principles which recognise the differences of the interests of the parties and seek to establish sound business and personal principles by which differences not anticipated in the agreement might be resolved. The major and minor co-venturers can and do present potential difficulties to one another. This paper, one of the pair in the joint venture panel discussion session, predominately presents the minor's viewpoint. Usually commercial matters such as project finance, areas of interest, divestment, pre-emptive rights and decision-making can be adequately covered in the agreement. However, when the parties disagree and have difficulty in resolving their differences, the joint venture principles should be used to advantage to resolve relationship difficulties.

Jan 1, 1997

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By D. P. Penswick

The Palabora open pit is scheduled to cease operations in 2002. While the ore body continues below the bottom of the final pit shell, the stripping ratio precludes further economic open pit mining. Palabora Mining Company has investigated various means of continuing copper production, and has determined that an underground mine is the best solution. Board approval to commence construction of the mine has been granted and shaft sinking is underway. First production is planned for the year 2000 and full production of 30 000 t/d will be achieved by the end of the year 2002. [ ] Mechanised block caving will be the mining method employed at Palabora. The cave will be initiated by excavating a thin horizontal slice known as the undercut. Removal of the undercut will induce stresses which cause the rockmass overhead to fracture. Fractured rock will gravitate through drawbells to drawpoints on the production level, and be loaded by LHDs for transport to crushers.

Jan 1, 1997

By G. A. Calboreanu

The deterioration rate of any metal or alloy is increased in a erosion-corrosion application because the passivated surface layer is removed by the solid particles contained in the pumping fluid and the material surface becomes corrosion active again. Numerous attempts were made to engineer a stainless steel with higher hardness and unaffected corrosion performance. Alloys of special interest in such an area are the duplex stainless steels particularly the CD4MCu material which has the capability of being hardened due to its ferrite-austenite microstructure. Unfortunately, the CD4MCu with higher hardness comprises different intermetallic compounds which will increase the corrosion rate. The paper is analyzing the erosion-corrosion performance of a new type CD4MCu with 32% higher hardness and superior wear performance. The corrosion performance of this new alloy is better than the corrosion performance of the common CD4MCu material which the industry could supply. The corrosion effectiveness was evaluated with the Huey test, the potentio-dynamic anodic polarization test and the weight loss test whereas the erosion resistance was established with a low stress ball-on-disk type apparatus. The Wilfley hard CD4MCu material had 39% lower weight loss and 32% smaller volume loss than the common CD4MCu alloy The hardness range of the centrifugal pump parts poured and processed with the Wilfley hard CD4MCu is 320-350 HBN versus 250-255 HBN hardness of the common CD4MCu. After approximately 18 months of experimentation and field testing it was clearly established that the life time of the Wilfley hard CD4MCu is higher than the common CD4MCu and consequently centrifugal pumps were supplied to different customers in North and South America. India and more recently Australia. Sincere thanks to all the A.R. Wlifley & Sons Inc. and Western Foundries Inc. employees who supported and help to implement this work. special thanks to George Wilfley. Dave Cobb. Bill Becker Sr. and Wayne Taylor

Jan 1, 1997

The Janet Annenberg Hooker Hall of Geology, Gems and Minerals, located in the National Museum of Natural History, Smithsonian Institution, in Washington DC, opened in September, nine years after initial fundraising efforts were begun. The 1,858-m2 (20,000-sq ft), $16-million hall was mostly funded by private groups and individuals, including $1.7 million from 43 National Mining Associa¬tion (NMA) member companies. Companies that contributed more than $100,000 included Cyprus Amax, Phelps Dodge, Asarco, Homestake Mining, BHP, Caterpillar, Cleveland Cliffs, Exxon Coal and Minerals, Freeport-McMoRan, Newmont Mining and Peabody Holdings. The mining industry's contributions funded a walk-through Mine Gallery. It. features diora¬mas of four mines, as well as numerous specimens associated with the mines. The Mine Gal¬lery demonstrates to the public the importance of mining. The hall was named in honor of Hooker. She contributed $5 million in cash plus the Hooker Yellow Starburst Diamonds to the project. The hall is touted by the Smithsonian as the "most comprehensive earth science complex of its kind." It consists of seven galleries, each devoted to different aspects of gems, minerals and rocks. In addition to the Mine Gal¬lery, the hall contains a collection of gemstones and jewelry pieces, an extensive collection of minerals, a gallery devoted to plate tectonics and a gallery devoted to the moon, meteorites and the solar system. The new hall is a complete makeover of the old and outdated Geology Hall. It was built in the 1960s and finally closed to the public in 1995.

