Search Documents

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By M. Pawlik

The rheological properties of mineral suspensions affect the design and operation of transport, mixing, size classification, grinding, gravity concentration, flotation and de-watering systems. In many cases, the rheological properties can be modified to improve processing through the addition of chemical additives. These additives may be either organic or inorganic and generally affect the state of particle aggregation or dispersion. Inorganic modifiers act primarily by affecting the surface charge of mineral particles and thus control the magnitude of electrostatic attraction/repulsion between particles. The action of organic additives (polymers and surfactants) is a combination of electrostatic and steric forces – the latter being related to the molecular weight of these reagents. While low molecular weight polymers are dispersants (viscosity reducers), high molecular weight polymers are likely to induce flocculation and increase yield stress.

Jan 1, 2004

By N. Sutcliffe

Refractories and slags play a vital role in the production of stainless steel. They are in intimate contact with the steel at temperature, and chemical reactions between the three can and do occur. These interactions can be beneficial, in the case of active tundish and ladle slags, and negative in the case of refractory erosion and slag entrapment. This paper presents the results of both plant trials and laboratory investigations of steel/refractory and slag/refractory interactions. The interaction mechanisms observed are described leading to selection criteria for new refractory products. Keywords: slags, steels, refractories, reaction mechanisms.

Jan 1, 2004

By A. Patti, S. Reutzel, D. M. Herlach, L. Ratke, I. Egry

Cu-Co shows a metastable miscibility gap in the region of the undercooled melt. Undercooling of the melt below the binodal leads to separation of the melt into a Co-rich LI-phase and a Curich L2-phase. Experimentally, undercooling into the metastable miscibility gap is realised by means of electromagnetic levitation (EML), processing in drop tube (DT) and by melt flux embedding. As undercooling is large in these experiments, the velocity of the solidification front is high and the microstructure is frozen in instantaneously. Samples have been undercooled and solidified in the TEMPUS-facility (container less electromagnetic processing under weightlessness) during parabolic flight under reduced gravity conditions. Microstructures of solidified samples have been analysed and compared to those processed under gravitational conditions. The influence of convection on phase growth is much lower in reduced gravity. The microstructure shows spherical droplets of the minority phase, statistically dispersed in the majority phase.

Jan 1, 2004

By D Craw

The Macraes gold deposit is located in a low angle NE dipping (~15¦) shear zone, the Hyde Macraes Shear Zone (HMSZ) cutting greenschist facies metasediments of the Otago Schist. The shear zone is host to large volumes of mineralised schist and relatively sparse quartz veins. Early in the development of this through going shear the schist experienced an episode of hydro fracturing and fluid redistribution. As a result, presently exposed schists within the Intrashear sequence are pervaded by localised swarms of quartz filled pure extension and extensional shear fractures hosting goldscheelite mineralization. The swarms comprise networks or æstockworksÆ of veins that strike NE, are subvertical and form subperpendicular to the shear zone fabric. Vein frequency across strike is typically ~1 m-1, with most veins five to ten centimetres thick and vertically continuous for up to ~20 m. Many of the veins show delicately banded internal textures that are parallel to the vein margins. These bands/lamina indicate incremental growth and are defined by a variation in grain size or alternatively by thin slivers of wallrock schist, though typically uncommon. The majority of veins are overprinted by a weak plastic deformation, although primary structures are largely preserved. This deformation has produced subgrain structures, migration of grain boundaries with sutured margins and undulose extinction of grains. These microstructural observations possibly indicate that temperatures were around 300¦C during stockwork vein formation. In general, the mode of brittle failure that developed the stockwork veins can be directly related to lithological variation. The geometry of stockwork veins indicate that local vertical shortening and extension occurred in the Intrashear sequence of the HMSZ synkinematically with thrusting. Localised extension was mainly parallel to the structural trend; that is, it took place perpendicular to the direction of inferred thrusting. The development of lateral ramps most likely gave rise to extension in parts of the shear zone during continuous shortening to form swarms of stockwork veins.

