Search Documents

After the closure of collieries, they naturally start to fill up with water. As a result, hydraulic gradients develop between them and different hydraulic pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The collieries in the Witbank Coalfield have geometries such that there are several areas where this intermine flow is possible. Since the Department of Water Affairs and Forestry has declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon is required. The challenges in determining intermine flow are numerous, and attention has focused on identification of areas where these flows can take place. The quantification of these flows is problematic due to the uncertainties in exact geometric configurations and the variation in site-specific hydraulic properties of thecoal and overlying lithilogical layers. During this study, use has been made of numerical flow modelling and several analytic solutions to test the applicability of the flow models as well as to predict groundwater flow directions, filling times of voids and flow volumes. The numerical modelling methodology entailed a downscaling approach starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines, and finally looking in detail at the major areas of interaction.

Jan 1, 2005

Drum winders have now been built to attain depths of 3000 m and more in a single lift in accordance with the South African Code of Practice SABS 0294, which was introduced at the time of the last hoisting conference in 2000. Since then, this code has not only been followed for several winders in South Africa but was also followed in deep mines in Canada. Design of winders and their braking systems are described in the paper. Koepe winders are in use for high payloads of up to 50 t and to hoisting depths of around 2100 m. As known, the stress range of the hoisting ropes is the key parameter for rope fatigue. However, as per the SABS Code of Practice 0294, relying on static design is not the answer to the question of where the limits are for Koepe installation. The paper describes factors that are recognised to have influence in rope life and suggests definition of new design criteria for friction winders in order to get viable solutions for high-capacity hoisting from deep mines similar to drum hoisting.

Jan 1, 2005

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

By P. Fauvel, V. Nasri

In January 2001, French and Italian governments signed an agreement for the construction of a new Lyon-Turin railway line. This project includes a tunnel of 53.1 km length and a maximum of 2500 m overburden to be designed for a reference speed of220 km/h. The tunnel crosses major part of the West Alpine geological formations, which are very complex and contrasted in terms of the nature of rocks and the mechanical and hydrogeological conditions. In addition to the twin single-track tubes, numerous intermediary shafts, security station and intervention sites and cross passages should be built to respond to the security, operational and construction requirements. This paper describes the results of the preliminary engineering design and multiple challenges of this very long and deep railway tunnel.

Jan 1, 2005

By Denise de La Corte Bacci

The Brazilian Regulation NBR 9653 is a guide intended to evaluate mine and quarry blasting effects in urban areas. The first version, written in 1986 by the Committee of the Brazilian Associate of Technical Norms, is currently being revised. Current regulations specify a maximum PPV limit of 15 mm/s (0.59 in/s) without consideration of frequency or type of structures being protected. The present regulation is still a draft and it is not validated. Several different agencies and institutions have participated in the Committee such as the Environmental Agency from the State of São Paulo (CETESB), University of São Paulo (POLI-USP), University of Rio Grande do Sul (UFRGS), National Department of Mineral Resources (DNPM), Aggregate Industry (ANEPAC and SINDIPEDRAS), besides a number of industry representatives, explosives manufactures and independent consultants. The present regulation proposes to modify the limits of particle velocity and introduces new definitions and criteria for evaluation of vibrations, as well recommendations to address blast vibration complaints.

