Search Documents

By W. J. Schlitt

Introduction A major uncertainty in assessing the potential for heap-and dump-leach projects is how to determine the extraction-rate curve for the recovery of the mineral values from coarse ore. Such material could either be run-of-mine (ROM) or primary crushed ore. The problem with field testing coarse ore, especially for new projects, is the large scale and extended leach times needed to accurately determine the final extraction-rate curve. At least 5 x 103 to 5 x 104 t of representative ROM ore are typically required for a copper test heap, and much more is often used. Kennecott, for example, recently constructed a 0.9 Mt (1 million st) ROM test heap at the Bingham Canyon Mine in Utah. In such coarse ore operations, the ultimate level of extraction will require a leach cycle that can extend from several months to a few years. Quite often, project development schedules do not provide the luxury of mining such large quantities of material or running such long tests. Instead, test data are usually limited to results from column leach studies on relatively fine ore, often with a top size that does not exceed 25 mm. Maximum leach times are also short, typically less than a year before an initial decision is needed on project viability. Proposed method One approach to estimating the recovery from a coarse ore leach is to assume that the leach solution will have some ultimate penetration distance into the rock. Then, the final level of mineral extraction in this "leached rim" will equal the ultimate level of extraction identified in various testing programs. Obviously, if the radius of a given rock fragment is less than the penetration distance, that fragment will be fully leached at the end of the operation. With larger rock sizes, the percent recovery will fall off as the size increases and the fraction of unpenetrated rock mass increases. Such an approach sounds simple but is likely to be complex when applied to a real project. For example, the penetration distance will be a function of both the rock characteristics and the effective length of the leach cycle. The important rock characteristics include rock porosity, the degree of internal fracturing and the mode of mineral occurrence. With regard to the latter, penetration is likely to be greater if the leachable mineralization occurs on fracture surfaces or in veinlets, as opposed to fine grains uniformly disseminated throughout the rock mass. An estimate of penetration distance may be derived from column or heap tests by noting the depth of solution penetration into the larger rock fragments after three, six and 12 months of leaching. While the penetration rate is ore specific, something on the order of 10 to 20 mm/y may be appropriate for competent, primary copper (chalcopyrite) ore. For gold in tight quartz, the rate may be about the same. Copper oxide ores and gold that is hosted in a more porous rock matrix are likely to have penetration rates that are at least two to three times higher, and an even higher rate should be appropriate for uranium hosted in sandstone. As noted above, the length of the effective leach cycle is likely to be measured in years. On this basis, the ultimate penetration distance (dp) would vary from less than 50 to several 100 mm when a particular ore is leached to exhaustion. Several sets of mathematical manipulations are necessary to convert a rock size distribution and corresponding value of dp into an estimated extraction-rate curve. The first step is to break the ROM size distribution down into intervals and then calculate the radius for the mean rock size in each interval. This is shown in Table 1 for rock sizes up to 1.75 m (about 6 ft) in diameter. The next step is to calculate the volume of unleached core and the fraction of rock that is leached. This is done for the following three values of dp: 25, 100 and 250 mm. Results are shown in Table 2. The third step is to select the ultimate level of recovery that will be achieved in the fraction of material that is effectively leached, i.e., the outer zone that is penetrated by the leach solution. This is clearly a site-specific factor that can only come from metallurgical test results on representative ore

Jan 1, 1998

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By Wang J, Ma Y, Jia H

The Hedong Gold Mine is located in the Yan(ai area, tihandong hroo%ill, e. China. It is an underground mine with an annual gold output of some 700 0(H) grams. The orebody is located on the edge of the Wanger Shan metamorphism zone, and the hangingwall of orebodies is thus defined by a prominent set of fractures. The proximity of the metamorphism zone and the inclusion of the fracture set ensure that both the orebody and the country rocks are unstable. The main orebodies dip at an angle of between 40 to 45¦, with a strike length of 160 metres and a horizontal width of 50 metres. Surface subsidence in the area is not permitted. Cut and fill mining is usually practiced. As the mining operation proceeds to greater depths, the ore grade is diminishing and it is necessary to find a more efficient stoping method. Sublevel open stoping with sequential extraction and filling of each sublevel has been designed and applied in situ. This new mining method is called 'sublevel open and fill stoping method' in the mine. Experience to-date is that new mining method is Satisfactory.

