Search Documents

By E. Contestabile, R. von Rosen, R. Guilbeault, R. Fouchard, P. Lightfoot

In August 1998, a truck loaded with 18 tons of blasting explosives, including over 13 tons of ANFO, left the road near Walden, Ontario. The crash caused a fire; approximately 30 minutes later a large detonation occurred, causing substantial damage to the roadway and local property. Although nobody was injured in the explosion, the consequences of a similar incident in a heavily populated area could have been catastrophic. Following the Walden incident, Transport Canada and Natural Resources Canada embarked on an extensive experimental program to determine the cause of the detonation. This paper describes part of that experimental program, designed to understand better the thermal decomposition of ANFO.

Jan 1, 2003

By Makoto Ohtsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SMB), The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force, The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films, The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a NisoMn2sGa25 or Nis2Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace, The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains, After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature, The martcnsitie transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated, After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found, The constraint-aged films also showed the two-way 5MB by thermal cycling,

Jan 1, 2003

"These guidelines, implemented in 2003, were recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. The guidelines are applicable to public companies and their consultants reporting diamond exploration results.“The guidelines are referenced in the Companion Policy of NI 43-101 with a statement that disclosure regarding the reporting of diamond exploration sampling results should conform to them.”Reporting GuidelinesThe following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results.In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results.Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results.The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is:Uniform within the diamond exploration industry; Consistent with reporting from other industry sectors .Comprehensive .Unambiguous .The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation.The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation)."

Jan 1, 2003

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By A. J. Basu

New technologies, such as computer based learning, wireless computing, internet2, online courses, distance learning, and in general multimedia applications are being implemented in the higher education sector in an increasing manner. However, these implementations are not coherent, and lack standards. However, one example of the existing standards is the development and implementation of the virtual learning environments. These technology tools help in delivering the eLearning objectives. There is a major initiative in Europe (eEurope action plan) in promoting eLearning towards creating a knowledge-based society. Technology implementation is the major driver for achieving the eLearning objectives. A two-year pilot project on implementing technology tools including virtual learning environment (VLE), video-conferencing, and simulation and visualization was carried out for providing a blended learning environment for undergraduate and graduate students in Mining Engineering (undergraduate) and Mineral Deposit Evaluation (M.Sc.) course at the Imperial College London. The pilot project was funded by the Imperial College Centre for Educational Development (ICCED). The project did contribute towards activities for creating an institute-wide eLearning strategy in line with the eEurope action plan.

Jan 1, 2003

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite,(Cu2S) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical equilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By F. -Z. Ji

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By P. Syrjänen, Lovén. P.

Because geostatistics together with block modeling has not been studied in detail before in the rock mechanics, a two-year research program to investigate the practical use of geotechnical modeling was started in Finland in 1999. According to research work results block modeling gives good estimate of overall rock mass quality but it can not identify individual structures like faults and narrow weakness zones. Weakness zones and faults should be mapped from drill cores, surface mapping, geophysical methods etc. and manually generate 3-D structural model. Rock mechanical 3-D modeling can be used for preliminary stope dimensioning and preliminary reinforcement design. Detailed design needs rock quality mapping from drifts during excavation work. La géostatistique associée à la modélisation par blocs n'ayant pas été étudiée en détail jusqu'à présent dans la mécanique des roches, un programme de recherche sur deux ans visant à examiner l'utilisation pratique de la modélisation géotechnique a été lancé en Finlande en 1999. D'après les résultats des travaux de recherche, la modélisation par blocs donne une bonne estimation de la qualité générale de la masse rocheuse mais elle ne permet pas d'identifier les structures individuelles comme les failles et les zones géologiquement dégradées étroites. Ces zones et failles devraient être cartographiées à partir de carottes de sondages, d'une cartographie de surface, de méthodes géophysiques, etc. et générer manuellement un modèle de structure 3D. La modélisation mécanique des roches en 3D peut être utilisée pour un dimensionnement de la chambre et un plan d'armature préliminaires. Un plan détaillé nécessite l'élaboration d'une cartographie de la qualité des roches des galeries lors des travaux d'excavation. Da man früher Geostatik und Block-Modellieren in der Gebirgsmechanik nicht detailliert untersuchte, wurde 1999 in Finnland ein zweijähriges Untersuchungsprogramm in Angriff genommen. Aufgrund der Untersuchungsergebnisse ergibt das Block-Modellieren eine gute Beurteilung der gesamten Gebirgsmassenqualität, kann jedoch einzelne Strukturen wie Verwerfungen und kleine Schwachzonen nicht identifizieren. Schwachzonen und Verwerfungen müssen demnach aus Bohrkernen, oder mit Hilfe von Oberflächenkartierung, geophysischen Verfahren usw. ermittelt und danach ein 3-D-Strukturmodell manuell erstellt werden. Felsmechanisches 3-D-Modellieren ist für die vorbereitende Abbaudimensionierung und für die vorbereitende Bewehrungsplanung verwendbar. Ein detaillierter Entwurf benötigt die Kartierung der Gesteinsqualität aus den Gesteinsstrecken während der Ausbrucharbeiten.