Jan 1, 2005

By Antoine F. Mulaba

Introduction Copper and cobalt oxide mineral deposits formed by the atmospheric weathering of near surface sulphide deposits are commonplace in the Democratic Republic of Congo. The most common route for the extraction of these metals is a hydrometallurgical one in which the base metal oxides are dissolved in sulphuric acid and then concentrated further by solvent extraction. However, as many of these deposits are relatively low grade (i.e. 0.5-1.8%Co and 2-4% Cu) and can also contain large amounts of acid consuming gangue minerals (i.e. dolomitic, micaeous, and/or siliceous), the hydrometallurgical route becomes uneconomic due to the excessive acid leaching costs. Some means of pre-concentration ahead of leaching is then desirable to improve the process economics. Apart from the small scale mining (Pan. Afr. News Agency, 2000) handpicking, although not easy, oxide concentration by flotation has been suggested. For the flotation process, the two most common approaches are controlled potential sulphidisation (CPS) and the fatty acid flotation method. The preferred method is dictated by the nature of the mineral makeup of the gangue. Being secondary deposits, the gangue associated with these ores is often complex and can play a significant role in the overall flotation efficiency. Laboratory flotation experience gained from the testing of a number of different ores of this type has revealed that it is not possible to prescribe a set method for the flotation of various ore types. Each ore needs to be analysed very carefully before and after laboratory flotation on an individual basis in order to arrive at an acceptable flotation technique Laboratory flotation testwork was carried out on three different samples from the DRC in attempts to isolate some of the more important variables affecting the flotation of copper and cobalt oxide minerals from these weathered deposits. This paper describes some early results achieved and experiences gained with these different ores ahead of a more detailed flotation test program which will follow in the near future on receipt of a significant quantity of a more representative sample. Controlled Potential Sulphidisation (CPS) was used in an attempt to achieve acceptable recoveries of both copper and cobalt.

Jan 1, 2005

By Troy Holm, Matthew L. Fuller, Frederick H. Earnest

Virtual Reality Animation Of The Proposed El Dorado Mine In El Salvador Assists Regulators In Reviewing An EIA

Jan 1, 2005

By J J. Wilkinson, C J. Ha, R J. Herrington

The Pic de Fon iron oxide deposit is a potential major new source of iron ore, located at the southern end of the Simandou range in eastern Guinea on the West African Craton. The deposit is hosted by banded iron formations (BIFs) within a supracrustal sequence, which lies unconformably upon a crystalline basement. The host BIFs and shales have been metamorphosed up to staurolite-grade itabirite and phyllite respectively. Stratigraphic relationships are obscured by polyphase deformation, although the sequence appears to comprise a lower phyllite(-minor quartzite) unit and transitional phyllite-iron formation overlain by three itabirite units. It is the itabirite units, selectively enriched to iron grades in excess of 65 per cent Fe (with low deleterious elements), that constitute the Pic de Fon deposit. Samples acquired from exploration diamond drill holes and outcrop across the deposit have been collected to investigate the Pic de Fon lithologies and iron-rich material types. Initial research techniques have included geological mapping, reflected light microscopy, x-ray diffraction (XRD) studies and ICP-AES geochemistry. The aim is to develop a model for deposit genesis that may assist future exploration and deposit exploitation planning. Results to date have identified a variety of hematite textures, which include recrystallised trellis, interlobate and granoblastic hematite after magnetite. In addition, fine-grained bladed to acicular microplaty hematite appears to both replace itabirite banding and infill porosity. Field relationships indicate a structural control of microplaty hematite development. Geochemistry and XRD results suggest a loss of silica with negligible iron addition during the conversion of itabirite to ore grade mineralisation. The enrichment process(es) is also accompanied by a gradual increase in K, Mg, Na, (Ca and Al).

Jan 1, 2005

By John P. Dunford, Lewis A. Martin

Researchers from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, in cooperation with engineers from the Department of Mining and Geological Engineering, Montana Tech, Butte, MT, conducted tests to evaluate the tensile strength, fiber count, and adhesion of shotcrete applied to panels at the Chief Joseph Mine, a research and training facility operated by Montana Tech. The tests were conducted in the mine ramp 45 m (150 ft) inward from the access portal at a 15.25-m- (50-ft) long test area divided into five 3-m- (10-ft) long sections. The shotcrete was applied with an Aliva 240.5 machine fitted with a predampener. Different amounts of fiber were entrained for each panel. Background data for the tests were obtained from earlier tests in Nevada, where the typical amount of fiber in the shotcrete is 6.54 kg/m3 (11 lb/yd3). All shotcrete was applied to a minimum thickness of 76 mm (3 in). Cylindrical cores were drilled at the wall-rock interface, and adhesion was tested after 28 days of curing. The goal of this research is to reduce the need to install multiple supports at the advancing face by creating a safer mining system that limits the time miners are exposed to unprotected roof.

