Search Documents

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By K. P. Kavun, M. N. Denisov

Discussed in the paper is the redesigned reserve/resource classification for solid minerals being put forth by the authors to replace the acting Russian classification of 19961. The new version is based on the traditional foundations of former Russian classifications and the principles of the ‘McKelvey box’, both categorizing mineral resources according to the degree of geological assurance and economic viability. Based on these approaches the classification deliberately deals with both reserve and resource categories very similar to those established by the Geneva Accords in terms of definitions implied. The authors proceed from the UN-ECE proposed concept of ‘reserves’ being a part of ‘total resources’ explored in great detail by geological and feasibility studies and economically mineable at the time of reporting. The draft classification distinguishes ‘proved’, ‘probable’ and ‘possible’ categories of reserves depending on the stage of feasibility assessment carried out, i.e. the degree of detail and accuracy with which modifying factors affecting mineability of an orebody are taken into account. The reserves are regarded as a product of feasibility assessment of ‘measured’, ‘indicated’ and ‘inferred’ resources. The portions of them not having been classified as ‘reserves’ are regarded as composed of two classes: ‘subeconomic’ and ‘potentially economic’ resources (or ‘resource base’). All the cells of the classification matrix are provided with traditional for Russia alphanumeric designations and appropriate UNFC codes. The classification scheme recommended is viewed as a step forward in improvement of the State inventory and reporting mineral resources in market conditions, conducive to cross-border professional collaboration in the field of providing reliable information on the mineral rawmaterials base of the world’s economy. Besides, it recommends an easy way to get rid of amethodological error in the UNFC classification scheme where consecutive stages of geologicalexploration are identified with a single inherent degree of geological assurance. Keywords: mineral resources, mineral reserves, classification, geological assurance, feasibility studies, subeconomic resources, undiscovered resources, competent person.

Jan 1, 2003

By Liping Yu Che, Xiaotie Wang, Mingli Cao, Jizu Yongfu Yuan

"It is difficult separating fluorite from Ca, Ba, Si intergrowth minerals than simple from Si, using common reagents such as combination of oleic acid or paraffin soap and water glass, but the finest quality fluorite concentrate whose grade is over 96%F must be required in chemical plant.This paper studies the flotation process of native fluorite from calcite, barite and silicate minerals whose flotation properties is similar to fluorite, using new effective collector H602 and new depressor S602 that is cheaper in cost, and describes the flotation properties. In order to determine optimum flotation separation condition, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents on flotation were investigated and the flotation result was provided by oleic acid collector and the results of collector H602 were compared with those of collector oleic acid in the test. The test result of ore samples shows that at moderate pulp pH values (10.5-11.5) and other moderate technical conditions, the fluorite mineral can be obtained by new reagents and the rational reagents combination. The conclusion is 98%F of fluorite concentrate can be obtained, using the combination of H602 and S602 and only 5 steps in techniques. The paper discusses the mechanism of the flotation separation of fluorite mineral from intergrowth minerals."

Jan 1, 2003

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi?industrial scale experimental system, Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/em3J has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/em3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition or the car engine.

Jan 1, 2003

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, CSIRO Minerals, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented."

Jan 1, 2003

By Maurice Hunter

The paper outlines recent design developments in the computerization of surface crawler drills for the quarry industry. It references the technology firstly developed for the underground mining and construction industry, where automation and computerization has been in demand for a number of years.

Jan 1, 2003

By Nikolaos Polysos

Besides considering the given geomechanical conditions, the geological/geotechnical logging of drill cores and heading faces during the driving of parallel entries and the resulting rock classification form the basis of the assessment of the proneness to caving of the roof strata in the actual mining phase. Both types of separation planes, parallel to the stratification as well as intersecting the bedding, will be defined and assessed within the immediate roof strata depending on the lithological structure. These data may hold the potential to plan the winning and design its operational organization in a way that - to a major extent - future damage of the workings by increased caving or cavities can be predicted in advance. Following the general description of the separation plane structure, the combined influence of the petrographic and structural geological roof properties on the operating cycle of the planned working face will be presented and illustrated.