Jan 1, 2004

By H. Preßlinger, H. Hiebler, K. Klepp, W. Posch, M. Mayr

It was investigated in which form sulphur is bonded in ladle slags. For this purpose, the mineralogical phases of the ladle slags were qualitatively and quantitatively evaluated by means of a microprobe. This slag characterization allowed reconstructing the bonding of sulphur into the phases of the ladle slag. Moreover, the reaction process with regard to the ionic theory as well as the structural formula for the mechanism of sulphur bonding were discussed. The bonding of sulphur into calcium aluminate slags is determined by the sulphide ion content in the slag as well as by the ratio of (CaO)/(Al2O3). Calcium sulphide separates only if the slag contains a large number of sulphide ions. When Ca12Al14O33is separated, the sulphide ion is successively integrated into the lattice. The crystal lattice of Ca12Al14O33is characterized by an open, three-dimensional anionic network composed of aluminium-oxygen tetrahedrons linking the edges. In this network, large interstitial spaces are formed, which may be filled with calcium ions on the one hand and statistically with a free oxygen or sulphide ion on the other hand. Key Words: ladle slag, structure, phases, calcium sulphide, calcium aluminate, desulphurization

Jan 1, 2004

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

By Tracie Zoeller, G. Paul Neitzel, Jr. Sanders

"As-cast aluminum alloy microstructures are highly segregated. Coring occurs when solute is rejected during solidification resulting in a non-uniform solute distribution across the dendrite arms. Furthermore, coarse constituent phases are formed in the interdendritic channels as a result of coring. These constituents are either soluble or insoluble and can form from the major solute elements, or the impurity elements iron and silicon. The dissolution of these constituents, or precipitates, is an important consideration in determining the microstructural evolution of an alloy. The properties of an alloy are significantly affected by the morphology of the precipitates. Precipitates can be either beneficial or detrimental to the properties of the alloy. Regardless of the nature of the precipitates present, it is useful to understand the dissolution process. A diffusion-limited dissolution model for planar precipitates is presented and compared to an analytical solution and to models in the literature. Experimental data for the dissolution of AhCu precipitates in a dilute alloy are compared to the proposed model, and found to have good agreement.IntroductionDuring the processing of precipitation hardening alloys, beginning with the solidification step and ending with the final solution heat treatment step, there are a variety of particles that form. Some of these particles must be dissolved and solute redistributed and re-precipitated in a more homogeneous distribution than as it first appears in the as-cast microstructure. The particles can be classified by size as microstructure develops during processing. Coarse particles that form during solidification can either be soluble, partially soluble or insoluble. These particles can be the result of coring of the major solute elements as well as the limited solubility of elements such as iron and silicon. Iron and silicon can combine with the major solute elements such as copper in 2xxx alloys forming coarse phases often referred to as constituents. Figure l(a) shows the as cast microstructure with the constituent phases, Al2Cu and the insoluble phases containing Al-Fe-Mn-Cu-Si [7]. During preheating the soluble phases such as AhCu that were formed by eutectic decomposition must be taken back into solution, whereas the insoluble phases remain essentially unchanged by most thermal operations. Figure l(b) and (c) show some of these constituents after subsequent preheating steps. In Figure l(b), AhCu platelets are shown and in Figure l(c) the remnants of the AhCu phase are noticeable, along with Mn-bearing dispersoid phases. Reduction in the volume fraction and size of these phases improves the ductility and fracture toughness as well as reducing the inhomogeneities that occur during coring. Also adjacent to the dendrite arm boundaries are smaller AhCu phases that precipitate by a solid-state transformation on cooling to room temperature."