Jan 1, 1997

By Brian S. Prosser, Ian J. Duckworth

With the trend in the coal mining industry pushing towards improved productivity and greater production, the number and size of longwall panels is increasing rapidly. The development and mining of large longwall panels causes unique problems in the provision of adequate ventilation at the working faces. Because of the transient nature of the longwall panel, and the difficult field conditions for ventilation measurements, detailed pressure and volume surveys are often not conducted around the longwall circuit. This is unforlunate because the highest resistance airway in longwall mines is typically the longwall tailgate, which frequently represents the only unregulated split in the ventilation network. This paper examines data collected from ventilation studies of longwall panels at nine mines. The variation in airway resistance, ventilating pressure and airflow is examined and compared with specific factors such as airway dimensions, ground conditions and support type used.

Jan 1, 1997

By Tan Zhenxiang

INTRODUCTION Koolyanobbing is an open cut iron ore mine, which is located in Yilgarn region of Western Australia. To prevent the operators from suffering silicosis diseases and protect the air from being polluted, a series of dust control measures have been taken. These measures include ventilation and dust control system for sample preparation shed, dust collecting system for drill rig, dust suppression system for ore processing plant, dust control for haul road. The details related to individual dust control measure are dealt as follows. SAMPLE PREPARATION SHED DUST CONTROL The sample preparation is one of the major dust sources at Koolyanobbing. The activity is being carried out at the sample preparation shed. It typically needs to go through the following stages, that is, crushing, splitting, drying and pulverising. The amount of dust generated from crushing and splitting is mainly determined by the moisture content contained in the pre- pared sample. A significant amount of dust is generated at the sample pulverising stage due to cleaning sample bowl with com- pressed air. To protect the sample preparing personnel's health and make the dust level in the air meet the requirement from the health and safety authority, a central ventilation and dust control system has been installed at the sample preparation shed. As shown in Fig. l, the system consists of suction heads, suction lines, dust collector and vacuum fan. The fan creates vacuum environment in the system, therefore the dust is drawn into the dust collector through the suction heads and suction lines. The dust collector is of fabric filter. When the dusty air comes to the filter, the dust in the air is collected and retained on the surface of the filter while the clean air passes through and enters the atmosphere. The retained dust is blowed out by the pressured air pulses and deposits into the dust bin underneath the filter. A time relay device is used to control the cleaning time and the cleaning interval. DRILL RIG DUST CONTROL A hydraulic percussion drill is used to drill blast holes. To carry out the drilling operation properly and efficiently, the cut- tings are being flushed out of the hole by the compressed air. In order to prevent from the fine particles in the cuttings escaping to the air, a dust collector is attached to the drill. The collector mainly consists of suction head, cyclone and bag filter. Refer to Fig. 2. The suction head is installed at the lower end of the feed beams and is movable. The moving range is up to 250 mm. It is not only used to restrict the cuttings, but also used to prevent water from entering the filters when drilling wet hole. A 406 mm diameter primary cyclone is used to separate the heaviest particles in the cuttings. It is also used as blast holes sampling equipment. One part of the dust particles are collected by a sample bag through a splitter attached to the end of the cy- clone. The rest of the particles fall down to the ground through the closing rubber. The bag filter is driven by a hydraulic motor (1). It is used to collect the lighter particles in the cuttings. The filtering area is 16 m2 and the dust separation efficiency is up to 99.9%. The working principle of the filter is demonstrated in Fig. 3. When the rock drill (9) flushing is turned on, the pressurised air from the compressor is directed to the rock drill and to the pres- sure switch (10). The pressured air will open the pressure switch to de-energise and close the solenoid valve (4) The pressure affecting the cut-off cylinder (5) keeps the exhaust port flap open. When the flushing valve (8) is closed, the pressure affecting the cut-off cylinder disappears and the internal intake opening flap is closed by a spring. The pressure also ceases to affect the pressure switch and the spring switches the contact to the point 2. The time relay (11) is now activated and gives a 0.5 second current impulse to the solenoid valve and keeps the current cut off for approx 8 seconds. When the solenoid valve is live, it opens and lets an impulse of pressured air to the filters (2). These impulses will clean the filters.