Jan 1, 2005

By V Malysiak, N J. Shackleton

In the flotation of platinum group minerals pyroxene is a major gangue mineral. This study shows using zeta potential and ToF-SIMS analyses that when pyroxene is exposed to copper, nickel and/or calcium ions in solution at alkaline pHs a surface reaction occurs between the hydroxy species, in the case of copper and nickel, or divalent calcium ions and the pyroxene surface which influences the floatability of the pyroxene. Following exposure to copper and nickel ions at pH 9 addition of SIBX resulted in the pyroxene floating readily. It is also shown, in the case of copper, that the activating effect of the adsorbed copper hydroxy species can be reduced by the addition of complexing amines prior to SIBX. Proposals are made to explain these observations.

Jan 1, 2005

By Ryan Lindmark, Guoxing Gu, Zhenghe Xu, Jacob H. Masllyah

Induction time is often referred to the time required to form a stable three-phase contact between a gas bubble and a flat or droplet surface in a liquid medium. It can be used to quantify the attachment process in aflotation system. Various techniques have been developed to measure this important parameter. Due to its importance in flotation systems and other processes, significant advances in refining the induction time measurement techniques have recently been made. This paper summarizes these recent advances and describes a novel method developed to monitor bubble attachment to a pendant bitumen drop or bitumen-coated flat surface. This visualization-based method offers a higher sensitivity and accuracy than the previously developed apparatuses in the induction time measurement. As an example, the induction time for oxygen bubble-bitumen attachment was measured at a fixed bubble size as a function of temperature in two different aqueous solutions. The results showed that higher process temperature is favorable for oxygen bubble-bitumen attachment and hence bitumen flotation. Addition of calcium to the aqueous solution slightly decreased induction time.

Jan 1, 2005

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

By Andrukaitis. E.

The increasing use of electronic equipment by the Canadian Forces has increased the importance of electric power. A power source that is packed with energy and yet light, small and durable is the common request of military users. However, this needs to be achieved while also addressing the requirements of safety, reliability and low temperature performance. The potential use of fuel cells in a military environment has become a possibility in several areas in the 21st century. Some examples of power source requirements and the materials related R&D required to give better, higher energy power systems in the future will be discussed.

Jan 1, 2005

By Yuemin Zhao, Daniel Tao, Xinxi Zhang, Qingru Chen, Maoming Fan, Zhenfu Luo, Xiuxiang Tao, Guohua Yang

Coal is currently cleaned with the minimum of size reduction, fine particle processing, recovery, and tailings disposal are major problems. Adequate water resources are not always available. For example, two thirds of China's coal is located in arid areas. Hence, dry separation provides an alternative approach. Of the dry coal separation methods available, air dense-medium fluidized beds have been used to separate 50~6mm coal efficiently. However, excessive bubbling and back mixing of the separated solids in the air-dense media fluidized bed causes the high lower size limit of 6mm for the feed material, this affecting the preparation efficiency. Based on prior study on air-fluidized dense media for 6~50mm coal preparation, this paper presents methods and test results on the fine coal dry classification, static electricity beneficiation of 0~0.5mm coal, and magnetically stabilized fluidized beds for separating 0.5~6mm coal.