Jan 1, 2003

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By M. Barsky, A. Govorov, E. Barsky

A study was conducted to determine the structure and lifting capacity of a two-phase stream in a vertical pipe at different distances from the point of introduction of the material into the instrument. Stream velocity was set at 2.8, 4.0, 4.8, 5.6 and 6.25 m/sec to ensure separation regimes. It was found that the llifting capacity of the two-phase stream exceeded that of pure air by a factor of three or more, and that in a turbulent regime the velocity curve displayed marked deformation, becoming more rounded and tending towards a parabola. The following formula was obtained for entrainment of a given size fraction under turbulent, laminar and transitional particle flow regimes:

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Mineral froth flotation is one of the most widely used processes to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. The hydrophobic particles attach to the air bubbles and rise up to the froth phase on top of the slurry. The valuable mineral is collected when the froth overflows the cell wall. The separation performance of the process can be linked to the amount of solids and valuable material loaded on the bubble shells. In addition, it is well known that in most mineral systems, the presence of solids can enhance the stability of the froths. How the solids get to be distributed and what proportion is actually attached and stabilising the bubbles is not well known.This study aims to establish the relationship between operational variables, solids loading on bubbles and flotation performance. For this purpose, a series of industrial experiments to sample the solids in the bubble films under different operational conditions were carried out in two copper concentrators under steady state conditions. Samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. The amount of solids and liquid per unit area in the bubble lamellae can subsequently be estimated gravimetrically and by image analysis. The grade of the attached particles was also measured by adequate sampling. This gives an indication of the maximum grade that could be achieved from the process under the operating conditions."

Jan 1, 2003

By Lanre Oshinowo

The trend in process engineering is to design compact, more efficient processes, there is the paramount requirement to get the job done right the first time going from the drawing board to full-scale commercial operation. To accomplish this goal, there is also the need for tools beyond the traditional engineering toolkit to evaluate designs through virtual prototyping, thereby reducing the risks associated with making design decisions. One of the most important tools that has recently come to the forefront of process design and development is Computational Fluid Dynamics (CFD). CFD has been used at HATCH to address the key process parameters that drive the design of hydrometallurgical unit operations. This paper will detail the role of CFD at HATCH in achieving a superior level of confidence in the process design of autoclave circuits. Specifically, the optimum application of multiphase modeling including hydrodynamic, heat and mass transfer to hydrometallurgy operations, the impact of non-Newtonian slurry rheology on autoclave performance, and the challenges of optimizing the mixing of key reactants into slurries in autoclave reactors, is discussed.

