Search Documents

By W. J. Karwoski

A ground-support system for grizzly and haulage drifts was tested in Magma Copper Co.'s San Manuel mine. Eight two-piece, wide- flange steel sets were erected in a ventilation drift on the 2315 grizzly level. The sets were lagged with three different materials and back- packed with pea gravel and sand. The pillar on either side of the drift support system was instrumented with stressmeters and rock-bolt load cells, the backfill with pressure cells, and the steel sets with load cells. Results indicate a better survival rate than with typical monolithic concrete.

Jan 1, 1979

By G. T. Hong

A numerical model for use in design is developed to predict the stresses and axial and bending displacements in a drilled pier in expansive soils. The prediction is based on the horizontal swelling pressures and uplift forces which act on the side of the drilled pier. The exponential suction envelope with the depth within the moisture active zone is estimated based upon the equilibrium suction, moisture diffusion coefficients obtained from laboratory tests, and minimum suction at the ground surface of the site based on field conditions. The volume change of soil is based on suction variations, soil properties, overburden pressures, crack influences, and the relationship between moisture contents and suctions. Considering the movement active and anchor zones on a soil-pile system in expansive soils, horizontal swelling pressures are formulated using the shear strength of an unsaturated soil and the Mohr?s circle and failure envelope. The movement active zone has two sub-zones in which horizontal swelling pressures are attributed to passive earth pressure failure and suction change in the upper and lower sub-zones, respectively. Horizontal swelling pressures which occur in the anchor zone are assumed to be in the at rest condition. The shear stress generated on the vertical surface of a drilled pier is supported by the nonlinear curves of load transfer versus relative displacement. The axial behavior and lateral bending of the pier in expansive soils are simulated using a beam column approach. The computed axial and bending displacements and stresses are used to provide structural design of the pier. Figures of computed results for typical cases are presented.

Jan 1, 2007

By Ke Yang

Drilled shafts are widely adopted as the foundation for sound walls. However, there has been a lack of uniformity in design and analysis methods and design criteria, in terms of factor of safety against ultimate capacity failure as well as the allowable deflection. In order to establish a uniform design methodology for the drilled shafts supporting sound walls in cohesive and cohesionless soils, respectively, a database of full-scale lateral load tests on fully instrumented drilled shafts was collected. Based on the compiled database, existing design methods and design criteria of laterally loaded drilled shafts were evaluated. Broms method and COM624P (or LPILE) are suggested as the design methods for drilled shafts supporting sound walls in both cohesive and cohesionless soils. Additionally, the corresponding design criteria, including factor of safety and permissible deflection, for both design methods are recommended. Two full-scale lateral load tests on fully instrumented drilled shafts were subsequently conducted in Colorado to further verify the design recommendation. A comprehensive geotechnical investigation program was also carried out at the two new lateral load test sites that included pressuremeter test, SPT, as well as laboratory triaxial consolidated undrained tests and direct shear tests on the soil samples taken from the lateral load test sites. The test results obtained at these two load test sites were employed to validate the recommended geotechnical design and geotechnical testing methods for the drilled shafts supporting sound walls.

Jan 1, 2007

By Eric J. Beckman

Recovery of metals from dilute solution, whether the matrix is solid, or liquid, remains a considerable technical and financial challenge. Methods currently exist whereby metals can be extracted from either type of matrix, yet these methods consume significant quantities of reagents and can also generate multiple waste ,streams in the process. Technology developed in our lab allows efficient application of environmentally-benign CO2 to a number of separation problems involving metals. For example, we have employed biphasic mixtures of C02 and water as a green acid leach medium. Metals have been extracted from a steelmaking process residue and then recovered as metal carbonates through depressurization. In this process, metals are extracted and recovered without the use of reagents other than CO2 and water, and CO2 is sequestered as a solid. In addition, through synthesis of Cal-miscible phase transfer agents, we have shown that CO2 can replace the organic solvent currently used in refining of precious metals, The sensitivity to pressure of phase behavior in a CO2-mixture may allow significant streamlining of the process as well. Finally, CO2 soluble chelating agents have been used to extract toxic metals from acidic effluent such as that found in plating facilities.