Jan 1, 2005

By P Gunn, M Watts

The general goal of passive acid mine drainage (AMD) treatment is to reduce levels of acidity and metals to acceptable levels. Most treatment systems use either an oxidising or a reducing strategy. In oxidising systems, alkalinity is added along with dissolved oxygen; in reducing systems, dissolved oxygen is removed (if present) and then alkalinity is added. It is recommended that small-scale field trials be conducted as part of the methodology of selecting the best remediation strategy at AMD sites. Following successful field trials at the Sullivan Mine AMD, the Pike River Coal Company (PRCC) has shown foresight by using the same system to treat AMD generated as a result of taking a bulk sample of coal at the Pike River coal field. The system reduced acidity by 100 per cent, iron by 99 per cent, aluminium by 96 per cent, nickel by 95 per cent, manganese by 51 per cent and zinc by 99 per cent. The success of this field trial suggests that a system using a reducing strategy may be appropriate for the Pike River Adit AMD site.

Jan 1, 2005

By Z. Zhang

Aluminum boron carbide particulate reinforced composites have found new applications in nuclear industry due to their special capability to capture neutrons, Recently, Alcan successfully developed a liquid metal mixing process to fabricate Al¬B4C metal matrix composite instead of powder metallurgical technology. In the process, titanium is added into the composites to control interactions between boron carbide particulates and aluminum matrix, To understand the effects of titanium on the composites, the solidification microstructure of Al-16%B4C without or with titanium was examined by optical and electron microscopes. The results show that titanium can improve the uniformity of the particulate distribution within aluminum matrix if the titanium content in the composites is more than 0,5%, Furthermore, it is found that the layer with rich titanium on the surface of the particulates can limit the formation of AlB2 type compounds, which may greatly deteriorate the fluidity of the composites, In addition, it is also found that the amount of the reaction products in the composites increases with the increase of holding time. However, the rate of the increase is mitigated by the increase of the content of titanium in the composites. Besides, a procedure was proposed and implemented for the evaluation of uniformity of particulate distribution within aluminum matrix.

Jan 1, 2005

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By A. Lam

The use of a liquid fed direct methanol fuel cell (DMFC) as a power source for micro and small portable applications is attractive due to its system simplicity, low temperature, etc. The aqueous methanol is directly oxidized and does not require additional fuel processing steps as in reformate based PEM fuel cells. In addition, the use of a liquid fuel is advantageous with respect to humidification, stack cooling and system energy density. The DMFC however, has technological issues that must be addressed before it can be widely adopted, particularly in larger applications such as small utility and transportation. At present, the crossover of methanol from the anode to the cathode is a major limitation on DMFC performance and fuel utilization efficiency. In this paper we discuss the influence of fuel modification on the control of crossover. This involves the use of different fuel additives and concentrations to minimize crossover. This appears to be the first reported case of the use of fuel modification (additives) to reduce methanol crossover. The rate of methanol permeation under passive conditions is discussed with respect to the different conditions.

Jan 1, 2005

By C. Stoneback

The attapulgite industry saw a year of solid growth after a weaker 2003. Demand was up between 5 percent and 6 percent driven by almost all of the key markets. Construction continued to show record new housing demand, assisted by continued low interest rates. That drove strong growth in construction related markets like coatings, tape joint compounds and other construction materials applications. The agricultural markets rebounded modestly to increase sales for suspension fertilizers, animal feeds and pesticide carriers. Oil drilling also showed strong growth due to high oil and gas prices. Sales to molecular sieve applications grew due to petrochemical and construction demand. The export markets were assisted by further depreciation of the dollar. The only weak area was in nonagricultural granular sorbents, where other sorbent materials continued to dominate.

Jan 1, 2005

Two characteristics of the modern mining industry are that there is a skill shortage and that young professional people rise rapidly into highly responsible supervisory positions. With this responsibility comes the burden of identifying and managing health and safety risks. Without the benefit of a comprehensive health and safety training program, these young professionals may be putting both themselves and those under their supervision at risk. The Moura Mine explosions and the asbestos health disaster should not be just artifacts of history, but highly valued lessons that impress the need for comprehensive health and safety risk management strategies on young professionals. From the perspective of the former secretary of the Committee to implement the findings of the Moura (Disaster) Inquiry and as the former coordinator of the Coal Workers Health Scheme, key issues in occupational health and safety management systems are explored.

Jan 1, 2005