Jan 1, 2004

By A. McKenzie

During the late 1990s Anglo American PLC was evaluating the Gamsberg zinc deposit in the Northern Cape Province. As the primary South African metallurgical technology provider, Mintek became involved in the evaluation of a pyrometallurgical process for the recovery of zinc from the Gamsberg deposit. eloping DC arc furnace technology for the metallurgical industry. This includes the patented Enviroplas® process for the treatment of zinc bearing waste materials. As a consequence Mintek has developed extensive expertise in the pyrometallurgical processing of zinc bearing materials. However, Mintek?s technologies stopped with the production of Prime Western Grade (PWG) zinc. Early on in the evaluation of the Gamsberg project, it became evident that the refining of PWG zinc would play an important part in the economic viability of the project. At the time the only pyrometallurgical technology available for the refining of PWG zinc to Special High Grade (SHG) zinc was the New Jersey process. This process represents 50-year-old technology and has not undergone significant refinement since the technology was developed. In order to provide a complete pyrometallurgical flow sheet for possible implementation at Gamsberg, Mintek assessed the New Jersey process with a view to either improving the technology or developing a new technology appropriate to the 21 century. In 1998 Mintek convened a consortium consisting of Mintek, the University of Cape Town, Eskom Enterprises, Bateman Metals and Anglo American PLC. The consortium successfully applied to the Innovation Fund for funding to develop a new process for the pyrometallurgical refining of PWG zinc to SHG zinc. The main aims of the project were to develop a new technology for pyrometallurgical zinc refining that conformed to the following: ?Decrease the production cost of SHG zinc metal to stimulate the development of the Gamsberg deposit. ?Be compatible with the current Enviroplas® process, preferably as an add-on to that process. ?Should use electrical energy to benefit from local price tariffs. The project commenced at the beginning of 2000 and consisted of three phases: ?an initial technology search and assessment of the fundamental aspects of zinc distillation. ?the design of a pilot plant for zinc refining. ?the manufacture, commissioning and operation of the pilot plant. A new technology based on a DC arc boiler feeding a packed distillation column was developed and during 2003 the project culminated in the successful operation of a 200 kg/h pilot plant. Ultimately, all of the aims of the project were met and the main outcome is that an advanced process for the pyrometallurgical refining of zinc (the Zincref process) has been developed. The main innovation of the technology was the switch from an energy transfer limited process to a mass transfer limited process (for which a patent has been registered).

Jan 1, 2004

The trend for using larger equipment in open pit mining to achieve cost effectiveness raises the question about the optimum economic point of scale in the current world of globalization. The present paper treats this question through the prism of a new methodology of assessing the impact of the size of production equipment on the economic outcomes of coal mining ventures. The methodology incorporates a production scheduling optimization model that implements both principles of mine planning, coal quality optimization and waste deferment. The implementation of the waste deferment principle dealing with the spatial and time aspects of the mine sequence arrangement allows the adequate modeling of the optimality of production equipment scale through the use of mine investment parameters, such as, purchase and ownership costs and discounted cash flows analysis. A case study is provided to illustrate the applicability of the new methodology.

Jan 1, 2004

By P. D. Tomlingson

Senior mining mangers that do not get directly involved in the quality of maintenance performance risk the profitability of their operations. Maintenance is not a stand-alone activity. It requires a production strategy that addresses the total life cycle of equipment from procurement to replacement and assures the fully cooperative, mutually supporting interaction of all mine departments. Only senior managers can assure this happens. This paper examines the strategies, policies and actions required to establish and sustain effective maintenance and the profitability that derives from it.