Jan 1, 1998

In February 1995, Falconbridge Limited approved the construction of a nickel mining and milling facility on its Raglan property situated in the Nunavik region of northern Quebec, Canada. The construction period successfully terminated with the commissioning and start-up of the plant and concentrator in early-December 1997. The estimated life of the project is 20 years with an annual mining rate of 800 000 tonnes of ore, producing 21 000 tonnes of nickel per year. This paper discusses the subject of æRemote Mining in the Canadian ArcticÆ as it applies to the Raglan mine process and people. During the feasibility stage of the project, many assumptions were made which influenced the design and operating parameters of the facilities and the equipment. Transportation, communication, remote logistics techniques and standard industry practices required to support a æfly-in/fly-outÆ operation were reviewed and either adopted or rejected for use at Raglan. These assumptions were æmade to fitÆ the uniqueness of our planned operation. It was also acknowledged that many of them would ultimately impact on the people required to staff the operation following construction. Therefore, their suitability and applicability were examined from an economic, operational and human perspective. In a continuing effort to improve the quality of life for Raglan employees, as well as the economics of our mine operations, these assumptions are under constant review and scrutiny. There is no doubt that experiences gained, and willingly shared by other North American arctic mining operations, proved invaluable and are a big reason for RaglanÆs overall success thus far. The mining industry is being challenged technically to develop lower grade orebodies at the lowest possible cost. In addition to environmental constraints, serious social, political and moral questions are being asked and added to this list of challenges. Miners throughout the world must improve their operating standards and public image if we want to attract the best possible employees. Remote mining operations provide a unique opportunity to experiment with various human resource concepts as well as demonstrate the industryÆs commitment to environmental and community concerns.

Jan 1, 1998

By T. E. Wilson

An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of? raw? coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which may not match the raw coal size distribution or size fraction composition. This study employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis in order to characterize the core material in terms of first-order and zeroth-order breakage rate constants. These are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling tests were done with synthetic cores, to reduce material variables and . conserve difficult-to-obtain coal cores.? Cores of three different coal beds --Illinois No.6, Upper Freeport, and Pocahontas No. 5 -were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining property) indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed than the crushed core.

Jan 1, 1998

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By John D. VandeKraats

Yielding rock bolt systems have been developed to provide ground support while accommodating shifting, creeping, or swelling ground movements. The Dywidag Systems, Inc. (DSI) Slip Nut System is one such system. It has been tested in the laboratory and installed and monitored in the interbedded halite and anhydrite at the Waste Isolation Pilot Plant (WIPP) since 1994. The Slip Nut System is installed on a point anchored threaded bar or on a threaded bar coupled to a cable bolt. At a pre-engineered load the nut acts as a die and cuts through the thread on which it rests, thereby reducing the load and coming to rest on the next thread where the process repeats. Two types of laboratory tests were performed using slip nuts on DSI's threaded bars and their Tensionable Cable bolts. Straight pull tests exceeding 0.3m (1 ft.) of displacement were performed on the systems. Also, offset tests were performed on these bolt systems in a test frame designed to simulate WIPP geologic conditions. A room scale test area consisting of 186 threaded bars began in 1994. Select bolts were instrumented to track bolt load. All bolts were tracked through time for operation. Through three complete years since installation over twelve slips, corresponding to approximately 0.15m (6 in.) of ground movement, have been observed in some areas. Since installation strata offset has exceeded 0.08m (3 in.) at a supported clay layer in the roof. No bolt failures have been observed. Slip loads observed underground generally approximate those observed in the lab. To date, the slip nut systems tested and installed have performed as expected.

Jan 1, 1998

By M Byrne, P Newman, M Lindqvist

SomincorÆs Neves Corvo Mine, one of the largest copper producers in Europe, is currently constructing a paste backfill plant in order to replace cemented rockfill in its bench and fill stopes and possibly replace hydraulic sandfill in the drift and fill stopes. A 250 m flow loop was constructed at the mine and the flow properties of various paste blends were investigated. Cycloned tailings and total tailings were both pumped successfully as pastes and were also combined with waste rock for additional testing. The pressure losses in 102 mm and 154 mm diameter pipeline were recorded at flowrates up to 60 m3/hr and are presented at slumps from 120 mm to 250 mm. The data showed the sensitivity of paste mixtures to slight changes in consistency, confirming the need for accurate control during paste production and distribution. The flow results clearly showed the different paste behaviour between cycloned and total tailings pastes and the change in properties at low and high slumps. In addition to pressure loss data, strength testing was done on 38 mm and 82 mm diameter samples. Further strength testing is ongoing at the mine using fly ash as a supplement to cement, reducing the overall binder cost. Preliminary engineering for the underground distribution system is briefly discussed, with reference to the siting of the plant. The Neves Corvo Mine is particularly shallow and alternative methods to pumping were sought in order to ensure sufficient hydraulic head for underground distribution. The comparison of options had to take into account the capital and operating costs, the operation of the plant and the impact on the future expansion of paste fill utilisation at Neves Corvo.