Jan 1, 1997

By R. White, C. Doyle, B. Martin, C. Díaz, J. Hrepic, G. Cuthbert

"A program initiated to improve the service life of the magnesite-chrome refractory in the top blown rotary converters at INCO’s Copper Cliff Nickel Refinery identified slag corrosion as a major wear mechanism. Target slag compositions were established to produce a non corrosive slag. A plant program to achieve this target slag by the addition of controlled amounts of do lime and MgO was instituted. Addition to rates of the slag modifiers was optimized based on the slag composition assays achieved and the requirement to address corrosion effects on the high alumina content ladle refractory. A60% gain in TBRC refractory performance was eventually achieved and has been maintained yielding a net annual savings of $700,000. A significant gain in available converter operating time has also been realized.IntroductionINCO’s Copper Cliff Nickel Refinery utilizes two top blown rotary converters (Fig. 1) to smelt a blend of semi-refined nickel concentrates, producing a granulated nickel matte suitable for the adjacent carbonyl based nickel refining operation. The converter, or TBRC, operation is a batch process composed of feed charging and melting, oxidation of the excess sulphur in the matte, and reduction of residual nickel oxide. The final matte, containing about 78% nickel, is tapped at 1600°C from the converter and is granulated in a sluice equipped with high pressure water jets."

Jan 1, 1997

By J Paul Tidman, Stephen H. Chung

One of the requirements in open pit gold mines is to minimise the mixing of ore and waste. Dilution can be reduced by choke blasting and control of the initiating sequencing. The authors have used the DMC computer model (developed at SANDIA) to examine the effects of timing and charge distribution on ore dilution. The model has been calibrated by measurements of vertical uplift derived from high speed videos made at the Dome Super Pit in Timmins.

Jan 1, 1997

By Chris Uys, Johan Labuschagne

Sishen Iron Ore Mine, located in the Northern Cape, is an open cast mine excavating approximately 100 million tons rock to produce 25 million tons of high grade haematite ore per annum. The size of the pit is approximately 12 km ‘1.5 km ‘150 metres. The final depth is planned to be around 350 metres. It is hard rock mining operation employing the conventional truck and shovel method. Mining benches are twelve and a half metres in height and are divided into blasting blocks, each consisting of approximately 300 000 tons of material.

Jan 1, 1997

By F. E. Wagner, L. J. Cabri, Y. G. Safonov, N. S. Bortnikov, A. D. Genkin, J. Friedl, G. N. Gamyanin

"A multidisciplinary investigation (including INAA, SIMS, EPMA, and Mossbauer Spectroscopy) was used to characterize gold in four of the largest Siberian mesothermal sulfide gold deposits. These are the Olympiada (""'750 metric tons gold) and Veduga (estimated at 75-100 metric tons gold) deposits in the Enisei Mountain Range and the Nezhdaninskoye (z500 metric tons gold) and Sentachan deposits in the Verchoyansk-Kolyma area. It was found that some of the mineralization is refractory in all four deposits, largely due to the occurrence of ""invisible"" gold in arsenopyrite as well as within pyrite, but with a lesser concentration. The gold concentration and its distribution varies considerably both within and between arsenopyrite grains, with implications for processing options such as heap leaching. The ore most likely to be amenable to heap leaching is the oxidized ore of the #4 orebody of the Olympiada deposit, but further quantitative mineralogical investigations are recommended for this orebody's sulfide ore and for the ores of the Nezhdaninskoye deposit. Following a full mineralogical characterization, it is possible that economic viability will depend on a combination of pre-concentration with or without pre-treatment, followed by heap leaching of some tailings products.Acknowledgements· The Russian authors performed this study under an ""Eco res"" Project which was financially supported by the Ministry of Science and New Technology of the Russian Federation. C.J. Stanley wishes to thank John Spratt and Terry Williams for help with EPMA. F.E. Wagner acknowledges the Deutsche Forschungsgemeinschaft for a grant supporting the Mossbauer studies. L.J. Cabri is grateful to the following: M. Beaulne, D. Carson and J.H.G. Laflamme for technical support, K.E. Haque for technical comments, and D.M. Hausen and W. Petruk for editorial suggestions."