Jan 1, 2003

By B Watson

The ConSep ACACIA Reactor is a device, which utilises a high intensity cyanidation process to achieve very high, usually near total, recovery of gold from gravity concentrates. The process utilises a fluidised bed and a chemical oxidant to enhance the gold dissolution kinetics to the point where the bulk of the dissolution occurs in a few hours. For convenience and security, most plants operate a 24-hour turn around. The product from the process is in the form of cathode gold ready for smelting by traditional means. The ConSep ACACIA Reactor performs a two-fold role. Firstly it increases gravity gold production, leading to a decreased CIP feed grade. Secondly, it removes slow leaching components from the plant leaching circuit. This two fold benefit leads to the following efficiencies: enhancement of the dissolution kinetics; enhancement of the adsorption kinetics; reduction of the gold load reporting to the carbon; a significant reduction of the ægold in circuitÆ lockup; and removal of slow leaching entities which can also result in a lowering of the required cyanide concentrations in the leaching circuit and a subsequent reduction in overall cyanide consumption. The above benefits are discussed in this paper, with a particular focus on the ConSep ACACIA ReactorÆs role in removing slow leaching components, with data generated over a 21-month period. Improvement in overall plant recovery via removal of slow leaching gold species is achieved in two ways. Firstly, some of the slow leaching entities, successfully leached under intensive cyanidation, are not always fully leached under plant conditions. This results in a lowering of the solid tailing. Secondly, the faster leaching kinetics achieved in the plant as a result of the removal of slow leaching entities results in faster and more complete adsorption of the dissolved gold onto activated carbon. This results in a lowering of the solution tailings. The construction and operation of the ConSep ACACIA Reactor is simple. Apart from the reactor body, which is a proprietary design, all components of the system are æoff the shelfÆ or specific to the siteÆs requirements. In operation of the fully automated version, a PLC controls a series of valves and pumps but except for a daily changeover process the only operating component for the bulk of the time is a relatively small solution pump. The process can be totally automated giving the security of a æhands freeÆ concentrate handling process up to the point where the product is presented as cathode gold. The ConSep ACACIA Reactor was developed by Anglogold Australia (formerly Acacia Resources) for Union ReefÆs Gold Plant and has been in production since February 1999. It has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, as of June 2003 there are eighteen full installations of the processing plant installed at mines owned and/or managed by Anglogold, Newmont, Placer Dome, Independence (formerly Lonrho), Sons of Gwalia and Harmony.

Jan 1, 2003

By Brian G. Thomas

Quality problems in continuous casting of steel can be identified as they occur by monitoring mold signals (level sensor, thermocouples in the mold walls, friction etc.) and taking appropriate action (such as slowing casting speed, changing taper, changing a clogged nozzle, or later visual inspection of the surface for possible downgrading. Surface depressions and groups of deep oscillation marks form at meniscus and reduce local heat transfer as they move down the mold at the casting speed. This slows shell growth, increases shell surface temperature, and causes characteristic dips in mold thermocouple signals. More importantly, they are also associated with longitudinal cracks. Characteristic thermocouple signatures have been identified for many defects, including sticker breakouts, transverse depressions and deep oscillation marks, narrow-face bleeds, transverse comer cracks, longitudinal cracks, mold level fluctuation defects, and other problems. With the help of computational models, these mold signals should be used to troubleshoot defects, and to take appropriate corrective action. Keywords: Continuous casting, defect detection, thermocouple signals, on-line control

Jan 1, 2003

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

By Choon Sunwoo, Chang-Ha Ryu

There are various methods available for the recovery of dimensional stone in open pit quarries. Explosive blasting has more advantages in the economic point of view over the other methods but was not widely used in Korea because owner was concerned about much economic loss when it failed. Several years of efforts have been made in order to develop more effective cutting methods and to spread to the quarries for strengthening the competitiveness in the market. Rock cutting by jet flame and black powder was generally used in the early stage. Black powder was applied to cut the last horizontal plane after forming other vertical planes using the jet flame. Jet flame operation, however, is time consuming and produces excessive noise, and as the result, brings adverse effects on the operator as well as the complaints from the residence adjacent to the quarry. Some mechanical methods such as the slot drill, diamond wire saw or in-situ scale of diamond saw cutting were introduced. Most effective cutting methods using the explosive blasting were developed and applied successfully. Black powder was replaced with the detonating cord. A new air decking technique where plug was not used was developed. This paper reviews the technology for dimensional stone cutting and case study in Korea.