Jan 1, 2004

By Ashish D. Patel, Ramesh S. Minisandram

"Vacuum Arc Remelting (VAR) is the final and, hence, critical melting step for the production of a sound, segregation-free ingot for the manufacture of alloys used in rotating components in aircraft engines. A mathematical model for this process has been developed by the Specialty Metal Processing Consortium (SMPC). The model predicts temperature distribution in the solidifying ingot, flow in the molten metal pool, and the electromagnetic field in the ingot. These predictions may be used to estimate the effect of melting parameters on the pool profile in the ingot. In this paper, typical pool shapes and flow fields during VAR of Alloy 718 and Ti-6Al-4V are presented. The differences in the pool profile are primarily due to vastly different melting conditions. The model predictions are compared to the observed pool shapes from industrial-size VAR ingots.1. IntroductionVacuum Arc Remelting (VAR) is a process in which an electrode is melted in vacuum by the heat from a DC electric arc. Metal droplets from the electrode fall into the molten metal pool, which solidifies in a water-cooled copper crucible to form the ingot, as shown in Figure I. The ingot obtained from VAR is sound, and has superior cleanliness and chemical homogeneity. Hence, the process is the final melting process for most nickel-base superalloys and titanium alloys used in the manufacture of critical rotating components (discs & blades) of aircraft engines. Modeling of this process provides an insight into the effect of melting parameters on the molten metal pool in the solidifying ingot, which is a key first step in process optimization and defect prevention. In this paper, typical pool shapes, both measured and predicted, for VAR of Alloy 718 and Ti-6Al-4Vare presented. Alloy 718 is the most common VAR-processed nickel-base superalloy; whereas Ti-6Al-4V is the ''workhorse"" alloy for titanium-based alloys."

Jan 1, 2004

By Steven C. Borell

For more than a decade, changes have occurred each year that have improved the regulatory and business climate for mining in Alaska. These changes have taken place during Republican and Democratic governorships as well as when the state House of Representatives and Senate were controlled by either party. During some years, the changes have been relatively minor. In others, including the 2003 legislative session, the changes could only be characterized as massive. These improvements have encouraged exploration. This, in turn, has resulted in some major new discoveries. But Alaska is essentially unexplored and tremendous opportunities remain.

Jan 1, 2004

By John G. Reid

When the paper "Operations at the Greenvale Nickel Project Mine and Refinery" was delivered at the 1st International Laterite Symposium in February 1979, the Yabulu Caron plant had been operating for four years and production had just stabilized. The design had been based closely on the Caron plant at Nicaro, Cuba, built in 1944, also by Freeport. Yabulu had 10 Herreshoff ore roasters and production in 1978 was 18,682 tonne nickel as impure oxide sinter and 763 tonne cobalt in a mixed sulphide with a cobalt to nickel ratio of 1 :2.5. In the 25 years since the 1st Symposium, two more roasters have been added, but dry ore processing rate has remained relatively unchanged at 2.4M Uyr to allow a lower feed rate per roaster with associated higher recovery. The ore source has changed from the domestic Greenvale mine to imports from New Caledonia, Indonesia and the Philippines. Nickel production between 1978 and 2003 has risen by 67%, cobalt has risen by 146% and the products have changed to high purity nickel compacts and "ChemGrade" cobalt salt. The plant changes that have contributed to the increased recovery, production and product value are discussed. Keywords: Caron, Yabulu, nickel, cobalt, ammonia

Jan 1, 2004

By F. F. Peng, Y. Xia

In modeling of hindered-settling bed separators, the published separation mechanisms are based on differences of particle density and size distributions, without the details of complexity of particles-liquid interactions. A fluid dynamic model for the separator is developed using Euler-Lagrange approach of Computational Fluid Dynamics (CFD). Fluid motion is obtained from solving the movement of liquid governing equations. The damping effect on flow pat-terns caused by the movement of particles resulted in liquid-particle coupling is included in the model. Effects of particle size, and particle density compositions, feed rate, feed water flow rate, upward fluidizing water flow rate, etc., are simulated in the 2-D separation model. Flow pattern effects on the separation of fine particles in the separators with center downward-flow and side cross-flow feed systems are investigated.