Jan 1, 2003

By T. Aoki, Y. Maeno, R. Kawano, F. Nakahara, Y. Obara, K. Shibata

The mechanical behaviors of fully-grouted long-embedded cablebolts actually used in situ are very non-linear in pull tests and are different from those of short-embedded cablebolts. We have conducted the pull tests of long-embedded cablebolts installed in mockup rock test blocks, which are 4m in the longitudinal length. In order to investigate the mechanical behaviors inside the test block, the axial load distribution along the cablebolt and locations of acoustic emission events were measured during each pull test. It was found that the axial force distributions were quite linear and that the gradients were interpreted as the grout bond strength by taking into consideration the stress balance at the infinitesimal segment of a cablebolt. Les boulons-câbles longs entièrement cimentés qui sont réellement utilisés sur place présentent, au cours des essais de traction, des comportements mécaniques considérablement non linéaires et différents de ceux des boulons-câbles courts. Nous avons mené des essais de traction des boulons-câbles longs installés dans une maquette de fond rocheux servant d’éprouvette d’une longueur longitudinale de 4 m. Afin d’étudier les comportements mécaniques intérieurs de l’éprouvette, la répartition de la force axiale du boulon-câble et l’émission acoustique ont été mesurées durant chaque essai de traction. Il s’est avéré que les répartitions de la force axiale sont sensiblement linéaires et que leurs gradients représentent la résistance d’adhésion en prenant en compte l’équilibre de contraintes à la partie infinitésimale d’un boulon-câble. Das mechanische Verhalten von ganz eingegossenen, lang eingebetteten Kabelbolzen, die vor Ort eingesetzt werden, ist bei Zugprüfungen sehr nichtlinear und anders als das von kurz eingebetteten Kabelbolzen. Es wurden Zugprüfungen mit lang eingebetteten Kabelbolzen durchgeführt, die in Prüfblöcken (Gesteinsattrappen) mit 4 m Länge eingelassen waren. Zur Untersuchung des mechanischen Verhaltens in den Prüfblöcken wurden die Axiallastverteilung entlang des Kabelbolzens sowie das Auftreten von Schallemission im Verlauf jeder Zugprüfung gemessen. Es ergab sich, dass die axiale Kraftverteilung recht linear ist, und die Gradienten wurden unter Berücksichtigung des Kräftegleichgewichts am infinitesimal kleinen Punkt eines Kabelbolzens als Haftfestigkeit interpretiert.

Jan 1, 2003

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By Mark Svinkin

The purpose of this paper is to present an overview of recommended existing criteria of ground vibrations generated by blasting. It is shown that these criteria have limited liability because they were found for specific categories of structures. A new approach based on measurement of structure vibrations is suggested for assessment of damage in structures subjected to blasting vibrations. This approach provides the flexibility of implicitly considering a variety of soil-structure interaction and structure conditions. It is explained a new frequency-independent safe-level criterion of 51 mm/s (2 in/s) for the PPV of structural vibrations. Attention is brought to use seismographs properly calibrated for the required frequency range. Positive flexibility is demonstrated in assessment of structure and component of concern vibrations from blasting.

Jan 1, 2003

"These guidelines set out information on timely disclosure of news releases which are intended to provide, existing shareholders and potential investors, factual information on which a reasoned investment decision can be made.Consider the problems and concerns raised by the following hypothetical news releases:Natural Resource Company""The Company has recently optioned a large and exciting gold property near the ""XXX"" gold discovery area. In describing the property, the Company's independent consultant has said: ""The favourable location of, and some of the results of prior work done on the property give the Company a worthwhile mineral exploration opportunity .... "". The Company proposes to expeditiously conduct a sizeable exploration program on the property as soon as the appropriate financing has been arranged.""Non-Resource Company""Based on discussions with several European countries, the Company anticipates that it will have orders to ship over 200,000 crates of widgets to those European countries over the next two years. These orders, which considerably exceed the Company's forecasts for the first year, represent a projected profit to the Company in excess of $1,000,000 over the next five year period.""GuidelinesTimely disclosure news releases are intended to provide, to both existing shareholders and potential investors, factual information on which a reasoned investment decision can be made. National Instrument 43-101 Standards of Disclosure for Mineral Projects provides requirements for disclosure of a scientific or technical nature for a mineral resource company.The examples do not provide sufficient detail and are misleading because material information is omitted. The following guidelines should be observed when preparing a news release:"