Jan 1, 2003

By J Krahn

In designing climate exposed soil structures such as caps and covers over mine waste it is necessary to include the wetting and drying influences of the local climate in order to accurately predict the net water, vapour and oxygen fluxes across the ground surface and through the base of the covers. The most advanced evaporative flux modelling tools currently available to practitioners have been limited to rigorous one-dimensional models (ie SoilCover) or semi-empirical two-dimensional models (ie Hydrus-2D). It is common practice to use the rigorous one-dimensional evaporative flux model results to develop a surface boundary function that can then be applied within a saturated/unsaturated two-dimensional model. However, this is not an ideal situation and results in a further approximation of the real system being modelled. This paper will highlight the use of a new modelling tool, VADOSE/W, which brings existing, rigorously formulated evaporative flux theory into the familiar setting of a two-dimensional model. The model is enhanced for simultaneous two-dimensional oxygen gas transport analysis, which has direct application in the mine waste industry. A key focus of the paper will be addressing the limitations of one-dimensional analysis for cover systems on sloping and hummocky terrain.

Jan 1, 2003

By L Cooper, J Sharma, M J. Hendry

Thick clay tills below potash mine tailings and brine ponds are important natural barriers protecting fresh water aquifers in Saskatchewan. Centrifuge modelling was applied to assess geochemical processes and impacts of dilute brine (0.1 M NaCl) migration through clay till core samples obtained from non saline, unoxidised clay till at a mine site. At accelerated gravity of 876 + g, during each day of centrifuge modelling, flow driven through a 52 mm length core simulated transport through a 45 m thick clay over ~2100 years. Hydraulic conductivity, monitored continuously before and during brine permeation, was low and relatively constant (8.5 + 10-12 m/s), confirming that confining stresses prevent permeability increase. Core density and porosity measurements confirmed that reactive transport occurred under realistic in situ conditions. Breakthrough (defined by C/C0 = 0.5) of non-reactive Cl- occurred at 25 days. The slight delay for Na+ breakthrough, associated with small increases in Ca2+ and Mg2+ concentrations in the effluent were attributed to ion exchange, but carbonate reactions were relatively unimportant. Cation exchange analysis of core samples was inconclusive without corrections for porewater Na+ and carbonate dissolution. Geochemical processes that were observed during centrifuge modelling were successfully simulated using the 1D geochemical transport code PHREEQC. Solute transport was dominated by diffusion with limited ion exchange to delay Na+ migration. Brine would not break through a 45 m thick clay for tens of thousands of years. Based on these findings, the thick clay till at this site, if laterally extensive and undisturbed by drilling activity, is likely to act as an effective natural barrier to vertical brine migration over the long term.

Jan 1, 2003

By J Tuma

Technical measurements are an integral part of research and development of new technical devices. Now they are also an integral part of production too, especially as a part of quality control systems. More new problems started with they applications up, like storing and following preservation of big data files. Many problems are also with processing of the measurement results, especially to be up to standards of ISO 9000 normative. It includes basic data about the measurement (structured data) and measurement outputs (huge data streams). Using database systems looks as good idea, because of structured measurement data and they processing. They were developed more concepts of database measurement system support during the research project MSM 272300012. It was decided to develop specialised measurement systems, on the base of experiments and experiences with they use in operating conditions. It proved to be wrong to develop general system, because of compound operating and long response of the system. And it is not possible to use these systems for mass production systems. The problem of data storing is not as easy to be answered, because of dependence on used technical devices. During realisation the measurement system for gearbox noise measurement are data stored to the database, because used analyser system PULSE (Brnel and Kjµr Co) is open structure and can cooperate with other software systems. Anyhow the data streams are not longer (after compression) than the Memo data type, in practical use increases the data file too fast (about hundreds MB daily). Therefore we must include a special supervisory system for administration and creating data files to the system. Nevertheless the used system MS-Access supports data files up to 1 GB, for practical application is better if the file size do not exceed the capacity of CD-ROM disc.

Jan 1, 2003