Jan 1, 2004

By K L. Brown

In the Waiotapu geothermal area only Champagne Pool, 109 ng/L, and Waiotapu Geyser, 7.6 ng/L, have dissolved Au concentrations greater than 5 ng/L and most springs have concentrations less than 2 ng/L. When Au concentration data are combined with other physico-chemical data from each spring including; pH, reduced sulphur concentration and temperature, the degree of Au saturation can be calculated. All samples sites except Champagne Pool, Waiotapu Geyser and the Artists Palette are under-saturated with respect to Au(s) by 1 to 3 orders of magnitude. This indicates that adsorption or co-precipitation or both are important processes depositing Au beneath hot springs. Deposition of Au by adsorption or co-precipitation beneath hot springs implies that dissolved Au may not have to reach saturation concentrations for ore to deposit. This interpretation is supported by the presence of substantial Au as sub-microscopic components within sulphide minerals in ore deposits and indicates depositional efficiency beyond that possible through precipitation of Au(s).

Jan 1, 2004

By F. T. Cawood

Inauguration of the new political dispensation in South Africa in1994 initiated a dynamic shift in the ownership, management and development of the country?s affluent mineral heritage. The process of substituting the old South African regime with a new equitable system started soon after the 1994 election of the African National Congress (ANC) to parliament. The Congress?s Freedom Charter revealed the intent of the new dispensation when it called for radical transformation of mineral development. However, since then there have been important changes affecting the rules of mineral development. These are: ?A drastic change in politics ushered in by negotiation, a spirit of reconciliation and a desire to settle disputes peacefully ?The globalization of the South African mining industry in tandem with the opening of domestic mineral resources to foreign capitalists and ?The introduction of sustainable development as a holistic approach to mineral development in order to replace traditional narrow-minded environmental management. Each of these significantly shaped the new mineral investment environment of South Africa. This paper represents a summary of the historical developments leading to the current Mineral and Petroleum Resources Development Act No. 28 of 2002, its regulations, the much publicised Broad-Based Socio-Economic Empowerment Charter, its associated Scorecard, and the Draft Royalty Bill.

Jan 1, 2004

The paper deals with the importance of design and of codes of practice in ensuring safe working conditions in mines. The design principles involved in the design process are dealt with, and the importance of a logical design process is emphasized. The links between the requirements for developing a code of practice, embodied in the existing guidelines for the preparation of such a code, and the design principles and process are considered in some detail. Finally, suggestions are included, which may provide improvements to the code and hence, ultimately, lead to further improvement in safe working conditions.

Jan 1, 2004

By K Osten, N Scagliotta, G Lane

Oceana Gold (New Zealand) Limited operates the Macraes Gold Mine near Dunedin on the South Island of New Zealand. The orebody is mineralogically complex and comparatively low grade requiring a series of unit processes and resulting in a relatively complex plant. As part of Oceana GoldÆs ongoing Business Improvement program, a concerted effort has been made to focus on operational efficiency. One aspect of this has been the efficient use of energy in the gold recovery process. A benchmarking process has been developed for the Macraes operation that includes comparison with other operating mines and theoretical design. Criteria for determining operational efficiency have been developed. While benchmarking is, in theory, a simple process, this paper looks at putting benchmarking into practice by catering for variability in ore and associate processing methods. The unit processes discussed include the comminution circuit, flotation plant, pressure oxidation plant and gold recovery circuits.

Jan 1, 2004

By S. Afshar, C. Allaire

Several studied have recently shown that the use of non-wetting additives is not always a sufficient solution to improve the corrosion resistance of refractories against molten aluminum. Once in contact with liquid aluminum, the coarse aluminosilicate aggregates, which do not benefit from the protective effect of non-wetting additives in the matrix, may be corroded. In some cases, the corrosion of aggregates, especially those containing a significant amount of free silica and/or alkalis, promotes corrosion in the surrounding matrix. The present work explores the possibility to protect the poor corrosion resistant aggregates via a lining procedure. A slip casting method, using either alumina or celsian-like composition based slurries, has been applied for lining of a series of aggregates. The results from this study show that such linings may prevent efficiently the corrosion of aluminosilicate aggregates. This work also analyzes the effects of firing temperature and lining quality on the corrosion behavior of aggregates

Jan 1, 2004