Jan 1, 1998

By S. Mafi

The Broken Aro project is associated with a 1910 abandoned underground mine complex that has been discharging aeid mine drainage from entries, seeps and springs. The Ohio Department of Natural Resources(ODNR), R&F Coal Company (R&F) and American Electric Power (AEP) are involved with this unique project that will remine the abandoned underground complex and install a mine seal constructed of fixated flue gas desulfurization (FGD) material. The goal of the project is to eliminate or reduce the acid mine drainage that is discharging into the watershed. This paper discusses remining, installation of the FGD mine seal, government financed reclamation projects and future application to active and abandoned mining sites.

Jan 1, 1998

New knowledge has no economic value unless it can be applied, or æcapturedÆ, as the R&D jargon has it. Australia probably spends more than $500 m per year on mineral industry R&D, distributed amongst the mining companies (IR&D Board, 1997), CSIRO, the universities and others. The investors in this research (industry, and the community via government) will expect some sort of return from their investment. The return will be poor unless the know-how developed in R&D programs can be exploited. This paper explores some of the issues involved in capturing the outcomes of mineral industry R&D in a form which can be exploited for economic benefit, and suggests ways in which it might be done better. It is based on the experience of the JKMRC in conducting applied research in mining and mineral processing and delivering it to the industry. It may seem presumptuous for a research contractor to be telling its clients how to do their job. However, the process of developing, acquiring and implementing R&D outcomes has to be a partnership between provider and receiver, in order for this process to work efficiently. This applies whether the two parties operate within a single corporation (a corporate laboratory and a business unit, for example) or are two entirely independent organisations (eg a mining company and a university). Both partners have a role to play, and the best examples of realising the benefits of R&D almost always involve the open-hearted and skilful handling of this synergy.

Jan 1, 1998

By M Maguire

The purpose of this paper is to provide an illustration of the Resource Management Act processes at their best. Many of you will be aware of the Martha Mine situated in the middle of Waihi Township in Hauraki District. Underground mining ceased on Martha Hill in the 1950s. A new mining licence was issued in the late 1980s and since that date open cast mining has continued at the site. The Hauraki District Council notified its proposed plan in October 1994. Prior to that date numerous discussion papers and draft sections of the plan had been disseminated in the community. Considerable consultation was undertaken with all interest groups. As an indication of the success of that consultation process only 17 references to the Environment Court were lodged following the making of decisions on submissions and further submissions. Those references, which included a number from the Minerals Industry, were all resolved by consent. Out of the reference and consent order process EMMA (Extended Martha Mineral Area) was born.

Jan 1, 1998

By S. C. Tadolini

The use of resin-grouted cable supports to control large ground movements in several types of underground mines has increased substantially since being introduced in 1991. Cables offer several advantages over traditional support systems, having large support capacities coupled with the flexibility to be used in low openings. Cable slings have been designed to be installed on-cycle using no-spin technology or a two-piece unit that can be placed with hand-held drilling equipment. Additionally, yielding cable supports have been developed and are being used to control large amounts of movement in coal and evaporite deposits.

Jan 1, 1998

By Robert R. Beebe

On the night of August 1'9-20, 1995, seepage was seen at the toe of the Omai tailings dam in Guyana. The mill was immediately shut down, and within two hours the flow, then mostly water, was diverted into an inactive mining pit nearby. At about the same time a second more serious break occurred at a point where water and solids could flow directly into the Omai River. By the time Ii coffer dam could be completed in the early morning of August 24, some 4.2 million cubic meters of tailings water and solids had escaped from the dam, of which nearly2.9 million cubic meters had reached the Omai River. This paper outlines some initial Process considerations and operational decisions which might have contributed to the dam's failure, describes how the Government of Guyana and the operator, Omai Gold Mines Limited, cooperated in dealing with immediate problems and shows how the Government set about investigating the accident. In particular, the paper details the work of a Process Review Committee comprising Guyanese and foreign experts convened to assess the gold processing and effluent management systems at Omai, and to recommend actions where appropriate.