Jan 1, 1999

By D Johansson, A Nordqvist, D Mihaylov, N Petropoulos, M Wimmer

The flowability of the caved rock masses in the sublevel caving (SLC) mining method is of great importance. During the blasting process of a SLC-ring, the caved rock mass in front of the ring is compacted. As a result of this compaction, the mechanical properties of the fractured rock masses change, for example void ratio, angle of internal friction and structure of the compacted material. The changed mechanical properties of caved rock mass and recent blasted material can influence the mobility of the material, which could result in blockage of the flow path of the material. The identification of the involved mechanisms in this process can be done after a series of tests in different scales. However, there is no available equipment for dynamic measurements during blasting, ie velocity and displacement of the burden and in the caved masses. This study focuses on the development and laboratory evaluation of a measuring system that can be installed in a borehole. The first trial was carried out in a pillar, where two blastholes had been drilled (9.5 m) parallel with the drift and two measuring holes (16.5 m) were perpendicular to the drift. Two measuring systems were installed in the measuring holes. Some preliminary tests were carried out to find suitable initiation procedures for the emulsion explosive. Applicability and robustness of the developed measuring system were also evaluated. In addition to these tests, an expandable cement mixture was developed to firmly anchor the measuring systems in the boreholes. The measuring system consists of an anchor, armoured cable in a pulling tube and a protective case. The anchor is equipped with uniaxial and triaxial accelerometers. A potentiometric measuring system for displacement up to 2 m is installed at the end of the pulling tube and connected to an extendable spiral cable. All sensors are connected to a data acquisition system (DAS). Both measuring systems have their own DAS to acquire data in case of failure of one of the systems. The measuring system was tested in laboratory conditions with impact velocity up to 10 m/s. It was proven to be functional and gave reliable results.CITATION:Petropoulos, N, Mihaylov, D, Johansson, D, Wimmer, M and Nordqvist, A, 2015. Design of equipment for dynamic burden measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 493–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Minghui Li

China is the largest coal producer in the world. In 2012, the coal production in China is 3.65billion tonnes, accounting for approximately 49% of global coal production. The raw coal production in 2012 was 3.8% more than the year 2011. 56% of total raw coal has been washed. The increase in raw coal production also promotes technology to be developed and brings separation capacity become larger and larger in coal processing in China. At present, over 40 extra-large scale coal preparation plants (each plant has capacity of more than 10 Mtpa) are in operation in China, the largest one is 32.5 Mtpa. Heavy medium separation are widely used in new built coal preparation, the washing limit for thermal coal feed lower and lower, the equipment selection tends larger which brings the whole washing system simplified, the local equipment developed and manufactured are more and more used. By discussing designs of several typical thermal coal preparation plants and coking coal preparation plants in China, this thesis introduces the current design of China?s extra-large coal preparation plants, and sums up the prevailing design features and trends of extra-large coal preparation plants.

Aug 1, 2013

By Nathaniel Arbiter

After almost 60 years of application in this country froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency, and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum--to mention only the most important metals occurring in the U.S. as sulphides--must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000 tons daily milling rate on copper ores. Table I (1) shows the trend in copper ore grades in U.S. in recent years:

Jan 1, 1970

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

By S C. Dominy

Grade control programs aim to deliver economic tonnes to the mill via accurate definition of ore and waste. The foundation of a successful program is high quality sampling supported by geology and a suitable data management and modelling system. Underground sampling methods include chip, channel and panel samples; grab/muck pile samples; and drill-based samples. Grade control strategy is related to mining method and orebody type. Sampling protocols must be designed to suit the style of mineralisation in question. Holistic studies focussing on ore mineralogy and gold particle deportment, size and distribution are required for sample collection and preparation protocol optimisation through ‘Theory of Sampling’ application. Where possible, such programs should be undertaken early in the life of a project. Appropriate assaying procedures are also required. Program implementation will require suitably skilled individuals to train and mentor staff, with ongoing Quality Assurance/Quality Control (QA/QC) monitoring and review will allow protocols and staff to be updated as required.

Aug 22, 2011

By Benjamin Jennings, Jason Herron

In the summer of 2016 Xcel Energy experienced a storm event that resulted in the collapse of approximately 8.5 miles of a 345 KV transmission line near Rogers, Minnesota. In design of the new transmission line, Xcel Energy determined that ten tower locations would be replaced with steel H-frame structures supported by helical piles instead of wood H-frame structures supported by driven wooden piles. A steel foundation was proposed for the towers due to time constraints and site conditions unfavorable to large pile driving equipment. Xcel Energy contacted the helical pile manufacturer Hubbell Power Systems, Inc. (HPS) for aid in the design of a complete steel foundation for the structure legs. With the shear, moment, and axial loads provided, the manufacturer used pile group modeling and axial capacity software to design a four helical pile group; and used 3D modeling and finite element software to design a moment resistant grillage to connect to the tower base. The steel grillage utilizes a new moment resistant connection and clamp system to transfer loads from the piles to the grillage. This connection provides a true fixed head condition and reduces lateral deflection issues typical to smaller diameter piles in pinned head connections. The clamp is designed to deform the helical pipe pile shaft and transfer the full axial load of the structure through the mechanical and friction connection. The helical piles and the moment resistant grillage were manufactured with shorter than average lead times and a helical pile installation contractor performed the installation. An expedient plan of install was developed by the contractor that resulted in an average installation rate of one complete set of tower foundations per day. The design of the moment resistant grillage, clamping system, and excellent foundation construction by the contractor provided an expedient and efficient foundation system to be discussed in this paper.