Jan 1, 2003

By A Creighton, C McKenzie

Blasting is a critical task in the development of an open pit. The formation of stable slopes is also essential to the safe and economic extraction of ore. The objectives of a mine blasting department are often considered to be in direct conflict with those of the geotechnical department. This should not be the case. Personnel in the various mining departments need to understand that their goals are the same û to optimise safety and cost-effectiveness of the operation. Blasting has the potential to damage rock that is to remain in situ by generating either excess vibration, and/or pressure. These damage mechanisms are described and guidelines with respect to blast design to minimise the potential for damage are given. A rock mass could be expected to be subjected to varying degrees of damage by blasting, including both intensity of damage and also the extent of damage. These issues have potential to impact significantly on geotechnical design considerations. It is therefore important for the practitioner to define what constitutes damage. In the context of mining, it is recognised that there is a need to balance the requirements for efficient excavation with those of forming stable and cost-effective pit walls. It is therefore important to have a set of key performance indicators (KPIs) against which the performance can be bench marked. These would include cost and time, both of which may be influenced by very diverse factors such as drilling, explosives and their performance, fragmentation, excavator and haul truck performance, requirements for batter clean-up and safe working practices. KPIs are identified and discussed in this paper.

Jan 1, 2003

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of composition at the temperatures from 850K to 1050K. An alloy was vacuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003

By R. Chryst, R. Kus

In the Integrated IT Systems proposed by Przedsie? biorstwo Robót Geologiczno-Wiertniczych—Geological and Drilling Company (PRGW) a network connects a database with all of the departments of a mining division. A key element thereof is the common graphics environment—Micro Station supplied by the firm, Bentley. PRGW’s SoftMine software and GMSI’s CadsMine that are used to design and schedule mining operate in this environment. The digital form of the design project facilitates the verification of information and the integration of technical solutions with SAP R/3 type financial—accounting systems. The system has been successfully implemented in the Brown Coal Mine in Poland.

Jan 1, 2003

By E. Laine

Rock density determinations are necessary for ore resource evaluations from estimated block grades in g/t. Rock density depends on the mineral composition and, thus, it is specific for each rock type. The rock density distributions for different rock types are often symmetric. Hence, the arithmetic mean is a good approximation for the average density for lithological units. However, there may exist spatial variation in density values due to alteration, fracturing and original heterogeneities such as layering. This study compares the kriged density model with the one with constant density values for different lithological units in the evaluation of metal amounts in rock blocks. The case study consisted of rock densities measured from the drill cores at Ahmavaara PGE deposit in northern Finland. The used Ni contents were simulated in accordance with the spatial distribution of rock densities. The Ni amounts in 2x2x2 m3blocks are higher for the kriged densities than for the average densities. The difference is increasing with the increasing metal amounts due to the nonlinear correlation between Ni content and rock density. The final effect on the resource estimation depends on the cutt off grade and prices of the metal, for example, for a very valuable metal the small differences are significant