Jan 1, 1998

By Neil McMillan

"By any measure of common practice, Claude Resources' Seabee Gold Mine in Northern Saskatchewan should not now be operating. Not because reserves dwindled, or grade dropped or prices weakened or technical problems arose, but because a host of unimaginable other problems beset the project, any one of which would normally have led to the mine's failure.The success of the Seabee Mine, and it is extremely successful, is a story of the vision and blunt determination of two men. Neither is remarkable in his own right but each possesses the characteristics which were necessary to forge a highly productive and profitable narrow-vein mine in the midst of the most bizarre and unpredictable events which likely have ever beset a mine start-up in Canadian history.Together, Bill MacNeill, a Saskatchewan born, former bush pilot and Ray Gagnon, a big hearted, hard-fisted, miner with 44 years of experience in Canada's underground, built the Seabee Mine.They didn't accomplish this with brilliant geology, outstanding engineering or nimble corporate manouvering but rather a stubbornness and raw common sense which likely are all too often, ingredients missing in failed projects.The Seabee Mine is 100% owned by Claude Resources, a Saskatoon based company taken over by Bill MacNeill, its current chairman, in 1982. The company is listed on the TSE and produces 1200 barrels of oil per day and about 60,000 oz of gold per year. The company has a strong balance sheet, is very profitable and has 18 million shares outstanding.The Seabee property in Northern Saskatchewan started out like many other gold exploration properties in Canada.It was discovered in the l 940's by what is now Cominco, and, while highly regarded by that company the property sat largely dormant until acquired by Claude Resources in 1985.Claude did what most junior exploration companies would do and went looking for a company with a depth of expertise to joint venture the property.That company was Placer Development who could earn a 55% interest in the Seabee by delivering a bankable feasibility study on the Project by July 1988 and providing financing to production.Placer Development was an excellent company and spent over $8 million dollars on the Seabee over a 3 year period. Unfortunately for Claude Resources, Placer Development merged with Dorne Mines in 1987 and the new merged company, Placer Dome, established a minimum production threshold greater than the 50,000 oz per year which the Seabee appeared capable of supporting at that time. Placer Dome's request for an indefinite extension of the joint venture agreement to allow it to drill off a larger ore body was rejected by Claude Resources and the Seabee Property was returned to Claude in 1988."

Jan 1, 1998

By H. J. Chen, Y. Luo, S. S. Peng

Surface subsidence resulting from underground coal mining can cause problems for buried pipelines. In this paper, a technique for assessing the level of stress on a subsidence-affected pipeline is introduced. The main contributors to the stress are identified, and mitigation techniques for reducing the stress are proposed. The proposed mitigation techniques were then successfully tested.

Jan 1, 1998

By J Robinson, D Herbert

Bench stoping operations at the Isa Lead mine have been underway for over 11 years. They were implemented to address safety, productivity and mining cost concerns noted with cut and fill mining operations which were then being used to extract ore from the Racecourse orebodies. This paper describes the main features of benching operations at the Isa Lead mine and identifies the key elements for the success of the method. Four case histories are presented which highlight several of these factors.

Jan 1, 1998

Mine reconciliation is the practice of comparing the tonnage and grade of material processed by the mill with the tonnage and grade of ore in the reserve model of a deposit, and with the tonnage and grade in the grade control models used to de

Jan 1, 1998

Teleoperation is one method by which an operator can remotely control and monitor a vehicle. The operator monitors the status and progress of the remote vehicle by watching the video transmitted from one or more cameras which are mounted on the vehicle. In the case of an LHD, it will be fitted with three cameras. For a twin-boom Jumbo, four cameras are mounted on the drill, three of which will have remote pan, tilt, 15x zoom, focus and lens cleaning controls. The advantage of teleoperation is that an operator can stand in the drive and send the remote vehicle around a corner, completely out of sight and still clearly see what is happening. This means that an LHD returns with a full bucket and a Jumbo can be operated from a safe distance. Standing in the drive teleoperating vehicles, exposes the operator to passing traffic including the remote vehicle. There are two solutions to this problem. One is to equip the operator with a Nautilus æBuddyÆ jacket which will help to protect them from all vehicles. The other is to move the operator into a safe room or area, away from the fumes, the noise and the traffic. In this comfortable, less stressful environment, the operator will be more productive and less likely to accidentally damage the vehicle. The operatorÆs æsafeÆ room does not have to be a formal control room, it can be any area which has AC or DC power available and is large enough to contain a chair and a 1.5 m x 0.75 m table. The æsafeÆ room can be on the surface or underground, it does not matter to the operation of the Nautilus Equipment. If the LHDÆs, trucks, locomotives, etc are automatically guided from origin to destination, the operator is free to operate several vehicles at a time, performing only those tasks which are too difficult for a computer to do by itself.

Jan 1, 1998

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998