Jan 1, 2017

By D. J. Dunn

Grinding balls, simple in shape, are actually sophisticated machine components, and essential elements of mineral grinding mills. Their physical properties and quality must be adequate to achieve design life and grinding mission with few failures. Consistant properties and freedom from breakage are essential. Size, mass, hardness profile, chemistry, and microstructure are important variables which should be designed, specified, controlled, and verified to achieve optimal mill performance. Failure to specify ball properties in detail or failure to obtain required ball properties and quality can cause milling productivity losses and excessive costs that could endanger a milling operations survival in the competive mineral industry.

Jan 1, 1989

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By D Gericke, R Cooke

This paper presents an assessment of the status in design and operation of deep level backfill distribution systems by referring to case studies and practical experience. The improvements in design and operation of the systems can largely be attributed to an improved understanding of slurry flow behaviour and a corresponding integrated design approach that includes slurry flow modelling, system design and application of the latest technology. The conclusions summarise the lessons learnt from such case studies and stresses the importance of design reviews and audits of existing systems as a means to ensure that the mistakes of the past are not repeated in the future.

Jan 1, 1998

By George C. Toland

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control on the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. This paper discusses the types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent, and discusses in detail technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1975

By Yoichi Shimada, Katsuyuki Nishida, Shinichi Takahashi, Yasushi Okada, Yohei Nakamichi, Kazunori Oshiro, Taichi Terui, Sigehiko Sugie

"Temporary retaining walls are ordinarily used for tunnel construction work conducted using the opencut construction method. Retaining walls in such instances are typically installed vertically. However, shoring (such as struts and king posts) is required to ensure the stability of retaining walls in cases of excavation work to depths that exceed approximately 4 m. A new design and construction method that focuses on the effectiveness of retaining walls that are installed on an incline was studied with the aim of improving construction workability by omitting shoring. The inclined braceless excavation support (IBES) method, which was developed for use with the inclined buttress method, requires no shoring, even for deep-open-cut construction work and can be applied to deep excavation work on ground with a high groundwater level. This method has been applied at six work sites in Japan in recent years. This paper introduces the IBES design and construction method and presents verification results based on the design method, a model experiment, finite element analysis, and measurements obtained during construction work.INTRODUCTIONBackgroundIn the past, temporary retaining walls used in open-cut construction work have been installed vertically, and shoring (such as struts and king posts) has typically been used to ensure the stability of these retaining walls when the excavation depth reached 3–4 m. However, shoring interferes with structures built within excavations and requires box-outs and penetration sections in the structures, as well as concrete joints that raise concerns about their impact on the watertightness and long-term durability of structures (Figure 1).Shoring also narrows the space available for conducting construction work and reduces construction work efficiency, and the installation and removal of shoring increases the construction duration and cost. As a result, there has been a demand for ways to reduce or eliminate shoring to improve the quality of structures and construction work efficiency."

Jan 1, 2016

By Timothy P. Smirnoff, Tracy K. Lundin

INTRODUCTION The City of Phoenix, Arizona is located in the Phoenix Basin watershed which is prone to flash flooding several times each year. The runoff from these storms moves from the mountains in the north to the Salt River in the south. An extension of Interstate Highway 10 (1-10) will pass through the city east to west to form an Inner Loop through the downtown business district. PROJECT DESCRIPTION The I-10 Inner Loop extension will be a depressed roadway which would intercept the surface drainage of the Phoenix Basin and separate the watershed into two regions. To prevent flooding of the depressed roadway, runoff storm water collected from the northern half of the drainage area will be conveyed beneath the roadway to its natural outlet at the Salt River. A conveyance system composed of pressure tunnels beneath the city, shown in Figure 1, was proposed to achieve this goal . Table A presents the prominent features of each of the tunnels. This paper will describe geologic and engineering parameters specific to Phoenix which were used in the design of a series of tunnels to convey storm water from the I-10 Inner Loop to the Salt River. The design of tunnel initial and final support is described along with support and construction methods used by the Contractor.

Jan 1, 1985

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities, or 82 percent, may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible.

Jan 1, 2016

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008

By D. L. Petersen, C. R. Nelson, P. M. Bergson, B. K. Nelson

Membrane waterproofing systems in large tunnels cause the partial decoupling of the concrete liner from the rockbolted and shotcreted reinforced rockmass. This decoupling leads to a loose fit of the liner in the excavation when shrinkage from cooling and moisture loss occurs. This increases tensile stresses which require either the addition of reinforcing steel in excess of common European practice or the potential for liner cracking. Hot weather concrete placement and cold weather service conditions increase the magnitude of the problem, while creep of the rockmass reduces it. Contact grouting also reduces, but does not eliminate, the problem.

Jan 1, 1991