Jan 1, 2003

"The technical report form provides the headings to be used and content required when a completing a technical report to be filed in accordance with NI 43-101. The technical report is meant to be a summary of the scientific and technical information on the mineral property. The Instrument (NI 43-101) requires that technical reports be filed with Canadian provincial or territorial securities regulators to support certain disclosure of mineral exploration, development and production activities and results in order to permit the public and analysts to have access to information that will assist them in making investment decisions and recommendations. FORM 43-101F1 TECHNICAL REPORT INSTRUCTIONS (1) The objective of the technical report is to provide a summary of scientific and technical information concerning mineral exploration, development and production activities on a mineral property that is material to an issuer.This Form sets out specific requirements for the preparation and contents of a technical report. (2) Terms used in this Form that are defined or interpreted in National Instrument 43-101 Standards of Disclosure for Mineral Projects (the “Instrument”) will bear that definition or interpretation. In addition, a general definitioninstrument has been adopted as National Instrument 14-101 Definitions that contains definitions of certain terms used in more than one national instrument. Readers of this Form should review both these national instruments for defined terms.(3) The qualified person preparing the technical report must use all of the headings of the items in this Formandmay create sub-headings. If unique or infrequently used technical terms are required, clear and concise explanations must be included. (4) No disclosure need be given in respect of inapplicable items and, unless otherwise required by this Form,negative answers to itemsmay be omitted. Disclosure included under one heading is not required to berepeated under another heading. (5) The technical report is not required to include the information required in Items 6 through 11 of this Form tothe extent that the required information has been previously filed in a technical report for the property being reported on, the previous technical report is referred to in the technical report and there has not been any material change in the information. (6) The technical report for development properties and production properties may summarize the information required in the items of this Form, except for Item 25, provided that the summary includes the materialinformation necessary to understand the project at its current stage of development or production. (7) The technical report may only contain disclaimers that are in accordancewith section 6.4 of the Instrument and Item 5 of this Form."

Jan 1, 2003

The relationship between neural network (NN) performance and the parameters that form the architecture of the neural network is complicated. This paper studies an issue that is still controversial—the effect of the number of neurons and number of hidden layers on NN performance. This paper tests if the above parameters affect network performance when the NN is trained according to the quick stop strategy. It was determined that the number of neurons did not have any effect on the NN performance for a single layer or a double layer network. It was also found that the training error and calibration error could be poor indicators of the prediction correlation coefficient.

Jan 1, 2003

By Steve Dillingham

The horrific events surrounding September 11th left Americans with a feeling of sudden helplessness...the shock of being unprepared and powerless. From this tragedy, we can understand the need to prepare for the unexpected, and can apply this hard lesson into operational planning for those involved in the commercical explosives industry.

Jan 1, 2003

By P. Goosen, A. Paterson, E. Paulsen

Ticor South Africa is currently involved in the mining and processing of a heavy mineral oredeposit at Hillendale Mine on the KwaZulu-Natal north coast. The orebody is characterized by a high ultra fine fraction (-45µm) that has a variable rheological behaviour when subjected to shear and hydration. Experience at Hillendale has shown that the ultra fine mineral tailings are sensitive to shear history in terms of shear intensity and shear duration as well as hydration history. This phenomenon expresses itself right through the primary beneficiation process influencing the mineral separation, but is especially prevalent on the residue disposal i.e. slurry transport and deposition on the tailings impoundment. Tube viscometer test work was conducted on the flocculated fine tailings that indicated that there was a change in rheology as a result of shear. This paper presents the results of the on-site test work conducted at the mine to measure the rheology at various stages in the process.

Jan 1, 2003

By Dean E. Harris

The realignment of U.S. Highway 95 in Sandpoint, Idaho, is being designed on a site underlain by glaciolacustrine soil that includes very thick deposits of soft, sensitive clay to estimated depths of greater than 200 m. The highway realignment will include construction of numerous embankments, mechanically stabilized earth (MSE) retaining walls, and pile-supported bridges. The area of the proposed new highway corridor also includes existing historic and commercial buildings, a railroad, sensitive environmental areas, and economically vital tourism/recreational assets. The evaluation of pile axial capacity included the use of a variety of methods, including total stress, effective stress, and empirical methods using the results of piezocone soundings and conventional borehole and laboratory tests. These methods were used along with the findings from an instrumented static loading test to design the piled foundations for the bridges. A critical factor throughout the design of the pile foundations was controlling settlements to levels that could be tolerated by the bridges. Also, because of the proximity of the pile foundations to the existing structures and the proposed new embankments, the project has required careful consideration of the potential interaction between these elements. The analysis of piles also considered the potential for settlement of embankments, drag loads on the piles, and downdrag.

Jan 1, 2003