Jan 1, 1997

By R. Togashi, T. Aichi, T. Yamada

"A new automatic material- handling system for cathode transportation has been developed. The first system went into service in August 1994 and the remains will be operational subsequently.Because of the complex cell-layout and the number of cells in each row, the critical part of this work was achieving a planned cycle time. This cycle time is determined by the power costs.The central monitoring system for machine operation was started in June 1996, using original application software based on MICROSOFT EXCEL ® on WINDOWS 95® .As a result, only one person is now required to operate both a crane and a stripping machine for one row of about 50 cells.INTRODUCTIONMainly due to the strong yen and the relatively low price of metal, the zinc refineries in Japan are being forced to reduce production costs again and again.The trend of lijima's production costs is shown in Figure 1.[1] The ratio of labor costs becomes gradually higher. Therefore it is effective to reduce the labor costs in order to reduce the production costs. In Japan, electricity cost during day time is too high to produce zinc at a reasonable cost, that is why the actual production is far from the capacity of production at a cell house. That means a plant in Japan has the disadvantage of relatively low productivity for cell house operation.Saving labor costsSome automatic cranes have been applied to save labor costs for cell house operation in the world. In consideration of the mentioned low productivity, the installation of an Automatic Cathode Transfer (ACn system for transportation of cathodes was planned without changing the present cell house and stripping machines to lower the investment costs. The ACT system must keep up with the stripping machine which is able to strip deposit zinc from a cathode sheet at the rate of 6 seconds.The fifth ACT system of seven was installed in August 1996 and the last one will be operational subsequently."

Jan 1, 1997

By Richard D. Begley

This paper will present the results of an analysis of several abandoned coal mine projects and includes field data for over a dozen different reclamation projects recently completed in the state of West . Virginia. The analysis was performed with the objective of summarizing and or classification of the environmental consequences with reference to the characteristics of the mining facilities (surface, underground, etc.). The analysis also addressed the itemized cost of remediation with respect to procedures, environmental concerns and time. The results of the analysis are that each abandoned coal mine site in West Virginia have/had many unique features and in most cases include a combination of environmental concerns that complicate comparisons. The study also revealed that the abandoned mine land program for mines abandoned prior to 1977 that is being financed by a tax on the production of coal, has produced many benefits for the state of West Virginia. This grant program administered by the Office of Surface Mining, has resulted in a high quality methodology of remediation that has been successful for many years in greatly minimizing and/or eliminating environmental concerns from abandoned coal mines.

Jan 1, 1997

By R. J. Sawyer

The Greens Creek underground polymetallic mine restarted production in 1996 from a newly discovered high grade ore zone. Efforts to improve payable gold recovery have focused on gravity separation. The paper compares testwork and plant results for a newly installed gravity circuit.

Jan 1, 1997

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By Dennis R. Barratt

Rockbolting is now used extensively as a method of primary support in UK coalmines. Over the past fifteen years an optimum bolting system has evolved, based on a high grade steel bolt and a very strong stiff resin. Where necessary, cablebolts are used in conjunction with rockbolts as a supplementary means of support. The rockbolting system, as currently used, is based on a maximum bolt length of 2.4 m whilst cablebolts are generally 6 or 8 m long. Based on the UK experience, there are situations where it is necessary to extend the bolted horizon above that normally achieved with a 2.4 m long rockbolt. Until recently the only options available were coupled rockbolts or cablebolts, both of which have inherent problems in terms of installation. Flexible Strand Rockbolts (FSR), in lengths of 4 to 6 m, provide the means of being able to extend the normal bolted horizon Other advantages include increased strength characteristics (tensile and shear), able to be installed in the UK standard hole size (26-28 mm), encapsulation using resin capsules, thus offering immediate support, high bond strength compared to conventional strand, and able to be installed using existing drilling and bolting equipment. The FSR is considered to be a new concept in terms of strata control and one that compliments the rockbolting system currently in use.

Jan 1, 1997

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC-formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30 individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed on to both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events. This is the first of two articles which report the responses that these experts gave when asked how they think people who may have to respond to a future mine emergency should be trained. During the interviews they discussed how training should be conducted, who should be trained, and what topics should be included. This article will cover the first two areas: what training methodologies would be most effective and who needs to participate.

Jan 1, 1997

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997